Deltaメーカー11-950の使用説明書/サービス説明書
ページ先へ移動 of 14
INSTRUCTION MANUAL 8" Bench Drill Pr ess (Model 11-950) P ART NO. 900591 (011) Copyright © 2001 Delta Machinery ESP AÑOL: PÁGINA 15 T o learn more about DEL T A MACHINER Y visit our website at: www .deltamachinery .com. For Parts, Service, W arranty or other Assistance, please call 1-800-223-7278 ( In Canada call 1-800-463-3582).
2 SAFETY RULES W oodworking can be dangerous if safe and pr oper operating procedures ar e not followed. As with all machinery , there are certain hazar ds involved with the operation of the product. Using the machine with respect and caution will considerably lessen the possibility of personal injury .
3 1. DO NOT operate your drill press until it is completely assembled and installed according to the instructions. 2. IF YOU ARE NOT thoroughly familiar with the operation of drill presses, obtain advice fr om your supervisor , instructor or other qualified person.
4 UNP ACKING Y our drill press is shipped complete in one container . Carefully unpack the drill pr ess and all loose items from the container . Figure 2 illustrates the drill press and all loose items supplied with the machine.
5 CLEANING Remove the protective coating fr om the machined surfaces of the drill press and all loose items. This coating may be removed with a soft cloth moistened with ker osene. DO NOT use acetone, gasoline, or lacquer thinner for this purpose. ASSEMBLING THE DRILL PRESS Fig.
6 Fig. 6 Fig. 7 Fig. 8 Fig. 9 4. Place the drill press head (F) Fig. 6, onto the column (A) as far as it will go. Align head to table and base and tighten the two head locking screws (G) with wr ench supplied. 5. Thread the thr ee pinion shaft handles (H) Fig.
7 Fig. 10 F ASTENING DRILL PRESS TO SUPPOR TING SURF ACE If during operation there is any tendency for the drill pr ess to tip over , slide or walk on the supporting surface, the drill press base must be secur ed to the supporting surface with fasteners through the two holes (A) Fig.
8 MOTOR SPECIFICA TIONS Y our drill press is wired for 110-120 volt, 60 HZ alternating current. Befor e connecting the machine to the power source, make sure the switch is in the “OFF” position. The motor pr ovides a no-load speed of 1725 RPM. Fig.
9 Fig. 14 Fig. 17 CHANGING SPEEDS AND ADJUSTING BEL T TENSION Fig. 16 SPINDLE SPEEDS Five spindle speeds of 620, 1100, 1720, 2340 and 3100 RPM are available with your drill pr ess. The highest speed is obtained when the belt is on the lar gest step of the motor pulley and the smallest step of the spindle pulley , as shown in Fig.
10 Fig. 18 Fig. 19 Fig. 20 Fig. 21 LOCKING SWITCH IN THE “OFF” POSITION When the tool is not in use, the switch should be locked in the “OFF” position to prevent unauthorized use of the tool. T o lock the switch in the “OFF” position, grasp the switch toggle (B) and pull it out of the switch, as shown in Fig.
11 Fig. 22 The spindle is automatically returned to its upper most position upon release of the handle. It is r ecommended that the handle be allowed to slowly return to the top position after all holes have been bored in the material. This spring has been properly adjusted at the factory and should not be disturbed unless absolutely necessary .
12 Fig. 25 Fig. 26 DRILLING HOLES TO DEPTH Where a number of holes ar e to be drilled to exactly the same depth, the stop nuts on the threaded stop r od are used as follows: 1. Lower the spindle until the pointer (A) Fig. 25, lines up with the mark on the scale (B) you wish the depth to be.
13 CORRECT DRILLING SPEEDS Factors which determine the best speed to use in any drill press operations ar e: material, size of hole, type of drill or other cutter , and quality of cut desired. The smaller the drill, the gr eater the RPM required. When drilling in soft materials, use a higher speed than what would be used for harder materials.
14 Delta Building T rades and Home Shop Machinery T wo Y ear Limited W arranty Delta will repair or r eplace, at its expense and at its option, any Delta machine, machine part, or machine accessory wh.
デバイスDelta 11-950の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Delta 11-950をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはDelta 11-950の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Delta 11-950の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Delta 11-950で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Delta 11-950を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はDelta 11-950の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Delta 11-950に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちDelta 11-950デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
