Deltaメーカー32-350の使用説明書/サービス説明書
ページ先へ移動 of 16
1 DA TED 7-15-96 INSTRUCTION MANUAL P ART NO. 1346961 © Delta International Machinery Corp. 1996 Horizontal Boring Machine (Model 32-350).
2 T ABLE OF CONTENTS SAFETY RULES ..............................................................................................................................................3 ADDITIONAL SAFETY RULES FOR BORING MACHINES .............................
3 SAFETY RULES W oodworking can be danger ous if safe and proper operating procedur es are not followed. As with all machinery , there ar e certain hazards involved with the operation of the pr oduct. Using the machine with respect and caution will considerably lessen the possibility of personal injury .
4 ADDITIONAL SAFETY RULES FOR BORING MACHINES 1. WARNING: Do not operate your boring machine until it is completely assembled and installed according to the instructions. 2. IF YOU ARE NOT thoroughly familiar with the oper- ation of boring machines, obtain advice from your super - visor , instructor , or other qualified person.
5 ASSEMBL Y Fig. 2 Fig. 3 Fig. 5 Fig. 4 ASSEMBLING ST AND AND MOUNTING FEET 1. Assemble front panel (A) Fig. 2, and r ear panel (B) to side panels (C) with eight 5/8 inch-long screws, lock- washers and hex nuts (D). NOTE: Holes (E) Fig. 2, in side panels (C) should be at the bottom of the stand during assembly .
6 Fig. 6 Fig. 8 Fig. 9 Fig. 10 Fig. 7 ASSEMBLING T ABLE TO MACHINE 1. Thread two lock knobs (A) Fig. 6, into holes (B) at the underside of table (C). 2. Place table (C) Fig. 7, onto ledge (D) Fig. 8, of machine. Align two holes in machine ledge (D) Fig.
7 Fig. 11 ASSEMBLING STOCK STOP TO T ABLE 1. Loosen two lock knobs (A) Fig. 11, located on the underside of table (B). 2. With the flat side of stock stop rod (C) Fig. 11, facing down, slide stop rod (C) thr ough holes at both ends of table (B) as shown, and fasten by rotating two lock knobs (A) clockwise.
8 CONNECTING BORING MACHINE TO POWER SOURCE A separate electrical circuit should be used for your boring machine. This cir cuit should not be less than #12 wire and should be pr otected with a 15 Amp time lag fuse or circuit br eaker .
9 INST ALLING AND REMOVING DRILL BITS 1. Make certain the machine is disconnected from the power source. 2. Remove four screws, two of which ar e shown at (A) Fig.
10 Fig. 18 Fig. 19 Fig. 20 Fig. 21 DUST CHUTE The machine features a handy built-in dust chute (P) Fig. 18, which allows wood chips to fall out of the way and keeps the depth stop clear for accurate repetitive boring operations. SETTING DRILLING DEPTH 1.
11 ST ARTING AND STOPPING DRILL ROT A TION 1. T o start drill rotation, push green start button (A) Fig. 24. 2. T o stop drill rotation, push red stop button (B) Fig. 24. 3. IMPORT ANT : The air supply must be on and the foot pedal depressed to lower work holddown and activate carriage movement.
12 Fig. 28 Fig. 25 FOOT PEDAL The foot pedal activates the movement of the work hold- down and the boring head carriage. 1. Pushing halfway down on foot pedal (A) Fig. 25, will lower the work holddown (B) Fig. 26, when set properly against the work surface as shown.
13 The forward speed/feed rate of carriage assembly (A) Fig. 32, is governed by the air pressure. T o adjust the speed/feed rate of carriage assembly (A) Fig. 32, proceed as follows: 1. Make certain the machine is disconnected from the power source. 2.
14 OPERA TION Fig. 33 Fig. 34 Fig. 35 Fig. 37 Fig. 36 Figs. 33 and 34, illustrate a typical end boring operation. Note that work holddown (A) Fig. 33, has been adjusted to hold workpiece (B) down on the table and that the end of workpiece (B) is firmly held against table fence (C) and miter gage (D).
15 MAINTENANCE Fig. 41 Fig. 38 Fig. 39 Fig. 40 LUBRICA TION The boring head assembly (A) Fig. 38, should be lubri- cated periodically with spindle grease Delta Part No. 999-02-023-1441 through the gr ease fitting (B). REPLACING BORING HEAD If it is ever necessary to remove the boring head for repair or r eplacement, proceed as follows: 1.
16 P AR TS, SERVICE OR WARRANTY ASSIST ANCE Printed in U.S.A. T wo Y ear Limited W arranty Delta Machinery Delta will repair or r eplace, at its expense and at its option, any Delta machine, machine p.
デバイスDelta 32-350の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Delta 32-350をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはDelta 32-350の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Delta 32-350の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Delta 32-350で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Delta 32-350を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はDelta 32-350の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Delta 32-350に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちDelta 32-350デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
