Deltaメーカー36-085の使用説明書/サービス説明書
ページ先へ移動 of 19
INSTRUCTION MANUAL 10" Dual Bevel Compound Power Miter Saw (Model 36-085) P ART NO. 901694 - 08-31-01 Copyright © 2001 Delta Machinery ESP AÑOL: PÁGINA 19 T o learn more about DEL T A MACHINER Y visit our website at: www .
GENERAL SAFETY RULES W oodworking can be dangerous if safe and proper operating pr ocedures ar e not followed. As with all machinery , certain hazards ar e involved with the operation of the product. Using the machine with r espect and caution will considerably lessen the possibility of personal injury .
3 3 ADDITIONAL SAFETY RULES FOR MITER SA WS 1. USE ONL Y CROSS-CUTTING SAW BLADES. When using carbide tipped blades, be certain that they have a neg- ative hook angle.
4 CONNECTING TOOL TO POWER SOURCE POWER CONNECTIONS A separate electrical circuit should be used for your tools. This cir cuit should not be less than #12 wire and should be protected with a 20 Amp time lag fuse.
5 Use proper extension cor ds. Make sure your extension cord is in good condition and is a 3-wir e extension cord which has a 3-prong gr ounding type plug and matching receptacle which will accept the tool’ s plug. When using an extension cord, be sur e to use one heavy enough to carry the current of the tool.
6 IMPORT ANT : DO NOT LIFT THE MITER SAW BY THE SWITCH HANDLE. THIS ACTION CAN CAUSE MIS- ALIGNMENT . AL WA YS LIFT THE MACHINE BY THE BASE OR CARR YING HANDLE .
7 Fig. 8 Fig. 9 Fig. 10 A B B C D E A TT ACHING STOCK STOP AND T ABLE EXTENSIONS 1. Decide on which side of the saw table you want the stock stop (A) Fig. 8, and attach the stock stop (A) on the table extension (B). 2. Insert the ends of table extension (B) Fig.
8 OPERA TING CONTROLS AND ADJUSTMENTS T ABLE HAZARD AREA WARNING: THE AREA INSIDE THE TWO RED LINES (A) FIG. 15 ON THE T ABLE IS DESIGNA TED AS A HAZARD ZONE. NEVER PLACE YOUR HANDS INSIDE THIS AREA WHILE OPERA TING THE TOOL. Fig. 15 A Fig. 13 F ASTENING MACHINE TO SUPPORTING SURF ACE Fig.
9 Fig. 17 Fig. 16 ST AR TING AND STOPPING THE MACHINE T o start the machine, squeeze the trigger (A) Fig. 16. T o stop the machine, release the trigger . This miter saw is equipped with an automatic electric blade brake. As soon as the trigger (A) Fig.
10 POINTER AND SCALE A pointer (B) Fig. 19 indicates the actual angle of cut. Each line on the scale (C) repr esents 1 degree. When the pointer is rotated fr om one line to the next on the scale, the angle of cut is changed by 1 degree. ADJUSTING POINTER T o adjust, loosen screw (D) Fig.
11 Fig. 22 Fig. 23 REAR SUPPOR T/CARR YING HANDLE A rear stabilizer bar (A) Fig. 22, is provided to pr event the miter saw from tipping to the r ear when the cuttinghead is returned to the up position after a cut has been made. For maximum support the bar (A) should be pulled out as far as possible.
12 Fig. 27 Fig. 28 ADJUSTING THE FENCE 90 DEGREES TO THE BLADE The fence (A) Fig. 27 should be adjusted so that it is 90 degrees to the blade. T o adjust: 1. DISCONNECT TOOL FROM POWER SOURCE . 2. First, adjust the blade so that it is parallel to the table slot.
13 2. Set the saw blade on the “0” degr ee positive miter stop. 3. Use one end of a squar e (A) Fig. 29 on the table and the other end against the blade. Check to see if the blade is 0 degrees to the table (Fig. 29). 4. If an adjustment is necessary , loosen the locknut (B) Fig.
TYPICAL OPERA TIONS AND HELPFUL HINTS 1. Before cutting, be certain that the cutting arm and table are at their corr ect settings and are firmly locked in place. Also, determine that the workpiece is the right size for the saw . 2. Firmly clamp the workpiece to the table against the fence.
15 Fig. 41 Fig. 42 CUTTING CROWN MOLDING One of the many features of a compound miter saw is the ease of cutting cr own molding. The following is an example of cutting both inside and outside corners on 52/38 degree wall angle crown molding.
2. Remove the scr ew (A) Fig. 45, and rotate the cover (B) to the rear (Fig. 46). 3. Depr ess the arbor lock (A) Fig. 47, to keep the blade from turning. 4. Use the supplied wr ench (D) Fig. 48 to loosen the arbor screw (E). T ur n it clockwise. 5. Remove the arbor scr ew (E), outside blade flange (F), and saw blade (G) from the saw arbor .
17 Fig. 49 Fig. 50 Fig. 51 BRUSH INSPECTION AND REPLACEMENT CAUTION: BEFORE INSPECTING THE BRUSHES, DISCONNECT THE TOOL FROM THE POWER SOURCE. Brush life varies, depending on the load on the motor . Check the brushes after the first 50 hours of use for a new machine, or after a new set of brushes has been installed.
18 T wo Y ear Limited W arranty Delta will repair or r eplace, at its expense and at its option, any Delta machine, machine part, or machine accessory which in normal use has proven to be defective in.
36 36 36 36 36 The following are trademarks of POR TER-CABLE · DEL T A (Las siguientes son marcas r egistradas de PORTER-CABLE S.A.): BAMMER ® , INNOV A TION THA T WORKS ® , JETSTREAM ® , LASERLOC.
デバイスDelta 36-085の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Delta 36-085をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはDelta 36-085の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Delta 36-085の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Delta 36-085で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Delta 36-085を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はDelta 36-085の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Delta 36-085に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちDelta 36-085デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
