Deltaメーカー36-312の使用説明書/サービス説明書
ページ先へ移動 of 17
INSTRUCTION MANUAL ESP AÑOL: PÁGINA 17 T o learn more about DEL T A MACHINER Y visit our website at: www .deltamachinery .com. For Parts, Service, W arranty or other Assistance, please call 1-800-223-7278 ( In Canada call 1-800-463-3582). 12" Single-Bevel Compound Miter Saw (Model 36-312) Patents Pending P ART NO.
2 Indicates an imminently hazardous situation which, if not avoided, will r esult in death or serious injury . Indicates a potentially hazardous situation which, if not avoided, could r esult in death or serious injury . Indicates a potentially hazardous situation which, if not avoided, may r esult in minor or moderate injury .
3 GENERAL SAFETY RULES 1. FOR YOUR OWN SAFETY , READ THE INSTRUC- TION MANUAL BEFORE OPERA TING THE MACHINE. Learning the machine’ s application, limitations, and specific hazards will gr eatly mini- mize the possibility of accidents and injury . 2.
4 ADDITIONAL SAFETY RULES FOR MITER SA WS Refer to them often and use them to instruct others . F AILURE TO FOLLOW THESE RULES MA Y RESUL T IN SERIOUS INJURY . 04-24-03 SA VE THESE INSTRUCTIONS . 1. DO NOT OPERA TE THIS MACHINE until it is completely assembled and installed according to the instructions.
5 Y our new Compound Miter Saw is DOUBLE-INSULA TED to give you added safety . As a result, this saw is equipped with a two-prong plug which permits you to use any conventional 120 volt electrical outlet with concern for maintaining a ground connection.
6 B Fig. 3A A ASSEMBL Y AND OPERA TION Fig. 3 C DA B Fig. 4 A TT ACHING DUST BAG 1. Attach dust spout (A) Fig. 3 to port (B). 2. Depress spring clips (C) Fig. 3 of dust bag (D) and clip dust bag (D) over rib of dust spout (A). MOVING CUTTINGHEAD TO THE UP POSITION Push down on the handle (B) Fig.
7 Fig. 5 A B C E D E Fig.6 FENCE OPERA TION The saw is supplied with left fence segment (A) Fig. 7 that incorporates a squeeze clamp feature. T o operate the fence segment or to slide to another location, squeeze the clamp (A) Fig. 7 to disengage the lock.
8 A B C D E B 1. The compound miter saw will cut any angle from a straight 0° cut to 48° right and left. T urn the locking knob (A) Fig. 13 counterclockwise, depr ess the lock lever (B), and rotate the table to the desired position. 2. This machine is equipped with positive stops at the 0° cut-off position and at the 15°, 22.
9 Fig. 16 C A D B DISCONNECT THE MACHINE FROM THE POWER SOURCE. Fig. 15 T o adjust the sliding fit between the movable table and the base, turn the nut (A) Fig.
DISCONNECT THE MACHINE FROM THE POWER SOURCE. 1. Position the bevel detent plate so that the desired angle (A) Fig. 23 is exposed immediately to the left of the housing (H) Fig. 23. 2. Lift the front handle (A) Fig. 22 to disengage bevel lock. 3. Tilt the cuttinghead left as desired until it stops on plate (A) Fig.
11 DISCONNECT THE MACHINE FROM THE POWER SOURCE. 1. Position the bevel detent plate so that the desired angle (A) Fig. 25 is exposed. 2. Lift the front handle (A) Fig. 26 to disengage the bevel lock. 3. Tilt the cuttinghead left until it stops on the plate (B) Fig.
If the size of the workpiece causes your hand to be inside the table hazard zone (see section “T ABLE HAZARD ZONE” SEE FIG. 21 ), use a clamp to secure the workpiece.
13 Fig. 36 CORRECT CUTTING BOWED MA TERIAL 1. Check the workpiece. If it is bowed, position the workpiece on the table as shown in Fig. 36. 2. When the workpiece is positioned the wrong way (Fig. 37), it will pinch the blade near the completion of the cut.
14 Fig. 42 A MAINTENANCE Disconnect the machine from the power sour ce. Fig. 43 E G C D H Fig. 44 F CHANGING THE BLADE J 1. Use only 12" diameter blades (with 1" arbor holes) that are rated for 5000 RPM or higher . 2. Use the supplied wrench to loosen scr ews (A) Fig.
15 Fig.46 B C Fig. 45 A A BRUSH INSPECTION AND REPLACEMENT Before inspecting brushes, disconnect the machine fr om the power source. Brush life varies, depending on the load on the motor . Check the brushes after the first 50 hours, or after a new set of brushes has been installed.
16 T wo Y ear Limited New Pr oduct W arranty Delta will repair or r eplace, at its expense and at its option, any new Delta machine, machine part, or machine accessory which in normal use has proven t.
The following are trademarks of POR TER-CABLE · DEL T A (Las siguientes son marcas registradas de POR TER-CABLE S.A.): Auto-Set ® , BAMMER ® , B.O.S.
デバイスDelta 36-312の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Delta 36-312をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはDelta 36-312の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Delta 36-312の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Delta 36-312で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Delta 36-312を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はDelta 36-312の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Delta 36-312に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちDelta 36-312デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
