Deltaメーカー40-650 Type 2の使用説明書/サービス説明書
ページ先へ移動 of 16
1 DA TED 11-25-98 INSTRUCTION MANUAL P ART NO. 1349463 © Delta International Machinery Corp. 1998 18" V ariable Speed Scr oll Saw (Model 40-650, T ype 2) Quick Quality Quiet.
2 T ABLE OF CONTENTS SAFETY RULES ..................................................................................................................................3 ADDITIONAL SAFETY RULES FOR SCROLL SA WS ............................................
3.
4 ADDITIONAL SAFETY RULES FOR SCROLL SA WS 1. WARNING: Do not operate your scr oll saw until it is completely assembled and installed according to the instructions. 2. IF YOU ARE NOT thoroughly familiar with the oper- ation of Scroll Saws, obtain advice fr om your supervi- sor , instructor or other qualified person.
5 Fig. 2 UNP ACKING AND CLEANING Y our new scroll saw and stand is shipped complete in one container . Carefully unpack the saw , stand and all loose items from the shipping container . Figure 2 illustrates the saw and all loose items and Figur e 3 illustrates the stand and all related parts.
6 Fig. 3 ASSEMBLING ST AND 1. Assemble the stand, as shown in Fig. 4, using the 24 carriage bolts, flat washers and hex nuts. NOTE: The round holes on the top of the two top braces (A) are to be positioned toward the r ear leg (B) and all three legs are positioned outside the bottom shelf and top braces.
7 Fig. 5 Fig. 6 Fig. 7 Fig. 8 3. Figure 8 illustrates the saw (H) fastened to the stand (J). Place the stand on a level sur- face and securely tighten all stand mounting hardwar e. 2. Fasten the rear of the saw to the stand using the two 5/8" long screws (F) Fig.
8 Fig. 9 Fig. 10 Fig. 11 Fig. 12 ASSEMBLING HOLDDOWN FOOT 1. With wrench supplied, assemble holddown foot (A) Fig. 10, to rod (B) using 1/2² hex sock- et head screw (C) with lockwasher and flat washer . Prongs of holddown foot (A) should straddle blade.
9 CONNECTING SCROLL SAW TO POWER SOURCE IMPORT ANT : BEFORE CONNECTING THE SAW TO THE POWER LINE, MAKE SURE THE SWITCH IS IN THE “OFF” POSITION. Fig.
10 F ASTENING ST AND TO SUPPOR TING SURF ACE If there is any tendency for the scr oll saw to move during operation, the scroll saw stand must be fastened to the floor . Fig. 17 OPERA TING CONTROLS AND ADJUSTMENTS ON-OFF POWER SWITCH The on-off switch (A) Fig.
11 Fig. 18 DUST BLOWER A dust blower (A) Fig. 18, is provided, and can be moved to direct air to the most ef fective point on the cutting line. ADJUSTING BLADE TENSION T ension is applied to the blade when the blade tension lever (A) Fig. 19, is in the rear position, as shown.
12 ADJUSTING CLAMPING ACTION OF BLADE HOLDERS Differ ent widths of scroll saw blades will make it necessary to adjust the clamping action of the blade holders. It should be noted, however , that very little adjustment is necessary and very little clamping force is requir ed to hold the blade satisfactorily .
13 Fig. 25 3. Push blade holder clamping lever (C) Fig. 25, to the rear as shown. This will automatically r elease the blade (D) from the upper blade holder (E). 4. Push lower blade holder clamping lever (F) Fig. 26, to the rear . This will automatically release blade (D) fr om lower chuck.
14 Fig. 27 Fig. 28 Fig. 29 Fig. 31 ADJUSTING 90 AND 45 DEGREE POSITIVE STOPS FOR T ABLE 1. Loosen table lock handle and move the table all the way to the left and tighten table lock handle. 2. Using a square (A) Fig. 29, check to see if the table is 90 degrees to the saw blade, as shown.
15 BRUSH INSPECTION AND REPLACEMENT CAUTION: BEFORE INSPECTING THE BRUSH- ES, DISCONNECT THE MACHINE FROM THE POWER SOURCE. Brush life varies. It depends on the load on the motor . Check the brushes after the first 50 hours of use for a new machine or after a new set of brushes has been installed.
16 BLADE BREAKAGE Blade breakage is usually caused by one or mor e of the following: 1. Bending the blade during installation. 2. Improper blade tension. 3. Improper blade selection for the work being cut. 4. Forcing the work into the blade too rapidly .
デバイスDelta 40-650 Type 2の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Delta 40-650 Type 2をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはDelta 40-650 Type 2の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Delta 40-650 Type 2の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Delta 40-650 Type 2で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Delta 40-650 Type 2を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はDelta 40-650 Type 2の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Delta 40-650 Type 2に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちDelta 40-650 Type 2デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
