DeltaメーカーSS250の使用説明書/サービス説明書
ページ先へ移動 of 20
INSTRUCTION MANUAL 16" V ariable Speed Scr oll Saw with Quickset II ® Blade Changing Featur e (Model SS250) P ART NO. 905574 - 05-03-02 Copyright © 2002 Delta Machinery ESP AÑOL: PÁGINA 21 T o learn more about DEL T A MACHINER Y visit our website at: www .
2 GENERAL SAFETY RULES W oodworking can be dangerous if safe and pr oper operating procedures ar e not followed. As with all machinery , there are certain hazar ds involved with the operation of the product. Using the machine with respect and caution will considerably lessen the possibility of personal injury .
ADDITIONAL SAFETY RULES FOR SCROLL SA WS 3 WARNING: F AILURE TO FOLLOW THESE RULES MA Y RESUL T IN SERIOUS PERSONAL INJUR Y . SA VE THESE INSTRUCTIONS. Refer to them often and use them to instruct others. 1. DO NOT OPERA TE your scroll saw until it is completely assembled and installed according to the instructions.
4 POWER CONNECTIONS A separate electrical circuit should be used for your machines. This cir cuit should not be less than #12 wire and should be protected with a 20 Amp time lag fuse.
Use proper extension cor ds. Make sure your extension cord is in good condition and is a 3-wir e extension cord which has a 3-prong gr ounding type plug and matching receptacle which will accept the machine’ s plug. When using an extension cord, be sur e to use one heavy enough to carry the current of the machine.
6 SCROLL SA W P AR TS Fig. 1 Fig. 2 Fig. 1 1. Scroll Saw with blade attached 1 Fig. 2 2. T able 3. Quickset Blade Changing Wr ench 4. Holddown Rod 5. 4mm Hex Wr ench 6. Locking Handle 7. M10 Flat W asher 8. Blank T able Insert 9. T able Insert 10. Special Screw M6x1x45mm (2) 11.
7 ASSEMBL Y 1. Remove the blade from the scr oll saw . 2. Move the blade lever tension handle (A) Fig. 3, to the forewor d position as shown. 3. Push chuck locking lever (B) Fig. 4 to the rear as shown. This will release the blade (C) fr om the upper chuck assembly (D).
8 Fig. 7 5. Position table (A) Fig. 7, on the machine as shown. Align the two holes in the table trunnions (O) with the two holes in the base (P) of the machine. NOTE: BEFORE TIGHTENING THE M6x1x45mm SPECIAL SCREWS (B) AND M6 LOCKNUTS (C) FIG. 7, MAKE SURE THE TIL T SCALE (D) FIG.
9 9. Using the 4mm wrench (L) Fig. 11, loosen the two screws (P) on bottom of bracket (M) that fasten bracket to rod (N). Fig. 11 Fig. 12 10. Rotate bracket (M), to the position shown in Fig. 12. Loosen lock handle (R) and insert holddown rod (S) into hole in bracket (M), as shown.
10 F ASTENING SCROLL SA W TO SUPPOR TING SURF ACE Y our scroll saw MUST be securely fastened to a stand or workbench using the holes in the four rubber feet, three of which ar e shown at (A) Fig. 16. IMPORT ANT : When mounting the saw to a stand or workbench DO NOT over -tighten mounting bolts.
11 T ABLE INSER T The table insert (A) can be assembled to the saw table with the opening in the insert pointing to the front of the table, as shown in Fig. 19, or to the right as shown in Fig. 20. With the table in the level position, 90 degrees to the blade, the insert (A) should be positioned, as shown in Fig.
12 3. Push chuck locking lever (C) Fig. 23, to the rear as shown. This will release the blade (D) fr om the upper chuck (E). Fig. 23 C D E 4. Insert long end (F) Fig. 24, of quickset blade wrench into hole (G) in lower blade holder . This will align wrench (H) with blade holder screw (J).
13 ADJUSTING BLADE TENSION T ension is applied to the blade when the blade tension lever (A) Fig. 27, is in the rear position, as shown. When the lever (A) is moved forward, as shown in Fig. 28, blade tension is released. When adjusting blade tension, lever (A) should be in the forward position, as shown in Fig.
14 Fig. 30 Fig. 31 TIL TING THE T ABLE The table on your scroll saw can be tilted 45 degr ees to the left for bevel cutting operations by loosening table lock handle (A) Fig. 30, tilt the table to the desired angle and tighten lock handle (A). When bevel cutting, the holddown (B) Fig.
15 ADJUSTING HOLDDOWN The holddown (A) Fig. 34, should be adjusted so it contacts the top surface of the work being cut by loosening lock handle (B) and moving holddown rod (C) up or down. Then tighten lock handle (B). ADJUSTING DUST BLOWER The dust blower (A) Fig.
16 INSIDE CUTTING Inside cutting is where the blade must be thr eaded through a hole in the workpiece. The Delta 16" Scroll Saw has the capability of performing this operation quickly and easily as follows: Fig. 36 Inside cutting can be accomplished quickly with the Delta saw .
17 LUBRICA TION Fig. 39 Fig. 40 Fig. 42 1. DISCONNECT MACHINE FROM POWER SOURCE. 2. Remove four screws (A) Fig. 39, and r emove side panel (B) from the scr oll saw . 4. Lubricate the shafts of two special screws (D) Fig. 41, with a few drops of light machine oil in the ar eas where they pass thr ough the connecting link (E).
18 NOTES.
19 NOTES.
T wo Y ear Limited W arranty Delta will repair or r eplace, at its expense and at its option, any Delta machine, machine part, or machine accessory which in normal use has proven to be defective in wo.
デバイスDelta SS250の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Delta SS250をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはDelta SS250の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Delta SS250の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Delta SS250で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Delta SS250を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はDelta SS250の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Delta SS250に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちDelta SS250デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
