DenonメーカーAVR-3808の使用説明書/サービス説明書
ページ先へ移動 of 44
- 1 - DENON AVR control protocol Ver. 5.2.0_a Application model : AVR-3808/AVC-3808 Application terminal: RS-232C/ Ethernet Connector specificat ion Ⅰ .
- 2 - Ⅱ . Ethernet Connector type ： RJ-45(10BASE-T/100BASE-TX) Communication format ： Communication system : A half duplex Communication speed : 10Mbps/100Mbps Communication port : TCP port 23 (.
- 3 - NETWORK SETUP of AVR-4308 >Procedure of Network Setup mode. (1)Press SYSTEM SETUP button, then System Setup Me nu appears on FL-display(and GUI) (2)Select “Network Setup > Detail” . (3)Set parameters described below. <DHCP> "ON"---Use this setting when DHCP server is on the local network.
- 4 - Ⅱ . Ethernet Connector type ： RJ-45(10BASE-T/100BASE-TX) Communication format ： Communication system : A half duplex Communication speed : 10Mbps/100Mbps Communication port : TCP port 23 (.
- 5 - NETWORK SETUP of AVR-3808 >Procedure of Network Setup mode. (1)Press SYSTEM SETUP button, then System Setup Me nu appears on FL-display(and GUI) (2)Select “Network Setup > Detail” . (3)Set parameters described below. <DHCP> "ON"---Use this setting when DHCP server is on the local network.
- 6 - Protocol speci fication The following three data forms are defined. COMMAND : The message sent to a system(AVR) from a controlle r(Touch Panel etc.) A command to a system is given from a controller. EVENT : The message sent to a controller (Touch Panel etc.
- 7 - The example of a command * <CR> is the meaning of 0x0D. SIDVD<CR> : Select Input source DVD MSSTEREO<CR> : surround Mode Set to STEREO MVUP<CR> : Master Volume UP PWON<.
- 8 - Others A) COMMAND is receivable also during transmission of EVENT . B) Since CHANNEL VOLUME changes simultaneou sly when the SURROUND MODE changes, the value of t he channel volume of all channels returns as EVENT . C) CHANNEL VOLUME returns the data of A LL channels by the presen t SURROUND MODE also including an intact channel.
- 9 - COMMAND and PARAMETER list COMMAND PARAMETER function example PW ON POWER ON/S TANDBY change PWON<CR> STANDBY PWSTANDBY<CR> ? Return PW Status PW?<CR> MV UP MASTER VOL UME UP/D.
- 10 - COMMAND PARAMETER function example CV SB UP ---SURROUND BACKch (SBch 1SP) CVSB UP<CR> SB DOWN CVSB DOWN<CR> SB ** **:00 to 99 by ASCII , 50=0dB CVSB 50<CR> ? Return CV Status .
- 1 1 - COMMAND PARAMETER function example SD AUTO set AUTO mode (Prior ity:HDMI>>DIGITAL>>ANALOG) SDAUTO<CR> HDMI set force HDMI INPUT mode SDHDMI<CR> DIGITAL set force DIGITAL INPUT (Optical,Coaxial)mode SDDIGITAL<CR> ANALOG set force ANALOG INPUT mode SDANALOG<CR> EXT.
- 12 - COMMAND PARAMETER function example MS CLASSIC CONCERT MSCLASSIC CONCERT<CR> MONO MOVIE MSMONO MOVIE<CR> MATRIX MSMATRIX<CR> VIDEO GAME MSVIDEO GAME<CR> VIRTUAL MSVIRTUAL.
- 13 - COMMAND PARAMETER function example PS TONE DEFEAT ON PARAMETER setting PSTONE DEFEAT ON<CR> TONE DEFEAT OFF TONE DEFEAT ON/OFF PSTONE DEFEAT OFF<CR> TONE DEFEAT ? Return PSTONE DEFE.
- 14 - COMMAND PARAMETER function example PS TRE UP TREBLE UP/DOWN , direct change to **dB PSTRE UP<CR> TRE DOWN **:00 to 99 by ASCII , 50=0dB PSTRE DOWN<CR> TRE ** ---AVR-3808 can be oper.
- 15 - COMMAND PARAMETER function example PS PAN ON PANORAMA O N/OFF PSPAN ON<CR> PAN OFF PSPAN OFF<CR> PAN ? Return PSPAN Status PSPAN ?<CR> DIM UP DIMENSION UP/DOWN , direct change.
- 16 - COMMAND PARAMETER function example PS NIGHT OFF NIGHT MODE direct change PSNIGHT OFF<CR> NIGHT LOW PSNIGHT LOW<CR> NIGHT MID PSNIGHT MID<CR> NIGHT HI PSNIGHT HI<CR> NIGH.
- 17 - Z2 COMMAND : "*" parameter uses two ASCII characte rs. (see page4 J) section) COMMAND PARAMETER function example Z2 PHONO MULTI ZONE-2 mode set , and select source at AVR-3808 Z2PHONO<CR> | ---The name of PARAMETER is | IPOD the same as that of the time of SI COMMAND.
- 18 - Z2 COMMAND : "*" parameter uses two ASCII characte rs. (see page4 J) section) Except Japan model. COMMAND PARAMETER function example Z2PS BAS UP ZONE2 BASS UP/DOWN , direct change to .
- 19 - Z3 COMMAND : "*" parameter uses two ASCII characte rs. (see page4 J) section) Except Japan model COMMAND PARAMETER function example Z3 PHONO MULTI ZONE-3 mode set , and select source at AVR-3808 Z3PHONO<CR> | ---The name of PARAMETER is | IPOD the same as that of the time of SI COMMAND.
- 20 - Z3 COMMAND : "*" parameter uses two ASCII characte rs. (see page4 J) section) Except Japan model COMMAND PARAMETER function example Z3PS BAS UP ZONE3 BASS UP/DOWN , direct change to *.
- 21 - ※ ANALOG TUNER Control (AVR model only) COMMAND PARAMETER function example TF ANUP TUNER Frequency UP/DOWN TFANUP<CR> ANDOWN TFANDOWN<CR> AN****** (6 digits) --- ****.** kHz at AM band (>050000 is AM.) ****.** MHz at FM band (<050000 is FM.
- 22 - ※ XM Control(North America model only) COMMAND PARAMETER function example TF XMUP XM Channel UP/DOWN TFXMUP<CR> XMDOWN TFXMDOWN<CR> XM*** (3 digits) --- ***:XM CH No. TFXM001<CR> (XM001 CH at XM) XM? Return TFXM Status TFXM?<CR> TP XMUP XM PRESET CH UP/DOWN , direct change to No.
- 23 - ※ iRadio/mServer/USB Extended Control COMMAND PARAMETER function example SI USB Select INPUT source NET/USB and USB Start Playback SIUSB<CR> Z2 USB Select MULTI ZONE-2 source NET/USB an.
- 24 - ※ iPod Extended Control COMMAND PARAMETER function example IP 90 “Cursor Up” Control IP90<CR> 91 “Cursor Down” Control IP91<CR> 92 “Cursor Left” Control IP92<CR>.
- 25 - ※ Cursol/Enter/Menu(Setup) COMMAND PARAMETER function example MN CUP “Cursor Up ” Control MNCUP<CR> CDN “Cursor Down” Control MNCDN<CR> CLT “Cursor Left” Control MNCLT.
- 26 - ※ Remote Lock/Panel Lock COMMAND PARAMETER function example SY REMOTE LOCK ON REMOTE CONTROL LOCK ON/OFF SYREMOTE LOCK ON<CR> REMOTE LOCK OFF SYREMOTE LOCK OFF<CR> PANEL LOCK ON PANEL BUTTON(Except MASTER VOL.)CONTROL LOCK ON SYPANEL LOCK ON<CR> PANEL+V LOCK ON PANEL BUTTON & MASTER VOL.
- 27 - EVENT(or RESPONSE) and PARAMETER list EVENT PARAMETER function example PW ON POWER ON/STANDBY change PWON<CR> STANDBY PWSTANDBY<CR> MV ** MASTER VOLUME change , **:00 to 99 by ASCII.
- 28 - EVENT PARAMETER function example SI NET/USB SINET/USB<CR> XM (North America model Only) SIHDRADIO<CR> USB SIUSB<CR> IPOD SIIPOD<CR> ZM ON MAIN-ZONE ON/OFF change ZMON<.
- 29 - EVENT PARAMETER function example MS DIRECT SURROUND mode change MSDIRECT<CR> PURE DIRECT MSPURE DIRECT<CR> STEREO MSSTEREO<CR> MULTI CH IN MSMULTI CH IN<CR> MULTI CH IN .
- 30 - EVENT PARAMETER function example MS DTS NEO:6 C MSDTS NEO:6 C<CR> DTS NEO:6 M MSDTS NEO:6 M<CR> DTS SURROUND MSDTS SURROUND<CR> DTS ES DSCRT6.
- 31 - EVENT PARAMETER function example MS NEURAL (North America model Only) MSNEURAL<CR> DOLBY D+ MSDOLBY D+ <CR> DOLBY D+ +EX MSDOLBY D+ +EX<CR> DOLBY D+ +PL2x C MSDOLBY D+ +PL2X C.
- 32 - EVENT PARAMETER function example PS TONE DEFEAT ON TONE DEFEAT ON/OFF change PSTONE DEFEAT ON<CR> TONE DEFEAT OFF PSTONE DEFEAT OFF<CR> SB:MTRX ON SURROUND BACK MODE change PSSB:MTR.
- 33 - EVENT PARAMETER function example PS DRC AUTO DRC change PSDRC AUTO<CR> DRC LOW PSDRC LOW<CR> DRC MID PSDRC MID<CR> DRC HI PSDRC HI<CR> DRC OFF PSDRC OFF<CR> DCO OFF D.
- 34 - EVENT PARAMETER function example PS DELAY *** AUDIO DELAY change, ***:000 to 999 by ASCII PSDELAY 200<CR> ---AVR-3808 ： 200=200ms （ MAX ） 100=100ms, 000=0ms NIGHT OFF NIGHT MODE cha.
- 35 - EVENT PARAMETER function example Z2 PHONO MULTI ZONE-2 source change Z2PHONO<CR> | ---The name of PARAMETER is | IPOD the same as that of the time of SI COMMAND.
- 36 - EVENT PARAMETER function example Z3 PHONO MULTI ZONE-3 source change Z3PHONO<CR> | ---The name of PARAMETER is | IPOD the same as that of the time of SI COMMA ND.
- 37 - ※ ANALOG TUNER Control(AVR model only) EVENT PARAMETER function example TF AN****** (6 digits) TUNER Frequency change TFAN105000<CR> --- ****.** kHz at AM band (1050.00kHz at AM) ****.** MHz at FM band TP AN**(PRESE T No.) TUNER PRESET change to No.
- 38 - ※ iRadio/mServer/USB Extended Control EVENT PARAMETER function NSA Onscreen Display Information is Answered By the NSA Command. 0 Display Line1 Information NSA0**************_?????<CR> .
- 39 - EVENT PARAMETER function NSE Onscreen Display Information(mserver/iRadio) is Answered By the NSE Command. 0 Display Line1 Information NSE0**************_?????<CR> 1 Display Line3 Informat.
- 40 - ※ iPod Extended Control EVENT PARAMETER function IPA Onscreen Display Information is Answered By the IPA Command. 0 Display Line1 Information IPA0***************_???<CR> 1 Display Line3.
- 41 - EVENT PARAMETER function IPA <example1> IPA0Artist??????????????????<CR> IPA1 ※ Ana Caram_????????????<CR> IPA2 ※ Badi Assad_???????????<CR> IPA3 ※ Christy Baron_?.
- 42 - EVENT PARAMETER function IPE Onscreen Display Information(iPod) is Answered By the IPA Command. 0 Display Line1 Information IPE0***************_???<CR> 1 Display Line3 Information IPE1 .
- 43 - EVENT PARAMETER function IPE <example1> IPE0Artist??????????????????<CR> IPE1 ※ Ana Caram_????????????<CR> IPE2 ※ Badi Assad_???????????<CR> IPE3 ※ Christy Baron_?.
- 44 - ※ Remote Lock/Panel Lock EVENT PARAMETER function example SY REMOTE LOCK ON REMOTE CONTROL LOCK ON/OFF SYREMOTE LOCK ON<CR> REMOTE LOCK OFF SYREMOTE LOCK OFF<CR> PANEL LOCK ON PANEL BUTTON(Except MASTER VOL.)CONTROL LOCK ON SYPANEL LOCK ON<CR> PANEL+V LOCK ON PANEL BUTTON & MASTER VOL.
デバイスDenon AVR-3808の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Denon AVR-3808をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはDenon AVR-3808の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Denon AVR-3808の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Denon AVR-3808で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Denon AVR-3808を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はDenon AVR-3808の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Denon AVR-3808に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちDenon AVR-3808デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
