AirlinkメーカーEDGE/GPRSの使用説明書/サービス説明書
ページ先へ移動 of 157
Copyright © 1993-2007 AirLink Co mmunica tions, Inc. All rights reserved. PinPoint-E EDGE/GPRS User Guide V ersion 2.32 - April 2007.
PinP oint-E E DGE/GPR S - User Guide, versi on 2.32 ii Information in this document is subject to change withou t notice. ©Copyright AirLink Communications, Inc.
PinPoint-E EDGE/GPRS - User Guide, version 2.32 iii Contents Introduction to PinPoint -E EDGE/GPRS . . . . . . . . . . . . . . . . . . . . . . . . . . 1 EDGE/GPRS Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PinPoint-E EDGE/GPRS - User Guide, version 2.32 iv Contents UDP Multicast Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 TCP P A D . . . . . . . . . . . . . . . . . . . . . . . .
PinPoint-E EDGE/GPRS - User Guide, version 2.32 v Contents NMEA Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 S tr eaming NMEA Messages ov e r the local port . . . . . . . . . .
PinPoint-E EDGE/GPRS - User Guide, version 2.32 vi Contents EDGE/HSDP A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 16 PPPoE: Point to Point Protocol over Ethernet . . . . .
PinPo int-E E DGE/GPRS - User Guide, version 2.32 1 CHAPTER 1 Intr oduction to PinPoint-E EDGE/GPRS FIGURE 1. PinPoint-E front and back EDGE/GPRS Overview The PinPoint-E's rugged form factor is ideal for industrial and co mmercial applications that require real-time communications.
PinPo int-E E DGE/GPRS - User Guide, version 2.32 2 Introduction to PinPoint-E EDGE/GPRS Establishing an Internet Connection The PinPoint-E uses Y our W ireless Service Provider as an ISP (Internet Se rvice Provider) to con - nect you to the Internet.
PinPo int-E E DGE/GPRS - User Guide, version 2.32 3 Introduction to PinPoint-E EDGE/GPRS data on another computer system, or other client fu nctions (such as data only be ing sent out or only being received after an initial request).
PinPo int-E E DGE/GPRS - User Guide, version 2.32 4 Introduction to PinPoint-E EDGE/GPRS FIGURE 3. V ehicle T racking and Mo bile Internet Access.
PinP oint-E E DGE/GPR S - User Guide, versi on 2.32 5 CHAPTER 2 Activation of the PinPoint-E T o in st all the SIM, you will only need a small phillips head screw driver . a. Unplug the PinPoint-E’ s power and all cables. b. Using a small phillips head screw driver, remove the screws on the back of the PinPoint-E.
PinP oint-E E DGE/GPR S - User Guide, versi on 2.32 6 Activation of the PinPoint-E b. Slide the tray out of the slot. FIGURE 3. Empty SIM T ray a. Place the SIM into the tray and ge ntly press to click it into place. FIGURE 4. SIM T ray with a SIM b. Slide the tray back into the modem an d gently press to c lick it into place.
PinP oint-E E DGE/GPR S - User Guide, versi on 2.32 7 Activation of the PinPoint-E a. Slide the PinPoint-E back into the case. b. Secure the back of the PinPoi nt-E with the screw s. Setting the APN with Wireless Ace The APN (Access Point Na me) is the way your m odem knows how it will be communicating with the network.
PinP oint-E E DGE/GPR S - User Guide, versi on 2.32 8 Activation of the PinPoint-E FIGURE 6. Wireless Ace: Connect FIGURE 7. Wireless Ace: EDGE/HSDP A FIGURE 8. Wireless Ace: *NET APN 3. Select EDGE/HSDP A from the menu on the left side of W ireless Ace (under “Groups”).
PinP oint-E E DGE/GPR S - User Guide, versi on 2.32 9 Activation of the PinPoint-E FIGURE 9. Wireless Ace: Common - Misc B. Enter the NAI into the new value field for *NETUID and enter your network password into the new value field for *NETPW . FIGURE 10.
PinP oint-E E DGE/GPR S - User Guide, versi on 2.32 10 CHAPTER 3 Utilities for the PinPoint-E AirLink offers a suite of utilities to o ptimize your PinPoint-E’ s performance, allowing yo u to remotely view status and make chan ges to the configuration as needed.
PinP oint-E E DGE/GPR S - User Guide, versi on 2.32 11 Utilities for the PinPoint-E Wireless Ace W ireless Ace enables modems equipped with ALEOS to be monitored and configured locally or remotely .
PinP oint-E E DGE/GPR S - User Guide, versi on 2.32 12 Utilities for the PinPoint-E FIGURE 3. Wireless Ace AceNet AceNet’ s remote connections use TCP/IP , UDP , or SMS. AceNet is a separate product which can be purcha sed from AirLink. Contact your AirLink repre - sentative for more information.
PinP oint-E E DGE/GPR S - User Guide, versi on 2.32 13 Utilities for the PinPoint-E FIGURE 4. AceNet FIGURE 5. AceNet Charting Modem Doctor Modem Doctor is a troubleshooti ng and di agnostics utility .
PinP oint-E E DGE/GPR S - User Guide, versi on 2.32 14 Utilities for the PinPoint-E FIGURE 6. Modem Docto r.
PinP oint-E E DGE/GPR S - User Guide, versi on 2.32 15 CHAPTER 4 IP Manager and DNS If you have a fleet of AirLink modems or even if you only have one, it can be difficult to keep track of the current IP addresses, esp ecially if the addresses aren’t st atic but change every time the modems connect to Y our W ireless Service Provider.
PinP oint-E E DGE/GPR S - User Guide, versi on 2.32 16 IP Manager and DNS Fully Qualified Domain Name A domain name is a name of a server or device on the Internet which is associated with an IP address.
PinP oint-E E DGE/GPR S - User Guide, versi on 2.32 17 IP Manager and DNS Dynamic Names When an IP address is no t expected to change, th e DNS server can indicate to all queries that the address can be cached and not look ed up for a long period of ti me.
PinP oint-E E DGE/GPR S - User Guide, versi on 2.32 18 IP Manager and DNS *MODEMNAME: The name you wa nt fo r the m odem. *DOMAI N: The domain name to be used by the modem. *IPMANAGER1 and *IPMANAGER2: The IP address or domain name of th e dynamic DNS server which is running IP Manager .
PinP oint-E E DGE/GPR S - User Guide, versi on 2.32 19 IP Manager and DNS DNS: Using Names Instead of IP addresses The PinPoint-E has the ability to query DNS servers in orde r to translate domain names into IP addresses. This allows you to use domain names in place of IP addresses for most of the configu - ration options requiring IP addresses.
PinP oint-E E DGE/GPR S - User Guide, versi on 2.32 20 IP Manager and DNS Note: If you will be using your PinPoint-E to co mmunicate with an other AirLink modem and both are using IP Manager to translate dynamic IP addresses to domain names, it is recommended that yo u set *DNSUSER to the IP address for IP Manager .
PinP oint-E E DGE/GPR S - User Guide, versi on 2.32 21 CHAPTER 5 Data Communication and Host Modes The PinPoin t-E plays th e part of a HOST when a computer or another device is connected to its serial or Ethernet port. The PinPoint-E can also route data to/from the connected device to the cel - lular network.
PinP oint-E E DGE/GPR S - User Guide, versi on 2.32 22 Data Communication and Host Modes AT M o d e Using a terminal connection, A T commands are used to configur e the modem , command it t o do something, or query a setting. For a full li sting of the A T commands, refer to page 62.
PinP oint-E E DGE/GPR S - User Guide, versi on 2.32 23 Data Communication and Host Modes FIGURE 1. Wireless Ace: PassThru Some internal hardware req uires upwards of 20 seconds before A T commands can be entered, so be patient if there seems to be no response to A T commands.
PinP oint-E E DGE/GPR S - User Guide, versi on 2.32 24 Data Communication and Host Modes FIGURE 3. Wireless Ace: T elnet Configuration If you need to change th e port fo r T elnet (for example, you h ave the default port blo cked on your firewall), the option is on the Oth er tab.
PinP oint-E E DGE/GPR S - User Guide, versi on 2.32 25 Data Communication and Host Modes FIGURE 5. Wireless Ace: PPP/Ethernet Using a private IP insulates the PPP client from changes in IP addresses of the underlying net - work. The will p erform basic NA T -like address translatio n on all packets.
PinP oint-E E DGE/GPR S - User Guide, versi on 2.32 26 Data Communication and Host Modes • Incoming UDP packets will be processed out th e seri al port if • UDP auto answer is enabled ( S82=2 ); .
PinP oint-E E DGE/GPR S - User Guide, versi on 2.32 27 Data Communication and Host Modes Reliable UDP adds a simple protocol on top of UDP to provide reliable delivery of data. When data is received from the host serial port, a 2 by te header is added to the data, containing a mes - sage type and a sequence number .
PinP oint-E E DGE/GPR S - User Guide, versi on 2.32 28 Data Communication and Host Modes Public and Private Mode TCP packet assembly is af fected by the values of S50 (P AD Forwarding Time-out) and S51 (P AD Forwarding Character).
PinP oint-E E DGE/GPR S - User Guide, versi on 2.32 29 Data Communication and Host Modes Note: When using Public mode, connect the modem directly to the computer or other end device.
PinP oint-E E DGE/GPR S - User Guide, versi on 2.32 30 Data Communication and Host Modes Routing, at its most basic level, is the process of forwarding data on to the correct destination. One component of routing is add ress determination, directing data to the correct address either as its final destination or so it can be forwarded on.
PinP oint-E E DGE/GPR S - User Guide, versi on 2.32 31 Data Communication and Host Modes Keepalive Keepalive is used to test the PinPoint-E’ s connection by pinging an IP address after a specified period of inactivity .
PinP oint-E E DGE/GPR S - User Guide, versi on 2.32 32 CHAPTER 6 Exter nal Inputs & Power Contr ol The PinPoint-E has special features for use in a mobile environm ent. Th e PinPoint-E can be con - figured to monit or the inputs on i ts serial port and respond to speci fic types of events.
PinP oint-E E DGE/GPR S - User Guide, versi on 2.32 33 External Inputs & Power Control When the switch is closed and with *PPINPUTEVT configured, a RAP report will be sent to the destination IP address i ndicating that a contact closure has ta ken place (an external physical event has occurred).
PinP oint-E E DGE/GPR S - User Guide, versi on 2.32 34 External Inputs & Power Control FIGURE 4. DTR and R TS switches using Pin 5 (sign a l GND) as the common ground Power Modes FIGURE 5.
PinP oint-E E DGE/GPR S - User Guide, versi on 2.32 35 External Inputs & Power Control Power Effect on Modem S tate Once the transition from powered on to standby , lo w-p ower mode starts, the modem will change state to A T mode. This results in the current m ode being gracefully termin ated.
PinP oint-E E DGE/GPR S - User Guide, versi on 2.32 36 CHAPTER 7 Global Positioning System (GPS) The PinPoint-E is equipped with a GPS receiver to ascertain its pos ition to track the movements of a vehicle or other devices which move. The PinPoint-E relays the information of its location as well as other data for use with tracking applicati ons.
PinP oint-E E DGE/GPR S - User Guide, versi on 2.32 37 Global Positioning System (GPS) The GPS data is then transmitted to a central location which uses a tracking application to compile information about location, m ovement rates, and other pertinen t data.
PinP oint-E E DGE/GPR S - User Guide, versi on 2.32 38 Global Positioning System (GPS) Datum In addition to different reporting protocols, the PinPoi nt-E supports the most widely used GPS datum. The GPS datum is the method of ascertaining the posit ion of the GPS dev ice using a spe - cific reference point location.
PinP oint-E E DGE/GPR S - User Guide, versi on 2.32 39 Global Positioning System (GPS) Configuring the PinPoint-E for GPS T o configure your modem’ s GPS settings, you can us e either W ireless Ace or a terminal connection to configure the modem using A T comm ands ( page 62 ).
PinP oint-E E DGE/GPR S - User Guide, versi on 2.32 40 Global Positioning System (GPS) FIGURE 2. Wireless Ace: *PPIP and *PPPOR T Local Host T o set the PinPoin t-E to report to a local host, one directly connected to the PinPoint-E’ s Ethernet port, configure the port to be used with S53 - Destination Port .
PinP oint-E E DGE/GPR S - User Guide, versi on 2.32 41 Global Positioning System (GPS) FIGURE 6. Wireless Ace: *PPGPSR and *PPLA TSR 0 - *MF , Legacy reports for use wit h A T S version 4 and older . 11 - Global Positioning System (GPS) data. 12 - GPS data with the UTC time and date.
PinP oint-E E DGE/GPR S - User Guide, versi on 2.32 42 Global Positioning System (GPS) If you are sending reports on the local Ethernet port, and/or if you want them sent autom a tical ly , you will ne ed to set *PPLA TS . The time interval, just as for *PP TIME, is in seconds.
PinP oint-E E DGE/GPR S - User Guide, versi on 2.32 43 Global Positioning System (GPS) If you need to use a dynamic IP address for the host server , you can use th e RAP config uration command to change the va lue for *PPIP (see below). FIGURE 1 1. Wireless Ace: *PPI GNOREIP RAP Reports over a Local Connection (PPP or SLIP) FIGURE 12.
PinP oint-E E DGE/GPR S - User Guide, versi on 2.32 44 Global Positioning System (GPS) The RAP messages are in Hex and ar e referred to by thei r message ID.
PinP oint-E E DGE/GPR S - User Guide, versi on 2.32 45 Global Positioning System (GPS) W ith the device ID enabled, the PinPoint -E will use the value configured for NETPHONE unless NETPHONE is empty in which case th e ESN of the modem will be used.
PinP oint-E E DGE/GPR S - User Guide, versi on 2.32 46 Global Positioning System (GPS) COM1000 Event Reports FIGURE 17. Wireless Ace: COM1000 Events - *PPCOM1000 Store and Forward for RAP Store and Forward RAP can provide seamless coverage even in areas w ith intermittent cellular coverage.
PinP oint-E E DGE/GPR S - User Guide, versi on 2.32 47 Global Positioning System (GPS) S tore and Forward Reliabl e Mode The Store and Forward Reliable Mode allows the PinPoint-E to ensure all message.
PinP oint-E E DGE/GPR S - User Guide, versi on 2.32 48 Global Positioning System (GPS) FIGURE 21. Wireless Ace: Automatic Reports *PP TIME - Location report sent ever y set time interval (seconds).
PinP oint-E E DGE/GPR S - User Guide, versi on 2.32 49 Global Positioning System (GPS) FIGURE 23. HyperT erminal: NMEA S tre am FIGURE 24. Wireless Ace: NMEA S t rings NMEA Messages Over -The-Air (Remote) T o config ure th e PinPoi nt-E to send NMEA reports to a remote server , you will need to set 3 com - mands: *PPIP , *PPPOR T , and *PPGPSR.
PinP oint-E E DGE/GPR S - User Guide, versi on 2.32 50 Global Positioning System (GPS) FIGURE 26. Wireless Ace: NMEA Local Reports 1. Set the port (S53) to the local port to which you want the reports sent. The local IP will aut o - matically be used.
PinP oint-E E DGE/GPR S - User Guide, versi on 2.32 51 Global Positioning System (GPS) T AIP Messages over a Local Connection (PPP) FIGURE 28. Wireless Ace: T AIP Local Reports 1. Set the IP (*PPIP) to the local IP of the PinPoint-E (if you are receiving reports using PPP , you do not need to set *PPIP).
PinP oint-E E DGE/GPR S - User Guide, versi on 2.32 52 Global Positioning System (GPS) 1. Set the port (S53) to 1000 . The local IP will automatically be used. S53, in W ireless Ace, is part of the Misc menu optio n. 2. Set A TS Local Report T ype (*PPLA TSR) to F0 - T AIP Data .
PinP oint-E E DGE/GPR S - User Guide, versi on 2.32 53 Global Positioning System (GPS) FPV configures periodic reporting of PV (Position/V elocity) repo rts. The time interval from the message is stored at *PP TIME. Cu rrentl y the epoch value is ignored.
PinP oint-E E DGE/GPR S - User Guide, versi on 2.32 54 CHAPTER 8 Har dware Installation Y our AirLink PinPoint-E should be mounted in a position that allows easy access for the cables so they are not bent o r constricted. The LED s on the front pan el should be visible for ease of opera - tional verification.
PinP oint-E E DGE/GPR S - User Guide, versi on 2.32 55 Hardwar e Installation Y our PinPoint-E can be used with either DC (a vailable in mo st automobil es) or 1 10 AC (standard US wall power) w ith the ap propriate power adapter (available from AirLink).
PinP oint-E E DGE/GPR S - User Guide, versi on 2.32 56 Hardwar e Installation When your PinPoint-E is connect ed to power and an antenna, there is a specific pattern to the lights to indicate its operation mode.
PinP oint-E E DGE/GPR S - User Guide, versi on 2.32 57 APPENDIX A Modem Placement When decided on a location to install y our PinPoint-E, make sure the modem will be away from direct exposure to the elements (sun, rain, etc.
PinP oint-E E DGE/GPR S - User Guide, versi on 2.32 58 Modem Placement FIGURE 2. PinPoint-E Mounting Bracket, part number 100-170- 1005.
PinP oint-E E DGE/GPR S - User Guide, versi on 2.32 59 Modem Placement GPS Antenna Location There are three options for an antenna: • magnetic roof-mount • through glass-mount • permanent mount Mount the GPS Antenna in the vehi cle. The less the cable is wra pped and bound together, the bet - ter it will perform.
PinP oint-E E DGE/GPR S - User Guide, versi on 2.32 60 APPENDIX B Specifications for the PinPoint-E EDGE/ GPRS Environmental: Physical Characteristics: • W eight: 2 lb s • Size: 6.
PinP oint-E E DGE/GPR S - User Guide, versi on 2.32 61 Specifications for the PinPoint-E EDGE/GPRS Power Management: • Low power consumption • Dormant connection (idle for 10-20 seconds): 60 mA at.
PinP oint-E E DGE/GPR S - User Guide, versi on 2.32 62 APPENDIX B A T Commands Using Wireless Ace W ith Wireless Ace, you only need to find the command listed and then enter th e new value in the space provided. For those commands which have speci fic parameters, the choices will be in a drop down menu.
PinP oint-E E DGE/GPR S - User Guide, versi on 2.32 63 A T Commands FIGURE 2. Wireless Ace: T ool bar For more information on using W ireless Ace, please refer to the W ireless Ace User Guide .
PinP oint-E E DGE/GPR S - User Guide, versi on 2.32 64 A T Commands FIGURE 4. AceNet: Load a T emplate Using T elnet T erminal Emulation It is possible to comm unicate with the PinPoint-E across a TCP/IP network . T elnet provides a termi - nal style connection to the PinPoint-E.
PinP oint-E E DGE/GPR S - User Guide, versi on 2.32 65 A T Commands FIGURE 6. HyperT erminal: TCP/IP Settings 3. When HyperT erminal connects to the PinPoint-E, yo u will be prompted for a password. The default password is 123 45 . When you press Ente r , you sh ould get back a reply of “OK”.
PinP oint-E E DGE/GPR S - User Guide, versi on 2.32 66 A T Commands FIGURE 8. HyperT erminal: Connection Name 2. Select COM1 (or the comport to wh ich the modem is connected) for the Connect Using .
PinP oint-E E DGE/GPR S - User Guide, versi on 2.32 67 A T Commands • Required variable parameters are de noted with italicized text, example, D n . The n is variable and noted in the parameters colu mn . • Optional parameters are denoted with square brackets [ ] .
PinPoint-E EDGE/GPRS - User Guide, version 2.32 68 A T Commands A T Command Listing Symbols #IG . . . . . . . . . . . 110 #U . . . . . . . . . . . . 115 &C . . . . . . . . . . . . . 84 &D . . . . . . . . . . . . . 84 &S . . . . . . . . . .
PinPoint-E EDGE/GPRS - User Guide, version 2.32 69 Commands Index S50 . . . . . . . . . . . . . 83 S51 . . . . . . . . . . . . . 83 S53 . . . . . . . . . . . . . 76 S6 . . . . . . . . . . . . . 82 S60 . . . . . . . . . . . . . 86 S7 . . . . . . . . . .
PinP oint-E E DGE/GPR S - User Guide, versi on 2.32 70 A T Commands: Information and Status Most of the commands in the “Info” and “S tatus” gro ups as well as ot her group s have read-only parameters.
PinPoint-E EDGE/GPRS - User Guide, version 2.32 71 A T Commands: Information and Status I[ n ] *DEVICEID? *ETHMAC? FIGURE 2. St a t u s G r o u p n= 0 Product name (for example, PinPoint-E Raven-E) . n= 1 The PinPoint-E’ s firmware (ALEOS) version, hard ware ID, and copyright.
PinPoint-E EDGE/GPRS - User Guide, version 2.32 72 A T Commands: Information and Status *HOSTMODE? *NETOP? *NETPHONE? *NETRSSI? *NETSERV? *NETSTATE? The current host mode (A T , PPP , UDP , etc.). If the PinPoi nt-E is not in A T mode, telnet into t he modem to execute this command.
PinPoint-E EDGE/GPRS - User Guide, version 2.32 73 A T Commands: Information and Status *POWERMODE? &V +CCID +CIMI • Network Negotiation Fail Network connection negotiation failed. This is usually temporary and often clears up dur - ing a subsequent attempt .
PinPoint-E EDGE/GPRS - User Guide, version 2.32 74 A T Commands: Information and Status +HWTEMP? +ICCID +RCIQ Displays the internal temperature of the radio module in degrees Centigrade.
PinPoint-E EDGE/GPRS - User Guide, version 2.32 75 A T Commands: Information and Status FIGURE 4. Map V iew Note: The map feature will only work if you have access to the Internet on your computer either through the mo dem or sep e rate from the mo dem.
PinP oint-E E DGE/GPR S - User Guide, versi on 2.32 76 A T Commands: Misc (Miscellaneous) This group includes configuration commands which are not specific to oth er gro ups. OPRG= n S53= [method][d.d.d.d][/ ppppp] Misc (Miscellaneous) The commands displayed in W ireless Ace and th e results of those commands depends on the model of the modem.
PinPoint-E EDGE/GPRS - User Guide, version 2.32 77 A T Commands: Misc (Miscellaneous) *DPORT= n *HOSTPA P= n *NETALLOWZEROIP= n *NETPW= pw *NETPHONE? Examples: A TS53=T1 92.168.100.23/12345 A TS53=foo.earlink.com T eln et to the specified IP at port 1234 5.
PinPoint-E EDGE/GPRS - User Guide, version 2.32 78 A T Commands: Misc (Miscellaneous) *NETUID= uid *STATICIP= d.d.d.d The login that is used to login to Y our W ireless Service Provider’ s cellular network , when required. uid =user id (up to 64 bytes) Set the static IP required to be received from the network.
PinP oint-E E DGE/GPR S - User Guide, versi on 2.32 79 A T Commands: Serial This group includes commands specific to the serial port. +++ Serial The commands displayed in W ireless Ace and th e results of those commands depends on the model of the modem.
PinPoint-E EDGE/GPRS - User Guide, version 2.32 80 A T Commands: Serial A/ A D [method][d.d.d.d][/ppppp] or D [method][@name][/ppppp] Note: This command is not proceed ed by A T . Re-execute last command. Cannot be configur ed in W ireless Ace. Manually answer an incoming connection.
PinPoint-E EDGE/GPRS - User Guide, version 2.32 81 A T Commands: Serial DS= n E n H n Q n S3= n S4= n Allows a PPP connection to be initiated on the host port. n= 2 : Initiates the PPP connection. Cannot be configur ed in W ireless Ace. T oggle A T command echo mode.
PinPoint-E EDGE/GPRS - User Guide, version 2.32 82 A T Commands: Serial S5= n S6= n S8= n S9= n S10= n S23= [speed],[databits][parity][stop bi ts] Backspace Character n= 0-127 (ASCII character number ) This register sets the ch aracter recognized as a b acks pace during command entry .
PinPoint-E EDGE/GPRS - User Guide, version 2.32 83 A T Commands: Serial S50= n S51= n S211= n V n X n speed =300 | 1200 | 2400 | 4800 | 9600 | 19200 | 38400 | 576 00 | 115200 | 230400 databits = 7 or 8 parity = O : Odd parity = E : Even parity = N : None parity = M: Mark stopbits =1 | 1.
PinPoint-E EDGE/GPRS - User Guide, version 2.32 84 A T Commands: Serial Z &C n &D n &S n &W APPP ASLIP n= 1 : T urn on result codes. This adds th e text 19200 to the CONNECT response. Reset the PinPoint-E. In W ir eless Ace, this command is performed with the Reset option on the toolbar .
PinPoint-E EDGE/GPRS - User Guide, version 2.32 85 A T Commands: Serial Q *CTSE= n *MODEMHISPEED *NUMTOIP= n Cannot be configur ed in W ireless Ace. Set or query the serial port flow control setting. n= 0 : No flow control is bein g used. n= 1 : R TS/CTS hardware flow control is being used.
PinP oint-E E DGE/GPR S - User Guide, versi on 2.32 86 A T Commands: TCP This group includes commands specific to TCP communications. FIGURE 1. Common : TCP S0= n S7= n S60= n TCP Note: Data from the cellu lar network (and the Internet) is only sent to the Ethern et port.
PinPoint-E EDGE/GPRS - User Guide, version 2.32 87 A T Commands: TCP S221= n TCPS= n TCPT= n *ENQ= n Connect Delay: n= 0 - 255 Number of seconds to delay the “CONNECT' response upon establishi ng a TCP connection .
PinP oint-E E DGE/GPR S - User Guide, versi on 2.32 88 A T Commands: UDP This group includes commands specific to UDP communications. FIGURE 1. Common : UDP AIP= n HOR= n MD hh UDP Note: Data from the cellu lar network (and the Internet) is only sent to the Ethern et port.
PinPoint-E EDGE/GPRS - User Guide, version 2.32 89 A T Commands: UDP S82= n S83= n *DU= n *UALL= n When the PinPoint-E is power -cy cled, the serial port enters the mode specified by this com - mand after 5 seconds. On startup, typing A TMD0 with in 5 seconds changes the mode to nor - mal (A T command) mode.
PinPoint-E EDGE/GPRS - User Guide, version 2.32 90 A T Commands: UDP *UDPLAST= n *USD= n n= 0 : No effect (Defaul t). n= 1 : Accept UDP data from all IP addr esses when in a UDP session. If enabled, sets S53 to the last accepted IP address through UDP auto answer .
PinP oint-E E DGE/GPR S - User Guide, versi on 2.32 91 A T Commands: DNS This group includes commands specific to the modem bein g able to use domain names instead of IP addresses for other configuration options. FIGURE 1. Common : DNS *DNS n *DNSUPDATE= n *DNSUSER= d.
PinP oint-E E DGE/GPR S - User Guide, versi on 2.32 92 A T Commands: Dynamic IP This group includes commands specific to dynam ic DNS. Dynamic DNS allo ws the PinPoint-E to use a dynamic IP (can chang.
PinPoint-E EDGE/GPRS - User Guide, version 2.32 93 A T Commands: Dynamic IP *IPMGRKEY n = [key] *IPMGRUPDATE n = m *MODEMNAME = [name] Sets the 128-bit key to use to authenticate the IP update notifications. If the key's value is all zeros, a default key will be used.
PinP oint-E E DGE/GPR S - User Guide, versi on 2.32 94 A T Commands: PPP/Ethernet This group includes commands specific to PPP or Ethernet connections between the PinPoint-E and a connected device. *HOSTAU TH= n *HOSTNETMASK= n.n.n.n *HOSTPEERIP= d.d.
PinPoint-E EDGE/GPRS - User Guide, version 2.32 95 A T Commands: PPP/Ethernet *HOSTPRIVIP = d.d.d.d *HOSTPRIVMODE= n *HOSTPW= string *HOSTUI D= string Set or query the private IP addr ess that is to be negotiated b y the EDGE/GPRS connection if *HOSTPRIVMODE =1 .
PinP oint-E E DGE/GPR S - User Guide, versi on 2.32 96 A T Commands: PassThru PassThru Mode is used to communicate direct ly to the PinPoint-E’ s internal hardware. FIGURE 1. Common : PassThru *CSX1= n *PTINIT= string *PTREFRESH = n *RESETPERIOD= n PassThru Caution: While the modem is in PassThr u mode, ALEOS is disabl ed.
PinPoint-E EDGE/GPRS - User Guide, version 2.32 97 A T Commands: PassThru APASSTHRU Caution: This mode is not available through the remo te A T telnet server . Y ou will need to connect to the PinPoint-E with it connected dire ctly to your computer . Sets the modem operation to pass through mode.
PinP oint-E E DGE/GPR S - User Guide, versi on 2.32 98 A T Commands: SMTP (including SMS) This group includes commands specific to messaging. FIGURE 1. Common : SMTP SMTP (including SMS) SMTP (Simple Mail Transfer Protocol) is the de facto standard for email transmission across the Internet.
PinPoint-E EDGE/GPRS - User Guide, version 2.32 99 A T Commands: SMTP (including SMS) *SMTPSTATU S? Note: Not required to use SMTP sett ings but may be required by Y our W ireless Service Provider.
PinP oint-E E DGE/GPR S - User Guide, versi on 2.32 100 A T Commands: Other The commands in this group are not sp ecific to the other group categories. FIGURE 1. Common : Other DAE= n *DATZ= n *IPPING= n Other The commands displayed in W ireless Ace and th e results of those commands depends on the model of the modem.
PinPoint-E EDGE/GPRS - User Guide, version 2.32 101 A T Commands: Other *IPPINGADDR= [d.d.d.d][name] *MSCIUPDAD DR= name[/port] *MSCIUPDPER IOD= n *NETWDOG= n *SNMPCOMMUNITY= n *SNMPPORT= n *SNMPSECLVL= n n= 15-255 minutes n= 0 : Disable pinging (default) 15 minutes is the minimum interv al which can be set for Keepalive.
PinPoint-E EDGE/GPRS - User Guide, version 2.32 102 A T Commands: Other *SNMPTRAPDEST= host/[port] *SNTP= n *SNTPADDR= [d.d.d.d][name] *TELNETTIMEOUT= n *TPORT= n n= 0 : No security required. SNMPv2c and SNMPv3 communications are allowed. n= 1 : Authentication equivalent to “aut hNo Priv” setting in SNMPv3.
PinP oint-E E DGE/GPR S - User Guide, versi on 2.32 103 A T Commands: Low Power The PinPoint-E will put itsel f into a low power using mode when conf igured events occur (page 32). Low Power mode is essentially a standby m ode which uses minimal power while being ready to “come alive” quickly .
PinPoint-E EDGE/GPRS - User Guide, version 2.32 104 A T Commands: Low Power Power related commands in other command groups *POWERMODE? FIGURE 2. S tatus : *POWERMODE? In the St a t u s grou p, *PO WERMODE displ ays the current power state/mode.
PinP oint-E E DGE/GPR S - User Guide, versi on 2.32 105 A T Commands: Friends Friends Mode can limit access to the PinPoint-E from Y our W ireless Se rvice Provider’ s network and the Internet. Friends Mode is a basic firewall. FIGURE 1. Common : Friend s FM= n Fn= [d.
PinPoint-E EDGE/GPRS - User Guide, version 2.32 106 A T Commands: Friends 255 = allow any number 0-255 Example: 166.129.2.255 allows access by al l IPs in the range 166.
PinP oint-E E DGE/GPR S - User Guide, versi on 2.32 107 A T Commands: Logging This group includes commands sp ecific to the internal log. *DBGCOMMLVL= n *DBGDHCPLVL= n *DBGETHLVL= n *DBGIPLVL= n *DBGPPPLVL= n Logging Caution: Logging is intended for diagnostic purposes only .
PinPoint-E EDGE/GPRS - User Guide, version 2.32 108 A T Commands: Logging n= 0 : No logging n= 1 : Log client events (default ) n= 2 : Log server events n= 3 : Log client and Server events.
PinP oint-E E DGE/GPR S - User Guide, versi on 2.32 109 A T Commands: PinPoint This group includes commands speci fic to the PinPoint-E and GPS. FIGURE 1. PinPoint DTRI= n RTSI= n PinPoint This screen shot does not show all th e commands on the Wireless Ace PinPoint menu, scroll down in W ireless Ace for the rest of the PinPoint command s.
PinPoint-E EDGE/GPRS - User Guide, version 2.32 110 A T Commands: PinPoint #IG= n *MF= hh *PGPS= n *PPCOM10 00= n *PPDEVID= n *PPDIST= n Note: If R TS is used as an input, hardware flow control cannot be enabled. Set or query GPS initialization timer .
PinPoint-E EDGE/GPRS - User Guide, version 2.32 111 A T Commands: PinPoint *PPFLUSHONEV T= n *PPGPSDATUM= n *PPGPSSENTENCES = n *PPGPSR= n *PPIGNOREIP= n *PPINPUTEVT= n Flushes store and forward buffer when an input eve nt (DTR/R TS) occurs. n= 0 : Disable n= 1 : Enable Specifies the GPS datum to use for position reports.
PinPoint-E EDGE/GPRS - User Guide, version 2.32 112 A T Commands: PinPoint *PPIP= d.d.d.d *PPLATS= n *PPLATSEXTR A= n *PPLATSR= n *PPMINTIME= n IP address where GPS reports are sent (A TS Server IP). Also see *PPPORT . d.d.d.d =IP address Example: A T*PPIP=1 92.
PinPoint-E EDGE/GPRS - User Guide, version 2.32 113 A T Commands: PinPoint *PPODOM= n *PPODOMVAL= n *PPPORT= n *PPSNF= n *PPSNFB= n *PPSNFM= n *PPSNFR= n Enable odometer reporting. n= 0 : Disabled (default) n= 1 : Enabled The PinPoint-E’ s current odometer value.
PinPoint-E EDGE/GPRS - User Guide, version 2.32 114 A T Commands: PinPoint *PPTAIPID= nnnn *PPTIME= n *PPTSV= n *UDPRGPS= n n= 1 : Reliable mode enab led for RAP messages GPS reports will be retransmitted if not acknowledged by the server . Sets/queries the T AIP ID.
PinPoint-E EDGE/GPRS - User Guide, version 2.32 115 A T Commands: PinPoint GPS n #U PinPoint related A T Commands no t A vailable through W irele ss Ace Send NMEA GPS strings out serial link. See also *PGPS . AT G P S (no parameter) will cause the NMEA GGA, RM C, and VTG GPS strings to output to the serial port one time.
PinP oint-E E DGE/GPR S - User Guide, versi on 2.32 116 A T Commands: EDGE/HSDP A FIGURE 1. EDGE/HSDP A *NETAPN= apn +CGQMIN +CGQREQ +COPS= mode , [format][,oper] EDGE/HSDP A This group includes commands specific to EDGE and GPRS. The commands displayed in W ireless Ace and th e results of those commands depends on the model of the modem.
PinP oint-E E DGE/GPR S - User Guide, versi on 2.32 117 APPENDIX C PPPoE: Point to Point Pr otocol over Ether net PPPoE (Point-to-Point Protocol over Et hern et) allows a point-to-point connection wh ile using Ethernet.
PinP oint-E E DGE/GPR S - User Guide, versi on 2.32 118 PPPoE: Point to Point Protocol over Ethernet FIGURE 1. Wireless Ace: Connect b. When W ireless Ace has connected to you r PinPoint-E, from the groups on the left, select PPP/ Ethernet under Common .
PinP oint-E E DGE/GPR S - User Guide, versi on 2.32 119 PPPoE: Point to Point Protocol over Ethernet PPPoE connections can use a Service Name to di fferentiate PPPoE devices. Y ou can use Wi reless Ace to give your PinPoint-E a name. a. In W i reless Ace, select Dynamic IP from the groups on the left .
PinP oint-E E DGE/GPR S - User Guide, versi on 2.32 120 PPPoE: Point to Point Protocol over Ethernet Configuring a PPPoE Connection in Windows a. Select S tart > Connect T o > Show All Connections . This will open the Network Connec - tions window .
PinP oint-E E DGE/GPR S - User Guide, versi on 2.32 121 PPPoE: Point to Point Protocol over Ethernet FIGURE 8. New Connection c. Select Connect to the Internet and then select Next . FIGURE 9. Connection T ype d. Select Set up my connection manually and then select Next .
PinP oint-E E DGE/GPR S - User Guide, versi on 2.32 122 PPPoE: Point to Point Protocol over Ethernet FIGURE 1 1. Internet Connection f. T ype in a name for the connection, such as AirLink PPPoE Connection .
PinP oint-E E DGE/GPR S - User Guide, versi on 2.32 123 PPPoE: Point to Point Protocol over Ethernet h. If you want to add a shortcut for this connection to your desktop , check Add a shortcut... Select Finish to exit the Network Connection W izard . FIGURE 14.
PinP oint-E E DGE/GPR S - User Guide, versi on 2.32 124 PPPoE: Point to Point Protocol over Ethernet FIGURE 15. Connect a. When the Connect window opens, select Properties . Optional: On the General tab, if you gave the modem a name with *M ODEMNAME above, you can type in that name as the Service Name .
PinP oint-E E DGE/GPR S - User Guide, versi on 2.32 125 PPPoE: Point to Point Protocol over Ethernet Optional: Y ou may want to check the Options tab and change the settings for applicat ions you might be using. The default options are g enerally applicable for m ost uses.
PinP oint-E E DGE/GPR S - User Guide, versi on 2.32 126 PPPoE: Point to Point Protocol over Ethernet Configuring your router for PPPoE with the PinPoint-E If your network router has PPPoE discovery , the PinPoint-E will be discovered on the intranet through PPPoE discovery process, which uses broadcast Ethernet packets.
PinP oint-E E DGE/GPR S - User Guide, versi on 2.32 127 APPENDIX D Simple Network Management Pr otocol (SNMP) The PinPoint-E can be configured as an SN MP agen t and supports SNMPv2c and SNMPv3.
PinP oint-E E DGE/GPR S - User Guide, versi on 2.32 128 Simple Network Management Protocol (SNMP) There are only three comm ands to set for SNMP in the PinPoint-E: the li st ening port, the security level, and the trap destination. Listening Port *SNMPPOR T sets the port for the SNMP agen t to li sten on.
PinP oint-E E DGE/GPR S - User Guide, versi on 2.32 129 Simple Network Management Protocol (SNMP) FIGURE 3. Wireless Ace: Changing the PinPoint-E Password - Menu Option The current password will be pre-entered. As you type the new password and confirm it, the char - acters you type will be obscured by “x”.
PinP oint-E E DGE/GPR S - User Guide, versi on 2.32 130 Simple Network Management Protocol (SNMP) IMPOR TS ObjectName FROM SNMPv2-SMI MODULE-COMPLIANCE FROM SNMPv2-CONF; org OBJECT IDENTIFIER ::= { is.
PinP oint-E E DGE/GPR S - User Guide, versi on 2.32 131 Simple Network Management Protocol (SNMP) modemT ype OBJECT -TYPE SYNT AX DisplayString MAX-ACCESS read-only ST A TUS current ::= { general 4 } .
PinP oint-E E DGE/GPR S - User Guide, versi on 2.32 132 Simple Network Management Protocol (SNMP) otaProgrammingEna ble OBJECT -TYPE SYNT AX INTEGER { disabled(0), enabled(1) } MAX-ACCESS read-only ST A TUS current ::= { common 2 } devicePort OBJECT -TYPE SYNT AX INTEGER(0.
PinP oint-E E DGE/GPR S - User Guide, versi on 2.32 133 Simple Network Management Protocol (SNMP) SYNT AX DisplayString MAX-ACCESS read-only ST A TUS current ::= { common 7 } destinationPor t OBJECT -TYPE SYNT AX INTEGER(0.
PinP oint-E E DGE/GPR S - User Guide, versi on 2.32 134 Simple Network Management Protocol (SNMP) ST A TUS current ::= { status 2 } netChannel OBJECT -TYPE SYNT AX INTEGER MAX-ACCESS read-only ST A TUS current ::= { status 3 } rssi OBJECT -TYPE SYNT AX INTEGER(-125.
PinP oint-E E DGE/GPR S - User Guide, versi on 2.32 135 Simple Network Management Protocol (SNMP) ST A TUS current ::= { status 8 } fixObtained OBJECT -TYPE SYNT AX INTEGER { no(0), yes(1) } MAX-ACCES.
PinP oint-E E DGE/GPR S - User Guide, versi on 2.32 136 APPENDIX E GPS Message Format Str eams This appendix shows the GPS message streams provi ded by the PinPoint-E.
PinP oint-E E DGE/GPR S - User Guide, versi on 2.32 137 GPS Message Format Streams Example taken from PinPoint-E output: $GPRMC,173219.428,A,35 05.1436,N,0 8037.5669,W ,0.09,13.55,040403,,,*2B Example taken from PinPoint-E output: $GPVTG , 308.49,T ,,M,0.
PinP oint-E E DGE/GPR S - User Guide, versi on 2.32 138 GPS Message Format Streams T AIP Message Description The T AIP data stream provided by the modem wil l be raw serial (ASCII) format and is always uppercase.
PinP oint-E E DGE/GPR S - User Guide, versi on 2.32 139 APPENDIX F W arranty T erms and Conditions The following terms and conditions ("W arranty T e rm s") govern the warrant y servi ces offered to you ("Customer") by AIRLINK CO MMUNICA TION S, INC.
PinP oint-E E DGE/GPR S - User Guide, versi on 2.32 140 W arranty T erms and Conditions Warranty Conditions Remedy If under normal use the Software and/or Hardware (collectively , the "Pro ducts&.
PinP oint-E E DGE/GPR S - User Guide, versi on 2.32 141 W arranty T erms and Conditions DIRECTL Y GIVES RISE TO THE CLAIM. THIS CLAUSE WI LL SUR VIVE THE F AILURE OF ANY EXCLUSIVE REMEDY AND THE EXPIRA TION OF THESE W ARRANTY TERMS.
PinP oint-E E DGE/GPR S - User Guide, versi on 2.32 142 APPENDIX G Fr equently Asked Questions and T echnical Support Many of these questions and solutions in the following sections come from AirLin k Support. FA Q T o p i c s Power, Antennas , an d Signal Strengt h .
PinP oint-E E DGE/GPR S - User Guide, versi on 2.32 143 Frequently Asked Questions and T echnical Support Power , Antennas, and Signal S trength RSSI (Received Signal Strength In dication) is a measurement of the strength or intensity , not nec - essarily the quality , of the received signal.
PinP oint-E E DGE/GPR S - User Guide, versi on 2.32 144 Frequently Asked Questions and T echnical Support Dipole Dipole is a common antenna type connecti ng directly to the PinPoint-E and extending out in a sin - gle straight wire.
PinP oint-E E DGE/GPR S - User Guide, versi on 2.32 145 Frequently Asked Questions and T echnical Support The PinPoint-E’ s IP Addresses and Local Networking On Y our W ireless Service Provider’ s.
PinP oint-E E DGE/GPR S - User Guide, versi on 2.32 146 Frequently Asked Questions and T echnical Support Note: *HOSTPRIVMODE works the same for both Ethern et using DHCP or serial using PPP .
PinP oint-E E DGE/GPR S - User Guide, versi on 2.32 147 Frequently Asked Questions and T echnical Support In W ireless Ace, *DHCPSERVER is part of the PPP/Ethernet group.
PinP oint-E E DGE/GPR S - User Guide, versi on 2.32 148 Frequently Asked Questions and T echnical Support Security for the PinPoint-E For specific information about the security of Y our W ireless Service Provider’ s network, co ntact your cellular deal er directly .
PinP oint-E E DGE/GPR S - User Guide, versi on 2.32 149 Frequently Asked Questions and T echnical Support GPS Featur es The vehicle speed is based on th e accuracy of each GPS recorded point which can be off by 10 meters in any direction. What you want to look for is a trend.
PinP oint-E E DGE/GPR S - User Guide, versi on 2.32 150 Frequently Asked Questions and T echnical Support speed reading, then this may point to an inaccurate sp eed reading. Otherwis e, if you see consistent acceleration and deceleratio n, it's probably accurate.
PinP oint-E E DGE/GPR S - User Guide, versi on 2.32 151 AirLink T echnical Support If you encounter problems with operation of yo ur PinPoint-E, AirLink’ s support staff can help. AirLink Support W eb Site The AirLink web site is updated frequently with Setup Wizards, Utilities, How-T o Guides, and other documentatio n: ht tp://www .
デバイスAirlink EDGE/GPRSの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Airlink EDGE/GPRSをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはAirlink EDGE/GPRSの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Airlink EDGE/GPRSの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Airlink EDGE/GPRSで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Airlink EDGE/GPRSを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はAirlink EDGE/GPRSの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Airlink EDGE/GPRSに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちAirlink EDGE/GPRSデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。