Airlink101メーカーAPSUSB211の使用説明書/サービス説明書
ページ先へ移動 of 33
1-Port USB 2.0 Print Server Model # APSUSB211 User’s Manual Ver. 1B.
1 Table of Contents 1 Introduction ............................................................................................... 2 1.1 Package Contents ............................................................................... 2 1.2 System Requirements .
2 1 Introduction Congratulations on purchasing your 1-Port U SB 2.0 Print Server. It is the easiest and fastest way to deploy printers on your network. This compact Print Server uses your network router to connect various computers and printer together.
3 2 Hardware Inst allation 2.1 Connecting the Print Server Warning: Only a USB printer may be connected to the USB port of the Print Server. Connecting any other USB devic e to the Print Server may damage the Print Server. Do not plug the power cord to the Pr int Server until you have reached Step 4 of this section.
4 3. Inst alling PS Utility Step 1 Insert the provided CD and wait for the autorun screen to appear. Step 2 Click on Install PS Utility . Note: If the autorun screen does not appear automatically, go to Start , Run , type D:autorun.exe (where D is the letter of your CD drive) and click OK .
5 Step 4 Click Next . Step 5 Click Yes . Step 6 Click Finish ..
6 4. Configuring Network Setting Before configuring the Print Server’s network setting, please take note of your computer’s TCP/IP setting. Step 1 Click on Start , Run , and type command (for Windows 95/98/ME) or cmd (for Windows 2000/XP) and click OK .
7 Step 6 In the IP Address field, enter a valid IP address, subnet mask, and default gateway that matches your local area network. For example : If your computer’s IP Address is 192.168.1 .100 , enter the same three numbers: 192.168.1 in the corresponding fields.
8 5. V erifying Network Connection Step 1 Run the PS Utility by going to Start , (All) Progra ms , PS-Utility , PS-Utility v3.00 . Step 2 Make sure the Print Server is detected under the Device Name . Step 3 Click on Show Web Setup to display the Print Server’s Web Configuration Utility .
9 Step 5 Click on the Print Test link and click the Test button. The Print Server will perform a low-level print test, bypa ssing the operating system layer. Note: Your printer should print out a test page. If not, verify that the printer is powered on and all cables are securely connected and tr y again.
10 6. Running PS Wizard Warning: Make sure you have installed the printer driver locally on every computer that will use the print server in your networ k before running the PS Wizard. Otherwise, the PS Wizard will not run properly. Be sure to run the PS Wizard on a ll the computers that will use the print server in your network.
11 Step 3 Click Next . Step 4 Select the printer that is connec ted to the Print Server and click Next ..
12 Step 5 Double-click on the Print Server Name , select the Printer Port Name , and click Next . Step 6 Click Finish and OK . (For Windows 95/98/ME, you’ll need to reboot the computer). Step 7 Run the PS Wizard on all the computers in your network that will use the Print Server.
13 7. Performing Operating System Print T est The final step in setting up the Print Server is to perform an operating system print test. Please note that the instructions below are for Windows XP, but the steps are similar for all the other Windows operating systems.
14 Step 3 Click on the Print Test Page button. Windows should print out a test page. You have successfully configured the Print Server for printing..
15 8. Using the PS Utility PS Utility is a user-friendly program that allows you to configure some basic functions of the Print Server such as performing a factory reset or updating the firmware.
16 9. Using the W eb Configuration Utility The Web Configuration Utility allows you to manage the fu ll features of the Print Server with an easy-to-use user interface. You can start the Web Configuration Utility in two ways: 1. Click on the Show Web Setup button in PS Utility .
17 9.1 Home The Home page displays the status of your Print Server. Click Refresh to update the page..
18 9.2 Setup Wizard The Setup Wizard page allows you to configure some basic settings of the Print Server, including specifying an optional password to l og in to the Web Config uration Utility. This page is optional unless you want to se tup a password for the Print Server.
19 IP Address : Select to Manually Assign an IP Address for the Print Server (recommended) or have the router Automatically Assign an IP Address. Click Next to proceed.
20 Workgroup : Enter the name of your Microsoft Network. Click Next to proceed..
21 Second HTTP Port : Select to Enable or Disable a second HTTP port for Remote Web Configuration and IPP Printing. Port Number : You may enter the desired port num ber for the second HTTP port.
22 Click Yes to save the settings, No to cancel the settings. Note : you may need to re-run the PS Wizard to update these changes..
23 9.3 Change IP Address The Change IP Address page allows you to manually assign an IP Address for the Print Server. The IP Address must be on the same subnet as your network. Click Save to save and activate any configuration changes. Click Cancel to cancel the changes.
24 9.4 Printer Information The Printer Information page shows the status of your printer. Click Refresh to update the page..
25 9.5 Print Test The Print Test page allows you to perform a print test. Click on the Test button to begin the print test. Your printer should print out a test page. If not, verify that the printer is powered on and all cables are securely connected and try again.
26 9.6 Factory Reset The Factory Reset page allows you to reset the Prin t Server to the default factory settings. Click Yes to reset all the settings to factory default.
27 9.7 Firmware Upgrade When a new version of the firmware is available on our web site, www.airlink101.com , you can download the new firmware and pr oceed to the followin g page to upgrade the firmware. 1. Click Browse and browse to the location of the downloaded firmware.
28 9.8 About The About page displays the Print Server’s firmware version number..
29 10. Printing in Mac OS This section describes how to set up your Ma c OS settings to work with the Print Server. 10.1 Using Rendezvous Mac OS X provides a new feature called Rendezvous .
30 Step 2 Select Rendezvous from the pop-up menu. Step 3 A list of Rendezvous-enabled printers will appe ar in the list..
31 Step 4 Choose the desired printer and select Generic . Step 5 The printer is installed into the system successfully..
32 1 1. Appendix Technical Support E-mail: support@airlink101.com Toll Free: 1-888-746-3238 Web site: www.airlink101.com Copyright © 2005 AirLink101. All rights reserved.
デバイスAirlink101 APSUSB211の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Airlink101 APSUSB211をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはAirlink101 APSUSB211の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Airlink101 APSUSB211の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Airlink101 APSUSB211で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Airlink101 APSUSB211を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はAirlink101 APSUSB211の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Airlink101 APSUSB211に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちAirlink101 APSUSB211デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。