Airlink101メーカーAWLC4030の使用説明書/サービス説明書
ページ先へ移動 of 30
Super G™ Cardbus Adapter Model # AWLC4030 User’s Manual Ver. 2B.
2 Table of Contents 1. Introduction ................................................................................................................................. 3 1.1 Package Contents ..............................................................
3 1. Introduction Thank you for purchasing the Super G™ Cardbus Adapter. When used with other Airlink101™ Super G™ wireless products, the wireless data throughput increases compared to the standard 802.11g products. This Adapter supports 64/128-bit WEP data enc ryption that protects your wireless network from eavesdropping.
4 2. Inst allation 2.1 Install Driver & Utility This section provides instructions on how to install the Super G™ Cardbus Adapter . The driver is install ed along with the utility. Note: Do not insert the Cardbus Adapter until you have reached the appointed step.
5 Step 2 Click Next at the welcome screen. Step 3 Click Next to accept the default destination folder..
6 Step 4 Click Continue Anyway at the Windows Logo Screen. (For Windows 2000, click Yes at the Digital Signatur e Not Found prompt). Step 5 Verify Yes, I want to restart my computer now is selected and click Finish to restart your computer.
7 Step 6 After your computer is restar ted, insert the Cardbus Adapter. Step 7 Select Install the software automatically and click Next . For Windows 98SE and ME, select Search for the best dr iver for your device and click Next . Verify all the check boxes are checked and click Next .
8 Step 8 Click Continue Anyway at the Windows Logo Screen. (For Windows 2000, click Yes at the Digital Signatur e Not Found prompt). Step 9 Click Finish .
9 2.2 Verify Driver Installation To verify if the driver has been installed successfully, pl ease perform the following steps. Step 1 Right-click on My C omputer from your desktop and select Properties . Step 2 Select the Device Manager tab. (For Windows 2000/XP, select the Hardware tab first then click on Device Manager ).
10 Step 3 Expand Network adapters from the list and verify that Airlink101 MIMO XR Cardbus Adapter is listed and no yellow question mark is beside it. If Airlink101 Super G Cardbus Adapter is not listed, or y ou see a yellow question mark beside it, please re-install the driver again.
11 3. Configure the Cardbus Adapter This section describes how to connect your Super G™ Cardbus Adapter to a wireless network. Note to Windows XP Users: You must disable the Wireless Zero Configur ation Utility in order to use the bundled Wireless Utility.
12 To open the Cardbus Adapter’s utility go to Start > (All) Program s > Airlink101 Super G Cardbus Utility > Airlink101 Super G Cardbus Utility . Step 1 Go to the AP List tab, select the SSID (Network Name) of the wireless network you wish to connect to, and click Connect .
13 Step 2 If encryption is not enabled for the select ed access point / router, skip to step 6. Otherwise, enter a Profile Name for your wireless setting and click Next . Step 3 Verify that the Network Name matches the SSID of your wireless network and click Next .
14 Step 4 Select the proper encryption setting for your wireless router or access point from the drop-down menu and click Next . Step 5 Follow the on-screen instructions to complete the encryption settings. Click Complete when finished. Step 6 You should see a blue circle around the antenna icon indicating a valid connection.
15 Step 7 Go to the Link Information tab and click on the More button. Step 8 Verify that you are receiving adequate Signal Strength and Link Quality and that you have been assigned a valid IP address (instead of all 0’s).
16 4. Configure the Wireless Utility This section describes the various functi ons of the Wireless Utility that you can configure, including the setti ngs of wireless encryption. 4.1 Link Information The Link Information tab shows the current profile in use as well as details of the current network connection.
17 The Wireless Information displays the current wireless network you are connected to as well as various other statuses such as the Signal Strength and your assigned IP address.
18 4.2 AP List The AP List tab displays all the available Acce ss Points detected by the Cardbus Adapter. Simply select the desired Access Point you wish to connect to and click Connect . The Site Information displays a list of status for the selected AP, including the Channel number and the Encryption status.
19 4.3 Configure Encryption Settings This section describes how to configure encryption settings for the Cardbus Adapter . Note: The encryption settings you set for the A dapter must match t he same settings of the Access Point/Wireless Router; otherwise, the encryption will not work properly.
20 Step 3 Verify the Network Name (SSID) is correct and click Next . For WEP Settings: WEP Step 4 Select the appropriate Authentication Mode and Encryption settings and click Next .
21 WEP Step 5 Select the appropriate Input Method , Key (password), Key Index , and click Next . WEP Step 6 Click Complete to finish the settings..
22 For WPA Settings: WPA Step 4 Select WPA-PSK and the appropriate Input Method and click Next . WPA Step 5 Enter the WPA Key (passphrase) and click Next .
23 WPA Step 6 Click Complete to finish the settings. Step 7 You should see a blue circle around the antenna icon indicating a valid connection. A lock icon beside the antenna indicates the connection is encrypted.
24 4.4 Profile Setting The Profile Setting tab lists all the profiles you have created. You can create new profiles for different network environments.
25 Step 2 Enter a name for your new profile and click Next . Step 3 Enter the SSID (Network Name) of the wireless network you want to connect to and click Next .
26 Step 4 Configure any encryption setting if required and click Next . Step 5 Click Complete to finish the profile setting..
27 Step 6 Your new profile will be listed in the Profile List. Step 7 You can quickly select which prof ile you want to use from the Link Information tab depending on your network environments wit hout having to reconfigure the settings each time.
28 4.5 Static IP Setting To change the IP address of the wireless adapter to Static IP, follow the steps below: Step 1 On the last step of 4.4 Profile Setting , under IP setting, select New Setting and click Next . Step 2 Select Static . Step 3 Enter in the information and click Complete to finish the setting.
29 4.6 About The About tab shows the Utility, Driver, and Firmware version as well as the MAC address of the Super G™ Cardbus Adapter ..
30 T echnical Support E-mail: support@airlink101.com Toll Free: 1-888-746-3238 Web Site: www.airlink101.com *Super G TM technology (108 Mbps) can only be obtained when using products with A theros Super G TM chipset *Theoretical maximum wireless signal rate based on IEEE standard 802.
デバイスAirlink101 AWLC4030の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Airlink101 AWLC4030をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはAirlink101 AWLC4030の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Airlink101 AWLC4030の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Airlink101 AWLC4030で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Airlink101 AWLC4030を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はAirlink101 AWLC4030の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Airlink101 AWLC4030に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちAirlink101 AWLC4030デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。