DeWaltメーカー36-255の使用説明書/サービス説明書
ページ先へ移動 of 21
INSTRUCTION MANUAL 12" Compound Miter Saw (Model 36-255) P ART NO. 899943 - 05-31-01 Copyright © 2001 Delta Machinery ESP AÑOL: PÁGINA 21 T o learn more about DEL T A MACHINER Y visit our website at: www .deltamachinery .com. For Parts, Service, W arranty or other Assistance, please call 1-800-223-7278 ( In Canada call 1-800-463-3582).
2 GENERAL SAFETY RULES W oodworking can be dangerous if safe and pr oper operating procedur es ar e not followed. As with all machinery , certain hazar ds are involved with the operation of the pr oduct. Using the machine with r espect and caution will considerably lessen the possibility of personal injury .
3 ADDITIONAL SAFETY RULES FOR COMPOUND MITER SAWS 1. WARNING: USE ONL Y CROSS-CUTTING SAW BLADES. DO NOT USE BLADES WITH DEEP GULLETS AS THEY CAN DEFLECT AND CONT ACT THE GUARD. 2. WARNING: Do not operate the miter saw until it is completely assembled and installed accor ding to the instructions.
4 4 REPLACEMENT P ARTS When servicing, use only identical replacement parts. POLARIZED PLUGS: T o reduce the risk of electric shock, this equipment has a polarized plug (one blade is wider than the other). This plug will fit in a polarized outlet only one way .
UNP ACKING 1. Carefully r emove the machine fr om the carton. Retain all packing materials until you have inspected and satisfactorily operated the machine. WARNING: Do not connect the machine to the power source until you have r ead and understood this entir e instruction manual.
6 6 MOVING T ABLE TO THE 0 DEGREE CUT -OFF POSITION 1. Rotate locking knob (A) Fig. 6 counter -clockwise as far as it will go. Depress lever (B) and rotate table (C) to the 0 degree straight cut-of f position, r elease lever (B), and tighten locking knob (A).
7 7 4. Attach the fence slide support (E) Fig. 7D, to the extension table (B) by using the two 1 1/4” long hex head screws, 5/16” lockwashers and 5/16” flat washers (F). Bring scr ews up thr ough the two holes (G) in table extension and thread them into the two thr eaded holes (H) on bottom of fence slide support.
9. Position lock handle (M) Fig. JI, on stud and replace scr ew and spring (L) that wer e removed in STEP 7 . NOTE: Lock handle (M) is spring-loaded and can be repositioned by lifting up on handle. A TT ACHING DUST BAG Depress spring clips (A) Fig. 8, of dust bag (B) and clip dust bag (B) onto end of dust chute.
9 9 WARNING: A TURNING SA W BLADE CAN BE DANGEROUS. AFTER COMPLETING CUT , RELEASE SWITCH TRIGGER (A) FIG. 10, TO ACTIV A TE BLADE BRAKE. KEEP CUTTINGHEAD DOWN UNTIL BLADE HAS COME TO A COMPLETE STOP . WARNING: THE TORQUE DEVELOPED DURING BRAKING MA Y LOOSEN THE ARBOR SCREW .
10 10 T o adjust the sliding fit between the movable table and the base, turn nut (A) Fig. 14, clockwise to increase the sliding fit (opposite to decrease the fit). This adjustment should not be so tight that it restricts the r otating movement of the table, or so loose that it affects the accuracy of the saw .
11 11 TIL TING CUTTINGHEAD FOR BEVEL CUTTING CAUTION: DISCONNECT THE MACHINE FROM THE POWER SOURCE. IMPORT ANT : MOVE THE SLIDING FENCE TO THE LEFT TO PROVIDE CLEARANCE FOR THE BLADE AND GUARD. THE DEGREE OF TIL T DETERMINES HOW F AR TO MOVE THE SLIDING FENCE.
ADJUSTING CHIP DEFLECTOR 1. DISCONNECT THE SAW FROM THE POWER SOURCE. 2. A chip deflector (A) Fig. 22, is supplied to help prevent scrap or cut-off pieces fr om entering the upper blade guar d.
13 13 ADJUSTING SLIDING FIT BETWEEN TRUNNION AND BEVEL BRACKET After a long period of time, it may become necessary to adjust the sliding fit between the trunnion (A) Fig. 27, and the bevel bracket (B) by tightening the adjusting nut (C), Fig. 27, located underneath the bevel lock (A), Fig.
14 14 ADJUSTING BLADE GUARD After an extended period of time the movable blade guard (A) Fig. 30, might become sloppy and move erratically when the cuttinghead is lowered. This can be easily corr ected by slightly tightening nut (B) until the lower blade guard (A) moves smoothly .
15 15 CUTTING ALUMINUM Aluminum extrusions (aluminum screens and storm windows) can easily be cut with your miter saw . When cutting aluminum extrusions, or other sections that can be cut with a saw blade and are within the capacity of the machine, position the material so the blade is cutting through the smallest cr oss-section, as shown in Fig.
4. T o make the matching halves of the inside and outside corners, simply rotate the table to the 31-5/8 degree left miter position. NOTE: A positive stop is provided to find this angle quickly . The saw blade is already tilted to the 33-7/8 degr ee bevel position from the pr evious cut.
MAINTENANCE CHANGING THE BLADE WARNING: USE ONL Y CROSS-CUTTING SAW BLADES. DO NOT USE BLADES WITH DEEP GULLETS AS THEY CAN DEFLECT AND CONT ACT GUARD 1. Use only 12" diameter blades with 1" arbor holes that are rated for 4200 RPM or higher .
KEEP TOOL CLEAN Periodically blow out all air passages with dry compressed air . Clean all plastic parts with a soft damp cloth. NEVER use solvents to clean plastic parts. They could possibly dissolve or otherwise damage the material. CAUTION: WEAR SAFETY GLASSES WHILE USING COMPRESSED AIR.
19 19 Delta Building T rades and Home Shop Machinery T wo Y ear Limited W arranty Delta will repair or r eplace, at its expense and at its option, any Delta machine, machine part, or machine accessory.
20 20 NOTES.
The following are trademarks of POR TER-CABLE • DEL T A (Las siguientes son marcas r egistradas de PORTER-CABLE S.A.): BAMMER ® , INNOV A TION THA T WORKS ® , JETSTREAM ® , LASERLOC ® , OMNIJIG .
デバイスDeWalt 36-255の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
DeWalt 36-255をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはDeWalt 36-255の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。DeWalt 36-255の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。DeWalt 36-255で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
DeWalt 36-255を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はDeWalt 36-255の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、DeWalt 36-255に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちDeWalt 36-255デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
