DeWaltメーカーDCD775KLRの使用説明書/サービス説明書
ページ先へ移動 of 16
DC720- XE, DC730- XE, DC743- XE CORDLESS COMP ACT 1/2" (13 mm) DRILL/DRIVER DC725- XE, DCD775- XE, DC727- XE, DC737- XE CORDLESS COMP ACT 1/2" (13 mm) DRILL/DRIVER/HAMMERDRILL INSTRUCTION MA.
.
1 IF YOU HA VE ANY QUESTIONS OR COMMENTS ABOUT THIS OR ANY D E WAL T TOOL, CALL US A T : 1800 654 155 (Aust) or 0800 339258 (NZ). SAFETY INSTRUCTIONS FOR POWER TOOLS When using power tools, always obser ve the safety regulations applicable in your countr y to reduce the risk of fire, electric shock and personal injur y .
2 c) Prevent unintentional starting. Ensure the switch is in the off position before connecting to power source and/or battery pack, picking up or carrying the tool. Car r ying power tools with your finger on the switch or energising power tools that have the switch on invites accidents.
3 • Replacement of the supply cord. If the supply cord is damaged, it must be replaced by the manufacturer or an authorised D E WAL T Service Centre in order to avoid a hazard. Extension Cords CAUTION: Use only extension cords that are approved by the countr y’s Electrical Authority .
4 DANGER: Electrocution hazard. Never attempt to open the battery pack for any reason. If batter y pack case is cracked or damaged, do not inser t into charge r . Do not cr ush, drop or damage batter y pack. Do not use a batter y pack or charger that has received a sharp blow , been dropped, r un over or damaged in any way (i.
5 SPECIFIC SAFETY INSTRUCTIONS FOR LITHIUM ION (LI-ION) • Do not incinerate the battery pack even if it is severely damaged or is completely worn out. The batter y pack can explode in a fire. T oxic fumes and materials are created when lithium ion batter y packs are burned.
6 • An extension cord must have adequate wire size (AWG or American Wire Gauge) for safety . The smaller the gauge number of the wire, the greater the capacity of the cable, that is 16 gauge has more capacity than 18 gauge. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating.
7 Charge Indicators Some chargers are designed to detect cer tain problems that can arise with batter y packs. Problems are indicated by the red light flashing at a fast rate. If this occurs, re-inser t batter y pack into the charger . If the problem persists, try a different batter y pack to determine if the charger is OK.
8 OPERA TION WARNING: T o reduce the risk of serious personal injury , turn tool off and disconnect tool from power source before making any adjustments or removing/ installing attachments or accessories. FIG. 2 G FIG. 3 Installing and Removing the Battery Pack (Fig.
9 T o remove the battery pack from the tool , press the release buttons (G) and firmly pull the batter y pack out of the tool handle. Inser t it into the charger as described in the charger section of this manual. Variable Speed Switch (Fig. 1) T o turn the tool on, squeeze the trigger switch (A).
10 WARNING: T o reduce the risk of FIG. 4 DRILLING C personal injury , AL WA YS ensure workpiece is anchored or clamped firmly . If drilling thin material, use a wood “back-up” block to prevent damage to the material. 1. Use sharp drill bits only .
11 Screwdriver Operation (Fig. 6) 1. Select the desired speed/torque range SCREWDRIVING FIG. 6 C using the dual range gear selector to match the speed and torque of the planned operation. 2. T urn the torque adjustment collar to the desired position. Lower numbers indicate lower torque settings; higher numbers indicate higher torque settings.
12 • Damage caused where repairs have been made or attempted by others. • Damage due to misuse, neglect, wear and tear , alteration or modification.
13.
Battery Output Chargers/Charge Time Nominal 240 Volts 12 Volts X Indicates that the battery pack is not compatible with that specific charger. All charge times are approximate. Actual charge time may vary. Read the instruction manual for more specific information.
デバイスDeWalt DCD775KLRの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
DeWalt DCD775KLRをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはDeWalt DCD775KLRの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。DeWalt DCD775KLRの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。DeWalt DCD775KLRで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
DeWalt DCD775KLRを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はDeWalt DCD775KLRの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、DeWalt DCD775KLRに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちDeWalt DCD775KLRデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。