Airlink101メーカーN300の使用説明書/サービス説明書
ページ先へ移動 of 56
Wireless N 300 Multi-Function Access Point with 5-Port Switch Model # AP671W User’s Manual Ver. 1A.
1 Federal Communication Commission Interference Statement FCC Part 15 This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable pr otection against harmful interference in a residential inst allation.
2 Table of Contents FEDERAL COMMUNICATION COMMISSION INTERFERE NCE STATEMENT ........................................ 1 TABLE OF CONTENTS .........................................................................................................
3 Chapter 1 Introduction Congratulations on your purchase of AP671W, Airlink101 Wireless N 300 Multi-Function Access Point with 5-Port Switch! This product is ideal for home or SOHO users who need to add wireless capability to their existing wired network or extend the range for their wireless networks.
4 1.3 Access Point Interface Front Panel LEDs Back Panel Item Name Description Antenna Two 3dBi dipole antennas. Radio ON/OFF Switch the button to activate or deactivate the Router’s wireless function. Reset / WPS • Reset: Press this button and hold for 10 seconds to restore all settings to factory defaults.
5 1 ~ 5 Local Area Network (LAN) ports 1 to 5. Power Power connector DC 12V/1A, connects to A/C power adapter..
6 Chapter 2 Configuring the Access Point 2.1 Installing the Access Point to Your Network Step 1 Insert the provided CD into your computer’s CD ROM drive. You will be using this computer to configure the AP. Step 2 Click Next to start the configuration.
7 A. Connect the AP to the Router B. Power on the AP.
8 Step 4 Make sure the LEDs of POWER , WLAN and the LAN that is connected to the Router are lit. If not, try the above steps again. Step 5 Enter the AP’s password to log in to the AP. The default password is “admin”. It is recommended to change the AP’s password to protect your network security.
9 Step 7 Select an operation mode for your Access Point and click Next . Step 8 Configure the settings for the operation mode you have selected. A) Access Point Configure the SSID and Channel Number if y ou have selected Access Point mode. Click Next .
10 B) Universal Repeater Click on Site Survey , select the wireless router or AP you wish to repeat on the popup Wireless Site Survey window and click Connect .
11 Wireless Site Survey Configure wireless security settings according to the root AP’s settings. Th e Security Key you enter must match with the one of root AP.
12 Enter the key of the wireless network you wish to connect to. Click Next . D) Point-to-Point / Point-to-MultiPoint / WDS Bridge Same setup procedure applies to Point-to-Point Bridge, Point-to-MultiPoint Bridge and WDS Bridge modes. For bridge mode, you need at least two Access Points.
13 Configure the wireless security settings. It is recommended to use WPA2-PSK(AES) which is the safest encryption for general users. Click Next . After finishing the setup of the first AP, you need to follow th e same configuration procedure on other Access Point(s).
14 Step 10 Click Finish to end the EZ Setup Wizard. After the AP is restarted, it is ready to use. To configure more advanced features, please go to the next section.
15 2.2 Accessing the Access Point by Web Browser The EZ Setup Wizard will guide you through the basic configuration for t he Access Point. For more advanced settings, you will need to link to the Access Point’s Web-based Configuration Utility.
16 2.3 View System Status and Information After you connected to the access point by web browser, the first thing you see is ‘Status and Information’ page. All system and network related information of this access point will be displayed here.
17 Associated Clients Displays the number of connected wireless client. IP Address Displays the IP address of this wireless access point. Subnet Mask Displays the Subnet mask of IP address. Default Gateway Displays the IP address of default gateway.
18 2.4 Select an Operating Mode for Access Point This access point can be operated in different modes; you can click ‘Basic Setting’ on the left of web management interface to select an operat.
19 Please select one wireless operating mode, for detailed descriptions of every operating mode; please refer to Section 2.4.1 to 2.4.6 listed below. 2.4.1 AP Mode In AP mode, this access point acts as a bridge between 802.11b/g/Draft-N wireless devices and wired Ethernet network, and exchanges data between them.
20 Band Please select the wireless band you wish to use. By selecting different band setting, you’ll be able to allow or deny the wireless client of a certain band. If you select 2.4GHz (B), 2.4GHz (N), or 2.4GHz (G), only wireless clients using the wireless band you select (802.
21 This access point supports 4 sets o f SSID. Besides the main SSID (It can be configure in Basic Setting page), you can configure another three SSIDs here. With different SSIDs, you can separate the wireless networks with different SSID name, wireless security , WMM, and VLAN settings.
22 WMM WMM (Wi-Fi Multimedia) technology, which can improve the performance of certain network applications, like audio/video streaming, network telephony (VoIP), and others.
23 Here are descriptions of every setup item: Band Please select the wireless band you wish to use. By selecting different band setting, you’ll be able to allow or deny the wireless client of a certain band. If you select 2.4GHz (B), 2.4GHz (N), or 2.
24 procedures, or click “Apply” to reboot the router so the settings will take effect (Please wait for 30 seconds while router is rebooting). 2 4 2 1 Wireless Site Survey The table will list the access points nearby as the access point is set to St ation mode; you can select one of the access points to associate.
25 Mode Display the wireless modes include 11b, 11b/g or 11b/g/n or 11n only of the access points. Refresh Click this button to refre sh the table. Connection Select an access point and click this button to choose the network. The SSID name of the access point you have selected will be displayed in the Main SSID in the Basic Setting page.
26 Here are descriptions of every setup item: Band Please select the wireless band you wish to use. By selecting different band setting, you’ll be able to allow or deny the wireless client of a certain band. If you select 2.4GHz (B), 2.4GHz (N), or 2.
27 You can click “Continue” to back to previous setup page to continue on ot her setup procedures, or click “Apply” to reboot the router so the settings will take effect (Please wait for 30 seconds while router is rebooting).
28 Here are descriptions of every setup item: Band Please select the wireless band you wish to use. By selecting different band setting, you’ll be able to allow or deny the wireless client of a certain band. If you select 2.4GHz (B), 2.4GHz (N), or 2.
29 You can click “Continue” to back to previous setup page to continue on ot her setup procedures, or click “Apply” to reboot the router so the settings will take effect (Please wait for 30 seconds while router is rebooting).
30 Diagram 5: WDS Bridge mode application When you select ‘AP Bridge-WDS’, the following options will be displayed: Here are descriptions of every setup item: Band Please select the wireless band you wish to use.
31 Associated Clients Click ‘Show Active Clients’ button an d a new popup window will appear which contains the information about all wireless clients connected to this access point. You can click ‘Refresh’ butto n in popup window to keep information up-to-date.
32 Diagram 5: Repeater mode application When you select ‘Universal Repeater, the following options will be displ ayed: Here are descriptions of every setup item:.
33 Band Please select the wireless band you wish to use. By selecting different band setting, you’ll be able to allow or deny the wireless client of a certain band. If you select 2.4GHz (B), 2.4GHz (N), or 2.4GHz (G), only wireless clients using the wireless band you select (802.
34 You can click “Continue” to back to previous setup page to continue on ot her setup procedures, or click “Apply” to reboot the router so the settings will take effect (Please wait for about 30 seconds while router is rebooting).
35 2. Click ‘Set Security’ button when the wireless operating mode you selected is ‘AP Bridge-Point to Point’, ‘AP Bridge-Point to Multi-Point’, or ‘AP Bridge-WDS’. There are four types of security level you can select: Disable (no security - data encryption disabled), WEP, WPA Pre-shared Key, and WPA Radius.
36 Here are descriptions of every setup item: Key Length There are two types of WEP key length: 64-bit and 128-bit. Using ‘128-bit’ is safer than ’64-bit’, but will reduce some data transfer performance. Key Format There are two types of key format: ASCII and Hex.
37 2.5.2 WPA Pre-Shared Key WPA Pre-Shared key is the safest encryption method currently, and it’s recommended to use this encryption method to ensure the safety of your data.
38 Here are descriptions of every setup item: WPA Unicast Cipher Suite You can select WPA encryption type here. AES is safer than TKIP, but not every wireless client supports it. Please refer to the specification of your wireless client to decide which encryption type you should use.
39 Here are descriptions of every setup item: Use internal MD5/PEAP RADIUS Server Uses built-in RADIUS Server (refer to next Section) instead of external RADIUS server. If you check this box, the value of internal RADIUS server fields will be ignored.
40 2.6 Set Up MAC Filtering Another security measure you can use to keep hackers and intruders away is ‘MAC filtering’. You can pre-define a so-called ‘white-list’, which contains MAC addresses of the wire less clients you trust.
41 MAC address Input MAC address allowed using this wireless access point here. You don’t have to add colon (:) or hyphen (-) by yourself, just input 0 to 9 and a to f here, like 112233445566 or aabbccddeeff. Comment You can input any text here as the comment of this MAC address, like ‘ROOM 2A Computer’ or anything.
42 2.7 Configure Advanced Settings This wireless access point has many advanced wireless features. Please note that all settings listed here are for experienced users only, if you’re not sure about the meaning and function of these settings, please don’t modify them, or the wireless performance might be reduced.
43 N Data Rate Set the data rate of 802.11 Draft-N clients, available options are MCS 0 to MCS 15, it’s safe to set this option to ‘Auto’ and it’s not necessary to change this value unless you know what will happen after modification. Channel Width Select wireless channel width (bandwidth taken by wireless signals of this access point).
44 2.8 Configure WPS Setting Wi-Fi Protected Setup (WPS) is the simplest way to build connection between wireless network clients and this access point.
45 Wi-Fi Protected Setup Information All information related to WPS will be displayed here, they’re helpful when you’re setting up connections by WPS. WPS Status: Displays WPS status. If data encryption settings of this access point has never been set, ‘unConfigured’ message will be displayed her.
46 2.9 Configure Radius Server Comparing to other wireless security meas ures, radius server provides user-based authentication. If your wireless client supports 802.1x user authentication, you can use the ‘Radius Server’ function to use the internal mini radius server to improve security and wireless user control.
47 User Profile If you want to enable the Radius Server on this AP, you need to configure a User Profile, a set of allowed users and their passwords here. Please input username, password, re-type password in corresponding field, and click ‘Add’ button to add the user to radius server database.
48 2.10 Management 2.10.1 Change the password of the AP You can change the administrator’s password used to enter the web configuration utility of this wireless access point.
49 Default IP address is: 192.168.2.250 / Subnet Mask 255.255.255.0, please configure the IP address to match your network setting and make sure this IP address is always unique on your network. You can press and hold ‘Reset/WPS’ button over 10 seconds to change the IP address back to default value if you forget the IP address you set.
50 Here are descriptions of every buttons: Backup Settings Press ‘Save’ button, and you’ll be prompted to download the configuration as a file; default filename is ‘config.bin’, you ca n save it as another filename for different versions, and keep it on your local hard drive.
51 2.11.2 Upgrade the Firmwa re for the Access Point If there are new firmware versions of this wireless access point available, you can upgrade the firmware to the latest version to get extra functions or problem fixed.
52 2.11.3 Reboot the Access Point When you think the access point is not working properly, you can use this function to restart the access point; this may help and solve the proble m. This function is useful when the access point is f ar from you or unreachable.
53 Chapter 3 Troubleshooting If you found the access point is working impr operly or stop responding to you, don’t panic! Before you contact your dealer of purchase for help, please read this troubleshooting first.
54 Appendix A - Specification Standards • IEEE 802.11b/g/n Operation Mode • 6-in-1: Access Point , Universal Repeater, AP Client, Point to Point and Point to Multi-Point Bridge WDS Bridge Ante.
55 Technical Support E-mail: support@airlink101.com Toll Free: 1-888-746-3238 Website: www.airlink101.com † The GPL open source code can be downloaded at http://www.airlink101.com/gpl/ *Theoretical maximum wireless signal rate derived from IEEE standard 802.
デバイスAirlink101 N300の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Airlink101 N300をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはAirlink101 N300の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Airlink101 N300の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Airlink101 N300で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Airlink101 N300を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はAirlink101 N300の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Airlink101 N300に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちAirlink101 N300デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。