DeWaltメーカーDW717の使用説明書/サービス説明書
ページ先へ移動 of 16
DW717- XE 254 mm (10") DOUBLE BEVEL SLIDING COMPOUND MITER SA W INSTRUCTION MANUAL Questions? See us on the World W ide Web at www .dewalt.com.
T ABLE OF CONTENTS DOUBLE INSULA TION INSTRUCTIONS................................................................................................. ...........1 SAFETY INSTRUCTIONS FOR ALL TOOLS ......................................…………………………………………1 ADDITIONAL SAFETY RULES .
1 Definitions: Safety Guidelines The definitions below describe the level of severity for each signal word. Please read the manual and pay attention to these symbols. DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injur y .
2 2 • ST ABILITY . Make sure the miter saw is placed on a secure suppor ting sur face and does not slip or move during use. If the mobility kit is installed, raise the moveable caster(s) so saw is in its stationar y position. • FOLL OW ALL WIRING CODES and recommended electrical connections to prevent shock or electrocution.
3 3 Electrical Connection The electric motor has been designed for one voltage only . Always check that the power supply corresponds to the voltage on the rating plate. 230 V AC means your tool will operate on alter nating current. As little as 10% lower voltage can cause loss of power and can result in over heating.
4 Unpacking Y our Saw Check the contents of your miter saw car ton to make sure that you have received all par ts. In addition to this instr uction manual, the car ton should contain: 1. One DW717 miter saw . 2. One D E W AL T 10" (254 mm) diameter saw blade.
5 4. Depress the spindle lock button (C) while carefully rotating the saw blade by hand until the lock engages. 5. Keeping the button depressed, use the other hand and the wrench provided to loosen the blade screw . (T urn clockwise, lef t-hand threads) 6.
6 6 Adjustments WARNING: T o reduce the risk of serious personal injur y , turn off the tool and disconnect it from the power source before attempting to move it, change accessories or make any adjustments accept as written in laser adjustment instr uctions.
7 when the bevel lock handle is tightened. T o adjust the bevel lock handle, remove the screw in the center of the handle. Carefully pr y off the handle using a flat bladed screwdriver . Reorient and install the handle such that it will hold the bevel when tightened.
8 8 When cutting anything larger than 111.8 mm (4.4") [76.2 mm (3") 45º miter] use an out-down-back motion with the rail lock knob loosened. Pull the saw out, toward you, lower the saw head down toward the workpiece, and slowly push the saw back to complete the cut.
9 9 TO INST ALL CLAMP 1. Inser t it into the hole behind the fence. The clamp should be facing toward the back of the miter saw . The groove on the clamp rod should be fully inser ted into the base. Ensure this groove is fully inser ted into the base of the miter saw .
10 10 BEVEL SETTING TYPE OF CUT 33.85° Lef t LEFT SIDE, INSIDE CORNER: 1. T op of molding against fence 2. Miter table set right 31.62° 3. Save lef t end of cut 33.85° Right RIGHT SIDE, INSIDE CORNER: 1. T op of molding against fence. 2. Miter table set at lef t 31.
11 11 CUTTING LARGE MA TERIAL Occasionally you will encounter a piece of wood a little too large to fit beneath the blade guard. If this occurs, simply place your right thumb on the upper side of the guard and roll the guard up just enough to clear the workpiece, as shown in Figure 23.
12 12 MAINTENANCE DO NOT use lubricants or cleaners (par ticularly spray or aerosol) in the vicinity of the plastic guard. The polycarbonate material used in the guard is subject to attack by cer tain chemicals. 1. All bearings are sealed. They are lubricated for life and need no fur ther maintenance.
13 13 10 10 10 20 20 20 30 30 30 40 40 40 50 50 50 60 60 60 70 70 70 80 80 80 T ABLE 1: COMPOUND MITER CUT (POSITION WOOD WITH BROAD FLA T SIDE ON THE T ABLE AND THE NARROW EDGE AGAINST THE FENCE) SET.
D E W AL T Industrial T ool Co., 20 Fletcher Road, Mooroolbark, VIC 3138 Australia (03 8720 5100) • 5 T e Apunga Place, Mt W ellington, New Zealand (09 259 1111 ) (MAR08) Par t No.
デバイスDeWalt DW717の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
DeWalt DW717をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはDeWalt DW717の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。DeWalt DW717の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。DeWalt DW717で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
DeWalt DW717を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はDeWalt DW717の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、DeWalt DW717に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちDeWalt DW717デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。