DiamondメーカーDV190の使用説明書/サービス説明書
ページ先へ移動 of 28
2 DIAMOND VIEW ® DV190 Colour TFT LCD Monitor 19.0” (48.26 cm) LCD P anel Size User’s Manual.
2 Copyright 2003, Mitsubishi Electric Austra lia Pty. Ltd. All rights reserved. No part of this publication may be reproduced, tran smitted, transcribed, stor ed in a retrieval system or translated in.
i Table of Contents 1 1 Important Safety Instruct ions .......................................... 3 2 2 Featur es ............................................................................. 4 3 3 Unpacking th e Monito r .............................
ii Copyright Notice Copyright 2003, Mitsubish i Electric Aust ralia Pty. Ltd. All rights reserved. No part of this publication may be reproduc ed, transmitted, transcribed, stored in a retrieval syste.
3 1 1 Important Safety Instructions Please read the following safety instru ctions before installing or cleanin g your Diamond View monitor: 1. The AC adapter isolates this equi pme nt from the AC supply. 2. Unplug this product from the wall o utlet before cleaning.
4 2 2 Features Your Diamond View DV19 0 Monitor h as the following features: ♦ High Resolution, 1280 x 1024 Pixel L CD Pan el ♦ Super Slim Bezel Border Design ♦ High Brightness, Contras t Ra tio and Super Wide Viewing Angle 250 cd/m² brightness, 700:1 contra st ratio and ± 85/ ± 85(H/V) viewing angle.
5 3 3 Unpacking the Monitor Please check that the following items are included with your monitor. If they are missing or damaged, pl ease contact y our place of purchase immediately.
6 4 4 Hardware Installation Your monitor is equipped with an automatic powe r supply with a voltage range from 100 to 240 Volts AC at a frequency of 50 to 60 Hz. Make sure that your local power supply is within the supported ra nge. If you are unsure, please contact your electricity supplier.
DVI-D Cable Installation(Optional) 1. Make sure that the power to the computer and to the monitor are both turned off. 2. Connect one end of the monitor’ s DVI-D cable to the digital DVI-D connector (24-pin so cket) o f the computer‘s graphics card.
8 5 5 Windows Software Installation To get best performance with Wi ndows 95, 98, Mille nium Edition, 2 000 or XP you should set the PC to use the driver supplied with your DV1 90 monitor.
9 Windows Millennium Edition (Windows ME) The first time you start Windows with a new monitor; the system wil l detect it and automatically start the A d d Ne w Ha r d war e wizard. 1. Insert the Diamond View LCD Monitor Utilities floppy disk into your floppy disk drive.
10 1. Click on the Start button, go to Settin gs and select Control Panel . If needed, select S witch to Classic view from the left-hand side of the Control Panel window. 2. Dou ble click on Display , then click on the Settings tab at the top of the window that appears and select the Advanced button.
11 6 6 Setting the Display Resolution Choosing The Best Resolution All Liquid Crystal Displays (LCDs) have a fixed resol ution that is the same as the maximum resolution that may be displayed on the LCD. In the ca se of the DV190 the LCD resolution is 1280 x 1024 pixels.
12 4. A colour depth of either Thousands or Millions is recommended. MacOS X 1. Click the Apple icon at the top, left corner of the scre en, select System Preferences and then select Displays . 2. Select a resolution of 1280 x 1024 pixels with bet ween 60Hz and 75Hz refresh rate.
13 • Graphics modes th at are not listed in the table may not be supp orted. For an optimal picture it is recommended that you choose a graphi cs mode with a resolution of 1280 x 102 4pixels that is listed in Table 1 on the next page. All 22 modes are com patible with Microsoft Windows.
14 Resolution Horizontal Frequency (kHz) Vertical Frequency (Hz) Pixel Frequency (MHz) Comments 640x350 31.47(P) 70.08(N) 25.17 DOS 720x400 31.47(N) 70.08(P) 28.32 DOS 640x480 31.47(N) 60.00(N) 25.18 DOS 640x480 37.86(N) 72.80(N) 31.50 VESA 640x480 37.
15 Input Signal (Multi-scan mode) Resolution Horizontal Frequency (kHz) Vertical Frequency (Hz) Pixel Frequency (MHz) Comments 1024x768 60.02(P) 75.00(P) 78.75 VESA 1024x768 60.24 (N) 74.93 (N) 80.00 Macintosh 1152x864 67.50(P) 75.00(P) 108.00 VESA 1152x870 68.
16 7 7 Adjusting the Monitor Picture Optimisation The easiest way to obtain an optimal picture is by using the AU TO button. This only works reliably if the graphi cs ad aptor is set to use one of the monitor’s factory modes (see Table 1 in the previous chapter) and if you are displaying an appropriate full-screen test pattern.
6 5 4 3 2 1 1.Power on/ off: Turn the monitor on or off. 2.Enter: Enter sub-m e nus, select it ems, save change s. Hot Key: Press and hold for 3 second s, to select between “ Picture Mode” and “ Text Mode”. ( Note* ) 3. < >: Use these buttons to select a me nu item or make an adjustment when using the OSD.
18 To manually adjust the image: 1. Display the adjustment test pattern. This is the best way to observe changes as you adjust the image. Wind ows users should run the Auto.
19 The monitor will remember your settings and u se them whenever you turn the monitor on. Note that you may need to readjust the moni tor if it is connected to a different computer or if the compute r’s graphics adapto r is replaced.
20 8 8 Security Lock Installation The Diamond View DV19 0 can be secured to you r desk or any other fixed object with a Kensington lock se curity product. The Kensington lock‘s cabl e can be attached to a slot located at the rear of the monitor. 1. Insert the lock in the slot located on the rear of the monitor.
21 9 9 Frequently Asked Questions The image is blurred, how can I get the best quality picture? - Read c hapter 6, Setting the Display Resolution , and then select a graphics signal with the correct resolution and refresh rate. Then rea d chapter 7, Adjusting the Monitor , and make adj ustments to the displayed image based on these instructions.
22 No image is displayed, what can I do? - Check that the light (LED) next to t he monitor’s power button is lit and is green in colour. If the LED is green, press the "Exit" button on the monitor to access the On Screen Display.
23 1 1 0 0 Specifications Model Diamond View DV190 Display Characteristics Display Type 19.0“ active matrix Thin Film Transistor Liquid Crystal Display Viewable Diagonal Area 48.26 cm / 19.0” Native (Maximum) Resolution 1280 x 1024 pixels Colours 16.
24 Synchronisation TTL separate, composite TTL Signal Connection 15-pin mini D-sub cable 24- pin DVI-D cable Physical Characteristics Power M anagement VESA DPMS, Energy Star Maximum Power Consumption 40 Watts Power Sa ving Mode < 1 Watts Operating Voltage Automatic switched mode power supply, 100 - 264 V, 50 - 60Hz Dimensions (W x H x D) 415.
25 1 1 1 1 Service Contacts If problems remain after checking this manu al, please contact your place of purchase or contact Australian Service Contacts Visit the Mitsubishi Electric Australia web site at www.
Victoria and Tasmania 4 / 303 Burwood Hwy East Burwood, Vic, 3151 Telephone: (03) 9262-9899 Fax: (03) 9262-9850 Western A ustralia 5 / 329 Collier Road Bassendean, WA, 6054 Telephone: (08) 9377-3411 Fax: (08) 9377-3499 New Zealand Service Contacts Contact: BDT Ltd.
デバイスDiamond DV190の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Diamond DV190をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはDiamond DV190の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Diamond DV190の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Diamond DV190で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Diamond DV190を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はDiamond DV190の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Diamond DV190に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちDiamond DV190デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
