AirLiveメーカーPOE-100HD-ICRの使用説明書/サービス説明書
ページ先へ移動 of 89
PoE DC Iris MegaPixel IP Camera Use r ’ s Manual /POE-100HD-ICR AirLiv e POE-100HD.
Copyright and Disclaimer AirLive POE-100HD/ POE-100HD-ICR User ’s Manual Copyright & Disclaimer No part of this publication may be reproduc ed in any form or by any means, whether electronic, mechanical, photocopying, or record ing without the written consent of OvisLink Corp.
T able of Contents i AirLive POE-100HD/ POE-100HD-ICR User ’s Manua l Table of Contents 1. Overview .....................................................................................................1 1.1 Introduction .............................
T able of Contents AirLive POE-100HD/ POE-100HD-ICR User ’s Manual ii Appendix E: Specifications .........................................................................66 Appendix F: Configure Port Forwarding Manually .............................
1. Overview AirLive POE-100HD/ POE-100HD-ICR User ’s Manual 1 1 1. Overview This user’s guide explains how to operate this camera from a computer. User should r ead this manual completely and carefully before you operate the device. 1.1 Introduction This camera is an inexpensive and fully scalable surveillance device.
1. Overview AirLive POE-100HD/ POE-100HD-ICR User ’s Manual 2 Multi-channel control software for surveillance application On-line firmware upgrade 802.3af PoE support (wired model only) 1.3 Minimum System Requirements Microsoft Internet Ex plorer 6.
2. Package Content s AirLive POE-100HD /POE-100HD-ICR User ’s Manual 3 2 2. Package Content s User can find the following items in the package as below: Item Descriptions 1. This Unit is the main element of the product. And Camera Mount Kit and pads 3.
2. Package Content s AirLive POE-100HD/ POE-100HD-ICR User ’s Manual 4 2.1 Connections LAN LED Power LED 1. RJ45 LAN socket: Connect to PC or Hub/Switch.
2. Package Content s AirLive POE-100HD /POE-100HD-ICR User ’s Manual 5 3. Factory Default Reset This button is used to restore the all fact ory default settings.
2. Package Content s AirLive POE-100HD/ POE-100HD-ICR User ’s Manual 6 2.2 Mounting the Camera Ceiling Mount: Fix the camera to ceiling wi th the three supplied screws. Install the Camera in LAN 1. Plug an Ethernet cable into the Camera Connect an Ethernet cable to the LAN so cket and attach it into the network.
3. Preparation AirLive POE-100HD /POE-100HD-ICR User ’s Manual 7 3.1 Search and Set up by IPWizard II When you installed the Camera on a LAN envi ronment, you have two easy ways to search your Cameras by IPWizard II or UPnP™ discover y .
3. Preparation AirLive POE-100HD/ POE-100HD-ICR User ’s Manual 8 When launch the IPWizard II, a searching win dow will pop up. IPWizard II is starting to search Network Cameras on the LAN. The existed devices will be listed as below . Vi ew If IPWizard II finds network devices, View button will be available.
3. Preparation AirLive POE-100HD /POE-100HD-ICR User ’s Manual 9 LAN In case you want to change the IP related para meters of wired interfac e, please select the device you want to c onfigure and click the LAN button. Relative settings will be carried out as below .
3. Preparation AirLive POE-100HD/ POE-100HD-ICR User ’s Manual 10 In case, you do not want to change usernam e and/or password, then just cl ick “ Submit ” button to perform your setting accordingly . Click “ << ” button will go back to previous page.
3. Preparation AirLive POE-100HD /POE-100HD-ICR User ’s Manual 11 Note : Windows 2000 does not support UPnP feature. To discover your device, go to your Desktop and click My Network Places . Click the targeted Device. Then Internet Explorer will conn ect to this Network Camera automatically .
3. Preparation AirLive POE-100HD/ POE-100HD-ICR User ’s Manual 12 Installing the device with an UPnP router on your network is an easy 3–step procedure: (1) Enable UPnP option of your NAT rout.
3. Preparation AirLive POE-100HD /POE-100HD-ICR User ’s Manual 13 2. Type in your login name and passw ord u nder “USERNAME” and “PASSWORD” t e x t b o x .
4. Operating the Network Camera AirLive POE-100HD/ POE-100HD-ICR User ’s Manual 14 S tart-up screen will be as follow no matter an ordinary users or an administrator . 1. Monitor Image Section The image shot by the Network Camera is s hown here. The date and time are displayed at the top of the window.
4. Operating the Network Camera AirLive POE-100HD /POE-100HD-ICR User ’s Manual 15 The device could provide multiple langu ages to meet custom er’s requirement. 5. 2-Way Audio The device supports 2-way audio function. Us er can chose to enable or disable this function by toggling the icon below.
4. Operating the Network Camera AirLive POE-100HD/ POE-100HD-ICR User ’s Manual 16 (3) Camera speed: Choose the speed of Pan and Tilt. (4) Preset: Add/Update the preset positions or go to one of these positions. (5) Tour: Select one of the camera tours.
4. Operating the Network Camera AirLive POE-100HD /POE-100HD-ICR User ’s Manual 17 (1) Digit al Zoom Click Digit al Zoom to active this function as above. User can drag or scale the box over the video to adjust zoom ratio and position. (2) Record Click Record to activate this function.
4. Operating the Network Camera AirLive POE-100HD/ POE-100HD-ICR User ’s Manual 18 (3) Snap shot Click Snapshot to activate this function. Press Snap shot button to take a picture. The image file is saved as JPEG format into your local PC. Select Browser , the pop-up window to select the save path and file name prefix, select OK to continue.
4. Operating the Network Camera AirLive POE-100HD /POE-100HD-ICR User ’s Manual 19 (5) St atistics Click St atistics to activate this function. A window will b e popup to show the statistics information of the streaming status. Note that this information is the st atistics between the device and your local PC.
5. Administrating the Device AirLive POE-100HD/ POE-100HD-ICR User ’s Manual 20 5.1 System Setting This function is only available for user logged into Network Camera as administrator .
5. Administrating the Device AirLive POE-100HD /POE-100HD-ICR User ’s Manual 21 5.1.1 Network This section provides the menu for connecting the device through Ethernet cable. Network MAC address: Displays the Ethernet MAC addre ss of the device. Note t hat user can not change it.
5. Administrating the Device AirLive POE-100HD/ POE-100HD-ICR User ’s Manual 22 Obtain DNS from DHCP: DNS: Stands for Domain Name System. Enable this checked box when a DHCP server is installed on the network and provide DNS service.
5. Administrating the Device AirLive POE-100HD /POE-100HD-ICR User ’s Manual 23 A dynamic DNS service is uniqu e because it provides a means of updating your IP address so that your listing will remain current w hen your IP address changes. There are several excellent DDNS services available on the Internet.
5. Administrating the Device AirLive POE-100HD/ POE-100HD-ICR User ’s Manual 24 DDNSHost: The domain name is applied of this device. User name: The user name is used to log into DDNS.
5. Administrating the Device AirLive POE-100HD /POE-100HD-ICR User ’s Manual 25 PPPoE: To enable or disable the PPPoE service here. User name: Type the user name for the PPPoE servic e which is provided by the ISP. Password: Type the password for the PPPoE service which is provided by the ISP.
5. Administrating the Device AirLive POE-100HD/ POE-100HD-ICR User ’s Manual 26 RTSP Port: Choose the RTSP port. The RTSP protocol allo ws a connecting client to start a video stream. Enter the RTSP port number to use. The default value is 554. RTP Port: S pec ify the range of transmi ssion port number of video st ream.
5. Administrating the Device AirLive POE-100HD /POE-100HD-ICR User ’s Manual 27 UPnP: To enable or disable the UPnP service here. Friendly Name: Shows the friendly name of this device here. UPnP NAT Traversal When enabled, the device will at temp t to configure port mappi ng in a NAT router on your network, using UPnP™.
5. Administrating the Device AirLive POE-100HD/ POE-100HD-ICR User ’s Manual 28 IP Filter You can enter different user’s IP address whic h are allowing enter or denying by the device. IP Filter: To enable or disable the IP filter function here. IP Filter Policy : Choose the filter policy wher e is denying or allowing.
5. Administrating the Device AirLive POE-100HD /POE-100HD-ICR User ’s Manual 29 TCP Notification: If enable this function, then the “ TCP Server “, “ TCP Port ”, and “ Message ” fields need to be filled. TCP Server: Type the server name or the IP address of the TCP server.
5. Administrating the Device AirLive POE-100HD/ POE-100HD-ICR User ’s Manual 30 HTTP Login name: Type the user name for the HTTP server. HTTP Login Password: Type the password for the HTTP server. Proxy Address: Type the server name or the IP address of the HTTP Proxy.
5. Administrating the Device AirLive POE-100HD /POE-100HD-ICR User ’s Manual 31 5.1.2 Camera : Adjust Camera parameters Use this menu to set the functions of the camera p arameters of the device. Picture Rotation: T urn the “Mirror” and “V ertical Flip” On or OFF .
5. Administrating the Device AirLive POE-100HD/ POE-100HD-ICR User ’s Manual 32 White Balance: Auto: will adjust the white balance automatically. Hold: will hold the white balance. Exposure Control: Auto: will adjust the inte rnal gain automatically.
5. Administrating the Device AirLive POE-100HD /POE-100HD-ICR User ’s Manual 33 Baud rate: This is the communication speed between network module and P/T scanner. Note If need to change these parameters, user needs to check and set value properly for both, network module and P/T scanner .
5. Administrating the Device AirLive POE-100HD/ POE-100HD-ICR User ’s Manual 34 Up to 128 positions can be preset, and the ca mera can be programming to move to the preset position sequentially. Tour Name: The group name of the sequence of camera tour.
5. Administrating the Device AirLive POE-100HD /POE-100HD-ICR User ’s Manual 35 5.1.3 System : Configure and maintain sy stem Use this menu to perform the prin cipal settings of the device. System Device Title: You can enter the name of this unit here.
5. Administrating the Device AirLive POE-100HD/ POE-100HD-ICR User ’s Manual 36 Log: User can check the system log information of the device, including the Main Info , Appended Info , Operator IP , and so on … Reload: Click this button; user can refresh the log information of the device.
5. Administrating the Device AirLive POE-100HD /POE-100HD-ICR User ’s Manual 37 Maintenance Hard Factory Default (Include the network setting): Recall the device hard factory default settings . Note that click this button will reset all device’s parameters to the factory settings (including the IP address).
5. Administrating the Device AirLive POE-100HD/ POE-100HD-ICR User ’s Manual 38 Download the latest firmware file from our website or your dealer. Unzip this firmware file to binary file and store it into your PC. Then follow the steps as bellows carefully: 1.
5. Administrating the Device AirLive POE-100HD /POE-100HD-ICR User ’s Manual 39 5.1.4 Video : Configure profile This device provides 2 modes of video prof ile. The first one is Mega-pixel mode which supports video resolution up to Mega-pixel. Howe ver the maximum frame rate of this mode is up to 15fp s only .
5. Administrating the Device AirLive POE-100HD/ POE-100HD-ICR User ’s Manual 40 Rate Control: Defines the rate control method of this prof ile. There are two options: Constant Bit Rate (CBR) or V ariable Bit Rate (VBR). For CBR, the video bit rate is between low to high bandwidth based on dif ferent resolutions.
5. Administrating the Device AirLive POE-100HD /POE-100HD-ICR User ’s Manual 41 MPEG4 It’ s MPEG4 encoder mode in this profile. Resolution: There are three resolutions in th is profile: VGA, QVGA and QQVGA. Rate Control: Defines the rate control method of this prof ile.
5. Administrating the Device AirLive POE-100HD/ POE-100HD-ICR User ’s Manual 42 GOP Control: Defines the Intra/Inter-frame ( I/P) ratio of this profile. For ex ample, set the GOP to 30, then the video stream will have one In tra-frame every 30 frames.
5. Administrating the Device AirLive POE-100HD /POE-100HD-ICR User ’s Manual 43 5.1.5 Audio : Audio parameters Audio: To enable or disable audio function Audio Mode: To select Simplex or Fu ll duplex (2-way audio) mode Input Gain: To adjust gain of input audio Output Gain: T o adjust gain of output audio 5.
5. Administrating the Device AirLive POE-100HD/ POE-100HD-ICR User ’s Manual 44 5.1.7 E-Mail : Setup E-Mail configuration Y ou may setup SMTP mail p arameters for furt her operation of Event Schedule.
5. Administrating the Device AirLive POE-100HD /POE-100HD-ICR User ’s Manual 45 Test: Send a test mail to mail server to che ck this account is available or not. SMTP Port: Set port number of SMTP service. SMTP Authentication: Select the authentication requi red when you send an e-mail.
5. Administrating the Device AirLive POE-100HD/ POE-100HD-ICR User ’s Manual 46 Name: Name of the specified motion window. Object Size: Defines the object size of motion detection. The higher object size will only larger objects trigger motion detection.
5. Administrating the Device AirLive POE-100HD /POE-100HD-ICR User ’s Manual 47 Name: User can specify multiple FTP paths as wish. Therefore, user needs to specify a name for each FTP setting. FTP Server: Type the server name or the IP address of the FTP server.
5. Administrating the Device AirLive POE-100HD/ POE-100HD-ICR User ’s Manual 48 FTP Path: Set working directory path of FTP server. FTP Passive Mode: Select passive or active mode connecting to FTP server. TCP Server In addition to send video file to FTP server , the device also can send event message to specified TCP server.
5. Administrating the Device AirLive POE-100HD /POE-100HD-ICR User ’s Manual 49 Name: User can specify multiple HTTP servers as wish. Therefore, us er needs to specify a name for each HTTP server setting. URL: Type the server name or the IP address of the HTTP server.
5. Administrating the Device AirLive POE-100HD/ POE-100HD-ICR User ’s Manual 50 Proxy Login name: Type the user name for the HTTP Proxy. Proxy Login Password: Type the password for the HTTP Proxy. Proxy Port: Set port number of Proxy . SAMBA Server The device also can send video str eam to specified SAMBA server .
5. Administrating the Device AirLive POE-100HD /POE-100HD-ICR User ’s Manual 51 Test: Check the SAMBA server whether this account is available or not. SAMBA Login name: Type the user name for the SAMBA server. SAMBA Login Password: Type the password for the SAMBA server.
5. Administrating the Device AirLive POE-100HD/ POE-100HD-ICR User ’s Manual 52 Name: Name of the Event or Schedule. Enable: Enable or disable this Event or Schedule. Type: Event trigger or Schedule trigger. Enable Time: Define the feasible time slot.
5. Administrating the Device AirLive POE-100HD /POE-100HD-ICR User ’s Manual 53 Example 1: Send file to FTP server by motion triggered always: 1. Select event trigger 2. Enable time: start fr om 00:00 to 24:00 every day 3. T rigger by: Motion Area (Added in Object Detection page) 4.
5. Administrating the Device AirLive POE-100HD/ POE-100HD-ICR User ’s Manual 54 Example 3: Enable V oice Alert every 10-minute during 18:00 to 24:00 from Monday to Friday . 1. T ype: Select schedule trigger and interval is 10-minute. 2. Enable time: Select Monday to Friday , and set start time from 18:00 and keep work in 6 hours.
5. Administrating the Device AirLive POE-100HD /POE-100HD-ICR User ’s Manual 55 Record User can choose the type of record f ile for event or schedule application. Record File Type: Choose AVI or JPEG file format. Record File Prefix: Define the prefix of recorded filename.
Appendix A AirLive POE-100HD/ POE-100HD-ICR User ’s Manual 56 Appendix A: Alarm I/O Connector Some features of the Camera can be activated by the external sensor that senses physical changes in the area Camera is monitoring. These changes can include intrusion detection or certain physical change in the monitored ar ea.
Appendix A AirLive POE-100HD /POE-100HD-ICR User ’s Manual 57 CAUTION! • THE LOW VOLTAGE/CURRENT CIRC UITS AND HIGH VOLTAGE/ CURRENT CIRCUITS ARE IN THE NETWORK C AMERA CIRCUIT. TH E QUALIFIED ELECTRICIAN SHOULD DO THE WIRING NOT BY YOURSELF. I NCORRECT WIRING COULD DA MAGE NWTWORK CA MERA.
Appendix B AirLive POE-100HD/ POE-100HD-ICR User ’s Manual 58 Appendix B: Frequently Asked Questions Question Answer or Resolution Features The video and audio codec is adopted in the device. The device utilizes H.264, MPEG4 and JPEG triple compression to providing high quality im ages.
Appendix B AirLive POE-100HD /POE-100HD-ICR User ’s Manual 59 Forgot the username and password Follow the steps below. 1. Restore the factory default se tting by press pressing and holding down more than 3 seconds on the device. 2. Reconfigure the device.
Appendix B AirLive POE-100HD/ POE-100HD-ICR User ’s Manual 60 Internet Explorer • Maybe due to the network cable. Try correcting your network cable and configuration. Test t he network interface by connecting a local computer to the Network Camera via a crossover cable.
Appendix B AirLive POE-100HD /POE-100HD-ICR User ’s Manual 61 • Network congestion may prev ent the Image screen from appearing quickly. You may choose lower resolution to reduce the required bandwidth.
Appendix B AirLive POE-100HD/ POE-100HD-ICR User ’s Manual 62 Blank screen or very slow video when audio is enabled. • Your connection to the device does not have enough bandwidth to support a higher frame rate fo r the streamed image size. Try reducing the video streaming si ze to 160x120 or 320x240 and/or disabling audio.
Appendix B AirLive POE-100HD /POE-100HD-ICR User ’s Manual 63 Miscellaneous Can not play the recorded ASF file Have installed Microsoft®’s Dir ectX 9.0 or later and use the Windows Media Player 11.0 or later to play the AVI filed recorded by the Device.
Appendix C AirLive POE-100HD/ POE-100HD-ICR User ’s Manual 64 Appendix C: PING IP Address The PING (stands for Packet Internet Gr oper) command is used to detect whether a specific IP address is accessible by sending a packet to the specific address and waiting for a reply.
Appendix D AirLive POE-100HD /POE-100HD-ICR User ’s Manual 65 Appendix D: Bandwidth Estimation The frame rate of video transmitted from the device depends on connection bandwidth between client and server, video resolution, c odec type, and quality setti ng of server.
Appendix E AirLive POE-100HD/ POE-100HD-ICR User ’s Manual 66 Appendix E: Specifications Camera Image Device 1.3 Mega-pixel image sensor Effective Pixels 1280 x 1024 pixels Sensitivity 1.
Appendix E AirLive POE-100HD /POE-100HD-ICR User ’s Manual 67 Network Supported Protocols TCP, UDP, HTTP, SMTP, FTP, NTP, DNS, DDNS, DHCP, ARP, Bonjour, UPnP, RTSP, RTP, RTCP, PPPoE, 3GPP, ICMP, IGM.
Appendix E AirLive POE-100HD/ POE-100HD-ICR User ’s Manual 68 OS Windows® XP, Vista Browser IE 6.0 or latter / Firefox 2.0 or later Cell Phone With 3GPP player Video Player VLC, Quick Time, Real Pl.
Appendix F AirLive POE-100HD /POE-100HD-ICR User ’s Manual 69 Appendix F: Configure Port Forwarding Manually The device can be used with a router. If the device wants to be accessed from the WAN, its IP address needs to be setup as fixed IP address, also the port forwarding or Virtual Server function of router needs to be setup.
Appendix F AirLive POE-100HD/ POE-100HD-ICR User ’s Manual 70 Y our W AN IP Addre ss will be listed here. Note: Because a dynamic WAN IP can change from time to time depending on your ISP , you may want to obtain a S tatic IP address from your ISP .
Appendix F AirLive POE-100HD /POE-100HD-ICR User ’s Manual 71 Follow these steps to configure your router ’s V irtual Server settings • Click Enabled . • Enter a unique name for each entry. • Select Both under Protocol Type ( TCP and UDP ) • Enter your camera’s local IP Address (e.
Appendix G AirLive POE-100HD/ POE-100HD-ICR User ’s Manual 72 Appendix G: DDNS Application 1. Preface If you have a Cable modem or xDSL, this is a great way to host your own Networked Device or other TCP/IP Service. Get your own domain like w ww.yourname.
Appendix G AirLive POE-100HD /POE-100HD-ICR User ’s Manual 73 (3). After the columns show up at the left side, click “ Create Account” (4). Fill the application agreement and necessary information. a. Username b. E-mail address and confirmation c.
Appendix G AirLive POE-100HD/ POE-100HD-ICR User ’s Manual 74 Click these two options.
Appendix G AirLive POE-100HD /POE-100HD-ICR User ’s Manual 75 (5). Check your e-mail mailbox. There wil l be an e-mail with a title “Y our DynDNS Account Information“. Click the hyperlink addr ess to confirm the DDNS service that you just applied.
Appendix G AirLive POE-100HD/ POE-100HD-ICR User ’s Manual 76 Input your account (7). If the correct username and password are input, you can see the following picture at the top -right of the login page. ( 8 ) . C l i c k t h e “ Services”. ( 9 ) .
Appendix G /POE-100HD-ICR User ’s Manual (10). Click the “ Get S tarted ”. (1 1). We could create a domain name without any charge at this step. First, we input the host name. (Pink No.1) Then we pick a domain that is easy to remember . ( P i n k N o .
Appendix G AirLive POE-100HD/ POE-100HD-ICR User ’s Manual 78 4. Setup the DDNS and PPPoE of Networked Device At last, users have to enter the web p age of Networked Device and setup the necessary information of DDNS and PPPoE after the applicat ion of DDNS service.
Appendix H AirLive POE-100HD /POE-100HD-ICR User ’s Manual 79 Appendix H: Power Line Frequency COUNTR Y V O LTA G E FREQUENCY COMMENTS Argentina 220V 50 Hz *Neutral and line wires are reversed from that used in Australia and elsewhere. Australia 230V* 50 Hz *Outlets typically controlled by adjacent switch.
Appendix H AirLive POE-100HD/ POE-100HD-ICR User ’s Manual 80 Netherlands 230V 50 Hz Portugal 230V 50 Hz S pain 230V 50 Hz Sweden 230V 50 Hz Switzerland 230V 50 Hz T aiwan 1 10V 60 Hz Thailand 220V 50 Hz United Kingdom 230V* 50 Hz *Outlets typically controlled by adjacent switch.
Appendix I AirLive POE-100HD /POE-100HD-ICR User ’s Manual 81 Appendix I: 3GPP To use the 3GPP function, in add ition to previous section, you might need more information or configuration to make this function work.
Appendix J AirLive POE-100HD/ POE-100HD-ICR User ’s Manual 82 Appendix J: Enable UPnP of Windows XP Use the following steps to enable UPnP settings only if your operati ng system of PC is running Windows XP .
Appendix J AirLive POE-100HD /POE-100HD-ICR User ’s Manual 83 Click Add/Remove Windows Components The following screen will appear: Select Networking Services.
Appendix J AirLive POE-100HD/ POE-100HD-ICR User ’s Manual 84 Click Det ails Select Universal Plug and Play Click Ok.
Appendix J AirLive POE-100HD /POE-100HD-ICR User ’s Manual 85 Click Next Please wait while Setup configures the components. Click Finish.
デバイスAirLive POE-100HD-ICRの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
AirLive POE-100HD-ICRをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはAirLive POE-100HD-ICRの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。AirLive POE-100HD-ICRの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。AirLive POE-100HD-ICRで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
AirLive POE-100HD-ICRを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はAirLive POE-100HD-ICRの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、AirLive POE-100HD-ICRに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちAirLive POE-100HD-ICRデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。