AirLiveメーカーWH-9200APの使用説明書/サービス説明書
ページ先へ移動 of 33
W H-9200AP 802.11a/b/g Dual Radio W ireless Base Station Use r ’ s Manual.
Regulatory Information Federal Communication Commission Interference S t atement This equipment has been tested and found to co mply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Ru les. These limits are designed to provide reasonable protection against harmful interference.
Table of Contents 1. Introduction ................................................................................................2 1.1 Overview ..............................................................................................2 1.2 Install ing WH-9200AP .
1. Introduction 1.1 Overview The WH-9200AP is a dream device for WISP to build their wireless networks. The WH-9200AP features 2 At heros that run in 5G Hz or 2.4GHz frequency band. There is an intergraded 802.3af POE port to let you run the WH-9200AP at up to 100 meter distance away from the power source.
1.2.1 Package Content The WH-9200AP package contai ns the following items: z One WH-9200AP main unit z 48VDC PoE injector kits z Pole/Wall mount kit z One CD of the WH-9200AP 1.
WLAN port when operate in Gateway mode 5 Ground Pin - Reference point for electric current 6 Sluice - Sluice out the water in device N-T ype connector for outdoor antenna of Radio 2.
Antenna 2 Antenna 2 Pole Mount/W all mount Installa tion 5 AirLive WH-9200AP User ’ s Manual.
Power Inst allation The following image shows the power installation of WH-9200AP . Note that WH-9200AP is IEEE802.3af compatible, you should use the packed kit or POE Switch for power injection.
1.2.3 Configuration Setups The factory default settings of WH-9200AP are as following: Default V alue Settings Wireless1 Wireless2 Device Name WH-9200AP Radio 802.1 1a 802.1 1b/g SSID airlive1 airlive2 IP Address 192.168.1.1 DHCP Server Disabled. A vailable and def ault enabled when each of the wireless is configured as a gateway .
Access to management interface 1 Please make sure your computer IP is in the same subnet as the WH-9200AP (i.e. 192.168.1.x). 2 Please make sure your computer has wireless network adapter installed. 3 Open the web browser and enter http://192.168.1.1/.
2. Wirless Settings 2.1 Client + AP Mode In this mode, the Radio1 will operate in 5G Hz 802.1 1a as Client mode while Radio2 will operate in 2.4GHz 802.1 1g/b as AP mode. The Radio1 operates in 5470~5725MHz, Radio2 operate in Channel 1~1 1 only . Client mode is also known as Ethernet Client.
T o connect to an access point, use the “Site Survey ” button to find the Access Point. The Site Survey pop up window then shows up and lists available access point with relative information. Select the access point you want to connect and then click the “ASSOCIA TE” button.
After the access point is selected, it s SSID s hows automatically in the Network ID (SSID) field. 11 AirLive WH-9 200AP User ’ s Manual 2.2 Wireless Security The wireless security is to configure a se cure connection between two wireless devices. WH-9200AP provides WEP , 802.
WEP WEP allows you to use data encryption to secure your dat a from being eavesdropped by malicious people. It allows 3 types of key: 64 (WEP64), 128 (WEP128), and 152 (WEP152) bits. Y ou can configure up to 4 keys us ing either ASCII or Hexadecimal format.
Rekey interval is time period that the system will change the key periodically . The shorter the interval is, the better the security is. eneral you don’t have to change Port Number , which is After.
Encryption T ype : There are two encryption types TKIP and CCMP (AES) . While CCMP provides better security than TKIP , some wirel ess client st ations may not be equipped with the hardware to support it. Y ou can select Both to allow TKIP clients and CCMP clients to connect to the Access Poin t at the same time.
Pre-shared Key : T his is an ASCII string with 8 to 63 characters. Please make sure that both the WH-9200AP and the wir eless client stations use the same key .
WP A2 WPA2 stands for Wi-Fi Protected Access 2. It provides stronger data protection and network access control then WPA. Only authorized users can access the wireless networks.
WP A2-PSK Enter the Pre-shared Key to initiate WPA2 se curity. All devices try to access the network should have the matching encryption key. Pre-shared Key : T his is an ASCII string with 8 to 63 characters. Please make sure that both the WH-9200AP and the wir eless client stations use the same key .
WP A-AUTO Encryption T ype : There are two encryption types TKIP and CCMP (AES) . While CCMP provides better security than TKIP , some wir eless client stations may not be equipped with the hardware to support it. Y ou can select Both to allow TKIP clients and CCMP clients to connect to the Access Poin t at the same time.
WP A-PSK-AUTO WPA-PSK-AUTO tries to authenticate wirele ss clients using WPA-PSK or WPA2-PSK. Pre-shared Key : T his is an ASCII string with 8 to 63 characters. Please make sure that both the WH-9200AP and the wir eless client stations use the same key .
2.3 Advanced Wireless Settings When click on Advanced Setup button under client mode, a pop- up window appears and show parameter as fo llow: Beacon Interval: The WH-9200AP broadcasts beacon frames regularly to announce its existence. The beacon Interval specifies how often beacon frames are transmitted in time unit of milliseconds.
power-conserving stations that there are p ackets waiting to be received by them. The DTIM interval specifies how often the beacon frame should cont ain DTIMs. User Limit ation: The range of user limitat ion is from 1 to 100. Age Out T imer: Set the age out time.
The ACK value then shows up after calculating Enter the calculated value of “AckTimeOut” into the appropriate “Ack T imeOut” field (1 1a or 1 1g) in the “Advanced Wireless Settings” window . Change the value from 25 to 107, where 107 is calculated value of distanced 12 500m.
3. System Management Y ou can review the Device information of your WH-9200AP by the interface. The information shows the current firmware version, IP address of your WH-9200AP . Wireless1 MAC and Wireless2 MAC show the MAC address of the two radios, the information helps to setup WDS connection by remote access point.
3.2. System Management Settings The WH-9200AP allow you to change the parameter of manage the system. HTTP Port No.: This is to change the management web port of WH-9200AP . By default, the port number is 80 and we type http://192.168.1.1 in the browser to access the management web page.
Syslog server IP address: The Syslog can also send to the identified IP address. The system log shows in WH-9200AP: 25 AirLive WH-9 200AP User ’ s Manual.
3.3. SNMP Settings WH-9200AP can also be managed by remote software with SNMP (simple network management protocol) protocol. System Name: A name that you assign to your WH- 9200AP for SNMP software. It is an alphanumeric string of up to 30 characters.
Community String For Write: For read-write operation, y ou need to configure a write “community string”. Assign a specific name and IP addr ess for your SNMP trap manager: A trap manager is a remote SNMP management station where special SNMP trap messages are generated (by the route r) and sent to in the network.
3.4. Firmware Upgrade Y ou can upgrade the firmware of your WH-9200AP (the softwa re that controls your WH-9200AP’ s operation). Normally , this is done w hen a new version of firmware offers new features that you want, or solves probl ems that you have encount ered with the current version.
3.5. Configuration Save and Restore In this interface, you can backup your system configuration to PC and restore your saved configuration file to the WH-9200AP . T o save the configurati on to your PC, click the “SA V E T O FILE” button and the system will lead you to save the configuration file to your PC.
3.6. Reboot System The following interface allows you to reboot your WH-9200AP . Click “Y es” button to reboot. Y ou can also reboot WH-9200AP by power off and power on it.
3.7. WH-9200AP Emergency Recovery This document guides to recover your WH -9200AP system if t he firmware crashed. 1. Download t he t ftp server to your PC. In the following exampl e, we use t ftpd32: http://tf t pd32.jounin. net/t ftpd32_download.html .
デバイスAirLive WH-9200APの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
AirLive WH-9200APをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはAirLive WH-9200APの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。AirLive WH-9200APの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。AirLive WH-9200APで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
AirLive WH-9200APを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はAirLive WH-9200APの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、AirLive WH-9200APに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちAirLive WH-9200APデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
