DimplexメーカーWRCPF-KITの使用説明書/サービス説明書
ページ先へ移動 of 20
Owner ’ s Manual Model WRCPF-KIT 72091 10100R03 IMPORT ANT SAFETY INFORMA TION: Always read this manual rst before attempting to install or use this device. For your safety , always comply with all warnings and safety instructions contained in this manual to prevent personal injury or property damage.
2 www .dimplex.com T able of Contents ! NOTE: Procedures and techniques that are considered important enough to emphasize. CAUTION: Procedures and techniques which, if not carefully followed, will result in damage to the equipment.
3 W elcome & Congratulations Thank you and congratulations for choosing to purchase a W all Switch Remote Control Kit from Dimplex, the world leader in electric replaces. Please carefully read and save these instructions. CAUTION: Read all instructions and warnings carefully before starting installation.
4 www .dimplex.com Product Overview The W all Switch Remote Control Kit is designed to work with the following Dimplex electric replaces: BF33STP • BF33DXP • BF39STP • BF39DXP • BF45DXP •.
5 Receiver Installation (BF units only) Open steel curtain (remove 1. glass doors if applicable). Remove two (2) screws on l og 2. grate and remove log grate (Figure 1). Locate and remove the two (2) 4. screws on the manual control bracket (Figure 3).
6 www .dimplex.com Locate the plastic 9-pin plug 6. in the bottom corner of the replace where the manual controls were plugged in to. Insert the plug connector from 7. the remote control bracket (Figure 4) into plastic plug inside the replace. ledge (Figure 2) and the logs are resting against the partially reective glass.
7 W all Control Installation ! NOTE: All electrical w iring must comply with all national and local electrical codes and regulations. Always use a qualied and licensed electrician should you have any questions or concerns for all wiring work. ! NOTE: The W all Switch Remote Control is made to t standard Decora style faceplates.
8 www .dimplex.com Figure 5 Outer Housing Controller 2. Release the Controller from its Outer Housing by pushing the front face into the Outer Housing until you hear a click. This will release the push- lock latches and allow the Controller to be removed from the Outer Housing (Figure 5).
9 W all Control Installation to complete the installation and to blend the installation in with your choice of decor . Hard Wired Power Supplied Installation Before starting this installation, it is helpful to initialize the W all Switch Remote Control with your rebox (see Initialization section).
10 www .dimplex.com W all Control Installation 1. Unpack the W all Switch Remote Control and all hardware from its package. 2. Release the Controller from its Outer Housing by pushing the front face into the Outer Housing until you hear a click.
11 W all Control Installation Figure 12 Controller Outer Housing Figure 13 Locking Screw Option (Figure 14) T o prevent tampering, damage, and theft, it is suggested to install the locking screws.
12 www .dimplex.com W all Control Installation Figure 15 Ensure each of the two Controller lead wires are connected to separate Low V oltage 24V~ only wires.
13 ! NOTE: Wire leads are not polarized due to the nature of this device. 9. Coil excess wiring to the back of the device box and insert the Controller and Outer Housing int o t he d evi ce box (Fi gur e 16 ). Fasten with two supplied at head screws.
14 www .dimplex.com Initialization After installation, locate the section which applies to your specic model of replace and follow the steps for remote control initialization and if required, re-initialization. Refer to your replace's owner's manual to locate manual or other controls as needed.
15 Initialization DF3033ST and DFG3033 Models 1. Ensure that power is supplied through main service panel. 2. Ensure the Main On/Off Switch located in the switch box on the replace in the upper right hand corner is in the On position (Figure 19A) .
16 www .dimplex.com Operation A. On Button Pressing this button toggles sequentially through the three levels of the replace. Pressing once activates Level 1 - ame effect only , twice activates Level 2 - ame effect and Purire™, three times activates Level 3 - ame effect, Purire™ and heat.
17 Operation W all Switch Remote Control 1 3 5 2 4 6 7 9 11 8 10 12 13 14 1. Room T emperature 2. Set T emperature 3. Flame Effect 4. Purire™ 5. Heat Off Indicator 6. Function Lock Indicator 7. RF Code Function Indicator 8. Set T emperature Down 9.
18 www .dimplex.com Operation 1. Room T emperature Displays current ambient temperature in the room. 2. Set T emperature Displays and controls the heater to the temperature at which the thermostat is currently set to. Press 8 to lower the thermostat and press 9 to raise the thermostat.
19 Operation 7. RF Code Function and Change Procedure In the event that the W all Switch Remote Control does not work properly with the receiver due to interference from additional wireless signals, this function will allow the RF code to be changed. T o enable this function, press 9 and 12 together .
20 www .dimplex.com W arranty This Dimplex W all Switch Remote Control is warranted against defects in workmanship and materials for two years from date of sale.
デバイスDimplex WRCPF-KITの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Dimplex WRCPF-KITをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはDimplex WRCPF-KITの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Dimplex WRCPF-KITの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Dimplex WRCPF-KITで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Dimplex WRCPF-KITを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はDimplex WRCPF-KITの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Dimplex WRCPF-KITに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちDimplex WRCPF-KITデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
