Dixonメーカー10504-1101の使用説明書/サービス説明書
ページ先へ移動 of 44
ZTR ® OPERA T OR’S MANUAL ZEETER® CLASSIC 2002.
IMPORTANT - READ CAREFULLY The Dixon ® ZTR ® Mower is both easy and fun to operate. However, any power mower must be operated properly to be safe. It is not a toy or a recreational vehicle. Before you start to use the mower, read the operator’s manual carefully and become completely familiar with the controls.
3 INDEX Page Safety. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-11 Warranty Policy. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 2 Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4 RIDING LAWN MOWERS, IF IMPROPERLY OPERATED, CAN CAUSE SERIOUS INJURY OR DEATH. The most common causes of injury to the operator or bystander... ...read and understand this manual to prevent injuries.
5 Safety Alert Symbol When you see this symbol, BE ALERT to the potential for injury. DANGER (highlighted in red) indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
6 Failure to observe the following safety instructions could result in serious injury or death. GENERAL OPERATION: • Read, understand, and follow all instructions in the manual and on the mower before starting. •Only allow responsible adults, who are familiar with the instructions, to operate the mower.
7 GENERAL OPERATION (continued) : •Turn off blades when not mowing. •Stop engine before removing grass catcher or unclogging chute. •Mow only in daylight or good artificial light. •Do not operate the mower while under the influence of alcohol or drugs.
8 SLOPE OPERATION: Slopes are a major factor related to loss-of-control and tip-over accidents, which can result in severe injury or death. All slopes require extra caution. If you cannot back up the slope or if you feel uneasy on it, do not mow it! DO • Mow across the slope with your Dixon ZTR - never up or down.
9 SAFETY CHILDREN: Tragic accidents can occur if the operator is not alert to the presence of children. Children are attracted to lawn mowers and the mowing activity. NEVER assume children will stay where they were last seen. Be alert to avoid accidents.
10 SERVICE: •Use extra care in handling gasoline and other fuels. They are flammable and vapors are explosive. Use only an approved container. Never remove fuel cap or add fuel with engine running. Allow engine to cool before refueling. Do not smoke while refueling.
11 SERVICE (continued): •Never run a mower inside a closed area. The exhaust fumes are toxic. •Keep nuts and bolts tight, especially blade attachment bolts, and keep equipment in good condition. •Never tamper with safety devices. Check their proper operation regularly.
12 DIXON INDUSTRIES, INC. a BLOUNT company Airport Industrial Park P.O. Box 1569 Coffeyville, Ks 67337- 0945 620-251-2000 Fax 620-251-4117 DIXON LIMITED WARRANTY POLICY 3000 & 4000 Series & ZEETER Classic WARRANTY: Home Owner Application: This Dixon Warranty term is for a period of two (2) years from date of purchase.
13 SPECIFICATIONS Model ZEETER Classic CHASSIS: 11 GA welded rectangular tubing BODY: All body parts made of high density polyethylene. Dent and corrosion resistant. Front body contains access panel for battery service. MOWER DECK: 13 GA stamped steel construction.
14 SEAT ADJUSTMENT INSTRUCTIONS Model ZEETER Classic 1. Raise and push seat assembly forward. 2. Loosen seat adjustment knobs and slide seat forward or backward to desired position. 3. Re-tighten nuts. DO NOT operate mower without seat adjustments properly tightened.
15 CONTROLS The Dixon ZTR has a unique transaxle that requires only two drive levers to control braking, turning, speed and direction. On initial operation, set throttle speed on slow. Operate with mower blade in “OFF” position. To avoid “over-controlling” the mower, use a light touch on the drive levers.
16 CONTROLS CONTROL LEVERS TO GO FORWARD: • From neutral position, gently push both control levers forward. • To increase speed, move levers further forward.
17 CONTROLS BLADE DRIVE: • Located on the control panel, on the operator’s right. • To engage the mower blades, pull up on the switch. • To disengage mower blade, push down. CIRCUIT BREAKER: • Protection of the electrical system is by (1) 15 amp circuit breaker.
18 OPERATION INSTRUCTIONS The safe and successful operation of the ZEETER Classic mower will depend upon the operator having the correct knowledge of all controls used on the mower and making good judgements about the terrain to be mowed. NEVER allow anyone to operate the mower without complete knowledge of all controls and their functions.
19 OPERATION INSTRUCTIONS BEFORE OPERATING MOWER: 1. Read and observe all safety instructions on your mower and in the manual. 2. Read engine manufacturer’s operating and maintenance instructions. 3. Check engine oil. 4. Check fuel cap to be sure it is in place.
20 OPERATION INSTRUCTIONS TESTING OF SAFETY INTERLOCK SYSTEMS: Do not operate mower if safety switches are not operating properly. BLADE DRIVE SWITCH TEST: a) Engage blade drive switch. b) Turn ignition switch to START. ENGINE SHOULD NOT TURN OVER OR ATTEMPT TO START! SEAT SWITCH TEST: a) In a SAFE AREA away from bystanders, start the engine.
21 OPERATION INSTRUCTIONS STARTING INSTRUCTIONS: 1. Parking brake must be on, and blade drive disengaged. 2. Move throttle control to “choke” position if engine is cold, full throttle if warm. 3. Insert ignition key and turn to “start” position.
22 OPERATION INSTRUCTIONS SIDE DISCHARGE OF THE CLIPPINGS: In order to achieve optimum performance when side discharging the grass clippings, please read and follow the tips listed below. Additional information can be found in the troubleshooting guide.
23 OPERATION INSTRUCTIONS GRASS HEIGHT AND CUTTING SUGGESTIONS: As a rule of thumb, never cut off more than 1/3 of the total grass blade length. Correct mowing height can reduce weeds and disease by 50% to 80%. The following grass cut heights are based on adequate moisture conditions and normal thatch build-up in a healthy lawn.
24 OPERATION INSTRUCTIONS MOWING WITH A MULCHING ATTACHMENT: Mulching or recycling the grass clippings requires a totally different mowing approach than would be normal when side discharging or bagging the grass. There may be instances or conditions where it is not possible to hide all of the recycled or mulched clippings.
25 OPERATION INSTRUCTIONS MOWING WITH A MULCHING ATTACHMENT (continued): 6. Keep the Underside Of The Mower Deck Clean. Remove all grass and dirt build-up from the underside of the pan, the baffles and deflectors after each use. 7. Alternate mower direction.
26 OPERATION INSTRUCTIONS MOWING WITH A GRASS CATCHER ATTACHMENT: In order to achieve optimum performance when mowing with a grass catching attachment, please read and follow the tips listed below. 1. Set engine speed control to the wide open or full setting and engage mower before entering area to be cut.
27 OPERATION INSTRUCTIONS MOWING WITH A GRASS CATCHER ATTACHMENT (continued): 7. Operate the mower at a slower ground speed than when mowing without a grass catching attachment. 8. Some mowing applications/use of grass catchers may require that an optional weight box be fitted to the mower to counter the weight of grass in the bags.
28 CARE AND MAINTENANCE CAUTION CAUTION CAUTION CAUTION CAUTION Bef Bef Bef Bef Bef ore perf ore perf ore perf ore perf ore perf or or or or or ming an ming an ming an ming an ming an y maintenance y .
29 CARE AND MAINTENANCE ENGINE: For complete maintenance and operating information of the engine, please refer to the maintenance instructions furnished by the engine manufacturer and included in your Zero Turn Radius mower informa- tion packet. BATTERY: • This is a maintenance-free battery and the fluid level cannot be checked.
30 CARE AND MAINTENANCE CUTTER BLADE MAINTENANCE: CAUTION Stop engine and remove ignition key for safety. Wear heavy, thick gloves when holding onto cutter blade.
31 CARE AND MAINTENANCE BELTS: Check belts every 50 hours. Replace any belts found to be in poor condition. BELT TENSION: Transaxle Drive Belt: P/N 1684 No adjustment required. Engine to Mower Deck Belt: P/N 6111 No adjustment required. Correct belt tension is maintained through a fixed engine location and a spring loaded idler system.
32 CARE AND MAINTENANCE MOWER DECK LEVELING PRCEDURE: 1. Place mower on a smooth, level surface and check tire pressures to insure correct stance. Tires should be inflated as follows: Front: 16-21 lbs Rear: 8-14 lbs 2. Turn each outer blade tip to align with the deck in a side to side manner.
33 CARE AND MAINTENANCE DECK REMOVAL: 1. Place cut height lever in lowest cut position. 2. Pull belt idler back to allow belt to be removed from idler pulley and electric clutch pulley. 3. Remove hair pin cotter and washer from one end of deck support cross shaft.
34 Hex Head Valve Stem HOT oil may cause burns. Allow engine to cool before draining oil. CAUTION CARE AND MAINTENANCE CHANGING THE ENGINE OIL: 1. The “Dapco” oil drain valve is located on the left side of the engine crankcase. 2. Place a suitable container under the drain valve.
35 CARE AND MAINTENANCE DRIVE SYSTEM ADJUSTMENTS: Due to both the complex nature of the transmission and the number of special tools required for service, adjustments should be entrusted to your dealer. There are a number of simple owner service items which greatly influence the performance of the drive system.
36 CARE AND MAINTENANCE REAR CHAIN ADJUSTMENT: To adjust the rear drive chains on the Zeeter Classic, tighten the nut on top of the spring on each side of the mower chassis. Tighten until the chains have approximately 1/4” movement up and down when measured at a mid point.
37 CARE AND MAINTENANCE LUBRICATION: CHASSIS: (7) grease zerks used LOCATIONS: (1) each front wheel caster & front wheel hub (1) each mower deck hub SERVICE INTERVALS: Every 50 hours of operation RECOMMENDED GREASE: Name brand wheel bearing or multi-purpose grease.
38 CARE AND MAINTENANCE ELECTRICAL SYSTEMS: Keep all connections clean and tight. CLEANING THE MOWER: Wash mower periodically. Clean above and below deck. Note: Allow mower to cool before washing. If bearings are hot, they will draw moisture inside as they dry & cause corrosion.
39 STANDARD SERVICE PARTS LIST Blades: P/N 8688 (Standard/Hi-Lift) P/N 6236 (Lo-Lift) Belts: Engine to Mower Deck - P/N 6111 Engine to Transmission - P/N 1684 Serpentine Blade Drive - P/N 1684 BRIGGS .
40 1. ENGINE WON’T TURN OVER Mower blades engaged- - - - - - - - - - - - - - - - - - - - - - -disengage blades Circuit Breaker Trips- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -res.
41 TROUBLESHOOTING 6. ENGINE RUNS BUT MOWER WON’T MOVE FORWARD Drive belt broken or slipping- - - - - - - - - - - - - - - - - - - - replace drive belt Bad transmission- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - consult dealer 7.
42 NOTES.
43 OWNER INFORMATION Date Purchased _ ________________________________ Mower Model Number ____________________________ Mower Serial Number ____________________________ Purchased From ___ _____________.
ZTR®Mowers ZTR®Mowers ZTR®Mowers ZTR®Mowers ZTR®Mowers Dixon® and ZTR® are registered trademarks of Dixon Industries, Inc. DIXON INDUSTRIES, INC. a BLOUNT International Inc. Co. P.O. Box 1569 Coffeyville, Ks 67337-0945 620-251-2000 ZEETER Classic Part No.
デバイスDixon 10504-1101の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Dixon 10504-1101をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはDixon 10504-1101の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Dixon 10504-1101の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Dixon 10504-1101で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Dixon 10504-1101を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はDixon 10504-1101の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Dixon 10504-1101に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちDixon 10504-1101デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
