Dodgeメーカー2004 Intrepidの使用説明書/サービス説明書
ページ先へ移動 of 249
T ABLE OF CONTENTS SECTION P AGE 1 INTRODUCTION ............................................................. 3 2 THINGS TO KNOW BEFORE ST AR TING YOUR VEHICLE ........................... 7 3 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE ..............
.
INTRODUCTION CONTENTS 䡵 Introduction ........................... 4 䡵 How T o Use This Manual ................. 4 䡵 W arnings And Cautions .......
INTRODUCTION This manual has been prepar ed with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your new vehicle. It is supplemented by a W arranty Information Booklet and various customer oriented documents.
INTRODUCTION 5 1.
W ARNINGS AND CAUTIONS This manual contains W ARNINGS against operating procedur es which could result in an accident or bodily injury . It also contains CAUTIONS against procedures which could result in damage to your vehicle. If you do not read this entir e manual you may miss important information.
THINGS T O KNOW BEFORE ST ARTING YOUR VEHICLE CONTENTS 䡵 A W ord About Y our Keys ................. 9 ▫ Sentry Key Engine Immobilizer— If Equipped . . 9 ▫ Ignition Key Removal ................... 1 2 ▫ Key-In-Ignition Reminder ..............
▫ T o Program Additional T ransmitters ......... 2 0 ▫ T ransmitter Linked T o Memory Programming . . 21 ▫ General Information .................... 2 2 ▫ T ransmitter Battery Service ............... 2 2 䡵 Security Alarm System— If Equipped .
A WORD ABOUT YOUR KEYS Y ou can insert the double sided keys into the locks with either side up. The dealer that sold you your new vehicle has the key code numbers for your vehicle locks. These numbers can be used to order duplicate keys fr om your dealer or a locksmith.
If the Sentry Key Immobilizer System indicator light comes on during normal vehicle operation (it has been running for longer than 10 seconds) a fault has been detected in the electronics and the vehicle should be serviced as soon as possible. NOTE: • The Sentry Immobilizer System is not compatible with remote starting systems.
At the time of purchase, the original owner is pr ovided with a four digit PIN number . This number is requir ed for dealer replacement of keys. Duplication of keys may be performed at an authorized dealer or by using the Customer Key Programming pr ocedure.
2. this device must accept any interference that may be received, including interfer ence that may cause undes- ired operation Ignition Key Removal Place the shift lever in Park and make sure that the shift knob push-button (vehicles with floor shift) is in the out position.
Floor Shift Ignition Interlock System — If Equipped This system prevents the key fr om being removed unless the shift lever is in P ARK and the shift knob push button is out. It also prevents shifting out of P ARK unless the key is in the OFF or RUN positions.
GLOVE COMP ARTMENT LOCK The glove box lock has been designed so that the key can be inserted only about half way . Do not force the key past this point. ILLUMINA TED ENTR Y SYSTEM — IF EQUIPPED The interior lights will come on when you unlock the vehicle with the remote keyless entry (if so equipped) or central unlock (if so equipped).
If you press the door lock switch while the keys ar e in the ignition switch, with the ignition switch in the ACC, LOCK, or OFF position, and the driver’s door is open, the doors will not lock.
“Child-Protection” Lock System (Rear Doors) T o provide a safer envir onment for small children riding in the rear seat, the r ear doors of your vehicle have the “child-protection” door lock system.
3. vehicle speed is above 15 m.p.h. (24 km/h), 4. the accelerator pedal is depressed. The Automatic Door Locks can be disabled or re-enabled by performing the same following procedur e: 1. Close all doors and place the key in the ignition. 2. Cycle the ignition switch between OFF and ON/RUN and back to OFF 4 times ending up in the OFF position.
1. Close all doors and place the key in the ignition. 2. Cycle the ignition switch between ON/RUN and OFF 4 times ending up in the OFF position. 3. Depress the power door unlock switch to unlock the doors. 4. A single chime will indicate the completion of the programming.
Enable/Disable Lamp Flash: The Lamp Flash can be enabled or disabled by perform- ing the following procedur e: 1. Press and hold the Lock button on the transmitter . 2. Continue to hold the Lock button, wait at least 4 but no longer than 10 seconds, then press the T runk button.
T o Use The Panic Alarm: Press and hold the Panic button to activate the alarm. Press and hold the Panic button or unlock the door with the key to deactivate the alarm. The alarm will also shut itself off after 3 minutes or when vehicle speed r eaches 15 m.
will hear a chime after each transmitter has been success- fully programmed. Y ou will have 30 seconds to finish programming all new transmitters. A chime will sound when the 30 seconds is over or the ignition switch is turned to the Lock position.
General Information This transmitter complies with FCC rules part 15 and with RS-210 of Industry Canada. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) This device must accept any interference that may be r eceived, including interference that may cause undesir ed operation.
SECURITY ALARM SYSTEM— IF EQUIPPED The system monitors the doors, trunk key cylinder , and ignition for unauthorized operation. If something triggers the alarm, the system will signal for up to 18 minutes. For the first 3 minutes the horn will sound and the headlights, park and tail lights and the SET light will flash.
3. The SET light on the top of the instrument panel will flash rapidly for 16 seconds. This shows that the system is arming. If the light comes on but does not flash, the system is still armed, but there is a pr oblem in the trunk circuit. After 16 seconds the SET light will continue to flash slowly .
POWER WINDOWS W indow controls on the driver’s door control all door windows. The driver’s window switch has an Auto Down feature. Press the window switch past the detent, r elease, and the window will go down automatically . Press the switch a second time in either direction to stop the window .
TRUNK SAFETY W ARNING W ARNING! Do not allow children to have access to the trunk, either by climbing into the trunk from outside, or through the inside of the vehicle. Always close the trunk lid when your vehicle is unattended. Once in the trunk, young children may not be able to escape, even if they entered through the rear seat.
Please pay close attention to the information in this section. It tells you how to use your restraint system properly to keep you and your passengers as safe as possible. W ARNING! In a collision, you and your passengers can suffer much greater injuries if you are not properly buck- led up.
W ARNING! • W earing a seat belt incorrectly is dangerous. Seat belts are designed to go around the large bones of your body . These are the strongest parts of your body and can take the forces of a collision the best. W earing your belt in the wrong place could make your injuries in a collision much worse.
2. The seat belt latch plate is above the back of your seat. Grasp the latch plate and pull out the belt. Slide the latch plate up the webbing as far as necessary to allow the belt go around your lap. 3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a ”click.
4. Position the lap belt across your thighs, below your abdomen. T o remove slack in the lap belt portion, pull up a bit on the shoulder belt, as shown. T o loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt. A snug belt r educes the risk of sliding under the belt in a collision.
W ARNING! A frayed or torn belt could rip apart in a collision and leave you with no protection. Inspect the belt system periodically , checking for cuts, frays, or loose parts. Damaged parts must be replaced immediately . Do not disassemble or modify the system.
Seat Belts and Pregnant Women W e recommend that pr egnant women use the seat belts throughout their pr egnancy . Keeping the mother safe is the best way to keep the baby safe. Pregnant women should wear the lap part of the belt across the thighs and as snug acr oss the hips as possible.
Driver and Right Front Passenger Supplemental Restraint System (SRS) - Airbag This vehicle has front airbags for both the driver and front passenger as a supplement to the seat belt r estraint systems. The driver’s front airbag is mounted in the center of the steering wheel.
W ARNING! • Do not put anything on or around the front airbag covers or attempt to manually open them. Y ou may damage the airbags and you could be injured because the airbags are not there to protect you. These protective covers are designed to open only when the airbags are inflated.
be secured in the r ear seat in child restraints or belt- positioning booster seats appropriate for the size and age of the child. Older children who do not use child r estraints or belt- positioning booster seats should ride properly buckled up in the rear seat.
Airbag System Components The airbag system consists of the following: • ACM (Airbag Control Module) • AIRBAG Readiness Light • Driver and Passenger Front Airbags • Optional Driver and Passenger Side Airbags.
then turns the light off. If it detects a malfunction in any part of the system, it turns on the light either momentarily or continuously . W ARNING! Ignoring the AIRBAG light in your instrument panel could mean you won’t have the airbags to protect you in a collision.
floor . They are not caused by contact with chemicals. They are not permanent and normally heal quickly . However , if you haven’t healed significantly within a few days, or if you have any blistering, see your doctor immediately . • As the airbags deflate you may see some smoke-like particles.
• The side impact airbag control module monitors the readiness of the electr onic parts of the system when- ever the ignition switch is in the “ST AR T” or “RUN” positions. These include all of the items listed above except for the AIRBAG light (which is controlled by the frontal airbag system).
Airbag Light Y ou will want to have the airbags ready for your protection in an impact. While the airbag system is designed to be maintenance free, if any of the following occurs, have an authorized dealer service the system immediately .
Infants and Child Restraints • Safety experts recommend that childr en ride rearwar d-facing in the vehicle until they are at least one year old and weigh at least 20 lbs (9 kg). T wo types of child restraints can be used r earward-facing: infant carriers and “convertible” child seats.
Standards. W e also recommend that you try a child restraint in the vehicle seats wher e you will use it before you buy it. • The restraint must be appr opriate for your child’s weight and height. Check the label on the restraint for weight and height limits.
Children T oo Large For Booster Seats Children who ar e large enough to wear the shoulder belt comfortably , and whose legs are long enough to bend over the front of the seat when their back is against the seatback, should use the lap/shoulder belt in the rear seat.
Installing the LA TCH-Compatible Child Restraint System W e urge that you car efully follow the directions of the manufacturer when installing your child r estraint. Not all child restraint systems will be installed as described her e. Again, carefully follow the installation instr uctions that were pr ovided with the child restraint system.
the anchorage, being careful to r oute the tether strap to provide the most dir ect path between the anchor and the child restraint. If your vehicle is equipped with adjust- able rear head r estraints, raise the head restraint and, where possible, r oute the tether strap under the head restraint and between the two posts.
plate into the buckle again. If you still can’t make the child restraint secur e, try a differ ent seating position. T o attach a child restraint tether strap: 1. Lift the cover over the anchor directly behind the seat where you ar e placing the child restraint.
Pets should be restrained in the r ear seat in pet harnesses or pet carriers that are secur ed by seat belts. ENGINE BREAK-IN RECOMMENDA TIONS The engine in your new vehicle does not requir e a long break-in period. Drive moderately during the first 300 miles (500 km).
• T o avoid drawing exhaust gases into the vehicle, close the trunk while driving. However , if for some reason it must remain open, close all windows. Adjust the heating or cooling system to force outside air into the vehicle. Set the blower at high speed.
UNDERST ANDING THE FEA TURES OF YOUR VEHICLE CONTENTS 䡵 Cup Holders .......................... 5 2 ▫ Front Seat Cupholders ................... 5 2 䡵 Coat Hook ............................ 5 2 䡵 Mirrors .............................. 5 3 ▫ Adjusting The Inside Day/Night Mirror .
䡵 Exterior Lights ......................... 6 2 ▫ Headlights And Parking Lights ............ 6 2 ▫ Lights-On Reminder .................... 6 2 ▫ Headlight T ime Delay ................... 6 2 ▫ Battery Saver Feature—Exterior Lights ....... 6 3 ▫ Fog Lights .
䡵 Power Sun Roof — If Equipped ............ 7 6 ▫ W ind Buffeting ........................ 7 7 ▫ Sun Roof Maintenance ................... 7 7 䡵 Overhead T ravel Information Center — If Equipped ............................. 7 7 ▫ US/M Button .
CUP HOLDERS Front Seat Cupholders The cupholders for the 50/50 bench seat are located in the arm rest. raise the arm r est cover and fold the cupholders forward. The molded cupholders for the bucket seat are located in the forward edge of the center console.
MIRRORS Adjusting The Inside Day/Night Mirror Adjust the mirror to center on the view thr ough the rear window . A two point pivot system allows for horizontal and vertical mirror adjustment. Annoying headlight glare can be r educed by moving the small control under the mirr or to the night position (toward r ear of vehicle).
Electric Remote Control Mirrors Press the L or R button located on the driver’s door panel for Left or Right mirror selection. T ilt the mirror control up or down, or side to side to adjust the view in the mirror . NOTE: Place the mirror switch in the neutral position to prevent accidental changing of the mirr or setting.
Illuminated V anity Mirrors — If Equipped An illuminated vanity mirror is on each sun visor . T o use the mirror , rotate the sun visor down and swing the mirror cover upwar d. The lamps turn on automatically . Closing the mirror cover turns of f the lamps.
Power Seats — If Equipped The power seat switch is on the outboard side of the driver’s seat near the floor . Use this switch to move the seat up or down, forward or r earward, or to tilt the seat. The passenger’s seat will move forward or r earward.
W ARNING! Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt and be seriously or even fatally injured. Use the recliner only when the vehicle is parked.
The head restraints have a locking button which must be pushed in to lower the head restraint. The r estraints may be raised without pushing in the button. Folding Rear Seats — If Equipped T o provide additional storage ar ea, the rear seatbacks can be folded forward.
W ARNING! The cargo area in the rear of the vehicle (with the rear seatbacks in the locked-up or folded down position) should not be used as a play area by children when the vehicle is in motion. They could be seriously injured in an accident. Children should be seated and using the proper restraint system.
Then lift up on the catch located under the front edge of the hood, near the center . T o prevent possible damage, do not slam the hood to close it. Use a firm downward push at the center of the hood to ensure that both latches engage. Never drive your vehicle unless the hood is fully closed, with both latches engaged.
NOTE: The Battery Saver Feature will not turn these lights off if a switch was used to turn them on. Instrument Panel Lighting The brightness of the instrument panel lighting can be regulated by r otating the dimmer switch. Daytime Brightness Feature Certain instrument panel components can be illuminated at full brightness during the daytime.
EXTERIOR LIGHTS Headlights And Parking Lights When the headlight switch is turned clockwise from Of f to the first position, the parking lights, taillights, side marker lights, license plate light and instrument panel lights ar e all turned on. The headlights turn on when the switch is turned to the second position.
T o activate the delay , turn off the ignition while the headlights are still on. Then turn of f the headlights within 45 seconds. The delay interval begins when the ignition is turned off. If the headlights are turned of f before the ignition, they will go off in the normal manner .
T urn Signals The arrows on each side of the instr ument cluster flash to show operation of the front and r ear turn signal lights. If either light flashes at an extremely fast rate, check for a defective outside light bulb.
W ARNING! Sudden loss of visibility through the windshield could lead to an accident. Y ou might not see other vehicles or other obstacles. T o avoid sudden icing of the windshield during freezing weather , warm the windshield with the defroster before and during windshield washer use.
W ARNING! T ilting the steering column while the vehicle is moving is dangerous. W ithout a stable steering col- umn, you could lose control of the vehicle and have an accident. Adjust the column only while the ve- hicle is stopped. Be sure it is locked before driving.
ELECTRONIC SPEED CONTROL This device can be engaged to take over the accelerator operation at speeds between 30 mph (48 km/h) and 85 mph (137 km/h). The controls ar e mounted on the steering wheel. T o Activate: Push the ON/OFF button to turn the system ON.
T o Set At A Desired Speed: When the vehicle has reached the desir ed speed, and the system is activated, press and r elease the SET button. Release the accelerator and the vehicle will operate at the selected speed.
W ARNING! Speed Control can be dangerous where the system can’t maintain a constant speed. Y our vehicle could go too fast for the conditions, and you could lose control. An accident could be the result. Don’t use Speed Control in heavy traffic or on roads that are winding, icy , snow-covered, or slippery .
OVERHEAD CONSOLE The overhead console contains dome/r eading lights, an optional universal garage door opener (HomeLink 威 ), an optional sunroof switch, and an optional Over head T ravel Information System (OTIS). Dome/Reading Lights Located in the overhead console ar e two dome/reading lights.
For additional information on HomeLink 威 , call 1–800–355–3515, or on the internet at www .homelink.com. W ARNING! A moving garage door can cause injury to people and pets in the path of the door . People or pets could be seriously or fatally injured.
W ARNING! V ehicle exhaust contains carbon monoxide, a danger- ous gas. Do not run the vehicle’s exhaust while training the transceiver . Exhaust gas can cause seri- ous injury or death. W ARNING! Y our motorized door or gate will open and close while you are training the universal transceiver .
NOTE: Some entry gates and garage door openers may requir e you to replace step 4 with the procedur es listed under Canadian Programming. 5. The indicator light in the Universal T ransceiver will begin to flash, first slowly and then rapidly . The rapid flashing indicates successful programming.
1. Locate the training button on the garage door motor head unit. The exact location and color of the button may vary by garage door opener manufacturer . If you have difficulty in locating the training button, check your garage door opener manual, or call 1-800-355-3515 or , on the Internet, at www .
Reprogramming A Single Button 1. Press and hold the Universal T ransceiver button to be repr ogrammed. Do not release until step 4 has been completed. 2. When the indicator light begins to flash slowly (after 20 seconds) position the hand held transmitter 1 to 3 inches (3 to 8 cm) away from the button to be trained.
POWER SUN ROOF — IF EQUIPPED The sun roof contr ols are located on the overhead con- sole. T o Open the sunroof fr om the Closed position, press and release the OPEN button. The sunr oof will open fully , then stop automatically . T o Close the sunroof fr om an open or vent position, press and hold the CLOSE button.
Wind Buffeting W ind buffeting can be described as the perception of pressur e on the ears or a helicopter type sound in the ears. Y our vehicle may exhibit wind buffeting with the windows down, or the sunroof (if so equipped) in certain open or partially open positions.
US/M Button Use this button to change the display from U.S. to metric measurement units. RESET Button Use this button to reset the following displays to zer o: A verage Fuel Economy T rip Odometer Elapsed time.
Compass/T emperature Display This display provides the outside temperatur e and one of eight compass readings to indicate the dir ection the vehicle is facing. Automatic Compass Calibration The self calibrating feature of the compass eliminates the need to calibrate the compass for normal conditions.
V ariance is the differ ence between magnetic North and geographic North. For proper compass function, the correct variance zone must be set. Refer to the variance map for the correct variance zone. T o check the variance zone, the ignition must be on and the compass/ temperature displayed.
Outside T emperature Because engine temperature can incr ease the displayed temperature, temperatur e readings are slowly updated when vehicle speed is below 20 MPH (30 km/h).
.
UNDERST ANDING YOUR INSTRUMENT P ANEL CONTENTS 䡵 Instruments And Controls ................. 8 6 䡵 Instrument Cluster ...................... 8 7 䡵 Instrument Cluster Description ............. 8 8 䡵 Electronic Digital Clock .................. 9 3 ▫ T o Set The Clock .
▫ T ape Eject ............................ 9 7 ▫ Scan Button .......................... 9 7 ▫ Changing T ape Direction ................. 9 7 ▫ Metal T ape Selection .................... 9 7 ▫ Pinch Roller Release .................... 9 7 ▫ Noise Reduction .
▫ Radio Display Messages ................ 1 0 5 䡵 Sales Code RBK—AM/ FM Stereo Radio W ith CD Player And CD Changer Contr ols ... 1 0 5 ▫ Radio Operation ...................... 1 0 5 ▫ CD Player Operation ................... 1 0 7 ▫ CD Changer Operation — If Equipped .
INSTRUMENTS AND CONTROLS 86 UNDERST ANDING YOUR INSTRUMENT P ANEL.
Instrument Cluster UNDERST ANDING YOUR INSTRUMENT P ANEL 87 4.
INSTRUMENT CLUSTER DESCRIPTION 1. Fuel Gauge When the ignition is in the ON position, the pointer will show the level of fuel remaining in the tank. 2. Low Fuel W arning Light When the fuel level drops to about 2 gallons (8 liters), the Low Fuel symbol will light and re- main lit until fuel is added.
7. T urn Signal Indicators The arrow will flash in unison with the exterior turn signal, when using the turn signal lever . 8. High Beam Indicator This light shows that the headlights are on high beam. Pull the turn signal lever towards the steering wheel to switch the headlights from high or low beam.
If the pointer rises to the “H” mark, stop the vehicle and turn off the engine until the pr oblem is corrected. CAUTION! Continuing to drive with an overheated engine cool- ing system can cause damage to the engine or other components. There ar e steps that you can take to slow down an impending overheat condition.
have it replaced. If the light stays on, or comes on while driving, have the system checked by an autho- rized dealer . 19. Odometer/T rip Odometer Shows the total distance the vehicle has been driven.
If the ABS light is on, the brake system should be serviced as soon as possible to restor e the benefits of Anti-Lock brakes. 23. Brake System W arning Light The dual brake system provides a r eserve braking capability if a failure occurs in a portion of the hydraulic system.
ELECTRONIC DIGIT AL CLOCK The clock and radio each use the display panel built into the radio. A digital readout indicates the time in hours and minutes whenever the ignition switch is in the ON or ACC position.
Seek Button (Radio Mode) Press and r elease the Seek button to search for the next station in either the AM or FM mode. Pr ess the top of the button to seek up and the bottom to seek down. Holding the button will by pass stations until you release the button.
Program T ype Radio Display Soft Rhythm and Blues Soft R&B Sports Sports T alk T alk T op 40 T op 40 W eather W eather By pressing the SEEK button when the PTY icon is displayed, the radio will be tuned to the next frequency station with the same selected PTY name.
AM/FM Selection Press the AM/FM button to change from AM to FM. The operating mode will be displayed next to the station frequency . The display will show ST when a stereo station is received.
be experienced due to a defective cassette tape. Clean and demagnetize the tape heads at least twice a year . Seek Button Press the SEEK button up for the next selection on the tape and down to return to the beginning of the curr ent selection. Press the SEEK button up or down to move the track number to skip forward or backwar d 1 to 6 selections.
Noise Reduction The Dolby Noise Reduction System* is on whenever the tape player is on, but may be switched off. T o turn off the Dolby Noise r eduction System: Press the Dolby button (button 2) after you insert the tape. The NR light in the display will go off when the Dolby System is off.
EJT CD (Eject) Button Press this button and the disc will unload and move to the entrance for easy removal. The unit will switch to the radio mode. If you do not remove the disc within 15 seconds, it will be reloaded. The radio mode will continue to appear .
T ape CD Button Press this button to select between CD player and T ape player . Time Button Press this button to change the display fr om elapsed CD playing time to time of day . Scan Button Press this button to play the first 10 seconds of each track.
For your convenience, the volume can be turned down, but not up, when the audio system is off and the ignition is ON. Seek Press and r elease the SEEK button to search for the next station in either the AM or FM mode. Pr ess the top of the button to seek up and the bottom to seek down.
Bass and T reble T one Control The tone controls consist of 2 separate bands. The bass band is on the left, and the treble band is on the right. Each band is adjusted by a slider control with a detent at the mid-position. Moving the control up or down in- creases or decr eases amplification of that band.
Selective Music Search Press the SEEK button up or down to move the track number to skip forward or backwar d 1 to 7 selections. Press the SEEK button once to move 1 selection, twice to move 2 selections, etc.
Seek Button Press the SEEK up or down to select another track on the same disc. A SEEK symbol will appear on the display . Fast Forward And Rewind Buttons Press and hold the FF button for fast forwar d. Press and hold the R W button for fast reverse. The audio output can be heard when fast forwar d and fast reverse ar e activated.
Radio Display Messages Y our radio has been designed to display certain messages when a problem is detected with the CD player . SALES CODE RBK—AM/ FM STEREO RADIO WITH CD PLA YER AND CD CHANGER CONTROLS Radio Operation Power/V olume Control Press the ON/VOL contr ol to turn the radio on.
Seek Press and r elease the SEEK button to search for the next station in either the AM or FM mode. Pr ess the top of the button to seek up and the bottom to seek down. The radio will remain tuned to the new station until you make another selection. Holding the button in will by- pass stations without stopping until you release it.
Y ou may add a second station to each push-button by repeating the above pr ocedure with this exception: Press the SET button twice and SET 2 will show in the display window . Each button can be set for SET 1 and SET 2 in both AM and FM. This allows a total of 10 AM and 10 FM stations to be locked into push-button memory .
display will show the track number and index time in minutes and seconds. Play will begin at the start of track one. Seek Press the top of the SEEK button for the next selection on the CD.
CD Changer Operation — If Equipped MODE Press the MODE button to select between the cassette tape player , CD player , and the CD changer (if equipped).
6 DISC CD CHANGER — IF EQUIPPED The CD changer is located below the radio in the instrument panel. The changer plays only 4 3 ⁄ 4 inch (12 cm) discs. The changer holds up to 6 discs. Each disc is loaded and ejected through a single slot in fr ont of the changer .
Playing Discs The radio will show the CD number , the CD track number , and the T rack T ime Elapsed while the radio is in the CD mode. If more than one CD is loaded in the changer , the changer will automatically play the next disc after playing the last track of the current disc.
Time Button Press this button to switch between time of day and CD track time. Changing Modes While in the radio mode, if a cassette is loaded, press the Mode button to switch to the tape mode. If a CD is loaded, press the Mode button to select the CD mode.
5. A loose tape should be corrected befor e use. T o rewind a loose tape, insert the eraser end of a pencil into the tape drive gear and twist the pencil in the requir ed directions. Maintain your cassette tape player . The head and capstan shaft in the cassette player can pick up dirt or tape deposits each time a cassette is played.
RADIO OPERA TION AND CELLULAR PHONES Under certain conditions, the operation of a cellular phone in your vehicle can cause erratic or noisy perfor- mance from your radio. This condition may be lessened or eliminated by relocating the cellular phone antenna.
to the O (Off) position to shut of f the fan and to prevent any outside air from entering the vehicle. This also turns off the A/C compressor . T emperature Control Use this control to r egulate the temperature of the air inside the passenger compartment.
The warmer air goes to the floor outlets. This feature provides impr oved comfort during sunny but cool con- ditions. Floor Air is directed thr ough the floor outlets with a lesser amount through the defr ost and side win- dow demist outlets. Mix Air is directed thr ough the floor , defrost, and side window demist outlets.
NOTE: If your air conditioning performance seems lower than expected, check the front of the A/C con- denser for an accumulation of dirt or insects. Clean with a gentle water spray from behind the radiator and through the condenser as r equired.
Y ou also may choose to customize your comfort by selecting the fan speed and Mode. This will place the system into manual operation Interior A TC Sensors There ar e two interior sensors in the vehicle. The Sun Sensor is mounted in the center of the instrument panel near the windshield glass.
Comfort Control Use this control to r egulate the comfort inside the pas- senger compartment. Press the top of the switch to raise the temperature selection and the bottom of the switch to lower it. The comfort setting range is from Lo, 60, 61,....to 89,90, Hi, for automatic temperature contr ol.
NOTE: The Recirc button light will blink if you try to use it in the Mix or Defrost modes. Air Direction Buttons (Mode) These buttons allow you to select from five air distribu- tion patterns. These buttons should be used only when you can not achieve comfort or visibility in Auto opera- tion.
NOTE: The air conditioning compressor is on in this mode. This dehumidifies the air to help dry the wind- shield. T o improve fuel economy , leave in the defrost mode only when necessary . Rear W indow Defroster Press the button once to turn on the Rear W indow Defroster and a second time to turn it of f.
Side W indow Demisters Side window demisters are located on the instr ument panel. These non adjustable outlets direct air towar d the side windows in any mode except Panel or Panel Recir- culation. The air is directed towar d the area of the side windows through which you view the outside r earview mirrors.
Operating T ips (Manual A/C and A TC) UNDERST ANDING YOUR INSTRUMENT P ANEL 123 4.
Outside Air Intake Make sure that the air intake dir ectly in front of the windshield is free of obstr uctions. Leaves, snow , etc., could block air flow into the vehicle.
ST ARTING AND OPERA TING CONTENTS 䡵 Starting Procedur es .................... 1 2 7 ▫ Normal Starting ...................... 1 2 7 ▫ Extremely Cold W eather (Below -20°F Or -29°C) ................. 1 2 7 ▫ If Engine Fails T o Start .........
▫ T ire Chains .......................... 1 4 0 ▫ Snow T ires .......................... 1 4 0 ▫ T read W ear Indicators .................. 1 4 1 ▫ Replacement T ires ..................... 1 4 1 ▫ T ire Rotation Recommendations ........... 1 4 2 ▫ Alignment And Balance .
ST ARTING PROCEDURES W ARNING! Do not leave children or animals inside parked vehicles in hot weather . Interior heat build up may cause serious injury or death. The gear selector must be in the NEUTRAL or P ARK position before you can start the engine.
If Engine Fails T o Start CAUTION! Do not try to push or tow your vehicle to get it started. Y our vehicle cannot be started this way . Pushing with another vehicle may damage the trans- axle or the rear of your vehicle. See Section 6 of this manual for the proper jump starting procedures.
After Starting The idle speed will automatically decrease as the engine warms up. At cooler ambient temperatures, the idle speed for the 2.7L engine may incr ease during extended idles for improved heater performance. ENGINE BLOCK HEA TER — Optional U.
T ransaxle Reset Mode The transaxle is monitored for abnormal conditions. If a condition is detected that could cause damage, the trans- axle automatically shifts into second gear . The transaxle remains in second gear despite the forwar d gear selected.
W ARNING! Never use the Park position as a substitute for the parking brake. Always apply the parking brake fully when parked to guard against vehicle movement and possible injury or damage. “R” Reverse Shift into this range only after the vehicle has come to a complete stop.
“L” Low This range should be used for maximum engine braking when descending steep grades. In this range, up-shifts will occur only to prevent engine over speed while down shifts occur as early as possible. P ARKING BRAKE When the parking brake is applied with the ignition on, the red Brake light in the instr ument cluster will come on.
When parking on a hill, you must set the parking brake before placing the gear selector in Park. If you don’t, the load on the transmission locking mechanism may make it difficult to move the selector out of Park. As an added precaution, turn the fr ont wheels toward the curb on a downhill grade and away from the curb on an uphill grade.
BRAKE SYSTEM Y our vehicle is equipped with power brakes as standard equipment. In the event you lose power assist for any reason (for example, r epeated brake applications with the engine off), the brakes will still function.
All vehicle wheels and tires must be the same size and tires must be pr operly inflated to produce accurate signals for the ABS computer . However , the system will compensate when the compact spare is in use. During stops where ABS is activated, a vibration of the brake pedal may be felt and associated system noises may be heard.
• The system has been deactivated to prevent damage to the brake system due to overheated brake temperatur es. NOTE: Extended heavy use of T raction Control may cause the system to deactivate and turn on the T raction Control OFF Light, indicated by TRAC OFF , located in the instrument cluster .
2. Economy— Improper inflation pr essures can cause uneven wear patterns to develop across the tir e tread. These abnormal wear patterns will reduce tr ead life resulting in a need for earlier tire r eplacement. Under inflation also increases tire r olling resistance and results in higher fuel consump- tion.
period. The cold inflation pressur e must not exceed the maximum values molded into the tire side wall. T ire pressur e may increase from 2 to 6 psi [.13 to.41 bars](14 to 41 kPa) during operation. Do NOT reduce this normal pressur e build up or your tire pressur e will be too low .
Compact Spare Tire Maintain the compact spare tir e inflation pressure at 60 psi [4.1 bars](414 kPa). Do not exceed 50 mph (80 km/h) while the compact spare is installed on the vehicle. Do not install a wheel cover or attempt to mount a conventional tire on the compact spar e wheel, since the wheel is designed specifically for the compact spare.
Tire Spinning When stuck in mud, sand, snow , or ice conditions, do not spin your vehicle’s wheels above 30 mph. (48 km/h). See the paragraph on Freeing A Stuck V ehicle in section 6 of this manual. W ARNING! Fast spinning tires can be dangerous. Forces gener- ated by excessive wheel speeds may cause tire dam- age or failure.
T read Wear Indicators T read wear indicators ar e in the original equipment tires to help you in determining when your tires should be replaced. These indicators are molded into the bottom of the tr ead grooves and will appear as bands when the tr ead depth becomes 1/16 inch (2 mm).
W ARNING! • Do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change sus- pension dimensions and performance characteris- tics, resulting in changes to steering, handling, and braking of your vehicle.
Rotate your tires at intervals shown on the maintenance schedules. More fr equent rotation is permissible if de- sired. The r easons for any rapid or unusual wear should be corrected befor e rotating. The suggested rotation method is the “forwar d-cross” shown in the diagram.
Light spark knock at low engine speeds is not harmful to your engine. However , continued heavy spark knock at high speeds can cause damage and should be reported to your dealer immediately . Engine damage resulting from operating with a heavy spark knock may not be covered by the new vehicle warranty .
CAUTION! DO NOT use gasolines containing Methanol. Use of these blends may result in starting and driveability problems and may damage critical fuel system com- ponents. Problems that r esult from using methanol/gasoline blends are not the r esponsibility of the manufacturer and may not be covered by the vehicle warranty .
unleaded gasoline having lower sulfur to determine if the problem is fuel r elated prior to returning your vehicle to an authorized dealer for service. CAUTION! If the Malfunction Indicator Light is flashing, imme- diate service is required. See the On Board Diagnos- tics paragraph in the Maintenance section of this manual.
W ARNING! A fire may result if gasoline is pumped into a portable container that is inside of a vehicle. Y ou could be burned. Always place gas containers on the ground while filling. Fuel Filler Cap (Gas Cap) The gas cap is behind the fuel filler door , on the passen- ger’s side of the vehicle.
VEHICLE LOADING The load carrying capacity of your vehicle is shown in the following sample chart and on the tire pr essure label attached to the driver’s door . V ehicle Loading Capacities Front Seat Occupants .................... 2 o r 3 Rear Seat Occupants .
NOTE: Using the “3” range while operating the vehicle under heavy operating conditions will improve perfor - mance and extend transaxle life by reducing excessive shifting and heat build up. • For vehicles equipped with autostick, by using the autostick mode, and selecting a specific gear range, frequent shifting can be avoided.
.
WHA T T O DO IN EMERGENCIES CONTENTS 䡵 Hazard W arning Flasher ................. 1 5 2 䡵 If Y our Engine Overheats ................ 1 5 2 䡵 Jacking And T ire Changing ............... 1 5 3 ▫ Preparations For Jacking ................ 1 5 4 ▫ Jacking And Changing a T ire .
HAZARD W ARNING FLASHER The flasher switch is on the steering column, just behind the steering wheel. Push in the flasher switch and all front and r ear directional signals will flash. Press the flasher switch a second time to turn the flashers off. Do not use this emergency warning system when the vehicle is in motion.
the fan control to High. This allows the heater cor e to act as a supplement to the radiator and aids in removing heat from the engine cooling system. CAUTION! Driving with a hot cooling system could damage your vehicle. If temperature gauge reads “H”, pull over and stop the vehicle.
Preparations For Jacking • T urn on the Hazard W arning Flashers and park the vehicle on a firm level surface, avoiding ice or slippery areas. • Put the gear shift in P ARK (Automatic transmission) or REVERSE (Manual T ransmission). • Set the parking brake and turn off the engine.
2. Remove the spare tir e, scissors, jack and lug wrench. 3. Before raising the vehicle, use the lug wr ench to loosen the lug nuts of the flat tire. 4. T urn the jack screw clockwise to firmly engage the jack saddle with the lift area of the sill flange, use the lift ar ea closest to the flat tire.
5. Raise the vehicle just enough to remove the flat tir e and install the spare tir e. 6. Remove the lug nuts, wheel cover (if equipped) and tire. Remove the cover by hand, do not pry of f. 7. Mount the spare tir e. For vehicles equipped with wheel covers, see the wheel cover installation instruc- tions.
1 1. Store the flat tir e, jack and tools. W ARNING! Raising the vehicle higher than necessary can make the vehicle less stable. It could slip off the jack and hurt someone near it.
3. Install the cover by hand, snapping the cover over the two lug nuts. Do not use a hammer or excessive force to install the cover . 4. Return to Changing a T ire Section, Item #8 above. JUMP-ST ARTING THE BA TTER Y W ARNING! T ake care to avoid the radiator cooling fan whenever the hood is raised.
W ARNING! Battery fluid is a corrosive acid solution; do not allow battery fluid to contact eyes, skin or clothing. Don’t lean over battery when attaching clamps or allow the clamps to touch each other . If acid splashes in eyes or on skin, flush the contaminated area immediately with large quantities of water .
Check the Battery T est Indicator . If a light or bright colored dot is visible in the indicator , DO NOT jump-start the battery . If the indicator is dark or shows a green dot, pr oceed as follows: 1. W ear eye protection and remove any metal jewelry such as watch bands or bracelets that might make an inadvertent electrical contact.
5. Connect the other cable, first to the negative jump start attachment of the booster battery and then to the engine of the vehicle with the discharged battery .
1. Slow down during rainstorms or when roads ar e slushy . 2. Slow down if road has standing water or puddles. 3. Replace tires when tr ead wear indicators first become visible. 4. Keep tires pr operly inflated. 5. Maintain sufficient distance between your vehicle and the vehicle in front of you to avoid a collision in a sudden stop.
TOWING A DISABLED VEHICLE Only two ways of towing are appr oved; front towing and flat bed towing. CAUTION! • Do not attempt to tow this vehicle from the front with sling type towing equipment. Damage to the front fascia will result. • Always use wheel lift equipment when towing from the front.
.
MAINT AINING YOUR VEHICLE CONTENTS 䡵 2.7L Engine .......................... 1 6 7 䡵 3.5L Engine .......................... 1 6 8 䡵 Onboard Diagnostic System (OBD II) ....... 1 6 9 䡵 Emissions Inspection And Maintenance Programs ...............
▫ Fuel System Hoses .................... 1 9 4 ▫ Automatic T ransaxle ................... 1 9 4 ▫ Appearance Care And Protection From Corrosion ........................... 1 9 7 䡵 Fuses ............................... 2 0 1 ▫ Fuse Block Relays .
2.7L ENGINE MAINT AINING YOUR VEHICLE 167 7.
3.5L ENGINE 168 MAINT AINING YOUR VEHICLE.
ONBOARD DIAGNOSTIC SYSTEM (OBD II) T o meet new government regulations and pr omote cleaner air , your vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transaxle control systems.
EMISSIONS INSPECTION AND MAINTENANCE PROGRAMS In some localities, it may be a legal requir ement to pass an inspection of your vehicle’s emissions control system.
If your OBD system is not ready , you should see your authorized dealer or repair facility . If your vehicle was recently serviced or had a battery failur e or replacement, you may need to do nothing more than drive your vehicle as you normally would in order for your OBD system to update.
W ARNING! Y ou can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the proper equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic.
The best time to check the oil level is about 5 minutes after a fully warmed up engine is shut off or befor e starting the engine after it has sat overnight.
Checking the oil while the vehicle is on level ground also will improve the accuracy of the oil level r eadings. Maintain the oil level between the MIN and MAX markings on the dipstick. Adding one quart of oil when the reading is at the MIN mark will r esult in a MAX reading on these engines.
• More than 50% of your driving is at sustained high speeds during hot weather above 90°F (32°C) • T railer towing • T axi, police, or delivery service (commercial operation) • Off r oad or .
American Petroleum Institute (API) Engine Oil Identification Symbol This symbol means that the oil has been certified by the American Petroleum Institute (API). W e only recommend API Certified en- gine oils that meet the requir e- ments of DaimlerChrysler’s Mate- rial Standard MS-6395.
The proper SAE viscosity grade of engine oil should be selected based on the following recommendations and be within the operating temperature shown in the engine oil viscosity charts. SAE 10W -30 oil is preferred for use in 3.5L engines within the operating temperatures shown in the viscosity chart.
on how and where used oil can be safely discar ded in your area. Engine Oil Filter The engine oil filter should be replaced at every engine oil change. Engine Oil Filter Selection All of this manufacturer’s engines have a full-flow type disposable oil filter .
Under normal operating conditions, the catalytic con- verter will not requir e maintenance. However , it is im- portant to seek service to assure pr oper catalyst operation and prevent possible catalyst damage. If the Malfunction Indicator light is flashing, immediate service is requir ed.
Engine T iming Belt Replace the engine timing belt at the intervals described in the appropriate maintenance schedule. Crankcase Emission Control System Proper operation of this system depends on fr eedom from sticking or plugging due to deposits. As vehicle mileage builds up, the PCV valve and passages may accumulate deposits.
Maintenance-Free Battery The top of the MAINTENANCE-FREE battery is perma- nently sealed. Y ou will never have to add water , nor is periodic maintenance requir ed. NOTE: The battery is stored in a compartment in fr ont of the tire in the right fr ont fender and is accessible through the engine compartment.
CAUTION! It is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post. Battery posts are marked positive (+) and negative (-) and identified on the battery case.
Power Steering Fluid Check W ARNING! Fluid level should be checked with the engine off to prevent injury from moving parts. Do not overfill. Use only manufacturer’s recommended power steer- ing fluid, refer to Recommended Fluids, Lubricants and Genuine Parts for the correct fluid type.
Chassis Lubrication Front Suspension Ball Joints Inspect these ball joints whenever your vehicle is ser- viced. They are permanently lubricated and do not requir e periodic lubrication. Steering Linkage Inspect tie rod ends whenever the vehicle is serviced.
Hood Latch When performing other under hood services, the hood latch release mechanism and safety catch should be inspected, cleaned, and lubricated. It is important to maintain proper lubrication to insur e that the hood mechanisms work properly and safely .
• T runk latches • Ash tray • Door Check Straps Windshield Wiper Blades Clean the rubber edges of the wiper blades and the windshield periodically with a sponge or soft cloth and a mild non abrasive cleaner . This will remove accumula- tions of salt or road film.
Exhaust System The best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust system. If you notice a change in the sound of the exhaust system; or if .
Cooling System W ARNING! • When working near the radiator cooling fan, dis- connect the fan motor lead or turn the ignition key to the OFF position. The fan is temperature con- trolled and can start at any time the ignition key is in the ON position.
coolant in open containers or allow it to remain in puddles on the ground. Pr event ingestion by animals or children. If ingested by a child, contact a physician immediately . Selection Of Coolant Use only the manufacturer’s r ecommended coolant. Re- fer to the Recommended Fluids, Lubricants and Genuine Parts section for the correct coolant type.
W ARNING! The warning words “DO NOT OPEN HOT” on the cooling system pressure cap are a safety precaution. Never add coolant when the engine is overheated. Do not loosen or remove the cap to cool an over- heated engine. Heat causes pressure to build up in the cooling system.
Points to Remember NOTE: When the vehicle is stopped after a few miles of operation, you may observe vapor coming from the fr ont of the engine compartment.
Pay particular attention to those hoses nearest to high heat sources such as the exhaust manifold. Inspect hose routing to be sur e hoses do not touch any heat source or moving component that may cause heat damage or mechanical wear . Insure nylon tubing in these ar eas has not melted or collapsed.
NOTE: Often, fluids such as oil, power steering fluid, and brake fluid are used during assembly plant operations to ease the assembly of hoses to couplings. Therefor e, oil wetness at the hose-coupling area is not necessarily an indication of leakage.
W ARNING! Use of a brake fluid that may have a lower initial boiling point or unidentified as to specification, may result in sudden brake failure during hard pro- longed braking. Y ou could have an accident. Use only brake fluid that has been in a tightly closed container to avoid contamination from for eign matter .
CAUTION! Using a transmission fluid other than the manufac- turer’s recommended fluid may cause deterioration in transmission shift quality and/or torque converter shudder . Using a transmission fluid other than that recommended by the manufacturer will result in more frequent fluid and filter changes.
Procedure For Checking Fluid Level T o properly check the automatic transaxle fluid level, the following procedur e must be used: • The vehicle must be on level ground. • The engine should be running at curb idle speed for a minimum of 60 seconds.
CAUTION! Do not overfill. Dirt and water in the transaxle can cause serious damage. T o prevent dirt and water from entering the transaxle after checking or replen- ishing fluid, make certain that the dipstick cap is seated properly .
The following maintenance recommendations will enable you to obtain maximum benefit from the corr osion resistance built into your vehicle. What Causes Corrosion? Corrosion is the r esult of deterioration or removal of paint and protective coatings fr om your vehicle.
• It is important that the drain holes in the lower edges of the doors, rocker panels and r ear deck lid be kept clear and open. • If you detect any stone chips or scratches in the paint, touch them up immediately . The cost of such repairs is considered the r esponsibility of the owner .
CAUTION! The use of vinyl, leather or plastic protectants may cause excessive gloss and/or discoloration of interior trim parts. Leather Seat Care and Cleaning Leather is best preserved by r egular cleaning with a damp soft cloth.
Cleaning Plastic Instrument Cluster Lenses The lenses in front of the instr uments in this vehicle are molded in clear plastic. When cleaning the lenses, care must be taken to avoid scratching the plastic. • Clean with a wet soft rag. A mild soap solution may be used, but do not use high alcohol content or abrasive cleaners.
Underhood Fuses A Power Distribution center is located in the engine compartment. This center contains fuses and relays for circuits that operate only under the hood. A label which identifies these components is located on the underside of the cover .
Cavity Fuse Circuits 8 10 Amp Red Airbag 9 10 Amp Red T urn Signal Lights, T urn Signal/Hazard Indicator 10 15 Amp Lt. Blue Right Low Beam 1 1 20 Amp Y ellow High Beam Relay , High Beam Indicator , High Beam Switch 12 15 Amp Lt.
REPLACEMENT BULBS Interior Light Bulbs Bulb No. Cluster Illumination ..................... PC194 T urn Signal ........................... PC194 Climate Control .......................... 3 3 0 Overhead Console, Fr ont Reading, Courtesy , Grab Handle .
4. Remove the bulb from the socket and r eplace the bulb. CAUTION! Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. If the bulb comes into contact with any oily surface, clean the bulbs with rubbing alcohol.
Fog Light 1. Remove the screw securing the fog light to the fascia and pull the light away from the vehicle to expose the bulb. 2. Remove the bulb by turning counter-clockwise. Pull the bulb out of the light housing. 3. Remove the wiring connector from the bulb.
T ail, Stop, Back Up, and T urn Signal Lights 1. Open the trunk and remove the fasteners securing the light housing to the body . 2. Pull the light housing from the body to expose the wiring socket. 3. T urn the bulb socket counterclockwise to remove fr om the housing.
SPECIFICA TIONS ENGINE ALL Oil Filter Mopar 5281090 or equivalent Thermostat 180°F (82°C) Spark Plug See Underhood Label Spark Plug Gap See Underhood Label Firing Order 1-2-3-4-5-6 FLUID CAP ACITIES U.S. Metric Fuel (Approximate) 17 Gallons 64 Liters Engine Oil with Filter 2.
RECOMMENDED FLUIDS, LUBRICANTS AND GENUINE P ARTS Engine Component Fluid, Lubricant or Genuine Part Engine Coolant Mopar 威 Antifreeze/Coolant 5 Y ear/100,000 Mile Formula HOA T (Hybrid Or- ganic Additive T echnology) Engine Oil Use API Certified (GF-3).
Body Component Fluid, Lubricant or Genuine Part Hinges: Door , Hood and T runk Mopar 威 Engine Oil Hood hinge springs and links Mopar 威 Spray White Lube Latches: Door and Hood T runk Mopar 威 Mult.
MAINTENANCE SCHEDULES CONTENTS 䡵 Emission Control System Maintenance ...... 2 1 2 䡵 Maintenance Schedules .................. 2 1 2 ▫ Schedule “B” .
EMISSION CONTROL SYSTEM MAINTENANCE The “Scheduled” maintenance services, listed in bold type must be done at the times or mileages specified to assure the continued pr oper functioning of the emission control system.
NOTE: If ANY of these apply to you then change your engine oil every 3,000 miles (5 000 km) or 3 months, whichever comes first and follow schedule “B” of the ⬙ Maintenance Schedules ⬙ section of this manual. NOTE: Most vehicles are operated under the conditions listed for Schedule ⬙ B ⬙ .
Once a Month • Check tire pr essure and look for unusual wear or damage. • Inspect the battery and clean and tighten the terminals as requir ed. • Check the fluid levels of coolant reservoir , brake master cylinder , power steering and transaxle and add as needed.
SCHEDULE “B” Follow schedule “B” if you usually operate your vehicle under one or more of the following conditions. Change the automatic transmission fluid and filter every 60,000 miles (96 000 km) if the vehicle is usually operated under one or more of the conditions marked with an 〫 .
Miles 3,000 6,000 9,000 12,000 15,000 18,000 (Kilometers) (5 000) (10 000) (14 000) (19 000) (24 000) (29 000) Change engine oil and engine oil filter . XXXXX X Inspect the air cleaner filter and replace if r e- quired.* XXXX X Replace the air cleaner filter .
Miles 21,000 24,000 27,000 30,000 33,000 36,000 (Kilometers) (34 000) (38 000) (43 000) (48 000) (53 000) (58 000) Change engine oil and engine oil filter . XXXXX X Inspect the air cleaner filter and replace if r e- quired.* XXX X X Replace the air cleaner filter .
Miles 39,000 42,000 45,000 48,000 51,000 54,000 (Kilometers) (62 000) (67 000) (72 000) (77 000) (82 000) (86 000) Change engine oil and engine oil filter . XXXXX X Inspect the air cleaner filter and replace if r e- quired.* XX XX X Replace the air cleaner filter .
Miles 57,000 60,000 63,000 66,000 69,000 72,000 (Kilometers) (91 000) (96 000) (101 000) (106 000) (1 10 000) (1 15 000) Change engine oil and engine oil filter . XXXXX X Inspect the air cleaner filter and replace if r e- quired.* X XXX X Replace the air cleaner filter .
Miles 75,000 78,000 81,000 84,000 87,000 90,000 (Kilometers) (120 000) (125 000) (130 000) (134 000) (139 000) (144 000) Change engine oil and engine oil filter . XXXXX X Inspect the air cleaner filter and replace if r e- quired.* XXXX Replace the air cleaner filter .
Miles 93,000 96,000 99,000 100,000 102,000 105,000 (Kilometers) (149 000) (154 000) (158 000) (160 000) (163 000) (168 000) Change engine oil and engine oil filter . X X X X X Inspect the air cleaner filter and replace if r e- quired.* XXX X Replace the air cleaner filter .
SCHEDULE “A” Miles 6,000 12,000 18,000 24,000 30,000 36,000 (Kilometers) (10 000) (19 000) (29 000) (38 000) (48 000) (58 000) [Months] [6] [12] [18] [24] [30] [36] Change engine oil and engine oil filter . X XXXXX Inspect the air cleaner filter and replace if r e- quired.
Miles 42,000 48,000 54,000 60,000 66,000 72,000 (Kilometers) (67 000) (77 000) (86 000) (96 000) (106 000) (1 15 000) [Months] [42] [48] [54] [60] [66] [72] Change engine oil and engine oil filter . X X XXXX Inspect the air cleaner filter and replace if requir ed.
Miles 78,000 84,000 90,000 96,000 102,000 (Kilometers) (125 000) (134 000) (144 000) (154 000) (163 000) [Months] [78] [84] [90] [96] [102] Change engine oil and engine oil filter . X X X X X Inspect the air cleaner filter and replace if r e- quired.* XX X X Replace the air cleaner filter .
W ARNING! Y ou can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent me- chanic.
.
IF YOU NEED CONSUMER ASSIST ANCE CONTENTS 䡵 Suggestions For Obtaining Service For Y our V ehicle .............................. 2 2 8 ▫ Prepar e For The Appointment ............ 2 2 8 ▫ Prepar e A List ........................ 2 2 8 ▫ Be Reasonable W ith Requests .
SUGGESTIONS FOR OBT AINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment If you’re having warranty work done, be sur e to have the right papers with you. T ake your warranty folder . All work to be performed may not be covered by the warranty , discuss additional charges with the service manager .
This is why you should always talk to your dealer’s service manager first. Most matters can be resolved with this process. • If for some reason you ar e still not satisfied, talk to the general manager or owner of the dealership. They want to know if you need assistance.
Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) T o assist customers who have hearing difficulties, the manufacturer has installed special TDD (T elecommuni- cation Devices for the Deaf) equipment at its Customer Center .
W ARRANTY INFORMA TION See your manufacturer’s W arranty Information Booklet for information on warranty coverage and transfer of warranty . MOP AR 姞 P ARTS Mopar 威 fluids, lubricants, parts, and accessories are available from your dealer . They will help you keep your vehicle operating at its best.
T o contact NHTSA, you may either call the Auto Safety Hotline toll free at 1-800-424-9393 (or 366-0123 in W ash- ington DC area) or write to: NHTSA, U.S. Dept. of T ransportation, W ashington DC 20590. Y ou can also obtain other information about motor vehicle safety from the Hotline.
PUBLICA TION ORDER FORMS 9.
.
DEP ARTMENT OF TRANSPORT A TION UNIFORM TIRE QUALITY GRADES The following describes the tire grading categories estab- lished by the National highway T raffic Safety Adminis- tration. The specific grade rating assigned by the tire’s manufacturer in each category is shown on the sidewall of the tires on your car .
T emperature Grades The temperature grades ar e A (highest), B, and C, repre- senting the tire’s r esistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel.
INDEX 10.
About Y our Brakes ...................... 1 3 4 ABS (Anti-Lock Brake) System ........... 91,134 Accident Damage ....................... 1 9 9 Adding Engine Coolant (Antifreeze) ......... 1 8 9 Adding Fuel .......................... 1 4 6 Air Cleaner , Engine .
Location ......................... 159,181 Saving Feature .................... 60,61,63 Belts, Engine .......................... 1 8 0 Body Mechanism Lubrication .............. 1 8 4 Brake, Parking ......................... 1 3 2 Brake System ........
W ashing ............................ 1 9 8 W axing ............................. 1 9 8 Wheels ............................. 1 9 9 W indshield W iper Blades ............... 1 8 6 Climate Control ........................ 1 1 4 Clock ...................
Door Opener , Garage ..................... 7 0 Drive Belts ............................ 1 7 8 Drive Shaft Universal Joints ............... 1 8 4 Driving On Slippery Surfaces .................. 1 6 1 W ith an Automatic T ransaxle ............ 1 2 9 Electric Remote Mirrors .
Additives ........................... 1 4 6 Filler Cap ........................... 1 4 7 Filter .............................. 1 8 0 Gauge .............................. 8 8 Light ............................... 8 8 Materials Added ...................
Instrument Cluster ..................... 87,88 Instrument Panel and Contr ols .............. 8 6 Instrument Panel Cover .................. 2 0 0 Instrument Panel Lens Cleaning ............ 2 0 1 Interior Fuses .......................... 2 0 2 Interior Lights .
Headlights ........................... 6 2 Headlights On Reminder ................ 6 2 High Beam Indicator ................... 8 9 Illuminated Entry ...................... 1 4 Instrument Cluster ..................... 6 1 Interior .....................
Electric Remote ....................... 5 4 Outside ............................. 5 4 Rearview ............................ 5 3 V anity .............................. 5 5 Mopar Parts ........................ 171,231 Multi-Function Control Lever ......
Pregnant W omen and Seat Belts ............. 3 2 Programmable Electr onic Features ......... 71,75 Programming T ransmitters ............ 20,71,75 Radial Ply T ires ........................ 1 3 8 Radiator Cap .......................... 1 8 9 Radio ...
Service Engine Soon Light ................ 1 6 9 Service Manuals ........................ 2 3 3 Setting the Clock ........................ 9 3 Shoulder Belts .......................... 3 1 Side Airbag ............................ 3 8 Side V iew Mirror Adjustment .
Radial ............................. 1 3 8 Replacement ......................... 1 4 1 Rotation ............................ 1 4 2 Snow T ires .......................... 1 4 0 Spare T ire ........................... 1 3 9 Spinning ....................
W arning Flasher , Hazard ................. 1 5 2 W arnings and Cautions .................... 6 W arranty Information ................. 148,231 W ashers, W indshield .................... 1 8 6 W ashing V ehicle ........................ 1 9 8 W axing and Polishing .
デバイスDodge 2004 Intrepidの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Dodge 2004 Intrepidをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはDodge 2004 Intrepidの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Dodge 2004 Intrepidの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Dodge 2004 Intrepidで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Dodge 2004 Intrepidを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はDodge 2004 Intrepidの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Dodge 2004 Intrepidに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちDodge 2004 Intrepidデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
