Dodgeメーカー2005 Viperの使用説明書/サービス説明書
ページ先へ移動 of 264
T ABLE OF CONTENTS SECTION P AGE 1 INTRODUCTION ............................................................. 3 2 THINGS TO KNOW BEFORE ST AR TING YOUR VEHICLE .............................. 9 3 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE ...........
.
INTRODUCTION CONTENTS 䡵 Introduction ........................... 4 䡵 How T o Use This Manual .................. 4 䡵 W arnings And Cautions ................... 6 䡵 V ehicle Identification Number ............... 6 䡵 V ehicle Modifications / Alterations .
INTRODUCTION This manual has been prepar ed with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your new vehicle. It is supplemented by a W arranty Information Booklet and various customer oriented documents.
INTRODUCTION 5 1.
W ARNINGS AND CAUTIONS This manual contains W ARNINGS against operating procedur es which could result in an accident or bodily injury . It also contains CAUTIONS against procedures which could result in damage to your vehicle. If you do not read this entir e manual you may miss important information.
VEHICLE MODIFICA TIONS / AL TERA TIONS W ARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death.
.
THINGS T O KNOW BEFORE ST ARTING YOUR VEHICLE CONTENTS 䡵 A W ord About Y our Keys .................. 1 1 ▫ Ignition Key .......................... 1 1 ▫ Key-In-Ignition Reminder ................ 1 2 ▫ Power Accessory Delay Feature ............
▫ T o Arm The V ehicle Theft Alarm System ...... 2 0 ▫ Entering The T runk W ith The System Armed . . .21 ▫ Security System Disarm .................. 2 2 ▫ T amper Alert ......................... 2 3 䡵 T runk Safety W arning ................
A WORD ABOUT YOUR KEYS The dealer that sold you your new V iper has the key code numbers for your vehicle locks. These numbers can be used to order duplicate keys fr om your dealer or a locksmith. Ask your dealer for these numbers and keep them in a safe place.
start the vehicle fully apply the parking brake, press the clutch pedal to the floor , place the gear selector in NEUTRAL, move the key to the ON position, and press the red ENGINE ST AR T button located on the instrument panel.
Power Accessory Delay Feature The Power Accessory Delay feature pr ovides the cus- tomer with the ability to operate the power windows, and the radio for 2 minutes after the ignition switch is turned off.
will flash DOOR UNLOCKED every 2 seconds. After about 40 seconds with the ignition off, the display will turn off. NOTE: If you attempt to lock the doors with the key in the ignition and the driver ’ s door open, the doors will not lock.
Automatic Door Locks The doors will lock automatically from outside the ve- hicle when vehicle speed reaches 18 miles per hour with the ignition On and the DOOR UNLOCKED displayed in the odometer will disappear . NOTE: If the vehicle is moving faster than 5 MPH, the inside and outside door handles are ignor ed.
T o Unlock the Doors: Press and r elease the UNLOCK button on the transmitter . The front and r ear park/turn signal lights will blink once to indicate that only the driver ’ s door is unlocked.
T o Lock the Doors: NOTE: T o enable/disable the Lamp Flash, see proce- dure described above. Press and r elease the LOCK button on the transmitter . The horn will chirp once and the park and tail lights will blink to acknowledge that the door is locked and that the alarm system is armed.
T o Program T ransmitters: This feature allows you to pr ogram transmitters in case one is lost or an extra transmitter(s) is desired. Up to 4 transmitters can be programmed to your vehicle. T o program another transmitter follow these steps: 1. T urn the ignition switch to the ON/RUN position and set the parking brake.
T ransmitter Battery Service The replacement battery number is 2016. This is a generic battery , readily available at local retail stor es. 1. Pry the transmitter halves apart with a coin or similar object. 2. Remove and r eplace the batteries. 3. Reassemble the transmitter case and test operation.
VEHICLE THEFT ALARM The system monitors the doors, trunk, hood, and ignition for unauthorized operation. Once the system has been armed, opening any door , trunk (with the ignition key), hood or turning the ignition key to any position will trigger an alarm.
4. The Security light will periodically flash, once every 6 seconds, to show that the system is still armed. CAUTION! If the Security lamp flashes twice every 6 seconds, then the vehicle was tampered with! Entering the T runk with the System Armed T o enter the trunk with the system armed, the Remote Keyless Entry T runk button must be pressed.
Security System Disarm There ar e two ways to disarm the system: 1. Driver door key cylinder: Insert the key in the cylinder located under the driver ’ s door mirror . This will disarm the V ehicle Theft Alarm System and open the driver ’ s door .
T amper Alert If the horn sounds 3 times when you unlock the vehicle using the Remote Keyless Entry transmitter or key , the alarm has been activated. Check the vehicle for tamper- ing. NOTE: If the Security lamp flashes twice every 6 seconds, then the vehicle was tampered with.
T runk Internal Emergency Release NOTE: As a security measure, a T runk Internal Emer - gency Release lever is built into the trunk latching mechanism.
NOTE: W indows cannot be driven up during accessory delay with a door open. NOTE: If the windows are completely closed, each respective window will dr op slightly when either door is opened. The windows return to their full up position when the door is again closed.
Auto Down Feature Both windows have an auto down feature. Pr ess the window switch to the second detent, release, and the window will go down automatically .
Please pay close attention to the information in this section. It tells you how to use your restraint system properly to keep you and your passenger as safe as possible.
W ARNING! W earing a seat belt incorrectly is dangerous. Seat belts are designed to go around the large bones of your body . These are the strongest parts of your body and can take the forces of a collision the best. W earing your belt in the wrong place could make your injuries in a collision much worse.
3. Slide the latch plate up the webbing as far as necessary to make the belt go around your lap. 4. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “ click. ” W ARNING! A belt that is too loose will not protect you as well.
5. Position the lap belt acr oss your thighs, below your abdomen. T o remove slack in the lap belt portion, pull up a little on the shoulder belt, as shown. 6. T o loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt. A snug belt reduces the risk of sliding under the belt in a collision.
W ARNING! A twisted belt can ’ t do its job as well. In a collision it could even cut into you. Be sure the belt is straight. If you can ’ t straighten a belt in your vehicle, take it to your dealer and have it fixed. 8. T o release the belt, push the r ed button marked PRESS on the buckle.
2. Start the engine and wait for the Seat Belt W arning Light to turn off. 3. W ithin 60 seconds of starting the vehicle, unbuckle and then re-buckle the driver ’ s seat belt at least thr ee times within 10 seconds, ending with the seat belt buckled.
NOTE: The anti-submarining belt and the shoulder belt are attached to eye bolts at designated locations and should be removed fr om the vehicle when not in use.
Child Restraint Everyone in your vehicle needs to be buckled up all the time, babies and children, too. W ARNING! In a collision, an unrestrained child, even a tiny baby , can become a missile inside the vehicle.
W ARNING! A rearward facing infant restraint must not be used in your V iper unless the passenger airbag has been shut off. A rearward facing infant restraint may be struck by a deploying passenger airbag which may cause severe or fatal injury to the infant.
Buckle the child into the seat exactly as the child seat manufacturer ’ s dir ections tell you. The latch plate on the lap/shoulder belt will keep the belt tight. When your infant carrier or child seat is not in use, secure it with the seat belt or remove it fr om the vehicle.
system provides for the installation of the child r estraint without using the vehicle seat belt. The passenger seat has an exclusive lower anchorage. These are r ound bars, located at the lower area of the seat back, one on each side of the passenger seat.
T o attach the tether strap to the anchor , move the seatback fully forward. Pass the child r estraint tether hook through either opening in the seatback under the head restraint. Attach the tether hook to the anchor loop, recline the seatback full r earward and move the seat to its most rearwar d position.
W ARNING! An incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchor position directly behind the child seat to secure a child restraint top tether strap.
T o convert the emergency locking mode to automatic locking mode for seat belts equipped with automatic locking retractors, grasp on the shoulder belt portion of the belt and pull all of the webbing out of the retractor .
Supplemental Restraint System (SRS) - Airbag This vehicle has airbags for the driver and passenger as a supplement to the seat belt restraint systems. The driver ’ s airbag is mounted in the steering wheel. The passenger side airbag is mounted in the instrument panel, under a cover marked SRS/AIRBAG.
in collisions where the airbags deploy , you need the seat belts to keep you in the right position for the airbags to protect you pr operly . Here ar e four simple steps you can take to minimize the risk of harm from a deploying airbag.
2. All occupants should wear their lap and shoulder belts properly . 3. The driver and passenger seats should be moved back as far as practical to allow the airbags room to inflate.
How The Airbag System W orks • A crash sensor in the occupant compartment deter- mines if a frontal impact is sever e enough to requir e the airbag. The sensor will not detect side, roll over , or rear impacts. The crash sensor is connected to the diagnostic unit and to the airbag/inflator unit.
W ARNING! Do not put anything on or around the airbag covers or attempt to manually open them. Y ou may damage the airbags and you could be injured because the airbags are not there to protect you. These protective covers for the airbag cushions are designed to open only when the airbags are inflating.
front passenger as the airbags deploy and unfold. The abrasions are similar to friction r ope burns or those you might get sliding along a carpet or gymnasium floor . They are not caused by contact with chemicals. They are not permanent and normally heal quickly .
because the infant has a medical condition which makes it necessary for the driver to be able to see the infant, • is a child, age 1 to 12 who must ride in the front seat because there is no r ear s.
NOTE: When the passenger airbag is turned off the airbag off light will illuminate T o Shut Off the Passenger Airbag: • Place only the tip of the ignition key in the on/off switch, turn the key clockwise, and remove the key from the switch. This will shut of f the passenger side airbag.
Maintaining Y our Airbag System W ARNING! • Modifications to any part of the airbag system could cause it to fail when you need it. Y ou could be injured because the airbag is not there to protect you. Do not modify the components or wiring, including adding any kind of badges or stickers to the airbag covers.
T ransporting Pets Deploying airbags could harm your pet. An unrestrained pet will be thrown about and possibly injur ed, or injure a passenger during panic braking or in a collision. Pets should be restrained in pet harnesses or pet carriers that are secur ed by seat belts.
SAFETY TIPS Exhaust Gas W ARNING! Exhaust gases can injure or kill. They contain carbon monoxide (CO) which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. T o avoid breathing (CO) follow the safety tips below .
Safety Checks Y ou Should Make Outside the V ehicle T ires Examine tires for excessive tr ead wear or uneven wear patterns. Check for stones, nails, glass, or other objects lodged in the tread. Inspect for tr ead cuts or side wall cracks. Check wheel nuts for tightness and tires for proper pr essure.
UNDERST ANDING THE FEA TURES OF YOUR VEHICLE CONTENTS 䡵 Convertible T op Operation ................. 5 5 ▫ T o Lower The T op ...................... 5 6 ▫ T o Raise The T op ...................... 5 6 ▫ Convertible T op Boot Cover Installation – If Equipped .
▫ Multi-Function Control Lever .............. 7 4 ▫ Headlights, Parking Lights, Instrument Panel Lights, And Front Fog Lights .............. 7 5 ▫ Daytime Running Lights ................. 7 6 ▫ Lights-On Reminder .................... 7 6 ▫ Headlight T ime Delay .
CONVERTIBLE TOP OPERA TION W ARNING! The convertible top does not provide the structural protection that a reinforced metal roof does, and the fabric top cannot be expected to prevent the ejection of the occupants of a vehicle in a collision.
T o Lower the T op: 1. T o lower the top, first ensure that the door windows are lower ed at least an inch. 2. Depr ess the button at the top of the latch upwards and then pull the handle down and rearwar d, towards you.
3. Release the lever located behind the driver ’ s seat and nestled in the folded convertible top (as pictured). T o aid in disengaging the latch, press down on the convertible top while pressing on the latch lever . 4. Manually raise the top until it meets the windshield header (as pictured).
6. While sitting inside the vehicle, hold onto the handles and pull the top towards the windshield header . Push the latch handle forward and engage the latch hook to the windshield receiver r od. 7. Ensur e the outboard locating pins are in their r espec- tive receiving holes in the windshield header .
engage the latch hook and close the latch. Several weeks of normal convertible top usage will reduce these ef forts. Convertible T op Boot Cover Installation–If Equipped 1. Open the trunk. 2. Lower the convertible top and make sur e that the convertible top latch handle is placed in the stowed position.
4. Slide pocket over the fr ont corner of convertible top on the passenger side. 5. Str etch and slide pocket over the front corner of convertible top on the driver side.
6. T uck cover under leading edge of convertible top. 7. Clip tab under trunk lid stop and quarter panel flange on outer edge on the passenger side. T ucking Boot Cover Attaching Passenger Side T ab U.
8. Push down to engage inboar d tab on the passenger side. 9. Clip tab under trunk lid stop and quarter panel flange on outer edge on the driver side. Engaging Passenger Side T ab Attaching Driver Sid.
10. Push down to engage inboar d tab on the driver side. Push down on convertible top behind driver seat to lock down. 1 1. Stretch out and smooth cover fr om rear of vehicle.
12. Ensur e that the forward edge of the convertible top boot is tucked in fully after the trunk is closed. Convertible T op Boot Cover Removal and Storage 1.
3. Pull up to disengage the inboar d tab on the passenger side. 4. Fold each of the outer edges of the convertible top cover inward. Disengaging Passenger Side T ab Folding Outer Edges UNDERST ANDING .
5. Fold the convertible top cover again. Place the cover into the bag. Store the cover in the tr unk or a dry secure area. CONSOLE FEA TURES The front console has a r emovable ashtray , power outlet/ cigarette lighter and power window switches.
MIRRORS Inside Day/Night Mirror Adjust the mirror to center on the view thr ough the rear window . A pivot system allows for horizontal and verti- cal mirror adjustment. Annoying headlight glare can be r educed by moving the small control under the mirr or to the night position (toward r ear of vehicle).
Electric Remote Control Mirrors Both of the outside mirrors can be adjusted by using the remote contr ols mounted inside the driver ’ s door , below the door handle and power door switch. NOTE: Place the mirror selector switch in the center (neutral) position to prevent accidental movement of the mirrors.
W ARNING! V ehicles and other objects seen in the right side convex mirror will look smaller and farther away than they really are. Relying too much on your right side mirror could cause you to collide with another vehicle or other object. Use your inside mirror when judging the size or distance of a vehicle seen in this convex mirror .
W ARNING! Adjusting a seat while the vehicle is moving is dangerous. If you are driving, the sudden movement of the seat could cause you to lose control. Y ou could be injured. Adjust any seat only while the vehicle is parked. Do not ride with the seatback reclined so that the shoulder belt is no longer riding against your chest.
Reclining Seat The recliner contr ol is on the side of the seat on the door-side. T o recline, lean forward slightly befor e pulling the lever , then lean back to the desired position, and release the lever . Lean forward and pull the lever to return the seatback to its original position.
Then push the safety catch handle located under the front edge of the hood toward the right. Raise the fr ont of the hood. NOTE: Assist props will raise the hood to a normal customer usage position. If greater access is r equired, the hood may be pushed up at the front, raising the hood beyond the initial opening height.
W ARNING! If the hood is not fully latched, it could open when the vehicle is moving and block your forward vision. Be sure the hood latches are fully latched before driving. LIGHTS Courtesy/Reading Lights These lights, located under the rearview mirr or , come on whenever a door is opened or the illuminated entry system is activated.
Interior Lights The interior lights come on when a door is opened and the dome switch is not in the defeat position. Battery Saver Feature — Interior Lights The interior courtesy lights come on when a door is open or left ajar . T o prevent battery drain, if you leave a door open or ajar , these lights will turn off after 15 minutes.
Interior Light Defeat (OFF) Rotate the dimmer control to the ex- treme bottom “ OFF ” position. The in- terior lights will remain of f when the doors are open. Parade Mode (Daytime Brightness Feature) Rotate the dimmer control to the first detent (white semi-circle).
T o change the brightness of the instrument panel lights, rotate the center portion of the Multi-Function Contr ol Lever up or down. Daytime Running Lights The fog lights will come on as Daytime Running Lights whenever the ignition switch is on, the headlights are of f, and the parking brake is off.
If the ignition switch is turned to any position other than the Off position at any time during the 3 minute delay period the battery saver feature will be disabled.
If either light remains on and does not flash, or ther e is a very fast flash rate, check for a defective outside light bulb. If an indicator fails to light when the lever is moved, it would suggest that the fuse or indicator bulb is defective.
W ARNING! T ilting the steering column while the vehicle is moving is dangerous. W ithout a stable steering col- umn, you could lose control of the vehicle and have an accident. Adjust the column only while the ve- hicle is stopped. Be sure it is locked before driving.
T o adjust the pedals: • Adjust the seat to a comfortable driving position. • Adjust the pedals to a position that allows full pedal travel. • It may be necessary to make further small adjustments to find the best possible seat/pedal position. W ARNING! Do not adjust the pedals while the vehicle is moving.
T o adjust the left foot rest: • Loosen the nut on the pedal using a 13 mm socket. • Slide the pedal fore, aft and/or r otate up or down to find a comfortable position. • Retighten the nut, being careful not to overtighten. WINDSHIELD WIPERS AND W ASHERS The wipers and washers are operated by a switch in the right control lever .
Windshield W ashers T o use the washer , pull the control lever towar d you and hold while spray is desired. If the lever is pulled while in the delay range, the wiper will operate in low speed for two wipe cycles after the lever is released, and then resume the intermittent interval pr eviously selected.
UNDERST ANDING YOUR INSTRUMENT P ANEL CONTENTS 䡵 Instrument Panel Featur es .................. 8 5 䡵 Instrument Cluster Description .............. 8 6 ▫ Speedometer .......................... 8 6 ▫ T urn Signal Indicators ................... 8 7 ▫ Hazard Indicator .
▫ CD Player Operation .................... 9 8 䡵 CD/DVD Disc Maintenance ............... 1 0 3 䡵 Radio Antenna ........................ 1 0 3 䡵 Radio Operation And Cellular Phones ........ 1 0 3 䡵 V entilation ............................ 1 0 4 䡵 Climate Controls .
INSTRUMENT P ANEL FEA TURES UNDERST ANDING YOUR INSTRUMENT P ANEL 85 4.
INSTRUMENT CLUSTER DESCRIPTION Speedometer Shows the vehicle speed in miles-per- hour and kilometers-per-hour . Odometer/T rip Odometer The odometer shows the total distance the vehicle has been driven.
T urn Signal Indicators The arrows will flash in unison with the corr esponding exterior turn signal when using the signal lever . Hazard Indicator Both turn signal arrows will flash in unison with all fr ont and rear turn signals when the hazar d warning switch is used.
W ARNING! If both ABS and/or Brake W arning lamps become illuminated, please seek service immediately! Y our V iper will have diminished braking capability and control if ABS and/or service brake systems are not working properly . Have your brake system serviced immediately .
CAUTION! Prolonged driving with the light on could cause further damage to the emission control system. It could also affect fuel economy and driveability . The vehicle must be serviced before any state emissions tests can be performed. If the light is flashing, severe catalytic converter damage and power loss will soon occur .
T runk Ajar Light This light indicates that the trunk is not latched. Engine Coolant T emperature Light A r ed LED light on the Coolant T emperature gauge will illuminate to warn of an overheated engine coolant condition. Low Oil Pressure Light A red LED light on the Oil Pr essure gauge will illuminate to indicate low engine oil pressur e.
Brake System W arning Light The dual brake system provides a r eserve braking capability in the event of a failure to a portion of the hydraulic system. The warning light should be checked frequently to assur e that it is operating properly . This can be done by turning the ignition switch to a point midway between ON and ST AR T .
Gauges T achometer This gauge shows engine speed in revolutions- per-minute (RPM) times 1,000. A void excessive engine speeds in any part of the red warning zone, particularly when driving downhill or in lower gears. Coolant T emperature Gauge This gauge shows the engine coolant tempera- ture.
This gauge does not indicate the amount of oil in the engine. The engine oil level must be checked under the hood. Check the level often during severe usage. Fuel Gauge This gauge shows the amount of fuel in the gas tank. The reaction time of the gauge has been slowed to avoid needle fluctuation during pe- riods of high G force cornering.
2. Pr ess the “ H ” button to set hours or the “ M ” button to set minutes. The time setting will increase each time you press a button. RADIO GENERAL INFORMA TION Radio Broadcast Signals Y our new radio will provide excellent r eception under most operating conditions.
FM Reception Because FM transmission is based on frequency varia- tions, interference that consists of amplitude variations can be filtered out, leaving the r eception relatively clear , which is the major feature of FM radio.
Radio Operation Power/V olume Control Press the PWR/VOL control to turn the radio on. T urn the volume control clockwise to incr ease the volume. NOTE: Power to operate the radio is controlled by the ignition switch. It must be in the ON or ACC position to operate the radio.
T o Set The Radio Push-Button Memory When you are r eceiving a station that you wish to commit to push-button memory , press the SET RND button. SET 1 will show in the display window . Select the “ 1 – 6 ” button you wish to lock onto this station and press and release that button.
T ime Button Press the TIME button to change the display between radio frequency and time. General Information This radio complies with Part 15 of FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following conditions: 1. This device may not cause harmful interfer ence, 2.
If you insert a disc with the ignition ON and the radio ON, the unit will switch from radio to CD mode and begin to play when you insert the disc. The display will show the disc number , the track number , and index time in minutes and seconds. Play will begin at the start of track 1.
Scan Press the Scan button to scan thr ough each track on the CD currently playing. FF/TUNE/R W Press FF (Fast Forwar d) and the CD player will begin to fast forward until FF is r eleased. The R W ( Reverse) button works in a similar manner . Random Play — SET / RND Press the RND button while the CD is playing to activate Random Play .
Program T ype Radio Display Information Inform Jazz Jazz Foreign Language Language News News Nostalgia Nostalga Oldies Oldies Personality Persnlty Public Public Rhythm and Blues R & B Religious Mu.
By pressing the SCAN button when the PTY icon is displayed, the radio will stop at every PTY station on the band and list each corresponding pr ogram type in the radio display . T ime Press the TIME button to change the display fr om elapsed CD playing time to time of day .
CD/DVD DISC MAINTENANCE T o keep the CD/DVD discs in good condition, take the following precautions: 1. Handle the disc by its edge; avoid touching the surface. 2. If the disc is stained, clean the surface with a soft cloth, wiping from center to edge.
VENTILA TION When the ventilation mode is selected, outside air comes through the panel outlets. Air will enter the vehicle with or without the blower in operation. CLIMA TE CONTROLS The Air Conditioning System allows you to balance the temperature, amount and dir ection of the air circulating throughout the vehicle.
The controls ar e as follows: Fan Control Use this control to r egulate the amount of air forced thr ough the sys- tem in any mode you select. T urn the control clockwise to incr ease fan speed. T urn the control to the O — Of f position to shut off the fan and to prevent any outside air fr om entering the vehicle.
Panel Air is directed thr ough the outlets in the instrument panel. These outlets can be adjusted to direct air flow . Bi-Level Air is directed thr ough the instrument panel and floor outlets. A small amount of air is also directed through the defr ost outlets.
shows that the Air Conditioning compressor is on. Con- ditioned air is now directed thr ough the outlets selected. Pushing the button a second time turns the compressor OFF . Slight changes in engine speed or power may be noticed when the compressor is on.
The blower air will heat faster in cold weather if you use only the low blower speeds for the first ten minutes of vehicle operation. During engine warm-up in cold weather , use the Defrost mode to direct any cold air away fr om the occupants.
ST ARTING AND OPERA TING CONTENTS 䡵 Starting Procedur es ..................... 1 1 1 ▫ If Engine Fails T o Start ................. 1 1 2 ▫ After Starting ........................ 1 1 4 䡵 T ransmission Shifting .................... 1 1 4 ▫ Recommended Shift Speeds .
▫ Compact Spare T ire — If Equipped ......... 1 3 4 ▫ Limited Use Spare — If Equipped ......... 1 3 5 ▫ T ire Spinning ........................ 1 3 6 ▫ T read W ear Indicators .................. 1 3 7 ▫ Replacement T ires ...............
ST ARTING PROCEDURES CAUTION! Long periods of engine idling, especially at high engine speeds, can cause excessive exhaust tempera- tures which can damage your vehicle.
instrument panel and r elease when the engine starts. If the engine has not started within 3 seconds, slightly depress the accelerator pedal while continuing to crank. If the engine fails to start within 10 seconds, turn the key to the “ OFF ” position, wait 5 seconds, then repeat the normal starting procedur e.
W ARNING! Do not attempt to push or tow your vehicle to get it started. Unburned fuel could enter the catalytic converter and once the engine has started, ignite and damage the converter and vehicle. If the vehicle has a discharged battery , booster cables may be used to obtain a start from a booster battery or the battery in another vehicle.
After Starting The idle speed will automatically decrease as the engine warms up. W ARNING! Never pour fuel or other flammable liquid into the throttle body air inlet opening in an attempt to start the vehicle. This could result in flash fire causing serious personal injury .
Recommended Shift Speeds T o use your manual transmission for fuel economy it should be upshifted as listed below . Shift at the vehicle speeds listed for acceleration. Earlier upshifts during cruise conditions (r elatively steady speeds) will result in increased fuel economy , and may be used as indicated.
T o maintain a safe speed and prolong brake life, down- shift to maintain a safe speed when descending a steep grade. W ARNING! Skipping more than one gear while downshifting, could cause you to lose control of your vehicle. Y ou could have an accident.
Before leaving the vehicle, make sur e you fully apply the parking brake. Place the transmission in REVERSE. Fail- ure to do so may cause the vehicle to r oll and cause damage or injury . As an added precaution, turn the fr ont wheels toward the curb on a downhill grade and away from the curb on an uphill grade.
All vehicle wheels and tires must be the same size and type as the original equipment wheels and tires must be properly inflated to pr oduce accurate signals for the computer . W ARNING! Significant over or under inflation of tires, or mixing sizes of front or rear tires or wheels on the vehicle can lead to loss of braking effectiveness.
CAUTION! The Anti-Lock Brake System is subject to possible detrimental effects of electronic interference caused by improperly installed after-market radios or tele- phones.
NOTE: During severe braking conditions, a pulsing sensation may occur and a clicking noise will be heard. This is normal, indicating that the Anti-Lock Brake System is functioning. W ARNING! T o use your brakes and accelerator more safely , follow these tips: • Do not “ ride ” the brakes by resting your foot on the pedal.
In the event power assist is lost for any reason (for example, repeated brake applications with the engine off), the brakes will still function. The ef fort requir ed to brake the vehicle will be much greater than that r equired with the power system operating.
TIRE SAFETY INFORMA TION Tire Markings NOTE: • P(Passenger)-Metric tire sizing is based on U.S. design standards. P-Metric tir es have the letter “ P ” molded into the sidewall preceding the size designation. Ex- ample: P215/65R15 95H. • European Metric tir e sizing is based on European design standards.
T ire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standar ds ⴖ ....blank.... ⴖ = Passenger car tire based on Eur opean design standards LT = Light T ruck tire based on U.
EXAMPLE: Service Description: 95 = Load Index — A numerical code associated with the maximum load a tire can carry . H = Speed Symbol — A symbol indicating the range of speeds at which a tire can carry a load corr esponding to its load index under certain operating conditions.
Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire however the date code may only be on one side. T ires with white sidewalls will have the full TIN including date code located on the white sidewall side of the tire.
Tire Loading and T ire Pressure T ire Placard Location NOTE: The proper cold tir e inflation pressur e for pas- senger cars is listed on either the face of the driver ’ s door or the driver ’ s side “ B ” pillar .
T ire and Loading Information Placard This placard tells you important information about the, 1) number of people that can be carried in the vehicle 2) the total weight your vehicle can carry 3) the tire size designed for your vehicle 4) the cold tire inflation pr essures for the fr ont, rear and spare tir es.
lbs. ” on the T ire and Loading Information placard. The combined weight of occupants, cargo/luggage and trailer tongue weight (if applicable) should never exceed the weight refer enced here.
ST ARTING AND OPERA TING 129 5.
W ARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle.
2. Economy — Improper inflation pr essures can cause uneven wear patterns to develop across the tir e tread. These abnormal wear patterns will reduce tr ead life resulting in a need for earlier tire r eplacement. Underinflation also increases tir e rolling r esistance and results in higher fuel consumption.
check tire pr essure. Do not make a visual judgement when determining proper inflation. Radial tir es may look properly inflated even when they ar e underinflated. CAUTION! After inspecting or adjusting the tire pressure al- ways reinstall the valve stem cap – if equipped.
T ire Pressures for High Speed Operation The manufacturer advocates driving at safe speeds within posted speed limits. Where speed limits or condi- tions are such that the vehicle can be driven at high speeds, maintaining correct tir e inflation pressur e is very important.
Radial-Ply Tires W ARNING! Combining radial ply tires with other types of tires on your vehicle will cause your vehicle to handle poorly . The instability could cause an accident. Al- ways use radial ply tires in sets of four (or 6, in case of trucks with dual rear wheels).
Do not install a wheel cover or attempt to mount a conventional tire on the compact spar e wheel, since the wheel is designed specifically for the compact spare.
W ARNING! The limited use spare tires are for emergency use only . Installation of this limited use spare tire affects vehicle handling. W ith this tire, do not drive more than 60 mph (100 km/h). Keep inflated to the cold tire inflation pressure listed on either your tire placard or limited use spare tire and wheel assembly .
T read Wear Indicators T read wear indicators ar e in the original equipment tires to help you in determining when your tires should be replaced. These indicators are molded into the bottom of the tr ead grooves and will appear as bands when the tr ead depth becomes 1/16 inch (2 mm).
W ARNING! • Do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change sus- pension dimensions and performance characteris- tics, resulting in changes to steering, handling, and braking of your vehicle.
Improper alignment will not cause vehicle vibration. V ibration may be a result of tire and wheel out-of- balance. Proper balancing will r educe vibration and avoid tire cupping and spotty wear .
CAUTION! The Low T ire Pressure (L TP) system has been opti- mized for the original equipment tires and wheels. The L TP system pressures have been established for the tire size equipped on your vehicle. Undesirable operation or sensor damage may result when using replacement equipment that is not of the same size, type, and/or style.
Tire Storage T ire storage is addressed in the Michelin Limited T ire W arranty Booklet. Specific recommendations on guidelines for long term tire storage for this vehicle should be r equested of the Michelin T ire Corporation 1-800-433-6838.
FUEL REQUIREMENTS Y our vehicle is designed to meet all emis- sion regulations and pr ovide excellent fuel economy when using high quality pre- mium unleaded gasoline having an octane rating of 91 or higher . Spark Knock Light spark knock at low engine speeds is not harmful to your engine.
Gasoline/Oxygenate Blends Some fuel suppliers blend unleaded gasoline with mate- rials called oxygenates such as 10% alcohol, MTBE, ETBE or T AME. Oxygenates are r equired in some areas of the country during the winter months to reduce carbon monoxide emissions.
Materials Added to Fuel All gasoline sold in the United States and Canada is requir ed to contain effective detergent additives. The use of additional detergents or other additives is not needed under normal conditions.
Carbon Monoxide W arnings W ARNING! Carbon monoxide (CO) in exhaust gases is deadly . Follow the precautions below to prevent carbon monoxide poisoning: • Do not inhale exhaust gases. They contain carbon monoxide, a colorless and odorless gas which can kill.
W ARNING! Remove the fuel tank filler tube cap (gas cap) slowly to prevent fuel spray from the filler neck that may cause injury . The volatility of some gasolines may cause a buildup of pressure in the fuel tank that may increase while you drive the vehicle.
WHA T T O DO IN EMERGENCIES CONTENTS 䡵 Hazard W arning Flasher .................. 1 4 8 䡵 If Y our Engine Overheats ................. 1 4 8 䡵 Jump-Starting Procedur es ................. 1 5 0 䡵 Driving On Slippery Surfaces .............. 1 5 4 ▫ T raction .
HAZARD W ARNING FLASHER The flasher switch is on the top of the steering column, just behind the steering wheel. Depress the flasher button and all front and r ear directional signals will flash. Depress the flasher button again to turn the flashers off.
• In city traffic — While moving, shift into the highest gear possible to reduce engine RPM. NOTE: There ar e steps that you can take to slow down an impending overheat condition. If your air conditioner is on, turn it off. The air conditioning system adds heat to the cooling system and turning off the A/C removes this heat.
JUMP-ST ARTING PROCEDURES W ARNING! • Do not attempt to push or tow your vehicle to get it started. Unburned fuel could enter the catalytic converter and once the engine has started, ignite and damage the converter and vehicle.
The battery is located under the battery access panel inside the trunk on the left side. Remote battery terminals are located in the engine compartment for jump starting. NOTE: Remove the floor portion of the trunk carpet to gain access to the battery .
without letting the vehicles touch. Set the parking brake, place the transmission in neutral and turn the ignition OFF for both vehicles. 3. T urn off the heater , radio and all unnecessary electrical loads. 4. If you ar e jump starting your V iper , connect one end of a jumper cable to the positive terminal of the booster battery .
Thermostat Housing shown in illustration) of your V iper and the other end to the engine of the other vehicle. Make sure that you have a good contact on the engines. NOTE: When using another vehicle as the power source, turn of f all accessories. 8. T urn off the Theft Security System.
DRIVING ON SLIPPER Y SURF ACES W ARNING! Rapid acceleration on slippery surfaces is danger- ous. Y ou could lose control of the vehicle and possi- bly have an accident. Accelerate slowly and carefully whenever there is likely to be poor traction (ice, snow , wet, mud, loose sand, etc.
FREEING A STUCK VEHICLE If your vehicle becomes stuck in mud, sand or snow , it can often be moved by a rocking motion. T urn your steering wheel right and left to clear the area ar ound the front wheels. Then shift back and forth between Reverse and First gear .
.
MAINT AINING YOUR VEHICLE CONTENTS 䡵 8.3L Engine Compartment ................ 1 6 0 䡵 Onboard Diagnostic System (OBD II) ......... 1 6 1 䡵 Emissions Inspection And Maintenance Programs ............................ 1 6 2 䡵 Replacement Parts ...
▫ Body Lubrication ..................... 1 7 9 ▫ Front And Rear Suspension Ball Joints ...... 1 7 9 ▫ Steering Linkage ...................... 1 8 0 ▫ Body Mechanism Lubrication ............. 1 8 0 ▫ W indshield W ashers ................... 1 8 2 ▫ Exhaust System .
▫ High Intensity Discharge Headlights (HID) . . . 207 ▫ T ail, T ail/Stop, And Marker Lamp Bulb Replacement ......................... 2 0 7 ▫ Backup And Rear T urn Signal Lamp Bulb Replacement ......................... 2 0 8 ▫ License Plate Light .
8.3L ENGINE COMP ARTMENT 8.3L Engine Compartment 160 MAINT AINING YOUR VEHICLE.
ONBOARD DIAGNOSTIC SYSTEM (OBD II) T o meet new government regulations and pr omote cleaner air , your vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions and engine control systems.
EMISSIONS INSPECTION AND MAINTENANCE PROGRAMS In some localities, it may be a legal requir ement to pass an inspection of your vehicle ’ s emissions control system.
ignition key or start the engine. This means that your vehicle ’ s OBD system is not ready and you should not proceed to the I/M station. b. The MIL will not flash at all and will remain fully illuminated until you turn off the ignition key or start the engine.
NOTE: Intentional tampering with emissions control systems can result in civil penalties being assessed against you. W ARNING! Y ou can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the proper equipment.
The best time to check the oil level is approximately 5 minutes after a fully warmed up engine is turned off or before starting the engine after it has sat overnight. Checking the oil while the vehicle is on level ground also will improve the accuracy of the oil level r eadings.
• T railer towing • Off-r oad or desert driving • If equipped for and operating with E – 85 (ethanol) fuel If none of these apply to you, then change your engine oil every 6,000 miles (10 000 km) or 6 months, whichever comes first and follow the maintenance recommenda- tions in Schedule A .
Materials Added to Engine Oil The manufacture str ongly recommends against the addi- tion of any additives (other than leak detection dyes) to the engine oil. Engine oil is an engineered pr oduct and it ’ s performance may be impaired by supplemental ad- ditives.
Drive Belts — Check Condition and T ension At the mileage shown in the appropriate “ Maintenance Schedule ” , check the condition of the drive belt for condition and proper tension.
CAUTION! Damage to the catalytic converter can result if your vehicle is not kept in proper operating condition. In the event of engine malfunction, particularly involv- ing engine misfire or other apparent loss of perfor- mance, have your vehicle serviced promptly .
T o minimize the possibility of catalytic converter dam- age: • Do not shut off the engine or interr upt the ignition when the transmission is in gear and the vehicle is in motion. • Do not try to start the engine by pushing or towing the vehicle.
Crankcase Emission Control System Proper operation of this system depends on fr eedom from plugging due to deposits. As vehicle mileage builds up, the Crankcase V entilation V alve orifice may accumu- late deposits. If a valve is not working properly , replace it with a new orifice.
NOTE: Remove the floor portion of the trunk carpet to gain access to the battery . T o service the battery: 1. Locate the battery compartment inside the trunk. 2. Remove the battery cover mounting screws and re- move the battery cover . 3. Remove the negative battery cable post and then remove the positive battery cable post connection.
W ARNING! Battery fluid is a corrosive acid solution and can burn or even blind you. Don ’ t allow battery fluid to contact your eyes, skin or clothing. Don ’ t lean over a battery when attaching clamps. If acid splashes in eyes or on skin, flush the area immediately with large amounts of water .
CAUTION! It is essential when replacing the cables on the battery that you attach the positive cable to the positive post and the negative cable to the negative post. Battery posts are marked positive (+) and negative (-) and identified on the battery case.
Start the battery save feature by doing the following: 1. Insert the key into the ignition. 2. Cycle the ignition from OFF to ACC four times with- out going into ON. Leave the switch in the OFF position after the fourth cycle. 3. Depress the driver ’ s side Power Door Lock switch in the UP dir ection.
NOTE: The exterior and interior lighting functions will not work when the vehicle is in Battery Save Mode. Exit Battery Save Mode by doing the following: 1. Press the driver ’ s door exterior handle to wake up the vehicle. 2. If the door does not open (vehicle is armed) press the remote keyless entry unlock button to unlock the vehicle.
W ARNING! • Use only refrigerants and compressor lubricants approved by the manufacturer for your air condi- tioning system. Some unapproved refrigerants are flammable and can explode, injuring you. Other unapproved refrigerants or lubricants can cause the system to fail, requiring costly repairs.
Power Steering (Pump and Reservoir) W ARNING! Fluid level should be checked with the engine off to prevent injury from moving parts. Do not overfill. Use only the manufacturer ’ s recommended fluid. Refer to Recommended Fluids, Lubricants and Genuine Parts for correct fluid type.
All power steering pumps have a dipstick. Fluid level should be maintained at the proper level indicated on the dipstick. If necessary , add fluid to restore to the pr oper indicated level. W ith a clean cloth, wipe any spilled fluid from all surfaces.
Relubrication Ball joints are lubricated at the factory with a special grease. They should be r egreased at intervals as specified in the maintenance schedules. When lubricating ball joints, use only special long life chassis grease, such as Multi-Mileage Lubricant, intended for this purpose.
Other Body Mechanisms The following body mechanisms should be inspected and, if necessary , all pivot and sliding contact areas of these components should be lubricated with the lubricant specified as.
• Rubber bushings • Starter bearing • Throttle contr ol cable • W ater pump bearings Windshield W ashers The fluid reservoir in the right side engine compartment should be checked for fluid level at regular intervals. Fill the reservoir with windshield antifr eeze (not radiator antifreeze).
Cooling System Inspection W ARNING! Y ou or others can be badly burned by hot coolant or steam from your radiator . If you see or hear steam coming from under the hood, don ’ t open the hood until the radiator has had time to cool. Never try to open a cooling system pressure cap when the radia- tor is hot.
Cooling System — Drain, Flush and Refill The cooling system should be drained, flushed and refilled at the intervals shown on the Maintenance Sched- ules. If the solution is dirty and contains a considerable amount of sediment, clean and flush with a reliable cooling system cleaner .
Adding Coolant When adding coolant, or refilling the system, a minimum solution of 50% recommended HOA T ethylene glycol engine coolant (antifreeze) and distilled water should be used. Use higher concentrations (not to exceed 70%) if temperatures below ⫺ 34 ° F( ⫺ 37 ° C) are anticipated.
W ARNING! • The warning words “ DO NOT OPEN HOT ” on the pressure cap are a safety precaution. Never add coolant to the radiator when the engine is overheated. Do not loosen or remove the pressure cap to cool overheated engine. Heat causes pres- sure to build up in the cooling system.
Coolant Level The coolant recovery bottle pr ovides a visual method for checking the coolant level without removing the pr essure cap. W ith the engine warmed up, the coolant level should be between MIN and MAX on the coolant recovery bottle.
• Make sure that the radiator and bottle overflow hoses are not kinked or obstr ucted. • Keep the front of the radiator clean. If your vehicle has air conditioning, keep the front of the condenser clean also. • Do not change the thermostat for summer or winter operation.
W ARNING! Riding the brakes can lead to brake failure and possibly an accident. Driving with your foot resting or riding on the brake pedal can result in abnormally high brake temperatures, excessive lining wear , and possible brake damage. Y ou wouldn ’ t have your full braking capacity in an emergency .
servicing. It is mandatory to replace all clamps that have been loosened or removed during service. NOTE: Inspection of brake hoses should be done when- ever the brake system is serviced and at every engine oil change.
CAUTION! Brake fluid can damage the finish of your V iper . Do not allow brake fluid to contact any painted surface. W ARNING! Overfilling the brake fluid reservoir can result in spilling brake fluid on hot engine parts and the brake fluid catching fire.
fluid level up to the requir ements described on the brake fluid reservoir . W ith disc brakes, fluid level can be expected to fall as the brake pads wear . However , low fluid level may be caused by a leak and a checkup may be needed. Use only the manufacturer ’ s r ecommended brake fluid.
T ransmission Lubricant Selection Refer to the Recommended Fluids, Lubricants and Genu- ine Parts section for correct fluid type. CAUTION! Using a transmission fluid other than the manufac- turer ’ s recommended fluid may cause deterioration in transmission shift quality .
level should be between the bottom of the filler plug and a point approximately 3/8 inch (9.5mm) below the filler plug. Lubricant Selection Use only the manufacturer ’ s r ecommended transmission fluid. Refer to the Recommended Fluids, Lubricants and Genuine Parts section for correct fluid type.
Paint and T rim Y our vehicle is exposed to the corrosive ef fects of chemi- cal fall out, salt spray , and road film. T o protect not only the paint and trim, but also exposed mountings and fixtures, it is important you wash it often and thor oughly .
Minor damage can be repair ed by using touch-up mate- rials available at your dealers. More extensive damage should be corrected in your dealer ’ s paint facility . Seat Belt Maintenance Do not bleach, dye or clean the belts with chemical solvents or abrasive cleaners.
The frame of your V iper is galvanized for rust-through protection. It is also dipped in a black E-Coat to pr otect the welded areas. A void any scratches through to bar e metal. Commercial Car W ashes W e do not recommend that you take your V iper through a commercial car wash.
Power Distribution Center 198 MAINT AINING YOUR VEHICLE.
Power Distribution Center Cavity Fuse Cir cuits 1 Cartridge Fuse 40 Amp Batt-Relay Contact, High Blower Motor Module-ABS Pump Feed 2 Cartridge Fuse 40 Amp ABS Pump Feed 3 Cartridge Fuse 30 Amp Green B.
Cavity Fuse Cir cuits 10 Cartridge Fuse 30 Amp Green Batt-Switch, Ignition (Run/Start/ Accy) 1 1 Mini Fuse 20 Amp Y ellow Batt-Relay Contact, Auto Shut- down 12 Mini Fuse 20 Amp Y ellow Secondary Powe.
Cavity Fuse Cir cuits 22 Mini Fuse 15 Amp Blue Battery to AC Clutch Relay 23, 24 Mini Fuse 10 Amp Red Airbag, Ignition Run 25-29 ISO RE- LA Y Batt-Relay Contact, High Blower Motor 30-34 MICRO RELA Y B.
Cavity Fuse Cir cuits 70, 71 Mini Fuse 20 Amp Y ellow Right HID Headlamp 72-76 MICRO RELA Y Batt-Run/Acc Relay 82-86 MICRO RELA Y Heated Rear W indow (EBL) Re- lay 87-91 MICRO RELA Y Batt-Motor , Fuel Pump Relay VEHICLE STORAGE W e recommend that you follow these guidelines befor e storing your vehicle for extended periods.
the vehicle is not going to be driven in the next 3 weeks, follow the battery rechar ge procedur e in the Service Manual, then disconnect the battery at the negative terminal or use the save feature described in Maintaining your V ehicle section under the Mainte- nance Procedur es sub-section, within Maintenance- Free Battery .
• Cut blocks of plywood about the same size of the tires. Cover each block with indoor/outdoor carpeting and place them between the tires and concr ete. This will prevent tir e flat spotting. • For long term storage, remove the tir es and put the vehicle up on blocks.
Exterior Light Bulbs Headlight-Low/High Beam .... S e r viced at dealer only Aux. Headlight-High Beam ......... (HB3A) 9005XS Front Park/T urn ...................... 3157AK Fog Light ....................... (H10 U) 9145 Front Sidemarker ..............
2. T wist off sockets counter-clockwise and pull out bulbs from the socket, install the new bulbs, and r einstall the bulb and socket assembly . Replace the splash shield. NOTE: On vehicles equipped with High Intensity Dis- charge Headlights (HID), when the headlights ar e turned on there is a blue hue to the lights.
High Intensity Discharge Headlights (HID) The headlights are a type of high voltage dischar ge tube. High voltage can remain in the cir cuit even with the headlight switch off and the key r emoved. Because of this, you should not attempt to service a headlight bulb yourself.
2. T wist sockets counter-clockwise to pull out bulbs. Replace tail, tail/stop, or marker lamp bulb. 3. Reinstall the appropriate bulb and socket assembly . Replace the access panel. Close the trunk. Backup and Rear T urn Signal Lamp Bulb Replacement 1.
2. Remove three plastic nuts from the upper lamp assem- bly . MAINT AINING YOUR VEHICLE 209 7.
3. T wist sockets of the three bulbs shown counter- clockwise. Disconnect bulb and socket assemblies from the upper lamp assembly . Pull the upper lamp assembly clear in order to access backup and r ear turn signal lamp bulbs. 4. Replace the backup or r ear turn signal lamp bulb.
License Plate Light T wist off sockets counter -clockwise and pull out bulbs. Replace as requir ed. MAINT AINING YOUR VEHICLE 21 1 7.
Headlight Aiming The headlights on your new V iper were aimed at the factory . The factory setting was made at a no load setting. A gr eat increase in weight will change the aiming and it may be necessary to readjust the headlights if you typically carry an excessive amount of weight in the trunk or otherwise suspect misalignment.
RECOMMENDED FLUIDS, LUBRICANTS AND GENUINE P ARTS Engine Component Fluid, Lubricant, or Genuine Part Engine Coolant Mopar 威 Antifreeze/Coolant 5 Y ear/102,000 Mile Formula HOA T (Hybrid Or- ganic Additive T echnology) Engine Oil Use API rated SL/CF full synthetic engine oil.
Chassis Component Fluid, Lubricant, or Genuine Part T ransmission Mopar Synthetic Manual T ransmission Lubricant SAE 75W -85 (Castrol Syn- torq L T 75W/85) Rear Axle Mopar Synthetic Gear and Axle Lubr.
Body Component Fluid, Lubricant, or Genuine Part Hinges: Door , T runk & Hood Springs and Links Mopar 威 Spray White Lube Latches: Door , Hood & T runk Mopar 威 Multi-Purpose Lube NLGI Grade 2 Door Hinge Check Spring Lubriplate Mo-Lith No.
.
MAINTENANCE SCHEDULES CONTENTS 䡵 Emission Control System Maintenance ........ 2 1 8 䡵 Maintenance Schedules ................... 2 1 8 ▫ Schedule “ B ” .
EMISSION CONTROL SYSTEM MAINTENANCE The “ Scheduled ” maintenance services, listed in bold type must be done at the times or mileages specified to assure the continued pr oper functioning of the emission control system.
• T axi, police, or delivery service (commercial ser - vice). 〫 • Off-r oad or desert operation. • If equipped for and operating with E-85 (ethanol) fuel.
At Each Stop for Fuel • Check the engine oil level about 5 minutes after a fully warmed engine is shut off. Checking the oil level while the vehicle is on level ground will impr ove the accu- racy of the oil level reading. Add oil only when the level is at or below the ADD or MIN mark.
SCHEDULE “ B ” Follow schedule “ B ” if you usually operate your vehicle under one or more of the following conditions. • Day or night temperatures ar e below 32 ° F( 0 ° C). • Stop and go driving. • Extensive engine idling. • Driving in dusty conditions.
Miles 3,000 6,000 9,000 12,000 15,000 18,000 (Kilometers) (5 000) (10 000) (14 000) (19 000) (24 000) (29 000) Change engine oil and engine oil filter , if not replaced at 3 months. XXXXX X Inspect the brake linings. X Change the rear axle fluid. X Inspect and replace, if necessary , the air cleaner filter .
Miles 21,000 24,000 27,000 30,000 33,000 36,000 (Kilometers) (34 000) (38 000) (43 000) (48 000) (53 000) (58 000) Change engine oil and engine oil filter , if not replaced at 3 months. XXXXX X Lubricate the front and r ear suspension ball joints. X Inspect the brake linings.
Miles 39,000 42,000 45,000 48,000 51,000 54,000 (Kilometers) (62 000) (67 000) (72 000) (77 000) (82 000) (86 000) Change engine oil and engine oil filter , if not replaced at 3 months. XXXXX X Lubricate the front and r ear suspension ball joints. X Inspect the brake linings.
Miles 57,000 60,000 63,000 66,000 69,000 72,000 (Kilometers) (91 000) (96 000) (101 000) (106 000) (1 10 000) (115 000) Change engine oil and engine oil filter , if not re- placed at 3 months. XXXXX X Lubricate the front and r ear suspension ball joints.
Miles 75,000 78,000 81,000 84,000 87,000 90,000 (Kilometers) (120 000) (125 000) (130 000) (134 000) (139 000) (144 000) Change engine oil and engine oil filter , if not replaced at 3 months. XXXXX X Lubricate the front and r ear suspension ball joints.
Miles 93,000 96,000 99,000 102,000 105,000 (Kilometers) (149 000) (154 000) (158 000) (163 000) (168 000) Change engine oil and engine oil filter , if not replaced at 3 months. XXXXX Inspect the brake linings. X Change the rear axle fluid. X Inspect and replace, if necessary , the engine air cleaner filter .
SCHEDULE “ A ” Miles 6,000 12,000 18,000 24,000 30,000 36,000 (Kilometers) (10 000) (19 000) (29 000) (38 000) (48 000) (58 000) [Months] [6] [12] [18] [24] [30] [36] Change engine oil and engine oil filter . X XXXXX Change the rear axle fluid. X X Inspect the brake linings.
Miles 42,000 48,000 54,000 60,000 66,000 (Kilometers) (67 000) (77 000) (86 000) (96 000) (106 000) [Months] [42] [48] [54] [60] [66] Change engine oil and engine oil filter . X X X X X Inspect the brake linings. X Change the rear axle fluid. X Inspect and replace, if necessary , the engine air cleaner filter .
Miles 72,000 78,000 84,000 90,000 96,000 102,000 (Kilometers) (1 15 000) (125 000) (134 000) (144 000) (154 000) (163 000) [Months] [72] [78] [84] [90] [96] [102] Change engine oil and engine oil filter . XXXXXX Inspect the brake linings. X X Inspect and replace, if necessary , the engine air cleaner filter .
* This maintenance is recommended by DaimlerChrysler Corporation to the owner but is not requir ed to maintain the warranty on the PCV orifice. ‡ This maintenance is not requir ed if previously r eplaced. Inspection and service should also be performed anytime a malfunction is observed or suspected.
.
IF YOU NEED CONSUMER ASSIST ANCE CONTENTS 䡵 Suggestions For Obtaining Service For Y our V ehicle .............................. 2 3 4 ▫ Prepar e For The Appointment ............ 2 3 4 ▫ Prepar e A List ........................ 2 3 4 ▫ Be Reasonable W ith Requests .
SUGGESTIONS FOR OBT AINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment If you ’ re having warranty work done, be sur e to have the right papers with you. T ake your warranty folder . All work to be performed may not be covered by the warranty , discuss additional charges with the service manager .
IF YOU NEED ASSIST ANCE The manufacturer and its dealers ar e vitally interested in your satisfaction. W e want you to be happy with our products and services. W arranty service must be done by an authorized Chrysler , Dodge, or Jeep dealer . W e strongly r ecommend that you take your vehicle to you selling dealer .
DaimlerChrysler Motors Corporation Customer Center P .O. Box 21 – 8004 Auburn Hills, MI 48321 – 8004 Phone: (800) 992-1997 DaimlerChrysler Canada Inc. Customer Center P .O. Box 1621 W indsor , Ontario N9A 4H6 Phone — (800) 465 – 2001 In Mexico contact: A v .
contract, call the manufacturer ’ s Service Contract Na- tional Customer Hotline at 1-800-521-9922. The manufacturer will not stand behind any service contract that is not the manufacturer ’ s Service Contract. It is not responsible for any service contract other than the manufacturer ’ s Service Contract.
U.S. ONL Y 238 IF YOU NEED CONSUMER ASSIST ANCE.
MOP AR 姞 P ARTS Mopar 威 fluids, lubricants, parts, and accessories are available from your dealer . They will help you keep your vehicle operating at its best.
PUBLICA TION ORDER FORMS T o order the following manuals, you may use either the website or the phone numbers listed below . V isa, Mas- tercar d, American Express, and Discover or ders are ac- cepted. If you prefer mailing your payment, please call for an order form.
Call T oll Free at 1 – 800 – 890 – 4038 (U.S.) or 1 – 800 – 387 – 1 143 (Canada) Or V isit us on the W orld W ide W eb at: www .techauthority .
W ARNING! The traction grade is based on braking (straight- ahead) traction tests and does not include cornering (turning) performance. T emperature Grades The temperature grades ar e A (highest), B, .
INDEX 10.
About Y our Brakes ....................... 1 1 7 ABS (Anti-Lock Brake) System ............... 8 7 Accessory Delay , Power .................. 13,26 Adding Engine Coolant (Antifreeze) .......... 1 8 5 Adding Fuel ........................... 1 4 5 Adding W asher Fluid .
Gas Caution .......................... 1 7 3 Jump Starting ......................... 1 5 0 Keyless T ransmitter Replacement ............ 1 9 Bearings .............................. 1 9 4 Belt System, Six Point ..................... 3 2 Belts, Drive ..
Charging System Light ..................... 9 0 Chart, T ire Sizing ........................ 1 2 3 Check Engine Light (Malfunction Indicator Light) . 162 Checks, Safety ........................... 5 1 Child Restraint ........................ 34,39 Child Restraint T ether Anchors .
Defroster , W indshield ...................... 5 1 Delay (Intermittent) W ipers ................. 8 2 Diagnostic System, Onboard ................ 1 6 1 Dimmer Control ......................... 7 4 Dimmer Switch, Headlight .................. 7 8 Disposal Antifreeze (Engine Coolant) .
Engine Oil V iscosity ................... 166,212 Engine Oil V iscosity Chart ................. 1 6 6 Exhaust Gas Caution ................ 51,145,182 Exhaust System ......................... 1 8 2 Exterior Lights .......................... 2 0 5 F a n .
Fuses ................................ 1 9 7 G a s C a p .............................. 1 4 5 Gasoline .............................. 1 4 2 Gasoline, Clean Air ...................... 1 4 2 Gasoline, Reformulated ................... 1 4 2 Gasoline/Oxygenate Blends .
Inside Rearview Mirror .................... 6 7 Instrument Cluster ........................ 8 6 Instrument Panel and Contr ols ............... 8 5 Instrument Panel Lens Cleaning ............. 1 9 5 Interior and Instrument Lights .......... See Lights Interior Lighting .
High Beam Indicator .................... 8 9 Instrument Cluster ...................... 7 5 Interior .............................. 7 4 License ............................. 2 1 1 Lights On Reminder ..................... 7 6 Malfunction Indicator .....
Outside .............................. 6 8 Rearview ............................. 6 7 Modifications/Alterations, V ehicle ............. 7 Mopar Parts ......................... 163,239 Multi-Function Control Lever ................ 7 4 New V ehicle Break-In Period .
Distribution Center ..................... 1 9 7 Steering .......................... 121,178 W indows ............................. 2 4 Pregnant W omen and Seat Belts .............. 3 3 Programming T ransmitters .................. 1 8 Radial Ply T ires .
Scheduled Maintenance ................... 1 6 4 Seat Belt Maintenance .................... 1 9 6 Seat Belt Reminder ..................... 31,89 Seat Belts ............................ 26,27 And Pregnant W omen ................... 3 3 Child Restraint .
Steering Linkage ............................. 1 8 0 Power ........................... 121,178 T ilt Column ........................... 7 8 Storage ............................... 2 0 2 Stuck, Freeing .......................... 1 5 5 Supplemental Restraint System - Airbag .
Disabled V ehicle ....................... 1 5 5 T railering ............................ 1 4 6 T raction .............................. 1 5 4 T railer T owing .......................... 1 4 6 T ransmission ........................... 1 9 3 Fluid .....
W ind Buffeting .......................... 2 6 W indows .............................. 2 4 Power ............................... 2 4 W indshield Defroster ...................... 5 1 W indshield W ashers .................. 81,82,182 W indshield W ipers .
NOTES.
NOTES.
NOTES.
NOTES.
NOTES.
NOTES.
NOTES.
デバイスDodge 2005 Viperの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Dodge 2005 Viperをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはDodge 2005 Viperの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Dodge 2005 Viperの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Dodge 2005 Viperで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Dodge 2005 Viperを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はDodge 2005 Viperの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Dodge 2005 Viperに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちDodge 2005 Viperデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
