Dodgeメーカー2007 LX Magnumの使用説明書/サービス説明書
ページ先へ移動 of 400
T ABLE OF CONTENTS SECTION P AGE 1 INTRODUCTION ............................................................. 3 2 THINGS TO KNOW BEFORE ST AR TING YOUR VEHICLE ........................... 9 3 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE ..............
.
INTRODUCTION CONTENTS 䡵 Introduction ........................... 4 䡵 How T o Use This Manual ................. 4 䡵 W arnings And Cautions .................. 6 䡵 V ehicle Identification Number .............. 6 䡵 V ehicle Modifications / Alterations .
INTRODUCTION This manual has been prepar ed with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your new vehicle. It is supplemented by a W arranty Information Booklet and various customer oriented documents.
INTRODUCTION 5 1.
W ARNINGS AND CAUTIONS This manual contains W ARNINGS against operating procedur es, which could result in an accident or bodily injury . It also contains CAUTIONS against procedures, which could result in damage to your vehicle. If you do not read this entir e manual, you may miss important information.
VEHICLE MODIFICA TIONS / AL TERA TIONS W ARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death.
.
THINGS T O KNOW BEFORE ST ARTING YOUR VEHICLE CONTENTS 䡵 A W ord About Y our Keys ................. 1 1 ▫ Ignition Key Removal ................... 1 1 ▫ Key-In-Ignition Reminder ................ 1 2 䡵 Sentry Key ............................ 1 3 ▫ Replacement Keys .
▫ Child Protection Door Lock ............... 2 5 䡵 W indows ............................. 2 7 ▫ Power W indows ....................... 2 7 ▫ W ind Buffeting ........................ 3 0 䡵 Liftgate .............................. 3 1 䡵 Occupant Restraints .
A WORD ABOUT YOUR KEYS Y ou can insert the double-sided keys into the locks with either side up. The dealer that sold you your new vehicle has the key code numbers for your vehicle locks. These numbers can be used to order duplicate keys fr om your dealer .
• For vehicles equipped with the Electronic V ehicle Information Center (EVIC), the power window switches, radio, power sunroof (if equipped), and power outlets will remain active for up to 60 minutes after the ignition switch is turned off. Opening either front door will cancel this featur e.
SENTR Y KEY The Sentry Key Immobilizer System prevents unautho- rized vehicle operation by disabling the engine. The system does not need to be armed or activated.
All of the keys provided with your new vehicle have been programmed to the vehicle electr onics. Replacement Keys NOTE: Only keys that are pr ogrammed to the vehicle electronics can be used to start and operate the vehicle. Once a Sentry Key is programmed to a vehicle, it cannot be programmed to any other vehicle.
The new Sentry Key is programmed. The Keyless Entry T ransmitter will also be programmed during this pro- cedure. Repeat this procedur e to program up to 8 keys.
system is not arming. In addition, if you open a door during the arming period, the system will cancel the arming process. If you wish to r earm the system after closing the door , you must repeat one of the pr eviously described arming sequences.
T amper Alert If something has triggered the system in your absence, the horn will sound three times when you disarm the system. Check the vehicle for tampering. ILLUMINA TED ENTRY SYSTEM The courtesy lights will turn on when you use the keyless entry transmitter or open the doors or liftgate.
T o unlock the doors: Press and r elease the UNLOCK button on the transmitter once to unlock the driver’s door , or twice to unlock all doors. The turn signal lights will flash to acknowledge the unlock signal. The illuminated entry system will also turn on.
• For vehicles equipped with the Electronic V ehicle Information Center (EVIC), refer to “Flash Lights with Remote Key Lock,” under ⬙ Personal Settings (Cus- tomer Programmable Featur es),” under “Electronic V ehicle Information Center (EVIC)” in Section 4 of this manual for details.
Sound Horn with Remote Key Lock This feature will cause the horn to chirp when the doors are locked with the transmitter . This feature can be turned on or off.
NOTE: • The interior lights will turn off if you turn the ignition switch to the ACC or ON position while the panic alarm is activated. However , the exterior lights and horn will remain on.
4. T o assemble the transmitter case, snap the two halves together . If so equipped, install and tighten the screw until snug. Make sure ther e is an even “gap” between the two halves. 5. T est the transmitter operation. General Information This device complies with part 15 of the FCC rules and RSS 210 of Industry Canada.
If the door lock plunger is down when you shut the door , the door will lock. Therefor e, make sure the keys ar e not inside the vehicle before closing the door . W ARNING! • For personal security and safety in the event of an accident, lock the vehicle doors as you drive as well as when you park and leave the vehicle.
chime will sound if the key is in the LOCK or ACC position and a door is open, as a reminder to r emove the key . Automatic Door Locks The doors will lock automatically on vehicles with power door locks if all of the following conditions are met: 1. The Automatic Door Locks feature is enabled.
Automatic Unlock Doors on Exit The doors will unlock automatically on vehicles with power door locks if: 1. The Automatic Unlock Doors On Exit featur e is en- abled. 2. The transmission was in gear and the vehicle speed returned to 0 mph (0 km/h). 3. The transmission is in NEUTRAL or P ARK.
T o Engage the Child Protection Door Lock 1. Open the rear door . 2. Insert the tip of the vehicle’s ignition key or alike into the child lock control and pull it upwar d.
2. Insert the tip of the vehicle’s ignition key or alike into the child lock control and pull it downwar d. 3. Repeat Steps 1 and 2 on the opposite rear door . NOTE: After disengaging the child protection door lock system, always test the door from the inside to make certain it is in the desired position.
W ARNING! Never leave children in a vehicle, with the keys in the ignition switch. Occupants, particularly unat- tended children, can become entrapped by the win- dows while operating the power window switches. Such entrapment may result in serious injury or death.
T o close the window part way , lift the window switch to the first detent and release it when you want the window to stop. For vehicles not equipped with the Electronic V ehicle Information Center (EVIC), the power window switches will remain active for 10 minutes after the ignition switch is turned off.
W indow Lockout Switch The window lockout switch on the driver’s door allows you to disable the window controls on the passenger doors. When the switch is pressed, the window contr ols on the passenger doors will not illuminate and the passenger windows will be disabled.
buffeting occurs with the sunr oof open, then adjust the sunroof opening to minimize the buf feting. LIFTGA TE The liftgate can be unlocked or locked by the remote keyless entry transmitter or by activating the power door lock switches located on the front doors.
NOTE: If a power malfunction occurs, you can use the emergency liftgate latch r elease to open the liftgate. The emergency liftgate latch r elease is located behind a snap-in cover on the liftgate trim panel. W ARNING! • Driving with the liftgate open can allow poison- ous exhaust gases into your vehicle.
OCCUP ANT RESTRAINTS Some of the most important safety features in your vehicle are the r estraint systems. These include the front and rear seat belts for the driver and all passengers, fr ont airbags for both the driver and front passenger and, if so equipped, side curtain airbags for the driver and passen- gers seated next to a window .
W ARNING! • It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. • Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts.
3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” W ARNING! • A belt that is buckled into the wrong buckle will not protect you properly . The lap portion could ride too high on your body , possibly causing internal injuries.
4. Position the lap belt across your thighs, below your abdomen. T o remove slack in the lap belt portion, pull up a bit on the shoulder belt. T o loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt. A snug belt reduces the risk of sliding under the belt in a collision.
W ARNING! A frayed or torn belt could rip apart in a collision and leave you with no protection. Inspect the belt system periodically , checking for cuts, frays, or loose parts. Damaged parts must be replaced immediately . Do not disassemble or modify the system.
As a guide, if you are shorter than average, you will prefer a lower position, and if you ar e taller than average, you will prefer a higher position. When you r elease the anchorage, try to move it up and down to make sure that it is locked in position.
NOTE: These devices are not a substitute for pr oper seat belt placement by the occupant. The seat belt still must be worn snugly and positioned properly . The pretensioners ar e triggered by the Airbag Control Module (refer to information on Airbags in this section).
NOTE: W atch for the Seat Belt Reminder Light to turn on while unbuckling the seat belt and turn off while re-buckling the seat belt. It may be necessary to r etract the seat belt. 4. T urn the ignition switch to the LOCK position. A single chime will sound to signify that you have success- fully completed the programming.
Pregnant women should wear the lap part of the belt across the thighs and as snug acr oss the hips as possible. Keep the belt low so that it does not come across the abdomen. That way the strong bones of the hips will take the force if ther e is a collision.
NOTE: The front airbags ar e certified to the Federal regulations that allow less for ceful deployment. The front airbags have a multistage inflator design. This may allow the airbag to have differ ent rates of inflation that are based on collision severity .
W ARNING! • Do not put anything on or around the front airbag covers or attempt to manually open them. Y ou may damage the airbags and you could be injured be- cause the airbags are no longer functional. These protective covers for the airbag cushions are de- signed to open only when the airbags are inflating.
Here are some simple steps you can take to minimize the risk of harm from a deploying airbag. 1. Children 12 years old and under should ride buckled up in the rear seat. 2. Infants in rear -facing child restraints should NEVER ride in the front seat of a vehicle with a passenger fr ont airbag.
W ARNING! • Relying on the airbags alone could lead to more severe injuries in a collision. The airbags work with your seat belt to restrain you properly . In some collisions, the airbags won’t deploy at all. Always wear your seat belts even though you have airbags.
How The Airbag System W orks • The Airbag Control Module (ACM) determines if a frontal collision is sever e enough to requir e the airbags to inflate. The front airbag inflators ar e designed to provide dif ferent rates of airbag inflation from dir ec- tion provided by the ACM.
their full size. The bags fully inflate in about 50 - 70 milliseconds. This is about half of the time that it takes to blink your eyes. The bags then quickly deflate while helping to restrain the driver and fr ont passenger . The driver’s front airbag gas is vented thr ough vent holes in the sides of the airbag.
you might get sliding along a carpet or gymnasium floor . They are not caused by contact with chemicals. They are not permanent and normally heal quickly . However , if you haven’t healed significantly within a few days, or if you have any blistering, see your doctor immediately .
Maintaining Y our Airbag System W ARNING! • Modifications to any part of the airbag system could cause it to fail when you need it. Y ou could be injured because the airbags are not there to protect you.
the electronic data may be used by DaimlerChrysler and others to learn more about the possible causes of crashes and associated injuries in order to assess and impr ove vehicle performance.
• Brake status (service and parking brakes) • Accelerator status (including vehicle speed) • Engine control status (including engine speed) • Cruise contr ol status (if applicable) • T raction/stability control status (if applicable) Child Restraint Everyone in your vehicle needs to be buckled up all the time — babies and children, too.
one year old and weigh at least 20 lbs (9 kg). T wo types of child restraints can be used r earward-facing: infant carriers and “convertible” child seats. • The infant carrier is only used rearwar d-facing in the vehicle. It is recommended for childr en who weigh up to about 20 lbs (9 kg).
Children T oo Large For Booster Seats Children who ar e large enough to wear the shoulder belt comfortably , and whose legs are long enough to bend over the front of the seat when their back is against the seat back, should use the lap/shoulder belt in a rear seat.
• The restraint must be appr opriate for your child’s weight and height. Check the label on the restraint for weight and height limits. • Carefully follow the instr uctions that come with the restraint. If you install the r estraint improperly , it may not work when you need it.
rear -seating positions, or if your child restraints ar e not LA TCH-compatible, install the restraints using the vehi- cle’s seat belts. Installing the LA TCH-Compatible Child Restraint System W e urge that you car efully follow the directions of the manufacturer when installing your child r estraint.
cover directly behind the seat wher e you are placing the child restraint and attach the tether strap to the anchor - age, being careful to r oute the tether strap to provide the most direct path between the anchor and the child restraint.
keep the belt tight, however , any seat belt system will loosen with time, so check the belt occasionally , and pull it tight if necessary . Seat belts with an automatic locking retractor have a distinctive label on the seat belt webbing.
T o attach a child restraint tether strap: 1. Route the tether strap to provide the most dir ect path for the strap between the anchor and the child seat. 2. Attach the tether strap hook of the child restraint to the tether anchor and remove slack in the tether strap according to the child r estraint manufacturer’s instruc- tions.
ENGINE BREAK-IN RECOMMENDA TIONS A long break-in period is not r equired for the engine in your new vehicle. Drive moderately during the first 300 miles (500 km). After the initial 60 miles (100 km), speeds up to 50 or 55 mph (80 or 90 km/h) are desirable.
Lock Y our V ehicle Always remove the keys fr om the ignition and lock all doors when leaving the vehicle unattended, even in your own driveway or garage. T ry to park your vehicle in a well-lit area and never invite theft by leaving articles of value exposed.
Safety Checks Y ou Should Make Inside The V ehicle Seat Belts Inspect the belt system periodically , checking for cuts, frays and loose parts. Damaged parts must be replaced immediately . Do not disassemble or modify the system. Front seat belt assemblies must be r eplaced after a collision.
Fluid Leaks Check area under vehicle after overnight parking for fuel, engine coolant, oil, or other fluid leaks. Also, if gasoline fumes are detected or if fuel, power steering fluid, or brake fluid leaks are suspected, the cause should be located and corrected immediately .
UNDERST ANDING THE FEA TURES OF YOUR VEHICLE CONTENTS 䡵 Mirrors .............................. 6 7 ▫ Inside Day/Night Mirror ................. 6 7 ▫ Automatic Dimming Inside Mirror — If Equipped ............................ 6 7 ▫ Outside Mirrors .
▫ Lumbar Support — If Equipped ............ 9 2 ▫ Head Restraints ....................... 9 2 ▫ Heated Seats — If Equipped .............. 9 2 ▫ Folding Rear Seat ...................... 9 4 䡵 T o Open And Close The Hood ............. 9 5 䡵 Lights .
▫ T o V ary The Speed Setting ............... 1 0 8 ▫ T o Accelerate For Passing ............... 1 0 8 䡵 Overhead Console ..................... 1 0 9 ▫ Courtesy/Reading Lights ................ 1 0 9 ▫ Sunglasses Storage .................... 1 0 9 䡵 Garage Door Opener (HomeLink 威 )—I f Equipped .
䡵 Roof Luggage Rack — If Equipped ......... 1 2 9 䡵 Load Leveling System — If Equipped ....... 1 3 1 66 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE.
MIRRORS Inside Day/Night Mirror Adjust the mirror to center on the view thr ough the rear window . A two-point pivot system allows for horizontal and vertical mirror adjustment. Annoying headlight glare can be r educed by moving the small control under the mirr or to the night position (toward r ear of vehicle).
CAUTION! T o avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror . Apply the solution onto a clean cloth and wipe the mirror clean.
Power Remote-Control Mirrors The power mirror switch is located on the driver’s door trim panel next to the power door lock switch. A rotary knob selects the left mirror , right mirror , or off position. After selecting a mirror , move the knob in the same direction you want the mirr or to move.
HANDS–FREE COMMUNICA TION (UConnect™) — IF EQUIPPED UConnect™ is a voice-activated, hands-free, in- vehicle communications system. UConnect™ allows you to dial a phone number with your cellular phone using simple voice commands (e.g., ⬙ Call” ѧ “Mike” ѧ ”W ork ⬙ or ⬙ Dial” ѧ “248-555-1212 ⬙ ).
The UConnect™ system can be used with any Hands- Free Pr ofile certified Bluetooth™ cellular phone. See www .chrysler .com/uconnect for supported phones. If your cellular phone supports a differ ent profile (e.g., Headset Profile), you may not be able to use any UCon- nect™ features.
• For each feature explanation in this section, only the combined form of the voice command is given. Y ou can also break the commands into parts and say each part of the command, when you are asked for it.
• www .jeep.com/uconnect The following are general phone to UConnect™ System pairing instructions: • Press the ’Phone’ button to begin. • After the ⬙ Ready ⬙ prompt and the following beep, say ⬙ Setup Phone Pairing ⬙ and follow the audible prompts.
• The UConnect™ system will confirm the phone num- ber and then dial. The number will appear in the display of certain radios. Call/Dial by Saying a Name • Press the “Phone” button to begin. • After the ⬙ Ready ⬙ prompt and the following beep, say “Dial” or Call.
The UConnect™ system will allow you to enter up to 32 names in the phonebook with each name having up to four associated phone numbers and designations.
from which you choose. T o select one of the entries from the list, pr ess the ⬙ V oice Recognition ⬙ button while the UConnect™ system is playing the desired entry and say ⬙ Delete. ⬙ • After you enter the name, the UConnect™ system will ask you which designation you wish to delete, home, work, mobile, or pager .
Phone Call Features The following features can be accessed thr ough the UConnect™ system if the feature(s) ar e available on your cellular service plan. For example, if your cellular service plan provides thr ee-way calling, this feature can be accessed through the UConnect™ system.
indicating that the active and hold status of the two calls have switched. Only one call can be placed on hold at one time. Conference Call When two calls are in pr ogress (one active and one on hold), press and hold the ’Phone’ button until you hear a double beep indicating that the two calls have been joined into one conference call.
• After ignition key is switched to off, a call can continue on the UConnect™ system for certain duration, after which the call is automatically transferred fr om the UConnect™ system to the mobile phone. • An active call is automatically transferred to the mobile phone after ignition key is switched to off.
Canada and 060 for Mexico). The number dialed may not be applicable with the available cellular service and area. The UConnect™ system does slightly lower your chances of successfully making a phone call as to that for the cell phone directly .
When calling a number with your UConnect™ system that normally requir es you to enter in a touch-tone sequence on your cellular phone keypad, you can push the ’V oice Recognition’ button and say the sequence you wish to enter followed by the word ⬙ Send.
Dialing Using the Cellular Phone Keypad Y ou can dial a phone number with your cellular phone keypad and still use the UConnect™ system (while dialing via the cell phone keypad, the user must exercise caution and take precautionary safety measur es).
Connect or Disconnect Link Between the UConnect™ System and Cellular Phone Y our cellular phone can be paired with many dif ferent electronic devices, but can only be actively ⬙ connected ⬙ with one electronic device at a time.
Delete UConnect™ Paired Cellular Phones • Press the ’Phone’ button to begin. • After the ⬙ Ready ⬙ prompt and the following beep, say ⬙ Setup Phone Pairing.
• UConnect™ phonebook nametag recognition rate is optimized for the voice of the person who stored the name in the phonebook. • Y ou can say ⬙ O ⬙ (letter ⬙ O ⬙ ) for ⬙ 0 ⬙ (zero).
86 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE.
UNDERST ANDING THE FEA TURES OF YOUR VEHICLE 87 3.
88 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE.
North American English Primary Alternate(s) Zero Oh Add location Add new All All of them Confirmation prompts Confirmations prompts Delete a name Delete Language Select language List names List all List paired phones List phones Pager Beeper Phone pairing Pairing Phonebook Phone book Return to main menu Return.
W ARNING! • Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured. Adjust the seat only while the vehicle is parked.
CAUTION! Do not place any article under a power seat as it may cause damage to the seat controls. Power Reclining Seats — If Equipped The recliner contr ol is located on the outboard side of the seat. W ARNING! Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest.
Lumbar Support — If Equipped This feature allows you to incr ease or decrease the amount of lumbar support. T urn the control lever for - ward to incr ease and rearward to decr ease the desired amount of lumbar support. Head Restraints Head restraints can r educe the risk of whiplash injury in the event of impact from the r ear .
The controls for each heater ar e located near the bottom center of the instrument panel. After turning on the ignition, you can choose from High, Of f, or Low heat settings. Amber LEDs in the top portion of each switch indicate the level of heat in use.
Folding Rear Seat The rear seatbacks can be folded forwar d to provide an additional storage area. Pull on the loops shown in the illustration to fold down either or both seatbacks.
TO OPEN AND CLOSE THE HOOD T wo latches must be released to open the hood. First, pull the hood release lever located under the left side of the instrument panel. Next, move to the outside of the vehicle and push the safety catch to the left. The safety catch is located under the center front edge of the hood.
W ARNING! If the hood is not fully latched, it could fly up when the vehicle is moving and block your forward vision. Y ou could have a collision. Be sure all hood latches are fully latched before driving. LIGHTS Headlight Switch The headlight switch is located on the left side of the instrument panel.
headlights will stay ON for up to 90 seconds after you turn the ignition switch OFF . T o turn the Automatic System OFF , move the headlight switch out of the AUTO (A) position. NOTE: The engine must be running befor e the head- lights will come ON in the Automatic mode.
If you turn the headlights, park lights, or ignition switch on again, the system will cancel the delay . If you turn the headlights off befor e the ignition, they will turn off in the normal manner .
Multi-Function Lever The multi-function lever controls the operation of the turn signals, headlight beam selection, and passing lights. The lever is located on the left side of the steering column.
Overhead Console Map/Reading Lights These lights are mounted between the sun visors on the overhead console. Each light is turned ON by pr essing the lens.
Interior light Defeat (OFF) Rotate the dimmer control to the extr eme bottom “OFF” position. The interior lights will remain of f when the doors are open. Parade Mode (Daytime Brightness Feature) Rotate the dimmer control upwar d to the first detent.
CAUTION! T urn the windshield wipers off when driving through an automatic car wash. Damage to the windshield wipers may result if the wiper switch is left in any position other than OFF . Intermittent Wiper System Use the intermittent wiper when weather conditions make a single wiping cycle with a variable pause be- tween cycles desirable.
two wipe cycles after releasing the lever and then r esume the intermittent interval previously selected. If you activate the washer while the windshield wiper is turned OFF , the wipers will operate for two wipe cycles and then turn OFF .
The fluid reservoir will hold nearly 1 gallon (4 liters) of washer fluid when the message “Low W asher Fluid” appears in the Electronic V ehicle Information Center (EVIC) — if equipped. W ARNING! Commercially available windshield washer solvents are flammable.
T o unlock the steering column, pull the control handle outward. T o tilt the steering column, move the steering wheel upward or downwar d as desired. T o lengthen or shorten the steering column, pull the steering wheel outward or push it inwar d as desired.
Press the switch forwar d to move the pedals forward (toward the fr ont of the vehicle). Press the switch r earward to move the pedals r earward (toward the driver). • The pedals can be adjusted with the ignition OFF . • The pedals can be adjusted while driving.
T o Activate: Push the speed control lever inwar d (toward the steering column) and release (“ON/OFF”). The indicator light in the lever (and in the instrument cluster on some models) will illu- minate to show that the speed control system is ON. T o turn the system OFF , push the lever inward (towar d the steering column) again and release.
speed. T o do so, push the lever up and release (RES/ ACCEL), and then remove your foot fr om the accelerator pedal. T o V ary the Speed Setting: When the speed control is set, you can incr ease speed by pushing the lever up and holding (“RES/ACCEL”).
OVERHEAD CONSOLE The overhead console contains courtesy/r eading lights, an optional universal garage door opener (HomeLink 威 ), storage for sunglasses, and an optional power sunroof switch. Courtesy/Reading Lights At the forward end of the console ar e two courtesy/ reading lights.
GARAGE DOOR OPENER (HomeLink 姞 )—I F EQUIPPED The HomeLink 威 Universal T ransceiver replaces up to three r emote controls (hand held transmitters) that oper - ate devices such as garage door openers, motorized gates, or home lighting. It triggers these devices at the push of a button.
Programming HomeLink NOTE: When programming a garage door opener , it is advised to park outside the garage. It is also recom- mended that you install a new battery in the hand-held transmitter of the device being programmed. This will allow for quicker training and accurate transmission of the radio-frequency signal.
1. Press and hold the two outer HomeLink buttons. Release the buttons only when the EVIC displays “Chan- nels Cleared” (after 20 seconds); however , do not hold the buttons for longer than 30 seconds. Do not repeat this step if programming a second or thir d hand-held trans- mitter to the remaining HomeLink buttons.
NOTE: If your garage door opener fails to respond to the programmed HomeLink 威 Universal T ransceiver , and your garage door opener is manufactured after 1995, it may have a multiple security code system (rolling code system).
NOTE: If programming a garage door opener or gate operator , it is advised to unplug the device during the ⬙ cycling ⬙ process to pr event possible overheating.
For questions or comments, contact HomeLink at: www .homelink.com or 1-800-355-3515 . Security If you sell your vehicle, be sure to erase the fr equencies by following the “Erasing HomeLink Buttons” instruc- tions in this section. This device complies with part 15 of FCC rules and with RSS-210 of Industry Canada.
W ARNING! • Never leave children in a vehicle, with the keys in the ignition switch. Occupants, particularly unat- tended children, can become entrapped by the power sunroof while operating the power sunroof switch. Such entrapment may result in serious injury or death.
Pinch Protect Override If a known obstruction (ice, debris, etc.) pr events closing, press the switch forwar d and hold for two seconds after the reversal occurs. This allows the sunr oof to move towards the closed position. NOTE: Pinch protection is disabled while the switch is pressed.
For vehicles equipped with the EVIC, the power sunroof switch will remain active for up to 60 minutes after the ignition switch is turned off. Opening either fr ont door will cancel this feature.
NOTE: If desired, the power outlet next to the ash receiver tray (if equipped) can be converted by your authorized dealer to provide power with the ignition switch in the LOCK position. The center console outlet is powered dir ectly from the battery (power available at all times).
The auxiliary outlet is also powered dir ectly from the battery (power available at all times). Items plugged into this outlet may discharge the battery and/or pr event engine starting. Electrical Outlet Use With Engine Off CAUTION! • Many accessories that can be plugged in draw power from the vehicle’s battery , even when not in use (i.
CUP HOLDERS Front Seat Cup Holders The cup holders are located in the forwar d edge of the center console. Rear Seat Cup Holders The rear seat cup holders ar e located in the center armrest between the rear seats.
STORAGE Console Features The center console contains a large storage bin. The storage bin contains a four-slot coin holder (designed to hold various size coins) and a rubber mat at the bottom of the bin for noise control. The bin is lar ge enough to hold a portable AC/DC converter to power laptops, games, or other electrical equipment.
The 60/40 split-folding rear seat pr ovides cargo-carrying versatility . The seatbacks fold down easily by pulling nylon tabs between the seatbacks and the bolsters. When the seats are folded down, they pr ovide a continuous, nearly flat extension of the removable tri-fold load floor .
Load Floor Partially Folded Load Floor Fully Folded 124 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE.
Rollaway T onneau Cover — If Equipped The removable r ollaway tonneau cover mounts in the cargo ar ea behind the top of the rear seats. The tonneau cover , when extended, covers the cargo ar ea to keep items out of sight. Notches in the trim panels near the liftgate opening secure the extended tonneau cover in place.
T o install the tonneau cover , position it in the vehicle so that the flat side of the housing faces upward. Then, insert either the left or the right spring-loaded post (located on the ends of the tonneau cover housing) into the left or the right front attachment point shown.
W aterproof Liner The optional waterproof liner can be placed over the lower load floor . Cargo Organizer The optional cargo or ganizer can also be placed into the lower load floor .
Cargo T ie-Down Hooks The tie-downs located on cargo ar ea floor and on the rear trim panels should be used to safely secure loads when vehicle is moving. W ARNING! • Cargo tie-down hooks are not safe anchors for a child seat tether strap. In a sudden stop or colli- sion, a hook could pull loose and allow the child seat to come loose.
• Place as much cargo as possible in fr ont of the rear axle. T oo much weight or improperly placed weight over or behind the rear axle can cause the r ear of the vehicle to sway . • Do not pile luggage or cargo higher than the top of the seatback.
T o adjust, remove, or install the cr ossbars, proceed as follows: 1. Flip the lever on the end of the crossbar upwar d. 2. T urn the lever counter clockwise to loosen the lower clamp. When the lower clamp is loose, turn it until the round side of the clamp completely faces away fr om the side rail.
CAUTION! • T o avoid damage to the roof rack and vehicle, do not exceed the maximum roof rack load capacity of 150 lbs (68 kg). Always distribute heavy loads as evenly as possible and secure the load appropriately .
.
UNDERST ANDING YOUR INSTRUMENT P ANEL CONTENTS 䡵 Instrument Panel And Controls ............ 1 3 7 䡵 Base Instrument Cluster ................. 1 3 8 䡵 Premium Instr ument Cluster — If Equipped . . 139 䡵 Instrument Cluster Descriptions .......
▫ Operation Instructions - CD Mode ......... 1 6 4 ▫ Operation Instructions - Auxiliary Mode ..... 1 6 6 ▫ Operating Instructions - Hands Fr ee Phone — If Equipped ........................... 1 6 7 ▫ Operating Instructions - Satellite Radio — If Equipped .
䡵 V ideo Entertainment System (Sales Code XR V) — If Equipped .......................... 1 8 3 䡵 Satellite Radio — If Equipped ............. 1 8 4 ▫ System Activation ..................... 1 8 4 ▫ Electronic Serial Number/Sirius Identification Number (ESN/SID) .
▫ Adding W asher Fluid .................. 2 0 2 ▫ Electric Rear W indow Defroster ........... 2 0 2 136 UNDERST ANDING YOUR INSTRUMENT P ANEL.
INSTRUMENT P ANEL AND CONTROLS 1 — Air Outlet 6 — Glove Box 1 1 — Ash T ray* 2 — Instrument Cluster 7 — Radio 12 — Ignition Switch 3 — Rear W iper/W asher Switch 8 — Climate Control 13.
BASE INSTRUMENT CLUSTER 138 UNDERST ANDING YOUR INSTRUMENT P ANEL.
PREMIUM INSTRUMENT CLUSTER — IF EQUIPPED UNDERST ANDING YOUR INSTRUMENT P ANEL 139 4.
INSTRUMENT CLUSTER DESCRIPTIONS 1. Fuel Gauge The pointer shows the level of fuel in the fuel tank when the ignition switch is in the ON position. 2. T rip Odometer Button Base Cluster The word ⬙ TRIP ⬙ will appear when this button is pr essed.
7. Electronic Thr ottle Control (ETC) Light This light will turn on briefly as a bulb check when the ignition switch is turned ON. This light will also turn on while the engine is running if ther e is a problem with the Elec- tronic Thr ottle Control system.
W ARNING! A hot engine cooling system is dangerous. Y ou or others could be badly burned by steam or boiling coolant. Y ou may want to call a service center if your vehicle overheats. If you decide to look under the hood yourself, see Section 7 of this manual.
and driving to the prevailing r oad conditions, and do not switch off the ESP or TCS — if equipped. (See page 230 for more information.) (See page 233 for mor e information.
18. Front Fog Light Indicator — If Equipped This light will turn on when the front fog lights are ON. (See page 98 for mor e information.) 19. Electronic V ehicle Information Center Display — If Equipped This display shows the Electronic V ehicle Information Center (EVIC) messages when the appropriate conditions exist.
NOTE: The light may flash momentarily during sharp cornering maneuvers, which change fluid level condi- tions. The vehicle should have service performed, and the brake fluid level checked. Immediate repair is necessary if brake failur e is indicated. W ARNING! Driving a vehicle with the brake light on is danger- ous.
vehicle placard or tir e inflation pressur e label. (If your vehicle has tires of a dif ferent size than the size indicated on the vehicle placard or tir e inflation pres- sure label, you should determine the pr oper tire inflation pressur e for those tires.
23. Anti-Lock Brake Light — If Equipped This light monitors the Anti-Lock Brake System. The light will turn on when the ignition switch is turned to the ON position and may stay on for as long as four seconds.
ELECTRONIC VEHICLE INFORMA TION CENTER (EVIC) – IF EQUIPPED The Electronic V ehicle Information Center (EVIC) fea- tures a driver -interactive display . It is located in the instrument cluster below the speedometer . V ehicles equipped with steering wheel mounted buttons (de- scribed in this section) are also equipped with the EVIC.
Press the FUNCTION SELECT button to accept a selection. The FUNCTION SELECT button also advances the radio to the next preset station, changes the side of the tape being played (if so equipped), or changes the current CD track being played (if so equipped) when the EVIC is in the Compass/T emp/Audio screen.
• Left/Right Front Door Ajar (one or more, with a single chime if speed is above 1 mph [1.6 km]) • Left/Right Rear Door Ajar (one or more, with a single chime if speed is above 1 mph [1.
V ehicles with the 5.7L Multi-Displacement System (MDS) may be equipped with the FUEL SA VER MODE in the T rip Functions of the EVIC. The FUEL SA VER MODE message will display above the average fuel economy in the EVIC display .
and average fuel economy , according to the current fuel tank level. DTE cannot be reset thr ough the FUNCTION SELECT button. NOTE: Significant changes in driving style or vehicle loading will greatly af fect the actual drivable distance of the vehicle, regar dless of the DTE displayed value.
Compass Display The compass readings indicate the dir ection the vehicle is facing. Press and r elease the compass button to display one of eight com- pass readings and the outside temperatur e. Automatic Compass Calibration This compass is self-calibrating, which eliminates the need to set the compass manually .
1. T urn the ignition switch ON. 2. Press and hold the compass button for appr oximately 2 seconds. 3. Press the SCROLL button until “Compass V ariance” message and the last variance zone number displays in the EVIC. 4. Press and r elease FUNCTION SELECT button until the proper variance zone is selected accor ding to the map.
• Call status: Incoming call, connecting, connected, air time in minutes and seconds, call ended, call failed, roaming, and no phone connection. • UConnect Active.
The EVIC displays this symbol to indicate the battery strength of the UConnect™ phone. The EVIC displays this symbol to indicate that a phone connection has been made. The EVIC displays this symbol to indicate that the UConnect™ phone is currently not avail- able.
Press and r elease the MENU button until Personal Set- tings displays in the EVIC. Use the SCROLL button to display one of the following choices: “Language” When in this display you may select one of five lan- guages for all display nomenclature, including the trip functions and the navigation system (if equipped).
on lock/unlock feature. T o make your selection, press and release the FUNCTION SELECT button until “ON” or “OFF” appears. “Flash Lights with Remote Key Lock” When ON is selected, the front and r ear turn signals will flash when the doors are locked or unlocked with the remote keyless entry transmitter .
door will cancel this feature. T o make your selection, press and r elease the FUNCTION SELECT button until “Off,” “45 sec.,” “5 min.,” “10 min.,” “30 min.,” or “60 min.” appears. “Confirmation of V oice Commands” — If Equipped When ON is selected, all voice commands from the UConnect™ system are confirmed.
Electrical Disturbances Radio waves may pick up electrical disturbances during transmission. They mainly affect the wave amplitude, and thus remain a part of the AM reception. They interfere very little with the fr equency variations that carry the FM signal.
SALES CODE REF — AM/FM/CD (SINGLE DISC) RADIO WITH OPTIONAL SA TELLITE RADIO AND HANDS FREE PHONE CAP ABILITY NOTE: The radio sales code is located on the lower right side of your radio faceplate. Operating Instructions - Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio.
SEEK Button (Radio Mode) Press and r elease the SEEK button to search for the next listenable station in either AM/FM or Satellite (if equipped) mode. Press the right side of the button to seek up and the left side to seek down. The radio will remain tuned to the new station until you make another selec- tion.
4. Adjust the minutes using the right side T une/Audio control. 5. T o exit, press any button/knob or wait 5 seconds. R W/FF (Radio Mode) Pressing the r ewind/fast forward button causes the tuner to search for the next fr equency in the direction of the arrows.
selected within 5 seconds after pressing the SET button, the station will continue to play but will not be stored into push-button memory . Y ou may add a second station to each push-button by repeating the above pr ocedure with this exception: Press the SET button twice and SET 2 will show in the display window .
SEEK Button (CD Mode) Press the right side of the SEEK button for the next track on the CD. Press the left side of the button to r eturn to the beginning of the current track, or r eturn to the beginning of the previous track if the CD is within the first 10 seconds of the current selection.
Press the RND button a second time to stop Random Play . Operation Instructions - Auxiliary Mode The auxiliary (AUX) jack is an audio input jack, which allows the user to plug in a portable device suc.
Mode Button (Auxiliary Mode) Press the mode button r epeatedly to select between the CD player and Satellite Radio (if equipped). Operating Instructions - Hands Free Phone — If Equipped Refer to the “HANDS FREE PHONE (UConnect™)” section of the Owner’s Manual.
Operating Instructions - Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio. Power Switch/V olume Control (Rotary) Press the ON/VOL control to turn the radio ON. Pr ess the ON/VOL a second time to turn OFF the radio.
3. After the hours are adjusted, pr ess the right side T une/Audio control to set the minutes. The minutes will begin to blink. 4. Adjust the minutes using the right side T une/Audio control. 5. T o exit, press any button/knob or wait 5 seconds. INFO Button (Radio Mode) Press the INFO button for an RBDS station (one with call letters displayed).
Press the r otary TUNE control again to exit setting tone, balance, and fade. RND/PTY Button (Radio Mode) Pressing this button once will turn on the PTY mode for 5 seconds. If no action is taken during the 5-second time out, the PTY icon will turn of f.
station with the same selected PTY name. The PTY function only operates when in the FM mode. If a preset button is activated while in the PTY (Program T ype) mode, the PTY mode will be exited and the radio will tune to the preset station.
T ape Eject Press this button and the cassette will disen- gage and eject from the radio. Scan Button Press this button to play 10 seconds of each selection. Press the scan button a second time to cancel the featur e. Changing T ape Direction If you wish to change the direction of tape travel (side being played), press Pr eset 6.
Inserting Compact Disc(s) CAUTION! This CD player will accept 4 3/4 inch (12 cm) discs only . The use of other sized discs may damage the CD player mechanism. Y ou may eject a disc with the radio OFF . If you insert a disc with the ignition ON and the radio ON, the unit will switch from radio to CD mode and begin to play when you insert the disc.
Radio display will show ⬙ EJECTING DISC ⬙ when the disc is being ejected and prompt the user to r emove the disc. Press and hold the LOAD/EJT button for 5 seconds and all CDs will be ejected from the radio. If you have ejected a disc and have not removed it within 15 seconds, it will be reloaded.
Press and hold the FF button to fast forwar d through the tracks. Release the FF button to stop the fast forward feature. If the R W button is pressed, the current track will reverse to the beginning of the track and begin playing. Press the RND button a second time to stop Random Play .
Supported MP3 File Formats The radio will recognize only files with the *.mp3 exten- sion as MP3 files. Non-MP3 files named with the *.mp3 extension may cause playback problems. The radio is designed to recognize the file as an invalid MP3 and will not play the file.
T o increase the speed of disc loading, it is r ecommended to use CD-R media and single-session discs. T o create a single-session disc, enable the Disc at Once option before writing to the disc.
INFO Button (CD Mode for MP3 Play) Press and INFO button while playing MP3 or WMA disc. The radio scrolls thr ough the following T AG information: Song T itle, Artist, File Name, and Folder Name (if avail- able). Press the INFO button once mor e to return to ⬙ elapsed time ⬙ priority mode.
Operating Instructions - V ideo Entertainment System (VES) (If Equipped) Refer to separate “V ideo Entertainment System (VES) Guide.” SALES CODE REC — AM/FM/CD (6–DISC) RADIO WITH NA VIGA TION.
1. At the Main Menu screen, highlight “Clock Setup” and press ENTER OR pr ess and hold for 3 seconds the TIME button on the unit’s faceplate. The Clock Setup screen appears. 2. T o show the GPS clock, select “Displayed Clock: GPS Clock” and press ENTER.
1. At the Clock Setup screen highlight “Displayed Clock: User Defined Clock”. 2. T o increase the clock by hours, make sure “HR +” is highlighted and press ENTER. Pr ess ENTER again to increase the clock by another hour . Y ou will see on the “User Defined T ime” display the number of hours you have increased the clock by .
Audio Clock Display Select this option to change the size of the clock on the audio screens. 1. When you are at an audio scr een, quickly press the TIME button on the navigation faceplate. 2. In this example the large clock appears on the scr een. 3. T o switch the clock to the small clock, quickly press TIME again.
VIDEO ENTERT AINMENT SYSTEM (SALES CODE XRV) — IF EQUIPPED The optional VES™ (V ideo Entertainment System) con- sists of a DVD player and LCD (liquid crystal display) screen, a battery-power ed remote control, and two head- sets. The system is located in the center console storage bin under the armrest lid.
SA TELLITE RADIO — IF EQUIPPED Satellite radio uses direct satellite to r eceiver broadcast- ing technology to provide clear digital sound, coast to coast.
simultaneously for 3 seconds. The first four digits of the twelve-digit ESN/SID number will display . Press the SEEK UP button to display the next four digits. Continue to press the SEEK UP button until all twelve ESN/SID digits display . The SEEK DOWN will page down until the first four digits display .
Selecting a Channel Press and r elease the SEEK or TUNE knob to search for the next channel. Press the top of the button to sear ch up and the bottom of the button to search down. Holding the TUNE button causes the radio to bypass channels until the button is released.
PTY Button ⴖ SEEK ⴖ When the desired pr ogram is obtained, press the ⬙ SEEK ⬙ button within five seconds. The channel will change to the next channel that matches the program type selected. Satellite Antenna T o ensure optimum r eception, do not place items on the roof ar ound the rooftop antenna location.
Center (EVIC). The EVIC features a driver -interactive display . This is located in the instrument cluster below the speedometer . The VOLUME button controls the sound level of the sound system. Press the top of the VOLUME button to increase the sound level.
T ape Player Operation Press the top of the SCROLL button once to listen to the next track on the cassette. Press the bottom of the SCROLL button once either to listen to the beginning of the current track or to listen to the beginning of the previous track if it is within 5 seconds after the curr ent track begins to play .
5. A loose tape should be corrected before use. T o rewind a loose tape, insert the eraser end of a pencil into the tape drive gear and twist the pencil in the requir ed directions. Maintain your cassette tape player . The head and capstan shaft in the cassette player can pick up dirt or tape deposits each time a cassette is played.
RADIO OPERA TION AND CELLULAR PHONES Under certain conditions, the cellular phone being On in your vehicle can cause erratic or noisy performance from your radio. This condition may be lessened or eliminated by relocating the cellular phone antenna. This condition is not harmful to the radio.
T emperature Control The rotary knob in the center contr ols air temperature. Rotate the contr ol to the left for cooler air temperature and to the right for warmer air tempera- ture. Rotating the contr ol to the ex- treme left pr ovides the coldest setting.
• Panel Air flows through the outlets located in the instrument panel. Air flows through the r egis- ters in the back of the center console to the rear seat passengers. These registers can be closed to block airflow . • Recirculation Contr ol The mode control knob also contr ols the recir culation feature.
the controls on the climate contr ol, from a dual sun- sensor located in the top of the instrument panel, fr om an infrared sensor located in the face of the climate contr ol, and from various sensors located thr oughout the vehicle. The controls on the climate contr ol provide the system with operator input.
The system will automatically control r ecir- culation. However , pressing the Recir cula- tion Control button will temporarily put the system in recir culation mode (ten minutes). This can be used when outside conditions such as smoke, odors, dust, or high humidity are pr esent.
196 UNDERST ANDING YOUR INSTRUMENT P ANEL.
The operator can override the AUTO mode setting to change airflow distribution by rotating the Mode Contr ol knob (on the right) to one of the following positions. • Defrost Air is directed to the windshield thr ough the outlets at the base of the windshield.
NOTE: T o control the air conditioning manually , the mode selector must be moved out of the AUTO position. • Recirculation Contr ol This button can be used to block out smoke, odors, dust, high humidity , or if rapid cooling is desired. The r ecirculation mode should only be used temporarily .
system lubrication to minimize the possibility of com- pressor damage when the system is started again. W indow Fogging Interior fogging on the windshield can be quickly re- moved by turning the mode selector to Defrost. The Defrost/Floor mode can be used to maintain a clear windshield and provide suf ficient heating.
Control Setting Suggestions for V arious W eather Conditions 200 UNDERST ANDING YOUR INSTRUMENT P ANEL.
REAR WINDOW FEA TURES Rear Wiper Operation The rear wiper is operated by the r ear wiper/ washer switch. The switch is located near the top center of the instrument panel. An indicator in the switch illuminates when the rear wiper is on. T o use the rear wiper , push the left side of the rear wiper/washer switch in and release.
Adding W asher Fluid The windshield washer and rear window washer shar e the same fluid reservoir . The reservoir is located in the front of the engine compartment on the passenger side of the vehicle. Be sure to check the fluid level at r egular intervals.
CAUTION! T o avoid damaging the electrical conductors of the rear window defroster , do not use scrapers, sharp instruments, or abrasive window cleaners on the interior surface of the window .
.
ST ARTING AND OPERA TING CONTENTS 䡵 Starting Procedur es .................... 2 0 8 ▫ Automatic T ransmission ................ 2 0 9 ▫ Normal Starting ...................... 2 0 9 ▫ Extremely Cold W eather (Below ⫺ 20°F Or ⫺ 29°C) ......
䡵 Power Steering ........................ 2 2 9 䡵 Multi Displacement System (MDS) - 5.7L Engine Only .......................... 2 3 0 䡵 T raction Control System (TCS) — If Equipped ............................ 2 3 0 䡵 Brake Assist System (BAS) — If Equipped .
▫ Premium System — If Equipped .......... 2 5 8 ▫ General Information ................... 2 6 1 䡵 Fuel Requirements ..................... 2 6 1 ▫ 2.7L Engine ......................... 2 6 1 ▫ 3.5L And 5.7L Engines .................. 2 6 1 ▫ Reformulated Gasoline .
ST ARTING PROCEDURES Before starting your vehicle, adjust your seat, adjust the inside and outside mirrors, fasten your seat belt, and if present, instr uct all other occupants to buckle their seat belts. W ARNING! • Never leave children alone in a vehicle.
Automatic T ransmission The gear selector must be in the NEUTRAL or P ARK position before you can start the engine. Apply the brakes before shifting into any driving gear . Normal Starting Normal Starting of either a cold or a warm engine is obtained without pumping or depressing the accelerator pedal.
W ARNING! • Never pour fuel or other flammable liquid into the throttle body air inlet opening in an attempt to start the vehicle. This could result in flash fire causing serious personal injury . • Do not attempt to push or tow your vehicle to get it started.
ENGINE BLOCK HEA TER — IF EQUIPPED The engine block heater warms engine coolant and permits quicker starts in cold weather . Connect the cord to a standard 1 10-1 15 volt AC electrical outlet with a grounded, thr ee-wire extension cor d. The engine block heater cord is r outed under the hood on the driver side of the vehicle.
W ARNING! It is dangerous to shift the selector lever out of “P” or “N” if the engine speed is higher than idle speed. If your foot is not firmly on the brake pedal, the vehicle could accelerate quickly forward or in re- verse. Y ou could lose control of the vehicle and hit someone or something.
The selector lever is automatically locked while in the P (Park) position. T o move the selector lever out of the P (Park) position, the brake pedal must be firmly depressed before the shift lock will r elease. Shift the selector lever to the desired position only when the engine is idling normally and the brake pedal is applied.
For electrical system malfunctions, there is an override for the interlock system. In order to override this system the key must be in the ignition with the switch in the ACC or ON positions. Remove the rubber storage tray from the bin located to the right of the selector lever .
Gear Ranges P (Park) P (Park) supplements the parking brake by locking the transmission. The engine can be started in this range. Never use P (Park) while the vehicle is in motion.
R (Reverse) For moving the vehicle rearwar d. Always stop before moving the lever to R (Reverse), except when rocking the vehicle. N (Neutral) Engine may be started in this range. CAUTION! Coasting the vehicle, or driving for any other reason with selector lever in NEUTRAL can result in trans- mission damage.
3 (Third) This range eliminates shifts into Overdrive. The trans- mission will operate normally in First, Second and Third while in this range. The “3” position should also be used when descending steep grades to prevent brake system distress.
clutch is not engaged, it may seem as if the transmis- sion is not shifting into “Overdrive” when cold. This is considered a normal condition. Pulling the selector lever into the “3” position will show that the transmis- sion is able to shift into and out of “Overdrive.
5 Speed Automatic T ransmission Shifting from D (Drive) to P (Park) or R (Reverse) (or from P or R to D) should be done only after the accelerator pedal is released and the vehicle is stopped. Be sure to keep your foot on the brake when moving the selector lever between these gears.
The following indicators should be used to ensure that you have engaged the selector lever into the P (Park) position: • When shifting into P (Park) move the lever all the way forward until it stops, and is fully seated. • Look at the shift indicator display on the instrument panel to ensure it is in the P (Park) position.
D (Drive) This range should be used for most city and highway driving. It provides the smoothest upshifts and down- shifts and best fuel economy . The transmission automatically upshifts through fifth gear . The D (Drive) position provides optimum driving characteristics under all normal operating conditions.
Delayed Shifts in Cold T emperatures During cold temperature operation, you may notice delayed upshifts depending on engine and transmission temperature as well as vehicle speed. This featur e im- proves warm up time of the engine and transmission to achieve maximum efficiency .
times. Follow the reset pr ocedure described under “T em- porary T ransmission Limp Home Mode” in this section. In Permanent Limp Home Mode, P (Park), R (Reverse), and N (Neutral) will continue to operate. Second gear will operate in the D (Drive) shifter position.
CAUTION! All wheels must have the same size and type tires. Unequal tire sizes must not be used. Unequal tire size may cause failure of the front differential and/or the transfer case.
P ARKING BRAKE The parking brake should always be applied when the driver is not in the vehicle. W ARNING! Never use Park position on an automatic transmis- sion as a substitute for the parking brake. Always apply parking brake fully when parked to guard against vehicle movement and possible injury or damage.
NOTE: This light only shows that the parking brake is applied. It does not show the degree of brake application. W ARNING! • Never leave children alone in a vehicle. Leaving children in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured.
The electronic brake for ce distribution (EBD) prevents the rear wheels fr om over-braking and pr ovides greater control of available braking for ces applied to the rear axle. When the vehicle is driven over 7 mph (1 1 km/h), you may also hear a slight clicking sound as well as some related motor noises.
W ARNING! • The Anti-Lock Brake System contains sophisticated electronic equipment that may be susceptible to inter- ference caused by improperly installed or high output radio transmitting equipment. This interference can cause possible loss of anti-lock braking capability .
Brake Force Distribution (EBD) systems ar e not function- ing. Immediate repair to the ABS system is requir ed. POWER STEERING The standard power steering system will give you good vehicle response and incr eased ease of maneuverability in tight spaces.
MUL TI DISPLACEMENT SYSTEM (MDS) - 5.7L Engine Only This feature of fers improved fuel economy by shutting off four of the engine’s eight cylinders during light load and cruise conditions. The system is automatic with no driver inputs or additional driving skills requir ed.
acceleration, ease up on the accelerator and apply as little throttle as possible. Be sur e to adapt your speed and driving to the prevailing r oad conditions. The TCS OFF button is located in the center of the instrument panel. T o turn OFF the TCS, momentarily press the button and the TCS Indicator Light will illumi- nate.
BRAKE ASSIST SYSTEM (BAS) — IF EQUIPPED W ARNING! The BAS (Brake Assist System) cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevail- ing road conditions.
ELECTRONIC ST ABILITY PROGRAM (ESP) — IF EQUIPPED W ARNING! The ESP (Electronic Stability Program) cannot pre- vent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevailing road conditions.
The ESP OFF button is located in the center of the instrument panel. T o turn OFF the ESP , momentarily press the ESP OFF button and the ESP/TCS Indicator Light will illuminate. T o turn the system ON again, momentarily press the ESP OFF button and the indicator light will turn OFF .
CAUTION! If the vehicle is towed with the front axle raised, the engine must be shut off (key in the ignition switch to the OFF/LOCK or ACC position). Otherwise, the ESP will immediately be engaged and will apply the rear wheel brakes. Synchronizing ESP The malfunction indicator light for the ESP is combined with BAS indicator .
TIRE SAFETY INFORMA TION Tire Markings NOTE: • P (Passenger)-Metric tir e sizing is based on U.S. design standards. P-Metric tir es have the letter “P” molded into the sidewall preceding the size designation. Ex- ample: P215/65R15 95H. • European Metric tir e sizing is based on European design standards.
T ire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standar ds ⴖ ....blank.... ⴖ = Passenger car tire based on Eur opean design standards LT = Light T ruck tire based on U.
EXAMPLE: Service Description: 95 = Load Index —A numerical code associated with the maximum load a tire can carry . H = Speed Symbol —A symbol indicating the range of speeds at which a tire can carry a load corr esponding to its load index under certain operating conditions.
Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire; however , the date code may only be on one side. T ires with white sidewalls will have the full TIN including date code located on the white sidewall side of the tire.
Tire Loading and T ire Pressure T ire Placard Location NOTE: The proper cold tir e inflation pressure is listed on either the face of the driver’s door or the driver’s side “B” pillar .
Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. Y ou will not exceed the tire’s load carrying capacity if you adhere to the loadi.
manual to determine how this reduces the available cargo and luggage load capacity of your vehicle. NOTE: The following table shows examples on how to calculate total load, cargo/luggage, and towing capaci- ties of your vehicle with varying seating configurations and number and size of occupants.
ST ARTING AND OPERA TING 243 5.
W ARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle.
2. Economy— Improper inflation pr essures can cause uneven wear patterns to develop across the tir e tread. These abnormal wear patterns will reduce tr ead life resulting in a need for earlier tire r eplacement. Under inflation, also increases tire r olling resistance and r esults in higher fuel consump- tion.
CAUTION! After inspecting or adjusting the tire pressure, al- ways reinstall the valve stem cap (if equipped). This will prevent moisture and dirt from entering the valve stem, which could damage the valve stem. Inflation pressur es specified on the placard ar e always “cold tire inflation pr essure.
W ARNING! High speed driving with your vehicle under maxi- mum load is dangerous. The added strain on your tires could cause them to fail. Y ou could have a serious accident. Don’t drive a vehicle loaded to the maximum capacity at continuous speeds above 75 mph (120 km/h).
Do not install a wheel cover or attempt to mount a conventional tire on the compact spar e wheel, since the wheel is designed specifically for the compact spare.
W ARNING! Fast spinning tires can be dangerous. Forces gener- ated by excessive wheel speeds may cause tire dam- age or failure. A tire could explode and injure someone.
Life of Tire The service life of a tire is dependent upon varying factors including but not limited to: • Driving style • T ire pressur e • Distance driven W ARNING! T ires and spare tire should be replaced after six years, regardless of the remaining tread.
W ARNING! • Do not use a tire, wheel size or rating other than that specified for your vehicle. Some combina- tions of unapproved tires and wheels may change suspension dimensions and performance charac- teristics, resulting in changes to steering, han- dling, and braking of your vehicle.
SELF–SEALING TIRES — IF EQUIPPED A non-hardening viscous sealant applied to the inner liner of each tire fills punctur es up to 0.19 in. (5 mm) to minimize the loss of air pressur e. This contributes to the safety of the vehicle by significantly reducing the pr ob- ability of a roadside stop due to a flat tir e.
NOTE: In order to avoid damage to tir es, chains, and your vehicle do not drive for a prolonged period of time on dry pavement. Observe the tire chain manufactur er’s instructions on method of installation, operating speed, and conditions for usage.
is permissible if desired. Also, correct for anything caus- ing rapid or unusual wear prior to performing the tire rotation. The suggested rotation method is the “forwar d-cross” shown in the following diagram.
• The TPM System will warn the driver of a low tire pressur e if the tire pressur e falls below the low- pressur e warning limit for any reason, including low temperature ef fects.
CAUTION! • The TPMS has been optimized for the original equipment tires and wheels. TPMS pressures and warning have been established for the tire size equipped on your vehicle. Undesirable system operation or sensor damage may result when using replacement equipment that is not of the same size, type, and/or style.
monitor tire pr essure levels. Sensors, mounted to each wheel as part of the valve stem, transmit tire pr essure readings to the Receiver Module. NOTE: It is particularly important for you to check the tire pr essure in all of the tires on your vehicle r egularly and to maintain the proper pr essure.
T elltale Light will remain ON and a chime will still sound each ignition key cycle. Once you repair or r eplace the original road tir e, and reinstall it on the vehicle in place of the compact spare,.
recommended cold placar d pressur e value. Once the system receives the updated tir e pressur es, the system will automatically update, the graphic display in the EVIC will stop flashing, and the T ire Pressur e Monitoring T elltale Light will turn off.
NOTE: Y ou can change the pressur e units to display in PSI, kP A, or BAR. Refer to “Language,” under “Personal Settings (Customer Programmable Featur es),” under “Electronic V ehicle Information Center (EVIC)” in Sec- tion 4 of this manual for details.
General Information This device complies with part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following conditions: • This device may not cause harmful interference. • This device must accept any interference r eceived, including interference that may cause undesir ed op- eration.
Light spark knock at low engine speeds is not harmful to your engine. However , continued heavy spark knock at high speeds can cause damage and immediate service is requir ed. Poor quality gasoline can cause problems such as har d starting, stalling, and hesitations.
Problems that r esult from using methanol/gasoline or E85 Ethanol blends are not the r esponsibility of the manufacturer . While MTBE is an oxygenate made from Methanol, it does not have the negative effects of Metha- nol.
malfunctioning and may requir e immediate service. Contact your dealer for service assistance. • The use of fuel additives, which are now being sold as octane enhancers, are not r ecommended. Most of these products contain high concentrations of methanol.
ADDING FUEL Fuel Filler Cap (Gas Cap) The gas cap is located behind the fuel filler door on the left side of the vehicle. Push in on the left side (near the edge) of the fuel filler door to access the fuel filler cap. If the gas cap is lost or damaged, be sure the r eplacement cap is for use with this vehicle.
CAUTION! • Damage to the fuel system or emission control system could result from using an improper fuel tank filler tube cap (gas cap). • A poorly fitting gas cap could let impurities into the fuel system. • A poorly fitting gas cap may cause the Malfunc- tion Indicator Light to turn on.
Loose Fuel Filler Cap Message If the vehicle diagnostic system determines that the fuel filler cap is loose, improperly installed, or damaged, a “Check Gascap” message will display in the Electronic V ehicle Information Center (EVIC) — if equipped.
• Month Day and Hour of Manufacture (MDH) The bar code allows a computer scanner to read the V ehicle Identification Number (VIN). Gross V ehicle Weight Rating (GVWR) The GVWR is the total allowable weight of your vehicle. This includes driver , passengers, and cargo.
driving. If weighing the loaded vehicle shows that you have exceeded either GA WR, but the total load is within the specified GVWR, you must redistribute the weight. Improper weight distribution can have an adverse ef fect on the way your vehicle steers and handles and the way the brakes operate.
TRAILER TOWING In this section, you will find safety tips and information on limits to the type of towing you can reasonably do with your vehicle. Before towing a trailer , carefully review this information to tow your load as ef ficiently and safely as possible.
T ongue W eight (TW) T ongue weight (TW) is the downward for ce exerted on the hitch ball by the trailer . In most cases it should not be less than 10% or more than 15% of the trailer load. Y ou must consider this as part of the load on your vehicle. Frontal Area Frontal ar ea is the maximum height and maximum width of the front of a trailer .
W ARNING! • An improperly adjusted W eight Distributing Hitch system may reduce handling, stability , braking performance, and could result in an acci- dent.
T railer Hitch Classification Y our vehicle may be factory equipped for safe towing of trailers weighing over 2,000 lbs (907 kg) with the optional T railer T ow Prep Package.
Engine/T ransmission Frontal Area Max. GTW (Gross T railer Wt.) Max. T ongue Wt. 2.7L Automatic 22 SQ. FT . (2.04 square meters) Up to 2 persons & Lug- gage 1,000 lbs (454 kg) 100 lbs (45 kg) 22 SQ. FT . (2.04 square meters) Up to 3 persons & Lug- gage 1,000 lbs (454 kg) 100 lbs (45 kg) 22 SQ.
Engine/T ransmission Frontal Area Max. GTW (Gross T railer Wt.) Max. T ongue Wt. 5.7L Automatic with trailer tow package 40 SQ. FT . (3.72 square meters) Up to 2 persons & Lug- gage 3,800 lbs (1724 kg) 380 lbs (172 kg) 40 SQ. FT . (3.72 square meters) Up to 3 persons & Lug- gage 3,000 lbs (1361 kg) 300 lbs (136 kg) 40 SQ.
Never exceed the maximum tongue weight stamped on your bumper or trailer hitch. Consider the following items when computing the weight on the rear axle of the vehicle: • The tongue weight of the trailer . • The weight of any other type of cargo or equipment put in or on your vehicle.
Perform the maintenance listed in Section 8 of this manual. When towing a trailer , never exceed the GA WR, or GCWR, ratings. W ARNING! Improper towing can lead to an injury accident. Follow these guidelines to make your trailer towing as safe as possible: Make certain that the load is secured in the trailer and will not shift during travel.
T owing Requirements — T ires − Do not attempt to tow a trailer while using a compact spare tir e. − Proper tir e inflation pressur es are essential to the safe and satisfactory operation of your vehicle.
W ARNING! Do not connect trailer brakes to your vehicle’s hy- draulic brake lines. It can overload your brake sys- tem and cause it to fail. Y ou might not have brakes when you need them and could have an accident. T owing any trailer will increase your stopping dis- tance.
T owing Tips Before setting out on a trip, practice turning, stopping, and backing the trailer in an area located away fr om heavy traffic. T owing T ips — Automatic T ransmission The “D” range can be selected when towing. However , if frequent shifting occurs while in this range, the “3” range should be selected.
T owing T ips — Electronic Speed Control (If Equipped) − Don’t use in hilly terrain or with heavy loads. − When using the speed control, if you experience speed drops gr eater than 10 mph (16 km/h), disengage until you can get back to cruising speed.
RECREA TIONAL TOWING (BEHIND MOTORHOME, ETC.) TOWING THIS VEHICLE BEHIND ANOTHER VEHICLE (Flat towing with all four wheels on the ground) Recreational towing for this vehicle is not r ecommended. NOTE: If the vehicle requir es towing, make sure all four wheels are of f the ground.
WHA T T O DO IN EMERGENCIES CONTENTS 䡵 Hazard W arning Flasher ................. 2 8 4 䡵 If Y our Engine Overheats ................ 2 8 4 䡵 Jacking And T ire Changing ............... 2 8 6 ▫ Preparations For Jacking ................ 2 8 6 ▫ Jack Location/Spare T ire Stowage .
HAZARD W ARNING FLASHER The hazard flasher switch is located in the center of the instrument panel below the center air outlets. T o engage the Hazard W arning Flashers, depress the switch on the instrument panel.
control to maximum heat, the Mode contr ol to floor , and the fan control to HI. This allows the heater cor e to act as a supplement to the radiator and aids in removing heat from the engine cooling system. CAUTION! Driving with a hot cooling system could damage your vehicle.
JACKING AND TIRE CHANGING W ARNING! • Do not attempt to change a tire on the side of the vehicle close to moving traffic. Pull far enough of f the road to avoid the danger of being hit when operating the jack or changing the wheel. • Getting under a jacked-up vehicle is dangerous.
5. Passengers should not remain in the vehicle when the vehicle is being jacked. 6. Block both the front and r ear of the wheel diagonally opposite the jacking position.
3. Lift the access cover using the pull strap. 4. Remove the fastener securing the spare tir e. Lifting The Access Cover Spare T ire Fastener 288 WHA T TO DO IN EMERGENCIES.
5. Remove the spare tir e. 6. Remove the fastener securing the jack. W ARNING! A loose tire or jack thrown forward in a collision or hard stop could endanger the occupants of the ve- hicle. Always stow the jack parts and the spare tire in the places provided.
W ARNING! T o avoid possible personal injury , handle the wheel covers with care to avoid contact with the metal edges and retention teeth. 4. Before raising the vehicle, use the lug wr ench to loosen, but not remove, the lug nuts on the wheel with the flat tire.
Jack Engagement Locations WHA T TO DO IN EMERGENCIES 291 6.
6. Raise the vehicle just enough to remove the flat tir e and install the spare tir e. W ARNING! Raising the vehicle higher than necessary can make the vehicle less stable. It could slip off the jack and hurt someone near it. Raise the vehicle only enough to remove the tire.
Wheel Cover Installation (If Required) 1. T ighten the two lug nuts on the mounting studs on each side of the stud which is in alignment with the valve stem. 2. Align the valve notch in the wheel cover with the valve stem on the wheel. 3. Install the cover by hand, snapping the cover over the two lug nuts.
JUMP-ST ARTING PROCEDURES W ARNING! • T ake care to avoid the radiator cooling fan whenever the hood is raised. It can start anytime the ignition switch is on. Y ou can be hurt by the fan. • Do not attempt to push or tow your vehicle to get it started.
3. Set the parking brake, place the automatic transmis- sion in P ARK, and turn the ignition switch to the OFF (or LOCK) position on both vehicles. 4. T urn off the heater , radio, and all unnecessary electri- cal loads. 5. Connect one end of the jumper cable to the remote jump-start positive battery post (+) in the engine com- partment.
W ARNING! • Y ou should not try to start your vehicle by push- ing or towing. • Do not connect the cable to the negative post of the discharge battery . The resulting electrical spark could cause the battery to explode. • During cold weather when temperatures are be- low freezing point, electrolyte in a discharged battery may freeze.
FREEING A STUCK VEHICLE If your vehicle becomes stuck in mud, sand, or snow , it can often be moved by a rocking motion. T urn your steering wheel right and left to clear the area ar ound the front wheels. Then shift back and forth between Reverse and Drive.
TOWING A DISABLED VEHICLE WITHOUT THE IGNITION KEY Special care must be taken when the vehicle is towed with the ignition in the LOCK position. The only ap- proved method of towing without the ignition key is with a flat bed truck. Pr oper towing equipment is neces- sary to prevent damage to the vehicle.
If you must use the accessories (wipers, defrosters, etc.) while being towed, the key must be in the ON position, not the ACCESSORY position. Make certain the transmis- sion remains in NEUTRAL. TOWING THIS VEHICLE BEHIND ANOTHER VEHICLE WITH A TOW DOLL Y The manufacture does not recommend that you tow this vehicle on a tow dolly .
.
MAINT AINING YOUR VEHICLE CONTENTS 䡵 2.7L Engine Compartment ............... 3 0 3 䡵 3.5L Engine Compartment ............... 3 0 4 䡵 5.7L Engine Compartment ............... 3 0 5 䡵 Onboard Diagnostic System — OBD II ...... 3 0 6 ▫ Loose Fuel Filler Cap .
▫ Body Lubrication ..................... 3 2 0 ▫ W iper Blades ........................ 3 2 0 ▫ W indshield W ashers/Rear W indow W asher . . . 321 ▫ Exhaust System ...................... 3 2 1 ▫ Cooling System ....................... 3 2 2 ▫ Hoses And V acuum/V apor Harnesses .
2.7L ENGINE COMP ARTMENT MAINT AINING YOUR VEHICLE 303 7.
3.5L ENGINE COMP ARTMENT 304 MAINT AINING YOUR VEHICLE.
5.7L ENGINE COMP ARTMENT MAINT AINING YOUR VEHICLE 305 7.
ONBOARD DIAGNOSTIC SYSTEM — OBD II Y our vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems.
A loose, improperly installed, or damaged fuel filler cap may also turn on the Malfunction Indicator Light (MIL). EMISSIONS INSPECTION AND MAINTENANCE PROGRAMS In some localities, it may be a legal requir ement to pass an inspection of your vehicle’s emissions control system.
b. The MIL will not flash at all and will remain fully illuminated until you turn off the ignition key or start the engine. This means that your vehicle’s OBD system is ready and you can proceed to the I/M station. If your OBD system is not ready , you should see your authorized dealer or repair facility .
W ARNING! Y ou can be badly injured working on or around a motor vehicle. Only do service work for which you have the knowledge and the proper equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent me- chanic.
CAUTION! Overfilling or underfilling will cause oil aeration or loss of oil pressure. This could damage your engine. Checking Oil Level — 5.7L Engine T o assure pr oper engine lubrication, the engine oil must be maintained at the correct level. Check the oil level at regular intervals, such as every fuel stop.
CAUTION! Overfilling or underfilling will cause oil aeration or loss of oil pressure. This could damage your engine. Change Engine Oil Road conditions and your kind of driving affect the interval at which your oil should be changed. Check the following list to see if any apply to you.
American Petroleum Institute (API) Engine Oil Identification Symbol This symbol means that the oil has been certified by the American Petroleum Institute (API). The manufacture only r ecommends API Certified engine oils. Engine Oil V iscosity (SAE Grade) — 2.
The engine oil filler cap also shows the recommended engine oil viscosity for your engine. For information on engine oil filler cap location, refer to the “Engine Com- partment” illustration in this section. In areas wher e these grades are not generally available, higher SAE grades may be used.
Engine Oil Filter The engine oil filter should be replaced at every engine oil change. Engine Oil Filter Selection This manufacturer’s engines have a full-flow type oil filter . Use a filter of this type for replacement. The quality of replacement filters varies considerably .
W ARNING! The air induction system (air cleaner , hoses, etc) can provide a measure of protection in the case of engine backfire. Do not remove the air induction system (air cleaner , hoses, etc) unless such removal is necessary for repair or maintenance.
NOTE: Intentional tampering with emissions control systems can result in civil penalties being assessed against you. W ARNING! A hot exhaust system can start a fire if you park over materials that can burn. Such materials might be grass or leaves coming into contact with your ex- haust system.
W ARNING! • Battery fluid is a corrosive acid solution and can burn or even blind you. Don’t allow battery fluid to contact your eyes, skin, or clothing. Don’t lean over a battery when attaching clamps. If acid splashes in eyes or on skin, flush the area imme- diately with large amounts of water .
CAUTION! • It is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post. Battery posts are marked posi- tive (+) and negative (-) and identified on the battery case.
Refrigerant Recovery and Recycling R-134a Air Conditioning Refrigerant is a hydrofluor ocar- bon (HFC) that is endorsed by the Environmental Pr o- tection Agency and is an ozone-saving product.
surfaces. Refer to “Fluids, Lubricants, and Genuine Parts” in this section for the correct fluid type. Front & Rear Suspension Ball Joints The suspension ball joints should be inspected for exter- nal leakage or damage when other maintenance is per- formed.
Windshield W ashers/Rear Window W asher The windshield washer and the rear window washer share the same fluid r eservoir . The fluid reservoir is located in the front of the engine compartment on the passenger side of the vehicle. Be sure to check the fluid level in the reservoir at r egular intervals.
Cooling System W ARNING! • When working near the radiator cooling fan, dis- connect the fan motor lead or turn the ignition switch to the OFF position. The fan is temperature controlled and can start at any time the ignition switch is in the ON position.
Cooling System — Drain, Flush, and Refill The system should be drained, flushed, and refilled at the intervals shown on the Maintenance Schedule. If the solution is dirty or contains a considerable amount of sediment, clean and flush with a reliable cooling system cleaner .
extended maintenance period, it is important that you use the same coolant throughout the life of your vehicle. Please review these r ecommendations for using Hybrid Organic Additive T echnology (HOA T) coolant.
W ARNING! • The warning words “DO NOT OPEN HOT” on the cooling system pressure cap are a safety pre- caution. Never add coolant when the engine is overheated. Do not loosen or remove the cap to cool an overheated engine. Heat causes pressure to build up in the cooling system.
When additional coolant is needed to maintain the proper level, it should be added to the coolant bottle. Do not overfill. Points T o Remember NOTE: When the vehicle is stopped after a few miles (kilometers) of operation, you may observe vapor coming from the fr ont of the engine compartment.
Hoses and V acuum/V apor Harnesses Inspect surfaces of hoses and nylon tubing for evidence of heat and mechanical damage. Hard or soft spots, brittle rubber , cracking, tears, cuts, abrasions, and exces- sive swelling indicate deterioration of the rubber .
W ARNING! Riding the brakes can lead to brake failure and possibly an accident. Driving with your foot resting or riding on the brake pedal can result in abnormally high brake temperatures, excessive lining wear , and possible brake damage. Y ou wouldn’t have your full braking capacity in an emergency .
W ARNING! W orn brake hoses can burst and cause brake failure. Y ou could have an accident. If you see any signs of cracking, scuffing, or worn spots, have the brake hoses replaced immediately .
CAUTION! Do not allow petroleum base fluid to contaminate the brake fluid, all brake seal components could be damaged causing partial or complete brake failure. Automatic T ransmission Fluid Level Check Regular automatic transmission fluid level checks are not requir ed.
Severe Usage (fluid and filter) — Refer to Maintenance Schedule “B” Severe Usage is defined as: • Police, taxi, limousine, commercial type operation, or trailer towing where the vehicle is driven regularly for more than 45 minutes of continuous operation.
Fluid Changes The fluid should be changed as follows: Normal Usage Front Dif ferential No Service Required T ransfer Case Refer to Maintenance Schedule “A” Severe Usage Front Dif ferential No Service Required T ransfer Case Refer to Maintenance Schedule “B” Severe Usage is defined as: 1.
What Causes Corrosion? Corrosion is the r esult of deterioration or removal of paint and protective coatings fr om your vehicle. The most common causes are: • Road salt, dirt, and moisture accumulation. • Stone and gravel impact. • Insects, tree sap, and tar .
• If you detect any stone chips or scratches in the paint, touch them up immediately . The cost of such repairs is considered the r esponsibility of the owner . • If your vehicle is damaged due to an accident or similar cause, which destroys the paint and pr otective coating, have your vehicle repair ed as soon as pos- sible.
and Mopar 威 T otal Clean or equivalent. Care should be taken to avoid soaking your leather upholstery with any liquid. Please do not use polishes, oils, cleaning fluids, solvents, detergents, or ammonia-based cleaners to clean your leather upholstery .
1. Clean with a wet soft rag or micro-fiber towel. A mild soap solution may be used, but do not use high alcohol content or abrasive cleaners. If soap is used, wipe clean with a clean damp rag. 2. Dry with a soft tissue. Seat Belt Maintenance Do not bleach, dye, or clean the belts with chemical solvents or abrasive cleaners.
FUSES (POWER DISTRIBUTION CENTERS) Fuses (Front Power Distribution Center) A power distribution center is located in the engine compartment. This center contains fuses and relays.
Cavity Car- tridge Fuse Mini Fuse Description 1 1 — 25 Amp Clear Auto Shutdown/ Powertrain Control Module (PCM) 12 — — — 13 — — — 14 — 25 Amp Clear Powertrain Control Module (PCM) 15 .
CAUTION! • When installing the Power Distribution Center cover , it is important to ensure the cover is prop- erly positioned and fully latched. Failure to do so may allow water to get into the Power Distribu- tion Center , and possibly result in a electrical system failure.
Cavity Car- tridge Fuse Mini Fuse Description 1 60 Amp Y ellow — Ignition Off Draw (IOD) 2 40 Amp Green — Battery 3— — — 4 40 Amp Green — Battery 5 30 Amp Pink — Heated Seats - if equipp.
Cavity Car- tridge Fuse Mini Fuse Description 13 * ——— 14 — 10 Amp Red AC Heater Control/ Cluster/Sentry Key Re- mote Keyless Entry 15 — 20 Amp Y ellow T railer T ow Brake Mod- ule - if equi.
Cavity Car- tridge Fuse Mini Fuse Description 33 — — — 34 — — — 35 — 5 Amp Orange Amplifier - if equipped/ Antenna/Ignition Delay/Overhead Console/Passenger Door Lock & Express Power.
* Cavities 1 1, 12, and 13 contain self-resetting fuses (circuit br eakers) that are only serviceable by an autho- rized dealer . The Cluster is fused by the 25 amp circuit breaker in Cavity 1 1. The Passenger Seat Switch is fused by the 25 amp circuit br eaker in Cavity 12.
VEHICLE STORAGE If you are leaving your vehicle dormant for mor e than 21 days, you may want to take steps to protect your battery . Y ou may: • Disconnect the negative cable from the battery . • Anytime you store your vehicle, or keep it out of service (i.
LIGHT BULBS — Exterior Bulb Number Low Beam Headlight ..................... 9006 High Beam Headlight ..................... 9005 Front Park/T urn Light ................... 3457A Front Fog Light—If Equipped . . . 9145/H10 (Serviced at Dealer) Front Sidemarker .
CAUTION! Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. If the bulb comes in contact with an oily surface, clean the bulb with rubbing alcohol. T ail/Stop, T urn Signal Light, and Backup Light 1. Open the liftgate.
3. Push the electrical connector locking tab to the side. 4. Disconnect the electrical connector . 5. Remove 1 wing nut from the back of the tail light assembly . 6. Remove 2 push pin fasteners under the liftgate with a flat blade tool. 7. Pull tail light assembly clear from vehicle to access bulbs.
9. Pull the bulb out of the socket assembly . 10. Push the replacement bulb into the socket assembly . 1 1. Reinstall the bulb and socket assembly into the tail light assembly , and then turn it clockwise. 12. Reinstall the tail light assembly , fasteners, and elec- trical connector .
License Light 1. Remove the screws securing the light to the r ear fascia. 2. Remove the bulb and socket assembly . 3. Pull the bulb out of the socket assembly . 4. Push the replacement bulb into the socket assembly . 5. Reinstall the bulb and socket assembly .
FLUIDS AND CAP ACITIES U.S. Metric Fuel (approximate) 2.7 Liter Engine 18 gallons 68 liters 3.5 Liter Engine without All Wheel Drive 18 gallons 68 liters 3.5 Liter Engine with All Wheel Drive 19 gallons 72 liters 5.7 Liter Engine 19 gallons 72 liters Engine Oil-W ith Filter 2.
FLUIDS, LUBRICANTS, AND GENUINE P ARTS Engine Component Fluids, Lubricants, and Genuine Parts Engine Coolant Mopar 威 Antifreeze/Coolant 5 Y ear/100,000 Mile Formula HOA T (Hybrid Or- ganic Additive T echnology) or equivalent Engine Oil (2.7 Liter) Use API Certified engine oil.
Chassis Component Fluids, Lubricants, and Genuine Parts Automatic T ransmission Mopar 威 A TF+4 Automatic T ransmission Fluid. Brake Master Cylinder Mopar 威 DOT 3, SAE J1703 should be used. If DOT 3, SAE J1703 brake fluid is not available, then DOT 4 is acceptable.
MAINTENANCE SCHEDULES CONTENTS 䡵 Emission Control System Maintenance ...... 3 5 4 䡵 Maintenance Schedules .................. 3 5 4 ▫ Schedule “B” .
EMISSION CONTROL SYSTEM MAINTENANCE The “Scheduled” maintenance services, listed in bold type must be done at the times or mileages specified to assure the continued pr oper functioning of the emission control system.
• Extensive engine idling. • Driving in dusty conditions. • Short trips of less than 10 miles (16 km). • More than 50% of your driving is at sustained high speeds during hot weather , above 90°F (32°C). • T railer towing. 〫 • T axi, police, or delivery service (commercial ser - vice).
the vehicle is on level ground will impr ove the accu- racy of the oil level reading. Add oil only when the level is at or below the ADD or MIN mark. • Check the windshield washer solvent and add if requir ed. Once a Month • Check tire pr essure and look for unusual wear or damage.
SCHEDULE “B” Follow Schedule “B” if you usually operate your vehicle under one or more of the following conditions. Change the automatic transmission fluid and filter every 60,000 miles (100 000 km) if the vehicle is usually operated under one or more of the conditions marked with an 〫 .
Miles 3,000 6,000 9,000 12,000 15,000 18,000 (Kilometers) (5 000) (10 000) (15 000) (20 000) (25 000) (30 000) Change engine oil and engine oil filter , if not replaced at 3 months. XXXXX X Inspect the air cleaner filter and replace if r e- quired.* XXXX X Replace the air cleaner filter .
Miles 21,000 24,000 27,000 30,000 33,000 36,000 (Kilometers) (35 000) (40 000) (45 000) (50 000) (55 000) (60 000) Change engine oil and engine oil filter , if not replaced at 3 months. XXXXX X Inspect the air cleaner filter and replace if r e- quired.
Miles 39,000 42,000 45,000 48,000 51,000 54,000 (Kilometers) (65 000) (70 000) (75 000) (80 000) (85 000) (90 000) Change engine oil and engine oil filter , if not replaced at 3 months. XXXXX X Inspect the air cleaner filter and replace if r e- quired.
Miles 57,000 60,000 63,000 66,000 69,000 72,000 (Kilometers) (95 000) (100 000) (105 000) (1 10 000) (1 15 000) (120 000) Change engine oil and engine oil filter , if not replaced at 3 months. XXXXX X Inspect the air cleaner filter and replace if r e- quired.
Miles 75,000 78,000 81,000 84,000 87,000 90,000 (Kilometers) (125 000) (130 000) (135 000) (140 000) (145 000) (150 000) Change engine oil and engine oil filter , if not replaced at 3 months. XXXXX X Inspect the air cleaner filter and replace if r e- quired.
Miles 93,000 96,000 99,000 102,000 105,000 (Kilometers) (155 000) (160 000) (165 000) (170 000) (175 000) Change engine oil and engine oil filter , if not re- placed at 3 months. XXXXX Inspect the air cleaner filter and replace if r e- quired.* XXXX Replace the air cleaner filter .
Miles 108,000 11 1,000 1 14,000 1 17,000 120,000 (Kilometers) (180 000) (185 000) (190 000) (195 000) (200 000) Change engine oil and engine oil filter , if not re- placed at 3 months. XXXXX Inspect the air cleaner filter and replace if r e- quired.* XXXX Replace the air cleaner filter .
Miles 123,000 126,000 129,000 132,000 135,000 (Kilometers) (205 000) (210 000) (215 000) (220 000) (225 000) Change engine oil and engine oil filter , if not re- placed at 3 months. XXXXX Inspect the air cleaner filter and replace if r e- quired.* XXXX Replace the air cleaner filter .
Miles 138,000 141,000 144,000 147,000 150,000 (Kilometers) (230 000) (235 000) (240 000) (245 000) (250 000) Change engine oil and engine oil filter , if not re- placed at 3 months. XXXXX Inspect the air cleaner filter and replace if r e- quired.* XXXX Replace the air cleaner filter .
SCHEDULE “A” Miles 6,000 12,000 18,000 24,000 30,000 36,000 (Kilometers) (10 000) (20 000) (30 000) (40 000) (50 000) (60 000) [Months] [6] [12] [18] [24] [30] [36] Change engine oil and engine oil filter . X XXXXX Inspect the air cleaner filter and replace if r e- quired.
Miles 42,000 48,000 54,000 60,000 66,000 72,000 (Kilometers) (70 000) (80 000) (90 000) (100 000) (1 10 000) (120 000) [Months] [42] [48] [54] [60] [66] [72] Change engine oil and engine oil filter . X X X X X X Inspect the air cleaner filter and replace if requir ed.
Miles 78,000 84,000 90,000 96,000 102,000 (Kilometers) (130 000) (140 000) (150 000) (160 000) (170 000) [Months] [78] [84] [90] [96] [102] Change engine oil and engine oil filter . X X X X X Inspect the air cleaner filter and replace if r e- quired.* XX X X Replace the air cleaner filter .
Miles 108,000 1 14,000 120,000 126,000 132,000 (Kilometers) (180 000) (190 000) (200 000) (210 000) (220 000) [Months] [108] [1 14] [120] [126] [132] Change engine oil and engine oil filter . X X X X X Inspect the air cleaner filter and replace if r e- quired.
Miles 138,000 144,000 150,000 (Kilometers) (230 000) (240 000) (250 000) [Months] [138] [144] [150] Change engine oil and engine oil filter . X X X Inspect the air cleaner filter and replace if r equired.* X X Replace the air cleaner filter . X Inspect the front and r ear brake linings and rotors.
.
IF YOU NEED CONSUMER ASSIST ANCE CONTENTS 䡵 Suggestions For Obtaining Service For Y our V ehicle .............................. 3 7 4 ▫ Prepar e For The Appointment ............ 3 7 4 ▫ Prepar e A List ........................ 3 7 4 ▫ Be Reasonable W ith Requests .
SUGGESTIONS FOR OBT AINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment If you’re having warranty work done, be sur e to have the right papers with you. T ake your warranty folder . All work to be performed may not be covered by the warranty , discuss additional charges with the service manager .
• If for some reason you ar e still not satisfied, talk to the general manager or owner of the dealership. They want to know if you need assistance. • If your dealership is unable to resolve the concern, you may contact the Manufacturer’s Customer Center .
Service Contract Y ou may have purchased a service contract for your vehicle to help protect you fr om the high cost of unex- pected repairs after your manufactur er’s new vehicle limited warranty expires. The manufactur er stands be- hind only the manufacturer’s Service Contracts.
REPORTING SAFETY DEFECTS In the 50 United States and W ashington D.C.: If you believe that your vehicle has a defect, which could cause a crash or cause injury or death, you should immediately inform the National Highway T raffic Safety Administra- tion (NHTSA) in addition to notifying the manufacturer .
Corporation vehicles. A complete working knowledge of the vehicle, system, and/or components is written in straightforward language with illustrations, dia- grams, and charts.
T readwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under contr olled con- ditions on a specified government test course. For ex- ample, a tire graded 150 would wear one and a half (1 1/2) times as well on the government course as a tire graded 100.
W ARNING! The temperature grade for this tire is established for a tire that is properly inflated and not overloaded. Excessive speed, under inflation, or excessive load- ing, either separately or in combination, can cause heat buildup and possible tire failure.
INDEX 10.
ABS (Anti-Lock Brake System) ............. 2 2 6 Adding Engine Coolant (Antifreeze) ......... 3 2 3 Adding Fuel .......................... 2 6 5 Adding Rear W asher Fluid ................ 2 0 2 Adding W asher Fluid .............. 103,202,321 Adjustable Pedals .
Fluid Change ........................ 3 3 0 Fluid Level Check ..................... 3 3 0 F l u i dT y p e .......................... 3 5 2 Gear Ranges ......................... 2 1 5 Shifting .......................... 214,219 Special Additives .....
Cargo Management System ............... 1 2 2 Cargo Or ganizer ...................... 1 2 7 Rollaway T onneau Cover ............... 1 2 5 T ri-Fold Load Floor .................... 1 2 3 W aterproof Liner ..................... 1 2 7 Cargo T ie-Downs ..
C r u i s eL i g h t ........................... 1 4 0 C u pH o l d e r ........................ 121,336 Customer Assistance .................... 3 7 4 Data Recorder , Event ..................... 4 9 Daytime Running Lights .................. 9 8 Dealer Service .
Flooded, Starting ..................... 2 0 9 Fuel Requirements ................. 261,350 O i l .......................... 309,350,351 Oil Change Interval ................... 3 1 1 Oil Filler Cap ........................ 3 1 2 O i lS e l e c t i o n .
C l e a n A i r ........................... 2 6 2 Ethanol ............................. 2 6 2 Filler Cap (Gas Cap) ................... 2 6 5 Filter .............................. 3 1 5 Gasoline ............................ 2 6 1 Gauge ................
Heater , Engine Block .................... 2 1 1 High Beam/Low Beam Select (Dimmer) Switch . 99 Hitches T r a i l e rT o w i n g ....................... 2 7 3 H o l d e r ,C u p ........................... 1 2 1 HomeLink 威 (Garage Door Opener) T ransmitter .
Hood ............................... 9 5 Lead Free Gasoline ...................... 2 6 1 L i f eo fT i r e s ........................... 2 5 0 L i f t g a t e ............................... 3 1 Liftgate W indow W iper/W asher ............ 2 0 1 L i g h t s .
Load Leveling System ................... 1 3 1 Loading V ehicle ..................... 267,268 Capacities ........................... 2 6 8 T i r e s ............................... 2 4 0 Locks ................................ 2 2 A u t oU n l o c k ..
Odometer ............................ 1 4 0 T r i p ............................... 1 4 0 Oil, Engine ......................... 309,351 Capacity ............................ 3 5 0 Change Interval ...................... 3 1 1 Checking .................
Pretensioners Seat Belts ............................ 3 8 Programmable Electr onic Features ..... 1 1 1 , 1 1 4 , 1 5 6 Programming T ransmitters (Remote Keyless E n t r y ) ........................... 2 1 , 1 1 1 , 1 1 4 Radial Ply T ires ...........
Satellite Radio Antenna .................. 1 8 7 Schedule, Maintenance ................... 3 5 4 Seat Belt Maintenance ................... 3 3 6 Seat Belt Reminder ...................... 3 9 Seat Belts .............................. 3 3 Adjustable Upper Shoulder Anchorage .
S t a r t i n g .............................. 2 0 8 Automatic T ransmission ................ 2 0 9 Engine Fails to Start ................... 2 0 9 Starting and Operating ................... 2 0 8 Starting Procedur es ..................... 2 0 8 Steering Column Controls .
Jacking .......................... 286,289 L i f eo fT i r e s ......................... 2 5 0 Load Capacity .................... 240,241 Pressur e Monitor System (TPMS) ......... 2 5 4 Quality Grading ...................... 3 7 8 Radial .............
T rip Odometer ......................... 1 4 0 T urn Signals ........................ 9 9 , 1 4 2 UConnect™ (Hands-Free Phone) ............ 7 0 Uniform T ire Quality Grades .............. 3 7 8 Universal T ransmitter .................... 1 1 0 Unleaded Gasoline .
NOTES.
NOTES.
NOTES.
NOTES.
デバイスDodge 2007 LX Magnumの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Dodge 2007 LX Magnumをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはDodge 2007 LX Magnumの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Dodge 2007 LX Magnumの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Dodge 2007 LX Magnumで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Dodge 2007 LX Magnumを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はDodge 2007 LX Magnumの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Dodge 2007 LX Magnumに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちDodge 2007 LX Magnumデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
