DodgeメーカーDurango (2008)の使用説明書/サービス説明書
ページ先へ移動 of 481
T ABLE OF CONTENTS SECTION P AGE 1 INTRODUCTION .............................................................3 2 THINGS TO KNOW BEFORE ST AR TING YOUR VEHICLE ............................... 9 3 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE ...........
I n f o r m a t i o n P r o v i d e d b y :.
INTRODUCTION CONTENTS m Introduction ........................... 4 m Rollover W arning ........................ 4 m How T o Use This Manual .................. 5 m W arnings And Cautions ................... 7 m V ehicle Identification Number ..........
INTRODUCTION This manual has been prepar ed with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your new vehicle. It is supplemented by a W arranty Information Booklet and various customer oriented documents.
Failure to use driver and passenger seat belts pr ovided is a major cause of severe or fatal injury . In fact, the U.S. government notes that the universal use of existing seat belts could cut the highway death toll by 10,000 or more each year , and could reduce disabling injuries by 2 million annually .
6 INTRODUCTION I n f o r m a t i o n P r o v i d e d b y :.
W ARNINGS AND CAUTIONS This manual contains W ARNINGS against operating procedur es, which could result in an accident or bodily injury . It also contains CAUTIONS against pr ocedures, which could result in damage to your vehicle. If you do not read this entire manual, you may miss important information.
VEHICLE MODIFICA TIONS/AL TERA TIONS W ARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death.
THINGS T O KNOW BEFORE ST ARTING YOUR VEHICLE CONTENTS m A W ord About Y our Keys .................. 1 2 ▫ Ignition Key Removal ................... 1 2 ▫ Locking Doors W ith The Key .............. 1 3 m Sentry Key ............................ 1 3 ▫ Replacement Keys .
▫ General Information .................... 2 4 ▫ Programming Additional T ransmitters ........ 2 5 ▫ Battery Replacement .................... 2 6 m Remote Starting System — If Equipped ........ 2 7 m Door Locks ............................ 2 8 ▫ Manual Door Locks .
▫ Seat Belts And Pregnant W omen ............ 5 2 ▫ Seat Belt Extender ...................... 5 2 ▫ Driver And Right Front Passenger Supplemental Restraint System (SRS)—Airbags ........... 5 3 ▫ Event Data Recorder (EDR) ............... 6 2 ▫ Child Restraint .
A WORD ABOUT YOUR KEYS The dealer that sold you your new vehicle has the key code numbers for your vehicle locks. These numbers can be used to order duplicate keys from your dealer . Ask your dealer for these numbers and keep them in a safe place. Ignition Key Removal Automatic T ransmission Place the shift lever in P ARK.
in the ignition cylinder . If this occurs, rotate the key to the right slightly , then remove the key as described. If a malfunction occurs, the system will trap the key in the ignition cylinder to warn you that this safety feature is inoperable. The engine can be started and stopped but the key cannot be removed until you obtain service.
The system uses ignition keys, which have an embedded electronic chip (transponder), to prevent unauthorized vehicle operation. Therefor e, only keys that are pro- grammed to the vehicle can be used to start and operate the vehicle. The system will shut the engine off in two (2) seconds if someone uses an invalid key to start the engine.
All of the keys provided with your new vehicle have been programmed to the vehicle electronics. Replacement Keys NOTE: Only keys that are programmed to the vehicle electronics can be used to start and operate the vehicle. Once a Sentry Key is programmed to a vehicle, it cannot be programmed to any other vehicle.
3. Insert the second valid key into the ignition switch. T urn the ignition switch to the “ON” position within 15 seconds. After ten seconds, a chime will sound. In addition, the V ehicle Security Alarm Indicator Light will begin to flash. T urn the ignition switch to the “LOCK” position and remove the second key .
IGNITION AND STEERING LOCK In the LOCK position, the steering and ignition systems are locked to provide anti-theft pr otection for your ve- hicle. It may be difficult to turn the key from the LOCK position when starting your vehicle, if the steering wheel is locked.
W ARNING! The key cannot be turned to LOCK until the selector is in the P ARK position. Do not attempt to pull the shift lever out of P ARK after the key is in the LOCK position.
T o Set the Alarm: The alarm will set when you use the power door locks or use the Keyless Entry transmitter to lock the doors. After all the doors are locked and closed the security light in the instrument cluster will flash rapidly to signal that the system is arming.
UNLOCK button or by inserting a pr ogrammed Sentry Key into the ignition and turning the key to the ON position. ILLUMINA TED ENTR Y V ehicles Equipped With Power Door Locks All interior lights will illuminate in the vehicle when the doors are unlocked using the key fob.
NOTE: Y our vehicle’s keyfob may have thr ee, four or five buttons (shown), depending on the optional features purchased with your vehicle. This system allows you to lock or unlock the doors and liftgate or activate the panic alarm from distances a minimum of 66 feet (20 meters) using a hand held radio transmitter .
3. Release both buttons at the same time. 4. T est the feature while outside of the vehicle, by pressing the LOCK/UNLOCK button on the keyfob. NOTE: Pressing the LOCK button on the keyfob while you are inside the vehicle will activate the Security Alarm.
4. T o reactivate this featur e, repeat the above steps. 5. T est the horn chirp feature while outside of the ve- hicle, by pressing the LOCK button on the key fob with the ignition in the OFF position and the key removed. NOTE: Pressing the LOCK button on the keyfob, while you are inside the vehicle, will activate the Security Alarm.
Using the Panic Alarm T o activate the Panic mode while the ignition is OFF press and release the P ANIC button on the transmitter once. When the Panic mode is activated, the interior lights will illuminate, the headlamps and parking lights will flash, and the horn will sound.
Programming Additional T ransmitters V ehicles will be shipped fr om the assembly plants with two key fob transmitters programmed only for that vehicle. A total of eight fobs can be pr ogrammed for your vehicle. Additional fobs can be programmed to your vehicle through the use of a currently programmed fob.
12. Repeat steps 8 through 10 to program up to six additional fobs. 13. T urn the ignition to the OFF position. 14. Y our vehicle will remain in program mode up to 60 seconds from when the original chime was heard. After 60 seconds, all programmed fobs function normally .
with your fingers. Skin oils may cause battery deteriora- tion. If you touch a battery , clean it with rubbing alcohol. 3. T o reassemble the transmitter case, snap the two halves of the case together . Make sur e there is an even “gap” between the two halves.
T o enter the vehicle while the engine is running during a remote start, you must first unlock the vehicle using the UNLOCK button on the key fob. After the vehicle is unlocked, you have 60 seconds to.
W ARNING! • For personal security and safety in the event of an accident, lock the vehicle doors when you drive as well as when you park and leave the vehicle. • Never leave children alone in a vehicle. Leaving children in a vehicle unattended is dangerous for a number of reasons.
chime will sound if the key is in the ignition switch and a door is open, as a reminder to remove the key . Automatic Door Locks If this feature is enabled, your door locks will lock automatically when the vehicle’s speed exceeds 15 mph (24 km/h).
Auto Unlock On Exit — If Equipped This feature unlocks all of the doors of the vehicle when any door is opened (excluding the liftgate). This will occur only after the vehicle has been shifted into the Park position after the vehicle has been driven (shifted out of Park and all doors closed).
Child Protection Door Lock T o provide a safer environment for children riding in the rear seat, the rear doors of your vehicle have the child- protection door lock system. T o use the system, open each rear door and slide the control UP to engage the locks and DOWN to disengage the child-protection locks.
WINDOWS Power Windows The control on the left front door has up-down switches that give you finger tip control of all four power win- dows. Ther e is a single opening and closing switch on the passenger doors for passenger window control.
Auto Down The driver’s and front passenger window switch has an Auto Down feature. Push the window switch past the first detent, release, and the window will go down automatically . T o cancel the Auto Down movement, operate the switch in either the up or down dir ection and release the switch.
Resetting the Auto-Up Feature Should the Auto-Up feature stop working the window probably needs to be reset. T o reset Auto-Up: Pull the window switch up and close the window com- pletely , then pull and hold the switch for 1 second.
NOTE: When the engine is running fr om a Remote Start (if equipped), the vehicle must first be unlocked by pressing the remote transmitter UNLOCK button prior to activating the Power Liftgate otherwise the engine will stop automatically . Once unlocked, the liftgate can be opened or closed.
When the remote keyless entry transmitter button is pressed two times and the “Lamp Flash” feature is enabled the turn signals will flash twice to signal that the liftgate is opening or closing. The power liftgate may also be opened by pressing the switch located on the overhead console.
• The power liftgate must be in the full open position in order to power close. If the liftgate is not fully open, press the r emote keyless entry transmitter or overhead console button to fully open the liftgate and then press again to close.
W ARNING! • Driving with the liftgate open can allow poison- ous exhaust gases into your vehicle. Y ou and your passengers could be injured by these fumes.
W ARNING! In a collision, you and your passengers can suffer much greater injuries if you are not properly buckled up. Y ou can strike the interior of your vehicle or other passengers, or you can be thrown out of the vehicle. Always be sure you and others in your vehicle are buckled up properly .
W ARNING! It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts.
Lap/Shoulder Belt Operating Instructions 1. Enter the vehicle and close the door . Sit back and adjust the seat. 2. The seat belt latch plate is above the back of the front seat, next to your arm in the rear seat. Grasp the latch plate and pull out the belt.
W ARNING! • A belt buckled into the wrong buckle will not protect you properly . The lap portion could ride too high on your body , possibly causing internal injuries. Always buckle your belt into the buckle nearest you. • A belt that is too loose will not protect you as well.
W ARNING! • A lap belt worn too high can increase the risk of internal injury in a collision. The belt forces won’t be at the strong hip and pelvic bones, but across your abdomen. Always wear the lap belt as low as pos- sible and keep it snug. • A twisted belt can’t do its job as well.
Adjustable Upper Shoulder Belt Anchorage In the front and second r ow outboard seats, the shoulder belt can be adjusted upwar d or downwar d to help position the belt away from your neck. Push in on the anchorage release button to release the anchorage, and then move it up or down to the position that serves you best.
Second Row Center Seat Belt The center seating position in the second row has a seat belt assembly that can be converted from the normal emergency locking mode to the automatic locking mode. The seat belt should only be used in the automatic locking mode when a child seat is installed at this seating location.
How T o Use The Automatic Locking Mode 1. Buckle the combination lap/shoulder belt. 2. Grasp the shoulder portion and pull downward until the entire belt is extracted. 3. Allow the belt to retract. As the belt retracts, you will hear a clicking sound.
W ARNING! • If the small (keyed buckle) latch plate and keyed buckle are not properly connected when the seat belt is used by an occupant, the seat belt will not be able to provide the proper restraint and will increase the risk of injury in a collision.
T o reattach the seat belt to the third row center seat, pull the small (keyed buckle) latch plate forward from the headliner slots and insert it into the keyed buckle until there is an audible click. Refer to the previous section for the proper seat belt usage.
Seat Belt Pretensioners The seat belts for both front seating positions are equipped with pretensioning devices that are designed to remove any slack from the seat belt system in the event of a collision. These devices improve the performance of the seat belt by assuring that the belt is tight about the occupant early in a collision.
Once the warning is triggered it can be paused if the vehicle speed drops below 5 mph (8 km/h. The warning will be r estarted if the vehicle speed becomes greater than 5 mph.
Seat Belts and Pregnant Women W e recommend that pregnant women use seat belts throughout their pregnancies. Keeping the mother safe is the best way to keep the baby safe. Pregnant women should wear the lap part of the belt across the thighs and as snug against the hips as possible.
Driver And Right Front Passenger Supplemental Restraint System (SRS)—Airbags This vehicle has airbags for both the driver and right front passenger as a supplement to the seat belt restraint systems. The driver’s front airbag is mounted in the steering wheel.
W ARNING! • Do not put anything on or around the front airbag covers or attempt to manually open them. Y ou may damage the airbags and you could be injured because the airbags are no longer functional. These protective covers for the airbag cushions are designed to open only when the airbags are inflat- ing.
Here ar e some simple steps you can follow to minimize the risk of harm from a deploying airbag. 1. Children 12 years and under should always ride buckled up in a rear seat in an appropriate child restraint. Infants in rear-facing child restraints should NEVER ride in the fr ont seat of a vehicle with a passenger front airbag.
W ARNING! • Relying on the airbags alone could lead to more severe injuries in a collision. The airbags work with your seat belt to restrain you properly . In some collisions the airbags won’t deploy at all. Always wear your seat belts even though you have airbags.
How the Airbag System W orks • The Occupant Restraint Controller (ORC) determines if a frontal collision is severe enough to require the airbags to inflate. The fr ont airbag inflators are de- signed to pr ovide differ ent rates of airbag inflation from direction provided by the ORC.
• The Driver and Passenger Airbag/Inflator Units are located in the center of the steering wheel and the right side of the instrument panel. When the ORC detects a collision requiring the airbags, it signals the inflator units. A large quantity of nontoxic gas is generated to inflate the front airbags.
NOTE: At no time should any supplemental restraint system (SRS) component or SRS related component or fastener be modified or replaced with any part except those which are approved by DaimlerChrysler/Mopar .
irritation continues, see your doctor . If these particles settle on your clothing, follow the garment manufac- turer’s instructions for cleaning. • It is not advisable to drive your vehicle after the airbags have deployed. If you are involved in another collision, the airbags will not be in place to protect you.
NOTE: Perchlorate Material – special handling may apply , See www .dtsc.ca.gov/hazardouswaste/per chlorate Enhanced Accident Response System If the airbags deploy after an impact and the electrical .
Event Data Recorder (EDR) EDR will be activated on Fr ont, Side and roll over events. In the event of an accident, your vehicle is designed to recor d up to 5-seconds of specific vehicle data paramete.
provided to the custodial entity upon request. General data that does not identify particular vehicles or crashes may be released for incorporation in aggregate crash databases, such as those maintained by the US govern- ment and various states.
• T raction/stability control status • T ire pressur e monitoring system status (if equipped) Child Restraint Everyone in your vehicle needs to be buckled up all the time - babies and children, too. Every state in the United States and all Canadian provinces require that small children ride in pr oper restraint systems.
by children who weigh more than 20 lbs (9 kg) but are less than one year old. Both types of child restraints are held in the vehicle by the lap/shoulder belt or the LA TCH child restraint anchorage system. (See the LA TCH - Child Seat Anchorage System section.
• Check belt fit periodically . A child’s squirming or slouching can move the belt out of position. • If the shoulder belt contacts the face or neck, move the child closer to the center of the vehicle. Never allow a child to put the shoulder belt under an arm.
around the child restraint so that it is not necessary to use a locking clip. If the seat belt has a cinching latch plate, pulling up on the shoulder portion of the lap/shoulder belt will tighten the belt.
LA TCH - Child Seat Anchorage System (Lower Anchors and T ether for CHildren) Y our vehicle’s second r ow seat is equipped with the child restraint anchorage system called LA TCH.
only install the child restraints using the vehicle’s seat belts. Please refer to the next section for typical installa- tion instructions. Second Row Seat Left Side Second Row Seat Right Side THING.
Installing the LA TCH-Compatible Child Restraint System W e urge that you carefully follow the dir ections of the manufacturer when installing your child r estraint. Not all child r estraint systems will be installed as described her e. Again, carefully follow the installation instructions that were provided with the child restraint system.
NOTE: When using the LA TCH attaching system to install a child restraint, please ensure that all seat belts not being used for occupant r estraints are stowed and out of reach of children. It is recommended that befor e installing the child restraint, buckle the seat belt so the seat belt is tucked behind the child r estraint and out of reach.
Installing Child Restraints Using the V ehicle Seat Belt The second and third row seats have either cinching latch plates or automatic locking retractors which are designed to keep the lap portion tight around the child restraint so that it is not necessary to use a locking clip.
back behind the center seating position. The hooks in the rear floor are NOT designed to withstand the forces that may occur during a crash. W ARNING! An incorrectly anchored tether strap could lead to increased head motion and possible injury to the child.
2. Route the tether strap under the head restraint and between the two headrest posts. 3. Attach the tether strap hook of the child r estraint to the tether anchor located on the seat back and r emove the slack in the tether strap according to the manufacturer ’s instructions.
conditions under which vehicle operations will occur . The r ecommended viscosity and quality grades ar e shown in Section 7. NON-DETERGENT OR STRAIGHT MINERAL OILS MUST NEVER BE USED. A new engine may consume some oil during its first few thousand miles of operation.
compartment. In addition, inspect the exhaust system each time the vehicle is raised for lubrication or oil change. Replace or adjust as requir ed. Safety Checks Y ou Should Make Inside The V ehicle Heater Defroster Ducts Inspect the heater defroster ducts for proper operation.
Safety Checks Y ou Should Make Outside The V ehicle T ires Examine tires for tread wear or uneven wear patterns. Check for stones, nails, glass or other objects lodged in the tread. Inspect for tread cuts or sidewall cracks. Check wheel nuts for tightness and tires for proper pressur e.
I n f o r m a t i o n P r o v i d e d b y :.
UNDERST ANDING THE FEA TURES OF YOUR VEHICLE CONTENTS m Mirrors ............................... 8 3 ▫ Inside Day/Night Mirror ................. 8 3 ▫ Automatic Dimming Mirror — If Equipped .... 8 3 ▫ Outside Mirrors ....................... 8 4 ▫ Exterior Mirrors Folding Feature — If Equipped .
▫ General Information ................... 1 1 4 m Seats ................................ 1 1 4 ▫ Front Seat Manual Seat Adjustment ........ 1 1 4 ▫ Front Seats Manual Seat Recliners .......... 1 1 5 ▫ Manual Lumbar Support Adjustment — If Equipped .
▫ Battery Saver ........................ 1 3 9 ▫ Headlight Delay ...................... 1 3 9 ▫ Automatic Headlights — If Equipped ....... 1 4 0 ▫ Headlights, Parking Lights, Panel Lights ..... 1 4 0 ▫ Illuminated Entry ...................
m Overhead Console W ith Electronic V ehicle Information Center (EVIC) — If Equipped ..... 1 5 9 ▫ Dome/Reading Lights .................. 1 5 9 ▫ Electronic V ehicle Information Center (EVIC) — If Equipped .................. 1 5 9 ▫ Compass/T emperature Button .
MIRRORS Inside Day/Night Mirror The mirror should be adjusted to center on the view through the rear window . A two-point pivot system allows for horizontal and vertical adjustment of the mirror . Annoying headlight glare can be reduced by moving the small control under the mirror to the night position (toward rear of truck).
CAUTION! T o avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror . Apply the solution onto a clean cloth and wipe the mirror clean.
Electric Remote-Control Mirrors The controls for the power mirrors are located on the driver’s door trim panel. T o adjust a mirror , turn the control wand toward the left or right mirror positions indicated. T ilt the control wand in the direction you want the mirror to move.
W ARNING! V ehicles and other objects seen in the right side convex mirror will look smaller and farther away than they really are. Relying too much on your right side mirror could cause you to collide with another vehicle or other object. Use your inside mirror when judging the size or distance of a vehicle seen in the right side mirror .
Heated Mirrors — If Equipped Heated mirrors are automatically activated when you depress the rear window defroster switch located on the instrument panel. The light will illuminate to indicate that the heating elements are ON. T urning Off the rear window defroster or the ignition will deactivate the heated mirrors.
NOTE: The UConnect™ system use requir es a cellular phone equipped with the Bluetooth 9 Hands-Free Profile, 9 version 0.96 or higher . See UConnect™ website for sup- ported phones. NOTE: For UConnect™ customer support, visit the following web sites: • www .
radio or the mirror has the two control buttons (Phone Button and V oice Recognition Button) that will enable you to access the system. V oice Recognition Button Actual button location may vary with radio. The individual buttons are described in the “Operation” section.
• For certain operations, compound commands can be used. For example, instead of saying 9 Setup 9 and then 9 Phone Pairing, 9 the following compound command can be said: 9 Setup Phone Pairing. 9 • For each feature explanation in this section, only the combined form of the voice command is given.
T o complete the pairing process, you will need to refer- ence your cellular phone owner’s manual. The UCon- nect™ website may also provide detailed instructions for pairing. The following are general phone to UConnect™ System pairing instructions: • Press the “Phone” button to begin.
Dial by Saying a Number • Press the “Phone” button to begin. • After the 9 Ready 9 prompt and the following beep, say 9 Dial. 9 • System will pr ompt you to say the number you want call. • For example, you can say 9 234-567-8901. 9 The phone number that you enter must be of valid length and combination.
Add Names to Y our UConnect™ Phonebook NOTE: Adding names to phone book is recommended when vehicle is not in motion. • Press the “Phone” button to begin. • After the 9 Ready 9 prompt and the following beep, say 9 Phonebook New Entry . 9 • When pr ompted, say the name of the new entry .
Exchange Profile (OBEX). Please see your phone owners’ manual for specific instructions on how to send these entries from your phone. NOTE: • Phone handset must support Bluetooth OBEX trans- fers of phonebook entries to use this feature.
9 Phonebook Edit 9 can be used to add another phone number to a name entry that already exists in the phonebook. For example, the entry John Doe may have a mobile and a home number , but you can add John Doe’s work number later using the 9 Phonebook Edit 9 feature.
• After confirmation, the phone book entries will be deleted. • Note that only the phone book in the current language is deleted. List All Names in the UConnect™ Phonebook • Press the “Phone” button to begin. • After the 9 Ready 9 prompt and the following beep, say 9 Phonebook List Names.
call, press and hold the ’Phone’ button until you hear a single beep indicating that the incoming call was rejected. Answer or Reject an Incoming Call - Call Currently in Progress If a call is cur.
Conference Call When two calls are in pr ogress (one active and one on hold), press and hold the “Phone” button until you hear a double beep indicating that the two calls have been joined into one conference call.
Call Continuation Call continuation is pr ogression of a phone call on UConnect™ system after the vehicle ignition key has been switched to off. Call continuation functionality available on the vehi.
Emergency Assistance If you are in an emergency and the mobile phone is reachable: • Pick up the phone and manually dial the emergency number for your area. If the phone is not reachable and the UConnect™ system is operational, you may reach the emer gency number as follows: • Press the “Phone” button to begin.
Please r efer to the 24-Hour “T owing Assistance” cover- age details in the W arranty information booklet and on the 24–Hour T owing Assistance Card.
entries. T o use this feature, dial the number you wish to call and then press the “V oice Recognition” button and say “Send.” The system will prompt you to enter the name or number , say the name of the phonebook entry you wish to send.
notification to inform you of your phone and network status when you are attempting to make a phone call using UConnect™. The status is given for roaming, network signal strength, phone battery strength, etc.
Advanced Phone Connectivity T ransfer Call to and from Cellular Phone The UConnect™ system allows on going calls to be transferred from your cellular phone to the UConnect™ system without terminating the call.
• Press the “Phone” button to begin. • After the 9 Ready 9 prompt and the following beep, say 9 Setup Select Phone 9 and follow the prompts. • Y ou can also press the “V oice Recognition” button anytime while the list is being played, and then choose the phone that you wish to select.
From outside the UConnect™ mode (e.g. from radio mode) • Press and hold the “V oice Recognition” button for 5 seconds until the session begins, or , • Press the “V oice Recognition” button and say 9 Setup, V oice T raining 9 command. Repeat the words and phrases when prompted by the UConnect™ system.
• fully closed windows, • dry weather condition. • Even though the system is designed for users speaking in North American English, French, and Spanish ac- cents, the system may not always work for some.
• dry weather condition. • operation from driver seat. • Performance, such as audio clarity , echo, and loudness to a large degree rely on the phone and network, and not the UConnect™ system. • Echo at far end can sometime be reduced by lowering the in-vehicle audio volume.
UNDERST ANDING THE FEA TURES OF YOUR VEHICLE 109 3 I n f o r m a t i o n P r o v i d e d b y :.
1 10 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE I n f o r m a t i o n P r o v i d e d b y :.
UNDERST ANDING THE FEA TURES OF YOUR VEHICLE 11 1 3 I n f o r m a t i o n P r o v i d e d b y :.
V oice Commands Primary Alternate(s) zero one two three four five six seven eight nine star (*) plus (+) pound (#) add location all V oice Commands Primary Alternate(s) call cancel confirmation prompts.
V oice Commands Primary Alternate(s) language list names list phones mobile mute mute off new entry no pager pair a phone phone pairing pairing phonebook phone book previous recor d again V oice Comma.
General Information This device complies with part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following conditions: • This device may not cause harmful interference. • This device must accept any interference received, including interference that may cause undesired op- eration.
W ARNING! Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured. Adjust any seat only while the vehicle is parked.
Manual Lumbar Support Adjustment — If Equipped The manual lumbar support adjustment lever is located on the right side of the driver seat and on the left side of the passenger’s seat. Moving the lumbar control lever fore and aft increases or decreases the lumbar support.
8 - W ay Driver’s Power Seat — If Equipped The driver power seat switches are located on the left side of the driver seat lower side trim. The bottom switch controls up/down, forward/rearwar d, and tilt adjust- ment. The top switch controls the seatback recline adjust- ment.
4 - W ay Passenger’s Power Seat — If Equipped The front passenger’s power seat switches are located on the right side of the passenger seat lower side trim. The bottom switch contr ols forward/rearwar d adjustment. The top switch controls the seatback recline adjustment.
The front heated seat system allows the driver and front passenger to select from two differ ent levels of supple- mental electrical seat heating, or no seat heating to suit their individual comfort requir ements.
off. Both of the indicators on identifies High heat level. The lower indicator on only , identifies Low heat level. NOTE: The high heat setting will operate for appr oxi- mately 30 minutes. After 30 minutes, the system will automatically transition to the low heat setting.
Second Row Bucket Seats — Fold and T umble Second row bucket seats have seatback recliners on both seating positions. Raising the lever allows the seatback to be reclined an additional 1 1 degrees. The second r ow bucket seats can be folded and tumbled forward for easy access to the third seat or rear cargo area.
4. Pull up on the release handle and lift to tumble the seat fully forwar d. If the seat contacts the rear of the front seat, move the front seat forward. T o relatch the seat, tilt the seat rearward and push down firmly to engage the r ear attachments.
W ARNING! In a collision, you or others in your vehicle could be injured if seats are not properly latched to their floor attachments. Always be sure the seats are fully latched. Second Row 40/20/40 Seat — Fold and T umble The 40/20/40 seat configuration is standard on all mod- els.
T o Fold the 40% seatbacks fully raise the lever on the side of the seat to release the seatback. The seatback can now be folded into the down position for use as a cargo floor , or the seat can now be tumbled forward to allow access to the rear of the vehicle.
T o T umble the 40% seat, fully raise the lever on the side of the seat to release the floor latches and tumble the seat. W ARNING! Do not drive the vehicle with the outer 40% second row seats in the tumbled position. The outer 40% second row seats are only intended to be tumbled for entry and exit to the third row seat.
NOTE: The seatback must be fully folded into the down position to allow the lever to be raised enough to release the floor latches. T o Fold and T umble the 2nd r ow 40% seats fr om the 3rd row , fully raise the lever at the rear of the seat to fold the seatback.
Seat Cushion Pockets Seat Cushion Movement Up And Forward UNDERST ANDING THE FEA TURES OF YOUR VEHICLE 127 3 I n f o r m a t i o n P r o v i d e d b y :.
CAUTION! When loading cargo into the rear of you vehicle with the 3rd row seat folded flat, be careful not to damage the material on the head restraints. NOTE: The seat belt buckles are hinged to fold with the seat back. W ARNING! Do not sit in the third row seat unless the cushion and back are properly engaged.
Third Row 60/40 Folding — If Equipped Third Row Seat Third Row Seat 40% Seatback Fold UNDERST ANDING THE FEA TURES OF YOUR VEHICLE 129 3 I n f o r m a t i o n P r o v i d e d b y :.
Third Row Seat Features Third Row Seat Folded Forward 130 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE I n f o r m a t i o n P r o v i d e d b y :.
DRIVER MEMOR Y SYSTEM — IF EQUIPPED Once programmed, the memory buttons 1 and 2 on the driver’s door panel can be used to recall the driver’s seat position, driver’s outside mirr or position, adjustable brake and accelerator pedals position, Automatic T em- perature Control (A TC) temperature and radio station preset settings.
linked to either memory position. The memory system can accommodate up to two transmitters, each transmit- ter linked to either of the two memory positions.
NOTE: A chime sound may be heard if Setting Memory was inhibited for any reason. Memory Position Recall NOTE: • The driver’s seat belt must be unbuckled to recall memory positions. • The vehicle must be in Park to recall memory posi- tions. • Not all motors may be moved at one time.
T o Disable A T ransmitter Linked to Memory 1. T urn the ignition switch to the OFF position and remove the key . 2. Press and release the memory SET (S) button located on the driver’s door . 3. W ithin 10 seconds, press and r elease the UNLOCK button on the Remote Keyless Entry transmitter .
Driver Easy Exit and Easy Entry Control This additional feature provides automatic driver’s seat positioning which will enhance driver mobility out of and into the vehicle. The seat cushion will move rear - ward approximately 2.5 inches (60 mm) when the key is removed from the ignition switch.
Then push the safety latch lever to the left. It is located between the grille and hood opening right of the center . T o prevent possible damage, do not slam the hood to close it. Use a firm downwar d push at the center fr ont edge of the hood to ensure that both latches engage.
LIGHTS Headlight Switch Location Headlight Switch UNDERST ANDING THE FEA TURES OF YOUR VEHICLE 137 3 I n f o r m a t i o n P r o v i d e d b y :.
Interior Lights Courtesy and dome lights are turned on when the front doors are opened, when the dimmer control (r otating wheel on the right side of the switch) is rotated to the second upwar d detent position, or when the UNLOCK button is pressed on the key fob.
Battery Saver T o pr otect the life of your vehicle’s battery , Load Shed- ding is provided for both the interior and exterior lights. If the ignition is off and any door is left ajar for eight minutes or the dimmer control is rotated upwards for 15 minutes, the interior lights will automatically turn off.
Automatic Headlights — If Equipped Automatic Headlights can be activated by rotating the rotary headlight switch to the symbol “A.” The head- lights will turn on when the engine is running and the ambient light sensor indicates that the headlights should be activated.
Daytime Running Lights (Canada Only) The headlights on your vehicle will illuminate when the engine is started. This provides a constant “Lights ON” condition until the ignition is turned OFF . The lights illuminate at reduced intensity . If the parking brake is applied the Daytime Running Lights will turn of f.
indicator light located in the instrument cluster will illuminate when the fog lights are on. The fog lights will turn off when the switch is pressed in, when the head- light switch is rotated to the OFF position, or the high beam is selected.
T urn Signal Auto-Mode T ap the multi-function control lever once and the turn signal (left or right) will flash 3 times, and automatically turn off. Passing Light Y ou can signal another vehicle with your headlights by partially pulling the multifunction lever towar d the steer- ing wheel.
WINDSHIELD WIPERS AND W ASHERS Windshield Wipers The wipers and washers are operated by a switch in the multifunction control lever . T urn the end of the handle to select the desired wiper speed.
W ARNING! Sudden loss of visibility through the windshield could lead to an accident. Y ou might not see other vehicles or other obstacles. T o avoid sudden icing of the windshield during freezing weather , warm the windshield with defroster before and during wind- shield washer use.
Windshield W ashers T o use the washer , push in on the washer knob on the end of the multifunction contr ol lever and hold while spray is desired. If the washer knob is depressed while in the delay range, the wiper will operate for several seconds after the washer knob is released.
TIL T STEERING COLUMN T o tilt the column, pull rearwar d on the lever below the turn signal control and move the wheel up or down, as desired. Push the lever forwar d to lock the column firmly in place. W ARNING! T ilting the steering column while the vehicle is moving is dangerous.
DRIVER ADJUST ABLE PEDALS — IF EQUIPPED The power adjustable accelerator and brake pedals allow the driver to establish a comfortable position relative to the steering wheel and pedals. Adjustment 1. Position the driver seat so that you ar e at least 10 inches (254 mm) away from the airbag located in the center of the steering wheel.
CAUTION! Do not place any article under the adjustable pedals or impede its ability to move as it may cause damage to the pedal controls. Pedal travel may become lim- ited if movement is stopped by an obstruction in the adjustable pedal’s path.
can be reactivated by pushing the speed control switch ON / OFF button and re-establishing the desired vehicle SET speed. Push the ON/OFF button to the ON position.
T o V ary The Speed Setting When the speed control is on, speed can be increased by pressing and holding the ACCEL button. When the button is released, a new set speed will be established. T apping the ACCEL button once will result in a speed increase (refer to the table below for the speed for your specific engine).
T o Accelerate For Passing Depress the accelerator as you would normally . When the pedal is released, the vehicle will return to the set speed. NOTE: When driving uphill, at elevations above 2,000 feet (610 meters), or when the vehicle is heavily loaded (especially when towing) the vehicle may slow below the SET speed.
When the driver selects Reverse the system scans for objects behind the vehicle using four sensors located in the rear bumper . Objects can be detected from up to 78.7 inches (200 cm). A warning display above the rear window provides both visible and audible warnings indicating the range of the object.
W ARNING DISPLA Y DIST ANCES DISPLA Y LED OBST ACLE DIST ANCE FROM: LED COLOR AUDIBLE SIGNAL REAR CORNERS REAR CENTER 1st LED 78.7 in. (200 cm) Y ellow None 2nd LED 51.1 in. (130 cm) Y ellow None 3rd LED 45.2 in. (1 15 cm) Y ellow None 4th LED 31.5 in.
W ARNING! • Drivers must be careful when backing up even when using the Rear Park Assist System. Always check carefully behind your vehicle, look behind you, and be sure to check for pedestrians, animals, other vehicles, obstructions, and blind spots before backing up.
• Jackhammers, large trucks, and other vibrations could affect the performance of the system. If “Service Park Assist System” appears in the Electronic V ehicle Information Center (EVIC) after making sure the rear bumper is clean please see your authorized dealer .
W ARNING! Drivers must be careful when backing up even when using the Rear Camera System. Always check care- fully behind your vehicle, and be sure to check for pedestrians, animals, other vehicles, obstructions, or blind spots before backing up.
OVERHEAD CONSOLE The overhead console has the following features: • Courtesy Lights • Garage Door Opener — If Equipped • Electronic V ehicle Information Center (EVIC) — If Equipped Courtesy/Reading Lights Near the front of the console is one courtesy and two reading lights.
OVERHEAD CONSOLE WITH ELECTRONIC VEHICLE INFORMA TION CENTER (EVIC) — IF EQUIPPED The overhead console contains dome/r eading lights, and an Electronic V ehicle Information Center (EVIC). Dome/Reading Lights Located in the overhead console are two dome/reading lights.
T rip Functions Pressing the STEP button allows you to scroll through one of the following T rip Function features: • TRIP – Shows the total distance traveled since the last reset. T o reset the TRIP function, pr ess and hold the RESET button. • ELAPSED TIME – Shows the total elapsed time of travel since the last reset.
NOTE: Significant changes in driving style or vehicle loading will greatly affect the actual drivable distance of the vehicle, regar dless of the DTE displayed value. • When the DTE value is less than 30 miles (48 km) estimated driving distance, the DTE display will change to a text display of 9 LOW FUEL.
OIL CHANGE REQUIRED — If Equipped Y our vehicle is equipped with an engine oil change indicator system. The “Oil Change Required” message will flash in the EVIC display for approximately 10 seconds after a single chime has sounded to indicate the next scheduled oil change interval.
Use the STEP button to display one of the following: • “LANGUAGE” – When in this display you may select one of several different languages for all display nomenclature, including the trip functions. Press the RESET button while in this display to select your preferr ed language.
• “SOUND HORN W/LOCK > YES” – When ON is selected, a short horn sound will occur when the remote keyless entry “Lock” button is pressed. This feature may be selected with or without the flash lights on lock/unlock feature. T o make your selection, press and release the RESET button until “ON” or “OFF” appears.
• “KEY OFF POWER DELA Y > OFF” – When this feature is selected, the power window switches, radio, hands–free system (if equipped), and power outlets will remain active for up to 60 minutes after the ignition switch is turned of f. Opening a vehicle door will cancel this feature.
Compass/T emperature Button Pressing the Compass/T emperature button will return the display to the normal compass/ temperature display . NOTE: T emperature accuracy can be effected from heat soak. For best accuracy , the vehicle should be driven at a speed greater than 20 mph (32 km/h) for several min- utes.
metallic objects) until the “CAL” message turns off. The compass will now function normally . Compass V ariance Compass V ariance is the differ ence between magnetic North and Geographic North. In some ar eas of the country , the differ ence between magnetic and geographic North is great enough to cause the compass to give false readings.
1. T urn the ignition switch to the ON/RUN position. 2. Press the menu button until Personal Set- tings is displayed. 3. Press the STEP button until “Compass V ariance” is displayed. 4. Press and release RESET button until the proper variance zone is selected according to the variance map.
W ARNING! V ehicle exhaust contains carbon monoxide, a danger- ous gas. Do not run your vehicle in the garage while training the transceiver . Exhaust gas can cause seri- ous injury or death. Programming HomeLink T Before Y ou Begin If you have not trained any of the HomeLink t buttons, erase all channels before you begin training.
If the EVIC display states “DID NOT TRAIN” r epeat Step 3. If the signal is too weak, replace the battery in the original hand-held transmitter . It may take up to 30 seconds, or longer in rare cases. The garage door may open & close while you train.
6. Firmly press and release the “learn” or “training” button. The name and color of the button may vary by manufacturer . NOTE: There ar e 30 seconds in which to initiate the next step after the “Learn” button has been pressed.
Similar to this Canadian law , some U.S. gate operators ar e designed to “time-out” in the same manner . It may be helpful to unplug the device during the cycling process to pr event possible overheating of the garage door or gate motor .
3. W ithout releasing the button, proceed with PRO- GRAMMING HOMELINK Step #2 and follow all remain- ing steps. Security It is advised to erase all channels before you sell or turn in your vehicle. T o do this, press and hold the two outside buttons for 20 seconds until the EVIC message states “CHANNELS CLEARED.
NOTE: The transmitter has been tested and it complies with FCC and IC rules. Changes or modifications not expressly approved by the party r esponsible for compli- ance could void the user ’s authority to operate the device.
Express Open Feature During the Express Open operation, any movement of the switch will stop the sunr oof and it will remain in a partial open position. Again, momentarily pressing the switch rearwar d will activate the Expr ess Open Feature. T o close the sunr oof, hold the switch in the forward position.
W ARNING! In an accident, there is a greater risk of being thrown from a vehicle with an open sunroof. Y ou could also be seriously injured or killed. Always fasten your seat belt properly and make sure all passengers are properly secured too. Do not allow small children to operate the sunroof.
ELECTRICAL POWER OUTLETS This vehicle has three auxiliary power outlets that can provide up to 20 Amps of current for accessories de- signed for use with the standard power outlet adapters. The outlet located in the lower portion of the instrument panel has a snap on plastic cap so that it can be covered when not in use.
NOTE: When the Inverter Switch is pressed, ther e will be a delay of approximately 1 second before the inverter status indicator turns ON. The status Indicator of the AC power inverter indicates whether the inverter is produc- ing AC power . NOTE: Due to build in overload protection the inverter will shut down if the power rating is exceeded.
Electrical Outlet Use With Engine OFF (Battery Fed Configuration) CAUTION! • Many accessories that can be plugged in draw power from the vehicle’s battery , even when not in use (i.
Reconfiguring Power Outlets T o reconfigur e the outlets, be sure the ignition is OFF before removing the fuse. The r econfigurable fuse loca- tion is a special design that allows the fuse to be installed in two differ ent ways. If the fuse is located in the 9 Upper or T op Position 9 the outlets will work at all times.
FLOOR CONSOLE Floor Console Features The Floor Console between the driver’s and front pas- senger’s seat, has the following features: • Miscellaneous storage compartments • Flexible cup holder.
third row occupants. The four cupholders located in the center console may be removed for cleaning. Power Outlet and Portable Phone Storage The console is equipped with a power outlet, portable phone storage bin, and phone cord routing. The phone storage bin can be used when easy access to the phone is needed.
T o access the storage bin, lift up on the console door latch. F ACTOR Y INST ALLED ROOF LUGGAGE RACK The load carried on the roof when equipped with a luggage rack must not exceed 68 kg (150 lbs.), and should be uniformly distributed over the cargo area.
The side rails between the stantions should be used to tie down cargo. Check the straps frequently to be sure that the load remains securely attached. NOTE: Crossbars are offer ed by Mopar t accessories. External racks do not increase the total load carrying capacity of the vehicle.
W ARNING! Cargo must be securely tied before driving your vehicle. Improperly secured loads can fly off the vehicle, particularly at high speeds, resulting in per- sonal injury or property damage. Follow the roof rack Cautions when carrying cargo on your roof rack.
T o open the side cover , pull on the cover latch, and attach the cord to the upper cargo net hook. T o open the main cover , pull up on the latch, and attach the cord to the rear seat head restraint post. T o open the Cargo divider , lift up on the car go divider handles, raising the doors to the full open position.
INSTRUMENT P ANEL AND CONTROLS CONTENTS m Instruments And Controls ................. 1 9 1 m Instrument Cluster ...................... 1 9 2 m Instrument Cluster Description ............. 1 9 3 m Electronic Digital Clock .................. 2 0 4 ▫ Clock Setting Procedur e.
m Sales Code RES — AM/FM Stereo Radio W ith CD Player (MP3 AUX Jack) ................ 2 0 9 ▫ Operating Instructions - Radio Mode ....... 2 0 9 ▫ Operation Instructions - CD Mode For CD And MP3 Audio Play .................. 2 1 5 ▫ Notes On Playing MP3 Files .
▫ List Or Browse Mode .................. 2 4 3 m V ideo Entertainment System (Sales Code XR V) — If Equipped ............ 2 4 4 m Satellite Radio — If Equipped .............. 2 4 4 ▫ System Activation ..................... 2 4 5 ▫ Electronic Serial Number/Sirius Identification Number (ESN/SID) .
▫ Air Conditioning Operation .............. 2 5 2 ▫ Front Blower Control ................... 2 5 2 ▫ Front Mode Control ................... 2 5 3 ▫ Rear T emperature Control — If Equipped .... 2 5 5 ▫ Rear W indow Defrosting And Rear W indow W asher/W iper .
INSTRUMENTS AND CONTROLS INSTRUMENT P ANEL AND CONTROLS 191 4 I n f o r m a t i o n P r o v i d e d b y :.
Instrument Cluster 192 INSTRUMENT P ANEL AND CONTROLS I n f o r m a t i o n P r o v i d e d b y :.
INSTRUMENT CLUSTER DESCRIPTION 1. Fuel Gage The fuel gauge shows level of fuel in tank when ignition switch is in the ON position. 2. T emperature Gage The temperature gage indicates engine coolant temperature. Any reading within the normal range indicates that the cooling system is operat- ing satisfactorily .
left/right turn signal is left on with the engine RPM vehicle speed greater than 15 mph (24 km/h) for more than one mile. 4. Low Fuel W arning Light This indicator lights when the fuel gauge reads 1/16 of a tank or less. 5. High Beam Indicator Indicates that headlights are on high beam.
W ARNING! A hot engine cooling system is dangerous. Y ou or others could be badly burned by steam or boiling coolant. Y ou may want to call a service center if your vehicle overheats. If you decide to look under the hood yourself, see Section 7 of this manual.
illuminates and the ABS is switched off. When the voltage is above this value again, the malfunction indi- cator light should go out and the ABS is operational. If the malfunction indicator light stays illuminated, have the system checked at your authorized dealer as soon as possible.
The two trip odometers show individual trip mileage. T o switch from odometer to trip odometers, press and release the T rip Odometer button. T o reset a trip odometer , display the desired trip odom- eter to be reset then push and hold the button until the display resets (approximately 2 seconds).
Unless reset, this message will continue to display each time you turn the ignition switch to the ON/RUN position. T o turn off the message temporarily , press and release the T rip Odometer button on the instrument cluster . T o r eset the oil change indicator system (after performing the scheduled maintenance) refer to the fol- lowing procedur e.
9 ESP/TCS Indicator Light 9 starts to flash as soon as the tires lose traction and the ESP system becomes active. The 9 ESP/TCS Indicator Light 9 also flashes when TCS is active. If the 9 ESP/TCS Indicator Light 9 begins to flash during acceleration, ease up on the accelerator and apply as little throttle as possible.
have the bulb repaired pr omptly . If the light stays on, it may be an indication that the parking brake has not been released, or ther e is a low brake fluid level.
23. Malfunction Indicator Light This light is part of an onboard diagnostic system which monitors the emissions and engine control system. If the vehicle is ready for emissions testing the light will come on when the ignition is first turned on and remain on, as a bulb check, until the engine is started.
As an added safety feature, your vehicle has been equipped with a tire pressure monitoring system (TPMS) that illuminates a low tire pressure telltale when one or more of your tires are significantly under-inflated.
CAUTION! The TPMS has been optimized for the original equipment tires and wheels. TPMS pressures and warning have been established for the tire size equipped on your vehicle. Undesirable system opera- tion or sensor damage may result when using re- placement equipment that is not of the same size, type, and/or style.
30. 4LOW Indicator Indicates transfer case is in 4LOW position. 31. Odometer/T rip Odometer Button Press this button to toggle between the odometer and the trip odometer display . Holding the button in resets the trip odometer reading. ELECTRONIC DIGIT AL CLOCK The clock and radio each use the display panel built into the radio.
RADIO GENERAL INFORMA TION Radio Broadcast Signals Y our new radio will provide excellent reception under most operating conditions. Like any system, however , car radios have performance limitations, due to mobile op- eration and natural phenomena, which might lead you to believe your sound system is malfunctioning.
will remain active for up to 10 minutes after the ignition switch has been turned off. Opening a vehicle front door will cancel this feature. SALES CODE REN — MUL TIMEDIA SYSTEM — IF EQUIPPED NOTE: The sales code is located on the lower right side of the unit’s faceplate.
Operating Instructions — Satellite Radio (If Equipped) Refer to your Radio Specific User’s Manual for detailed operating instructions. Operating Instructions — Hands-Free Communication (UConnect™) (If Equipped) Refer to “Hands-Free Communication (UConnect™)” in Section 3 of this manual for detailed operating instructions.
3. When this feature is on, a check mark will appear in the box next to the words “Daylight Savings.” T ouch the screen where the words “Daylight Savings” are dis- played to change the current setting. Show T ime if Radio is Off When selected, this feature will display the time of day on the touch screen when the system is turned off.
SALES CODE RES — AM/FM STEREO RADIO WITH CD PLA YER (MP3 AUX JACK) NOTE: The radio sales code is located on the lower right side of your radio faceplate. Operating Instructions - Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio.
to seek up and the left switch to seek down. The radio will remain tuned to the new station until you make another selection. Holding either button will bypass stations without stopping until you release it.
3. After adjusting the hours, press the right side TUNE control knob to set the minutes. The minutes will begin to blink. 4. Adjust the minutes using the right side TUNE control knob. Press the TUNE contr ol knob to save time change. 5. T o exit, press any button/knob or wait 5 seconds.
Press the rotary TUNE control knob a third time and TREBLE will display . T urn the TUNE control knob to the right or left to increase or decrease the T reble tones.
Program T ype 16 Digit-Character Display Nostalgia Nostalga Oldies Oldies Personality Persnlty Public Public Rhythm and Blues R & B Religious Music Rel Musc Religious T alk Rel T alk Rock Rock Sof.
AM and FM Buttons Press the buttons to select AM or FM Modes. SET Button — T o Set the Push-Button Memory When you are receiving a station that you wish to commit to push-button memory , press the SET button. The symbol SET 1 will now show in the display window .
Operation Instructions - CD MODE for CD and MP3 Audio Play NOTE: The ignition switch must be in the ON or ACC position to operate the radio. NOTE: This Radio is capable of playing compact discs (CD), .
EJECT Button - Ejecting a CD Press the EJECT button to eject the CD. If you have ejected a disc and have not removed it within 10 seconds, it will be reloaded. If the CD is not removed, the radio will reinsert the CD but will not play it. A disc can be ejected with the radio and ignition OFF .
RND Button (Random Play Button) Press this button while the CD is playing to activate Random Play . This feature plays the selections on the compact disc in random order to provide an interesting change of pace. Press the right SEEK button to move to the next ran- domly selected track.
• Maximum number of characters in file/folder names: • Level 1: 12 (including a separator 9 . 9 and a 3-character extension) • Level 2: 31 (including a separator 9 . 9 and a 3-character extension) Multisession disc formats are supported by the radio.
Playlist files are not supported. MP3 Pro files are not supported. Playback of MP3 Files When a medium containing MP3 data is loaded, the radio checks all files on the medium. If the medium contains a lot of folders or files, the radio will take more time to start playing the MP3 files.
Press the INFO button once more to r eturn to 9 elapsed time 9 priority mode. Press and hold the INFO button for 3 seconds or mor e and radio will display song titles for each file. Press and hold the INFO button again for 3 seconds to return to 9 elapsed time 9 display .
SALES CODE REQ — AM/FM STEREO RADIO AND 6–DISC CD/DVD CHANGER (MP3/WMA AUX JACK) NOTE: The radio sales code is located on the lower right side of your radio faceplate. Operating Instructions - Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio.
will remain tuned to the new station until you make another selection. Holding either button will bypass stations without stopping until you release it.
3. After adjusting the hours, press the right side TUNE control knob to set the minutes. The minutes will begin to blink. 4. Adjust the minutes using the right side TUNE control knob. Press the TUNE contr ol knob to save time change. 5. T o exit, press any button/knob or wait 5 seconds.
Press the rotary TUNE control knob a third time and TREBLE will display . T urn the TUNE control knob to the right or left to increase or decrease the T reble tones.
Program T ype 16 Digit-Character Display Nostalgia Nostalga Oldies Oldies Personality Persnlty Public Public Rhythm and Blues R & B Religious Music Rel Musc Religious T alk Rel T alk Rock Rock Sof.
• DVD Enter - When the disc is in DVD Menu mode, selecting DVD Enter will allow you to play the current highlighted selection. Use the remote control to scroll up and down the menu (If Equipped). • DISC Play/Pause - Y ou can toggle between playing the DVD and pausing the DVD by pushing the SELECT button (If Equipped).
• Player Defaults - Selecting this item will allow the user to scroll through the following items, and set defaults according to customer preference. Menu Language — If Equipped Selecting this item will allow the user to choose the default startup DVD menu language (effective only if language supported by disc).
Audio DRC — If Equipped Selecting this item will allow the user to limit maximum audio dynamic range - The default is set to 9 High, 9 and under this setting, dialogues will play at 1 1 db higher than if the setting is 9 Normal.
window . Each button can be set for SET 1 and SET 2 in both AM and FM. This allows a total of 12 AM, 12 FM, and 12 Satellite (if equipped) stations to be stored into push-button memory . The stations stored in SET 2 memory can be selected by pressing the push-button twice.
NOTE: The ignition switch must be in the ON or ACC position to operate the radio. LOAD Button — Loading Compact Disc(s) Press the LOAD button and the push-button with the corresponding number (1-6) where the CD is being loaded. The radio will display PLEASE W AIT and prompt when to INSERT DISC.
SCAN Button (CD MODE) Press the Scan button to scan through each track on the CD currently playing. TIME Button (CD MODE) Press this button to change the display from a large CD playing time display to a small CD playing time display .
The radio uses the following limits for file systems: • Maximum number of directory levels: 8 • Maximum number of files: 255 • Maximum number of folders: 100 • Maximum number of characters in file/folder names: • Level 1: 12 (including a separator 9 .
MPEG Specification Sampling Fre- quency (kHz) Bit rate (kbps) MPEG-1 Audio Layer 3 48, 44.1, 32 320, 256, 224, 192, 160, 128, 1 12, 96, 80, 64, 56, 48 MPEG-2 Audio Layer 3 24, 22.05, 16 160, 128, 144, 1 12, 96, 80, 64, 56, 48 WMA Specification Sampling Fre- quency (kHz) Bit Rate (kbps) WMA 44.
LIST Button (DISC Mode for MP3/WMA Play) Pressing the LIST button will bring up a list of all folders on the disc. Scrolling up or down the list is done by turning the TUNE contr ol knob.
SCAN Button (Auxiliary Mode) No function. EJECT Button (Auxiliary Mode) No function. TIME Button (Auxiliary Mode) Press this button to change the display from elapsed playing time to time of day . The time of day will display for 5 seconds. R W/FF (Auxiliary Mode) No function.
Macrovision This product incorporates copyright pr otection technol- ogy that is protected by U.S. patents and other intellec- tual property rights. Use of this copyright protection technology must be authorized by Macrovision, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision.
music and photos from CDs or through the USB port. While the Gracenote database finds the artist, track, and title for the music. An auxiliary input jack permits passengers to listen to a portable MP3 player thr ough the vehicle’s speakers.
Changing the T ime Zone 1. T urn on the system. 2. T ouch the screen where the time is displayed. The clock setting menu will appear on the screen. If the wor ds “T ime: GPS T ime” are displayed at the top of the screen, proceed to Step 4. Otherwise, proceed to Step 3.
2. T ouch the screen where the time is displayed. The clock setting menu will appear on the screen. If the wor ds “T ime: User Clock” are displayed at the top of the scr een, proceed to Step 4.
UNIVERSAL CONSUMER INTERF ACE (UCI) — IF EQUIPPED NOTE: This section is for sales code RES and REQ radios only with UConnect.™ For sales code REN touch screen radio, refer to the separate User’s Manual.
Play Mode When switched to UCI mode the iPod t will be in Play mode . In this Play mode , you may use the following buttons on the radio faceplate to contr ol the iPod t and display data: TUNE/SCROLL Knob Use the “TUNE/SCROLL” knob to go to the next or previous track.
previous track in the list, if you press this button at any other time in the current track it will go back to the beginning of the track. If the right (up) button is pressed during Play mode, it will go to the next track in the list.
List or Browse Mode During Play mode, pressing any of the following buttons will take you to List mode. List mode enables you to scroll through the list of menus and tracks on the iPod t . TUNE/SCROLL Knob In the List mode, the “TUNE/SCROLL” knob functions in a similar manner as the scroll wheel on the iPod t .
T o exit the List mode without selecting a track, press the same preset button again to go back to Play mode. LIST Button Pressing the “LIST” button will take to the top level menu of the iPod t . This takes you to the same top level menu as on your iPod t .
System Activation Sirius Satellite Radio service is pre-activated, and you may begin listening immediately to the one year of SIRIUS audio service that is included with the factory- installed satellite radio system in your vehicle.
ESN/SID Access with RAQ and RAK Radios W ith the ignition switch in the ACCESSORY position and the radio OFF , press the CD Eject and TIME buttons simultaneously for 3 seconds.
Selecting a Channel Press and release the SEEK or TUNE knob to search for the next channel. Press the top of the button to search up and the bottom of the button to search down. Holding the TUNE button causes the radio to bypass channels until the button is released.
NOTE: Pressing the 9 SEEK 9 or 9 SCAN 9 button, while performing a music type scan, will change the channel by one and stop the sear ch. Pr essing a pre-set memory button during a music type scan, will call up the memory channel and stop the search.
REMOTE SOUND SYSTEM CONTROLS — IF EQUIPPED The remote sound system controls ar e located on the rear surface of the steering wheel. The left- and right-hand controls are rocker-type switches with a push-button in the center of each switch. Reach behind the steering wheel to access the switches.
Left-Hand Switch Functions for Media (i.e. CD) Operation • Press the top of the switch once to listen to the next track. • Press the bottom of the switch once either to listen to the beginning of the curr ent track or to listen to the beginning of the previous track if it is within one second after the current track begins to play .
NOTE: If you experience difficulty in playing a particu- lar disc, it may be damaged (i.e. scratched, reflective coating removed, a hair , moisture or dew on the disc) oversized, or have theft pr otection encoding. T ry a known good disc before considering disc player service.
Air Conditioning Operation T o turn the air conditioning On or Off perform the following steps: • Position the mode control button to the desired airflow setting. • Set the front blower control to any desired speed. • Press the Snowflake (A/C) button which is located to the right of the temperature control slide.
Front Mode Control The mode control allows you to choose from several patterns of air distribution. NOTE: T o improve your selection choices, the system allows you to operate at intermediate positions between the major modes. These intermediate positions are iden- tified by the small dots and give an even blend of both modes.
Bi-Level Air flows thr ough the outlets located in the instru- ment panel and those located on the floor . NOTE: There is a dif ference in temperatur e between the upper and lower outlets for added comfort. The warmer air goes to the floor outlets. This featur e gives improved comfort during sunny but cool conditions.
T emperature Control The temperature of the air is controlled by a slide located on the top center of the control panel. Move the slide left or right to change the temperature. The blue area of the scale indicates cooler temperatures while the r ed ar ea indicates warmer temperatures.
mode on the front contr ol will give you air from the outlets in the headliner in the rear . Floor mode in the front will give you floor in the rear . Rear Window Defrosting and Rear Window W asher/Wiper See the “Rear W indow Features” section of this book.
Automatic Control The A TC system can maintain a steady comfort level in various weather conditions with a simple operation: • Select your desired temperature setting by pressing the + or - side of the TEMP rocker switches. A digital temperature setting for driver and passenger will be displayed.
feature. Refer to the 9 Over head Console-Customer Pro- grammable Features. 9 The mode will also be shown in the display and will change as r equired during automatic operation. NOTE: The system can be put into recir culate mode without affecting A TC operation.
engine speed or power may be noticed when the com- pressor cycles. This is a normal occurrence since the compressor will cycle on and off to maintain comfort and improve fuel economy . Recirculate Button Press this button to r ecirculate the air inside the vehicle.
Bi-Level Air flows thr ough the outlets located in the instru- ment panel and those located on the floor . NOTE: There is a dif ference in temperatur e between the upper and lower outlets for added comfort. The warmer air goes to the floor outlets. This featur e gives improved comfort during sunny but cool conditions.
REAR OFF This turns the rear system off. The control will return to the front system display after approximately 5 seconds if no buttons are pushed while in one of the rear system displays.
The r ear compartment contr ol uses two rotary knobs: one for the temperature control and the other for the fan speed contr ol. The mode for the rear air conditioning and heating system is always controlled by the front control unit. Fan and temperatur e can be contr olled fr om the front control unit or the rear control unit.
NOTE: For best operation, make sure that ventilation grilles located in the rear storage area are not obstructed by stowed articles. Front Unit to Rear Unit Chart If the Front Control is selected Rear.
and adjust the temperature control and blower speed as necessary to maintain comfort. For high humidity condi- tions it may be necessary to remain in the Recirculation mode to maintain comfort. W indow Fogging W indows will fog on the inside when the humidity inside the vehicle is high.
Operating Tips Chart INSTRUMENT P ANEL AND CONTROLS 265 4 I n f o r m a t i o n P r o v i d e d b y :.
REAR WINDOW FEA TURES Rear Window Wiper/W asher A rotating switch located on the climate control panel turns the rear wiper On or Off. Pressing the rotating switch inwar d activates the rear window washer . Rotating the switch will enable one of five intermittent delay times for the rear wiper .
If the rear wiper is operating when the ignition is turned off, the wiper will automatically return to the “Park” position. When the vehicle is restarted, the wiper will resume operation. Rear Window Defrosting A push-button type switch is located in the climate control panel.
I n f o r m a t i o n P r o v i d e d b y :.
ST ARTING AND OPERA TING CONTENTS m Starting Procedures ..................... 2 7 3 ▫ Automatic T ransmission ................ 2 7 3 ▫ Normal Starting ...................... 2 7 3 m Engine Block Heater – If Equipped .......... 2 7 6 m Automatic T ransmission .
m Brake System .......................... 2 9 1 ▫ Four-Wheel Anti-Lock Brake System (ABS) . . . 291 m Power Steering ........................ 2 9 4 m Electronic Brake Control System ............ 2 9 5 ▫ ABS (Anti-Lock Brake System) ............ 2 9 5 ▫ BAS (Brake Assist System) .
m Supplemental T ire Pressure Information — If Equipped ............................ 3 2 2 m T ire Chains ........................... 3 2 2 m Snow T ires ........................... 3 2 3 m T ire Rotation Recommendations ............ 3 2 4 m T ire Pressure Monitor System (TPMS) — If Equipped .
▫ Cruising Range ....................... 3 4 2 ▫ Replacement Parts ..................... 3 4 2 ▫ Maintenance ......................... 3 4 2 m V ehicle Loading ........................ 3 4 3 ▫ Certification Label ..................... 3 4 3 ▫ Curb W eight .
ST ARTING PROCEDURES Before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts. W ARNING! Be sure to turn off the engine and remove the key from the ignition switch if you want to rest or sleep in your car .
T ip Start Feature Y our vehicle has a “T ip Start” starting system. W ith “T ip Start” the driver does not need to hold the key in the ’Start’ position until the vehicle starts, but can release the key (still in the ignition) and the vehicle will continue through the start cycle.
W ARNING! Do not attempt to push or tow your vehicle to get it started. V ehicles equipped with an automatic trans- mission cannot be started this way . Unburned fuel could enter the catalytic converter and once the engine has started, ignite and damage the converter and vehicle.
ENGINE BLOCK HEA TER – IF EQUIPPED The engine block heater warms engine coolant and permits quicker starts in cold weather . Connect the cor d to a standard 1 10-1 15 volt AC electrical outlet with a grounded, three wire extension cord. The 3.7L/4.7L engine block heater cord is located at the front of the engine compartment near the radiator cap.
“P” Park Supplements parking brake by locking the transmission. Engine can be started in this range. Never use Park while vehicle is in motion. Apply parking brake when leaving vehicle in this range. Always apply parking brake first, then place selector in Park position.
“R” Reverse Use this range only after the vehicle has come to a complete stop. “N” Neutral Shift to Neutral when vehicle is standing for prolonged periods with engine running. Engine may be started in this range. Set the parking brake if you must leave the vehicle.
Overdrive Operation The over drive automatic transmission contains an elec- tronically controlled fourth and fifth (if equipped) speed (Overdrive). The transmission will automatically shift from Drive.
The transmission will downshift from Over drive to Drive if the accelerator pedal is fully depressed at vehicle speeds above approximately 35 mph (56 km/h). When T o Use “TOW/HAUL” Mode When driving in hilly areas, towing a trailer , carrying a heavy load, etc.
light throttle. It engages at higher speeds under heavier acceleration. This may result in a slightly dif ferent feeling or response during normal operation in high gear . When the vehicle speed drops below a calibrated speed, or during acceleration, the clutch automatically and smoothly disengages.
Because four-wheel-drive provides improved traction, there is a tendency to exceed safe turning and stopping speeds. Do not go faster than road conditions permit. 4WD Normal Four-Wheel-Drive High Range - Employs inter- axle differ ential. Allows front and rear wheels to rotate at differ ent speeds.
LOCK and 4WD LOW positions on dry hard surfaced roads may cause increased tire wear and damage to the driveline components. The transfer case Neutral (N) position is selected by depressing the recessed button located on the lower left hand corner of the 4WD Control Switch.
equal for the shift to take place. Shifting while only the front or r ear wheels are spinning can cause damage to the transfer case. When operating your vehicle in 4WD LOW , the engine speed is appr oximately three times that of the 4WD or 4WD LOCK positions at a given road speed.
For additional information on the appr opriate use of each transfer case mode position see the following informa- tion: 4WD Normal Four-Wheel-Drive High Range - Employs inter- axle differ ential. Allows front and rear wheels to rotate at differ ent speeds.
Shifting Procedure - NV 244 Generation II T ransfer Case NOTE: The 4x4 system will not allow shifts between 4WD/ 4WD LOCK if the rear wheels are spinning (no traction). In this situation a position indicator light will flash and the original position indicator light will remain ON.
3. While still rolling, rotate the transfer case contr ol switch to the desired position. 4. After the position indicator light has stopped flashing, shift the transmission back into gear . Alternate Procedure 1. Bring the vehicle to complete stop. 2.
3. Replace tires when tread wear indicators first become visible. 4. Keep tires properly inflated. 5. Maintain sufficient distance between your vehicle and the car in front to avoid a collision in a sudden stop.
CAUTION! • Always check the depth of the standing water before driving through it. Never drive through standing water that is deeper than the bottom of the tire rims mounted on the vehicle. • Determine the condition of the road or the path that is under water and if there are any obstacles in the way before driving through the standing water .
P ARKING BRAKE The foot operated parking brake is positioned below the lower left corner of the instrument panel. T o release the parking brake, pull the parking brake release handle. Be sure the parking brake is firmly set when parked and the gear -shift lever is in P ARK position.
W ARNING! • Always fully apply the parking brake when leav- ing your vehicle, or vehicle may roll and cause damage or injury . Also be certain to leave an automatic transmission in Park. Failure to do so may cause the vehicle to roll and cause damage or injury .
surfaces. All vehicle wheels and tires must be the same size and type and tires must be properly inflated to produce accurate signals for the computer . W ARNING! Significant over or under inflation of tires, or mixing sizes of tires or wheels on the vehicle can lead to loss of braking effectiveness.
W ARNING! Anti-Lock Brake Systems contain sophisticated elec- tronic equipment. It may be susceptible to interfer- ence caused by improperly installed or high output radio transmitting equipment. This interference can cause possible loss of anti-lock braking capability .
When you are in a severe braking condition involving use of the Anti-lock Brake system, you will experience some pedal drop as the vehicle comes to a stop. This is the result of the system reverting to the base brake system. Engagement of the Anti-lock Brake System may be accompanied by a pulsing sensation.
W ARNING! Continued operation with reduced power steering assist could pose a safety risk to yourself and others. Service should be obtained as soon as possible. CAUTION! Prolonged operation of the steering system at the end of the steering wheel travel will increase the steering fluid temperature and should be avoided when pos- sible.
W ARNING! • Anti-lock system (ABS) cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase braking or steering efficiency beyond that afforded by the condition of the vehicle brakes and tires or the traction afforded.
applies optimum pr essure to the brakes in emer gency braking conditions. This can help reduce braking dis- tances. The BAS complements the antilock brake system (ABS). Applying the brakes very quickly results in the best BAS assistance. T o receive the benefit of the system, you must apply continuous braking pr essure during the stopping sequence.
TCS (T raction Control System) This system monitors the amount of wheel spin of each of the driven wheels. If wheel spin is detected, brake pressur e is applied to the slipping wheel(s) and engine power is reduced to provide enhanced acceleration and stability .
W ARNING! Many factors, such as vehicle loading, road condi- tions and driving conditions, influence the chance that wheel lift or rollover may occur . • ERM can not prevent all wheel lift or rollovers, especially those that involve leaving the roadway or striking objects or other vehicles.
• Understeer - when the vehicle is turning less than appropriate for the steering wheel position. ESP/TCS Indicator Light The 9 ESP/TCS Indicator Light 9 starts to flash as soon as the tir es lose traction and the TCS or ESP system becomes active.
4WD/4WD LOCK or 2WD Models ON This is the normal operating mode for ESP in 4WD LOCK and in 2WD vehicles. Whenever the vehicle is started or the transfer case (if equipped) is shifted from 4WD LOW or neutral back to 4WD LOCK, the ESP system will be in this mode.
mode by pressing the ESP Contr ol Switch. Once the situation r equiring ESP to be switched to the “Partial Of f” mode is overcome, turn ESP on by momentarily depress- ing the “ESP Control Switch”. This may be done with the vehicle is in motion.
W ARNING! In the Partial Of f mode, the engine torque reduction and stability features are desensitized. Therefore, the enhanced vehicle stability offered by ESP is unavailable. ESP/BAS W arning Lamp and ESP/TCS Indicator Light The malfunction indicator for the ESP is combined with the BAS indicator .
TSC (T railer Sway Control) TSC uses sensors in the vehicle to recognize a swaying trailer and will take the appropriate actions to attempt to stop the sway . The system will reduce engine power and apply individual brakes that will counter act the sway of the trailer .
TIRE SAFETY INFORMA TION Tire Markings NOTE: • P (Passenger)-Metric tire sizing is based on U.S. design standards. P-Metric tires have the letter “P” molded into the sidewall pr eceding the size designation. Ex- ample: P215/65R15 95H. • European Metric tire sizing is based on European design standards.
T ire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standards 9 ....blank.... 9 = Passenger car tire based on European design standards LT = Light T ruck tire based on U.
EXAMPLE: Service Description: 95 = Load Index —A numerical code associated with the maximum load a tire can carry . H = Speed Symbol —A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions.
Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire; however , the date code may only be on one side. T ires with white sidewalls will have the full TIN including date code located on the white sidewall side of the tire.
Tire Loading and Tire Pressure T ire Placard Location NOTE: The proper cold tire inflation pressure is listed on either the face of the driver’s door or the driver’s side “B” pillar .
Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. Y ou will not exceed the tire’s load carrying capacity if you adhere to the loadi.
4. The resulting figure equals the available amount of cargo and luggage load capacity . For example, if “XXX” amount equals 1400 lbs. and there will be five 150 lb. passengers in your vehicle, the amount of available cargo and luggage load capacity is 650 lbs.
312 ST ARTING AND OPERA TING I n f o r m a t i o n P r o v i d e d b y :.
W ARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, af fect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle.
2. Economy— Improper inflation pressur es can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will r educe tr ead life resulting in a need for earlier tire replacement. Under inflation, also increases tire r olling resistance and results in higher fuel consump- tion.
check tire pressure. Do not make a visual judgement when determining pr oper inflation. Radial tir es may look properly inflated even when they are under inflated. CAUTION! After inspecting or adjusting the tire pressure, al- ways reinstall the valve stem cap (if equipped).
T ire Pressures for High Speed Operation The manufacturer advocates driving at safe speeds within posted speed limits. Where speed limits or condi- tions are such that the vehicle can be driven at high speeds, maintaining correct tire inflation pressure is very important.
Compact Spare Tire — If Equipped The compact spare is for temporary emer gency use with radial tir es. It is engineered to be used on your style vehicle only . Since this tire has limited tread life, the original tire should be repaired (or replaced) and rein- stalled at the first opportunity .
original equipped tir e on the front or rear axle of your vehicle, but it is not. Installation of this limited use spare tire affects vehicle handling. Since it is not the same tir e, replace (or repair) the original tire and reinstall on the vehicle at the first opportunity .
T read Wear Indicators T read wear indicators are in the original equipment tir es to help you in determining when your tires should be replaced. These indicators are molded into the bottom of the tread grooves. They will appear as bands when the tr ead depth becomes 1/16 inch (2 mm).
W ARNING! T ires and spare tire should be replaced after six years, regardless of the remaining tread. Failure to follow this warning can result in sudden tire failure. Y ou could lose control and have an accident resulting in serious injury or death.
W ARNING! • Do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change suspen- sion dimensions and performance characteristics, resulting in changes to steering, handling, and brak- ing of your vehicle.
Improper alignment will not cause vehicle vibration. V ibration may be a result of tire and wheel out-of- balance. Proper balancing will reduce vibration and avoid tire cupping and spotty wear .
These cautions apply to all chain traction devices, includ- ing link and cable (radial) chains. T ire chain use is permitted only on the r ear tir es of your truck. NOTE: The use of class “S” chains is permitted on your vehicle with P245/70R17 tires.
TIRE ROT A TION RECOMMENDA TIONS T ires on the front and rear axles of vehicles operate at differ ent loads and perform different steering, driving, and braking functions. For these reasons, they wear at unequal rates and tend to develop irregular wear pat- terns.
TIRE PRESSURE MONITOR SYSTEM (TPMS) — IF EQUIPPED The T ire Pressure Monitoring System (TPMS) will warn the driver of a low tire pressur e based on the vehicle recommended cold placard pressure (the placard is lo- cated on the drivers side B-pillar).
For example, your vehicle has a recommended cold (parked for more than 3 hours) placard of 33 (227 kPa). If the ambient temperatur e is 68°F (20°C) and the measured tire pressure is 28 psi (193 kPa), a temperature drop to 20°F (-7°C) will decrease the tire pressur e to approxi- mately 24 psi (165 kPa).
NOTE: • The TPMS is not intended to replace normal tire care and maintenance, or to provide warning of a tire failure or condition. • The TPMS should not be used as a tire pressure gauge while adjusting your tire pressure. • Driving on a significantly under-inflated tire causes the tire to overheat and can lead to tire failure.
• T ire Pressur e Monitoring T elltale Lamp The T ir e Pressure Monitoring T elltale Lamp will illuminate in the instrument cluster , and an au- dible chime will be activated when one or more of the four active road tire pressur es are low .
limit, upon the next ignition key cycle, a chime will sound and the TPM T elltale Light will still turn ON due to the low tire. 3. However , after driving the vehicle for up to 10 min- utes above 15 mph (25 km/h), the TPM T elltale Light will flash on and off for 75 seconds and then remain on solid.
• Y ellow T ir e Pressur e Monitoring T elltale Light. T ire Pressure Monitoring Low Pressure W arnings The T ir e Pressure Monitoring T elltale Lamp will illumi- nate in the instrument cluster , and an audible chime will be activated when one or mor e of the four active road tire pressur es are low .
affects radio wave signals. 3) Lots of snow or ice around the wheels or wheel housings. 4) Using tire chains on the vehicle. 5) Using wheels/tires not equipped with TPM sensors. NOTE: Y our vehicle is equipped with a non-matching full size spare wheel and tire assembly .
The vehicle may need to be driven for up to 10 minutes above 15 mph (25 km/h) in or der for the TPMS to receive this information. General Information This device complies with part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following conditions: • This device may not cause harmful interference.
premium gasoline will not provide a benefit over high quality regular and mid-grade gasolines, and in some circumstances may result in poorer performance. Light spark knock at low engine speeds is not harmful to your engine. However , continued heavy spark knock at high speeds can cause damage and immediate service is requir ed.
CAUTION! DO NOT use gasoline containing Methanol or E85 Ethanol. Use of these blends may result in starting and driveability problems and may damage critical fuel system components. NOTE: 4.7L Engine — If Equipped , is now rated for E85 Ethanol use.
Materials Added T o Fuel All gasolines sold in the United States are required to contain effective detergent additives. Use of additional detergents or other additives is not needed under normal conditions and would result in unnecessary cost. There- fore, you should not have to add anything to the fuel.
NOTE: Intentional tampering with emissions control sys- tems can r esult in civil penalties being assessed against you. Carbon Monoxide W arnings W ARNING! Carbon monoxide (CO) in exhaust gases is deadly . Follow the precautions below to prevent carbon monoxide poisoning: • Do not inhale exhaust gases.
CAUTION! A poorly fitting gas cap may cause the Malfunction Indicator Light to turn on. CAUTION! T o avoid fuel spillage and overfilling, do not “top off” the fuel tank after filling. NOTE: When the fuel nozzle “clicks” or shuts off, the fuel tank is full.
W ARNING! A fire may result if gasoline is pumped into a portable container that is inside of a vehicle. Y ou could be burned. Always place gas containers on the ground while filling.
FLEXIBLE FUEL — IF EQUIPPED E-85 General Information The information in this section is for Flexible Fuel ve- hicles only . These vehicles can be identified by the unique fuel filler door label that states Ethanol (E-85) or Un- leaded Gasoline Only .
CAUTION! Only vehicles with the E-85 fuel filler cap (gas cap) can operate on E-85. ETHANOL FUEL (E-85) E-85 is a mixtur e of appr oximately 85% fuel ethanol and 15% unleaded gasoline. W ARNING! Ethanol vapors are extremely flammable and could cause serious personal injury .
For best results, a refueling pattern that alternates be- tween E-85 and unleaded gasoline should be avoided. When you do switch fuels, it is recommended that • you do not switch when the fuel gauge.
increase in the time it takes for your engine to start, and a deterioration in drivability (sags and/or hesitations) until the engine is fully warmed up. Cruising Range Because E-85 fuel contains less energy per gallon than gasoline, you will experience an increase in fuel con- sumption.
VEHICLE LOADING Certification Label As required by National Highway T raffic Safety Admin- istration Regulations, your vehicle has a certification label affixed to the driver’s side door .
Gross Axle W eight Rating (GA WR) The GA WR is the maximum permissible load on the front and rear axles. The load must be distributed in the cargo area so that the GA WR of each axle is not exceeded. Each axle GA WR is determined by the component in the system with the lowest load carrying capacity (axle, springs, tires, or wheels).
then be determined separately to be sure that the load is properly distributed over fr ont and r ear axle. W eighing the vehicle may show that the GA WR of either the front or rear axles has been exceeded but the total load is within the specified GVWR.
after the vehicle has been weighed both in its ( curb weight ( condition, and in its ( loaded and ready for operation ( condition. Gross V ehicle W eight Rating (GVWR) 6500 LBS. TRAILER TOWING In this section you will find safety tips and information on limits to the type of towing you can reasonably do with your vehicle.
Gross T railer W eight (GTW) The gr oss trailer weight (GTW) is the weight of the trailer plus the weight of all cargo, consumables and equipment (permanent or temporary) loaded in or on the trailer in its 9 loaded and ready for operation 9 condition.
Frontal Area The maximum height and maximum width of the front of a trailer . TSC (T railer Sway Control) – If Equipped • T railer Sway Control – Electronic TSC uses sensors in the vehicle to recognize a swaying trailer and will take the appropriate actions to attempt to stop the sway .
W eight-Distributing Hitch A weight-distributing system works by applying lever- age through spring (load) bars. They ar e typically used for heavier loads, to distribute trailer tongue weight to the tow vehicle’s front axle and the trailer axle(s).
W eight Distributing Hitch System Improper Adjustment of W eight Distributing System 350 ST ARTING AND OPERA TING I n f o r m a t i o n P r o v i d e d b y :.
Fifth-Wheel Hitch A special high platform with a coupling that mounts over the rear axle of the tow vehicle in the truck bed. Connects a vehicle and fifth-wheel trailer with a coupling king pin. Gooseneck Hitch The gooseneck hitch employs a pivoted coupling arm which attaches to a ball mounted in the bed of a pickup truck.
T railer T owing Weights (Maximum T railer Weight Ratings) NOTE: For additional trailer towing information (maxi- mum trailer weight ratings) refer to the following website addresses: • http:// www .dodge.com/towing . • http:// www .dodge.ca (Canada).
• The weight of any other type of cargo or equipment put in or on your vehicle. • The weight of the driver and all passengers. NOTE: Remember that everything put into or on the trailer adds to the load on your vehicle.
W ARNING! Improper towing can lead to an injury accident. Follow these guidelines to make your trailer towing as safe as possible: Make certain that the load is secured in the trailer and will not shift during travel. When trailering cargo that is not fully secured, dynamic load shifts can occur that may be dif ficult for the driver to control.
2. GTW 3. GA WR 4. T ongue weight rating for the trailer hitch utilized (This requirement may limit the ability to always achieve the 10% to 15% range of tongue weight as a percentage of total trailer weight). T owing Requirements — T ires − Do not attempt to tow a trailer while using a compact spare tire.
actuated brakes. When towing a trailer equipped with a hydraulic surge actuated brake system, an electronic brake controller is not required. − T railer brakes are recommended for trailers over 1,000 lbs (454 kg) and requir ed for trailers in excess of 2,000 lbs (907 kg).
NOTE: Do not cut or splice wiring into the vehicles wiring harness. The electrical connections are all complete to the vehicle but you must mate the harness to a trailer connector . Refer to the following illustrations. T owing Tips Before setting out on a trip, practice turning, stopping and backing the trailer in an area away from heavy traffic.
If using a manual transmission vehicle for trailer towing, all starts must be in FIRST gear to avoid excessive clutch slippage. T owing T ips — Automatic T ransmission The “D” range can be selected when towing. However , if frequent shifting occurs while in this range, the “TOW HAUL” feature should be selected.
T owing T ips — Cooling System T o r educe potential for engine and transmission over- heating, take the following actions: − City Driving When stopped for short periods of time, put transmission in neutral and increase engine idle speed. − Highway Driving Reduce speed.
CAUTION! Using this vehicle for snowplow applications can cause damage to the vehicle. W ARNING! Attaching a snowplow to this vehicle could adversely affect performance of the airbag system in an acci- dent. Do not expect that the airbag will perform as described earlier in this manual RECREA TIONAL TOWING (BEHIND MOTORHOME, ETC.
W ARNING! Y ou or others could be injured if you leave the vehicle unattended with the transfer case in the Neutral (N) position without first fully engaging the parking brake.
3. T urn the ignition key to the ON position without starting the engine. 4. Depress brake pedal. 5. Shift automatic transmission to Neutral (N). 6. Using the point of a ballpoint pen or similar object, depress the recessed transfer case Neutral (N) button for 4 seconds.
CAUTION! Damage to the transmission may occur if the trans- mission is shifted into Park (P) with the transfer case in Neutral (N) and the engine RUNNING.
the 1 second time, then all of the position indicator lights will flash continuously until all requir ements are met or until the Neutral (N) button is released. NOTE: The ignition key must be ON for a shift to take place and for the position indicator lights to be operable.
WHA T T O DO IN EMERGENCIES CONTENTS m Hazard W arning Flasher .................. 3 6 6 m Jacking And T ire Changing ................ 3 6 7 ▫ Jack Location ........................ 3 6 7 m Jacking Instructions ..................... 3 6 8 ▫ Removing The Spare T ire .
HAZARD W ARNING FLASHER The flasher switch is on the top of the steering column, just behind the steering wheel. Press the flasher switch and all front and rear dir ectional signals will flash intermittently . Press the switch a second time to turn off the emergency flashers.
JACKING AND TIRE CHANGING W ARNING! • Being under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. Y ou could be crushed. Never put any part of your body under a vehicle that is on a jack. Never start or run the engine while the vehicle is on a jack.
JACKING INSTRUCTIONS Removing The Spare Tire The spare tire on your vehicle is located underneath the vehicle in the rear . 368 WHA T TO DO IN EMERGENCIES I n f o r m a t i o n P r o v i d e d b y :.
Remove the spar e tire befor e attempting to jack the tr uck. 1. Remove the rubber plug fr om the floor in the cargo area. 2. Engage the jack wrench extension to the spar e tire winch through the hole in the floor . 3. T urn the wrench counterclockwise to lower the spare tire.
Tire Changing Procedure W ARNING! Getting under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. Y ou could be crushed. Never get any part of your body under a vehicle that is on a jack. Never start or run the engine while the vehicle is on a jack.
• Block both the front and rear of the wheel diagonally oppo- site the jacking position. For example, if the right front wheel is being changed, block the left rear wheel. • Passengers should not remain in the vehicle when the vehicle is being jacked.
When changing a r ear wheel, assemble the jack drive tube to the jack and connect the drive tube to the extension tube. Place the jack under the axle as close to the tire as posssible with the drive tubes extending to the rear . Connect the jack tube extension and wheel wrench.
W ARNING! Raising the vehicle higher than necessary can make the vehicle unstable and cause an accident. It could slip off the jack and hurt someone near it. Raise the vehicle only enough to remove the tire. 5. Remove the wheel nuts and pull the wheel off.
W ARNING! Carefully follow these tire changing warnings to help prevent personal injury or damage to your vehicle: • Always park on a firm, level surface as far from the edge of the roadway as possible before raising the vehicle. • Block the wheel diagonally opposite the wheel to be raised.
JUMP ST ARTING PROCEDURES W ARNING! • Battery fluid is a corrosive acid solution; do not allow battery fluid to contact eyes, skin or cloth- ing. Don’t lean over battery when attaching clamps or allow the clamps to touch each other . If acid splashes in eyes or on skin, flush the contami- nated area immediately with large quantities of water .
4. Connect one end of a jumper cable to the positive terminal of the booster battery . Connect the other end of the same cable to the positive terminal of the discharged battery . W ARNING! Do not permit vehicles to touch each other as this could establish a ground connection and personal injury could result.
W ARNING! Any procedure other than above could result in: 1. Personal injury caused by electrolyte squirting out the battery vent; 2. Personal injury or property damage due to battery explosion; 3. Damage to charging system of booster vehicle or of immobilized vehicle.
W ARNING! Chains are not recommended for freeing a stuck vehicle. Chains may break, causing serious injury or death. W ARNING! Stand clear of vehicles when pulling with tow hooks. T ow straps and chains may break, causing serious injury . CAUTION! T ow hooks are for emergency use only , to rescue a vehicle stranded off road.
Four-Wheel Drive V ehicles The manufacturer recommends towing with all wheels OFF the ground. Acceptable methods are to tow the vehicle on a flatbed or with one end of the vehicle raised and the opposite end on a towing dolly .
I n f o r m a t i o n P r o v i d e d b y :.
MAINT AINING YOUR VEHICLE CONTENTS m Engine Compartment 3.7L V6 .............. 3 8 4 m Engine Compartment 4.7L V -8 .............. 3 8 5 m Engine Compartment 5.7L HEMI V -8 ......... 3 8 6 m Onboard Diagnostic System — OBD II ........ 3 8 7 ▫ Loose Fuel Filler Cap Message .
▫ Power Steering — Fluid Check ............ 3 9 9 ▫ Air Conditioner Maintenance ............. 3 9 9 ▫ Front Suspension Ball Joints .............. 4 0 0 ▫ Drive Shaft Constant V elocity Joints ........ 4 0 1 ▫ Body Lubrication .............
▫ Center High-Mounted Stoplight ........... 4 3 7 ▫ Fog Lights .......................... 4 3 8 m Fluids And Capacities ................... 4 3 9 m Fluids, Lubricants And Genuine Parts ........ 4 4 0 ▫ Engine ............................. 4 4 0 ▫ Chassis .
ENGINE COMP ARTMENT 3.7L V6 384 MAINT AINING YOUR VEHICLE I n f o r m a t i o n P r o v i d e d b y :.
ENGINE COMP ARTMENT 4.7L V -8 MAINT AINING YOUR VEHICLE 385 7 I n f o r m a t i o n P r o v i d e d b y :.
ENGINE COMP ARTMENT 5.7L HEMI V -8 386 MAINT AINING YOUR VEHICLE I n f o r m a t i o n P r o v i d e d b y :.
ONBOARD DIAGNOSTIC SYSTEM — OBD II Y our vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission contr ol systems.
Loose Fuel Filler Cap Message After fuel is added, the vehicle diagnostic system can determine if the fuel filler cap is possibly loose, impr op- erly installed, or damaged. A loose fuel filler cap message will be displayed in the instrument cluster .
Y our vehicle has a simple ignition key actuated test which you can use prior to going to the test station. T o check if your vehicle’s OBD system is r eady , you must do the following: 1. Insert your ignition key into the ignition switch. 2. T urn the ignition to the ON position, but do not crank or start the engine.
vehicle serviced befor e going to the I/M station. The I/M station can fail your vehicle because the MIL symbol is on with the engine running. REPLACEMENT P ARTS Use of genuine Mopar t parts for normal/scheduled maintenance and repairs is highly recommended to in- sure the designed performance.
MAINTENANCE PROCEDURES The pages that follow contain the required maintenance services determined by the engineers who designed your vehicle. Besides the maintenance items for which there ar e fixed maintenance intervals, there are other items that should operate satisfactorily without periodic maintenance.
CAUTION! Overfilling or underfilling the crankcase will cause oil aeration or loss of oil pressure. This could damage your engine. Change Engine Oil Follow the Maintenance Schedule for recommended en- gine oil and filter change intervals.
Engine Oil Selection For best performance and maximum protection under all types of operating conditions, the manufactur e only recommends engine oils that are API certified and meet the r equirements of DaimlerChrysler Material Standard MS-6395.
Synthetic Engine Oils Y ou may use synthetic engine oils pr ovided the r ecom- mended oil quality requir ements are met, and the recom- mended maintenance intervals for oil and filter changes are followed.
belt tension can cause belt slippage and failure. Belts should be inspected for evidence of cuts, cracks, glazing, or frayed cords and replaced if there is indication of damage which could result in belt failure. Low generator belt tension can cause battery failur e.
Engine Fuel Filter A plugged fuel filter can cause stalling, limit the speed at which a vehicle can be driven or cause har d starting. Should an excessive amount of dirt accumulate in the fuel tank, frequent filter replacement may be necessary . Catalytic Converter The catalytic converter requir es the use of unleaded fuel only .
W ARNING! A hot exhaust system can start a fire if you park over materials that can burn. Such materials might be grass or leaves coming into contact with your exhaust system. Do not park or operate your vehicle in areas where your exhaust system can contact anything that can burn.
W ARNING! • Battery fluid is a corrosive acid solution and can burn or even blind you. Don’t allow battery fluid to contact your eyes, skin or clothing. Don’t lean over a battery when attaching clamps. If acid splashes in eyes or on skin, flush the area imme- diately with large amounts of water .
Power Steering — Fluid Check Checking the power steering fluid level at a defined service interval is not required. The fluid should only be checked if a leak is suspected, abnormal noises are apparent, and/or the system is not functioning as antici- pated.
W ARNING! • Use only refrigerants and compressor lubricants approved by the manufacturer for your air condi- tioning system. Some unapproved refrigerants are flammable and can explode, injuring you. Other unapproved refrigerants or lubricants can cause the system to fail, requiring costly repairs.
Drive Shaft Constant V elocity Joints All four wheel drive models are equipped with four constant velocity joints. Periodic lubrication of these joints is not required. However , the joint boot should be inspected for external leakage or damage periodically .
A void using the wiper blades to remove frost or ice from the windshield. Keep the blade rubber out of contact with petroleum products such as engine oil, gasoline, etc. Windshield and Rear Window Washers The fluid reservoir for the windshield washers and the rear window washer is shared.
damaged, have a competent mechanic inspect the com- plete exhaust system and adjacent body areas for broken, damaged, deteriorated, or mispositioned parts. Open seams or loose connections could permit exhaust fumes to seep into the passenger compartment.
clean by gently spraying water from a gar den hose vertically down the face of the condenser and radiator . Check the coolant recovery bottle tubing for brittle rub- ber , cracking, tears, cuts and tightness of the connection at the bottle and radiator .
CAUTION! • Mixing of coolants other than specified HOA T engine coolants may result in engine damage and may decrease corrosion protection. If a non-HOA T coolant is introduced into the cooling system in an emergency , it should be replaced with the speci- fied coolant as soon as possible.
• Use only high purity water such as distilled or deion- ized water when mixing the water/engine coolant solution. The use of lower quality water will r educe the amount of corr osion protection in the engine cooling system.
Disposal of Used Engine Coolant Used ethylene glycol based engine coolant is a regulated substance r equiring proper disposal. Check with your local authorities to determine the disposal rules for your community .
• Do not overfill the coolant recovery bottle. • Check coolant freeze point in the radiator and in the coolant recovery bottle. If antifreeze needs to be added, contents of coolant recovery bottle must also be protected against freezing.
Emission Related Components Fuel System Hoses And V apor/V acuum Harnesses When the vehicle is serviced for scheduled maintenance, inspect surface of hoses and nylon tubing for evidence of heat and mechanical damage. Hard and brittle rubber , cracking, checking, tears, cuts, abrasions, and excessive swelling suggest deterioration of the rubber .
attempt to clean the PCV valve! Check ventilating hose for indication of damage or plugging with deposits. Replace if necessary . Brake System Power Disc Brakes (Front and Rear) Disc brakes do not r equire adjustment; however , several hard stops during the break-in period are recommended to seat the linings and wear off any foreign material.
Use only brake fluid that has been in a tightly closed container to avoid contamination from foreign matter or moisture. CAUTION! Do not allow a petroleum-base fluid to contaminate the brake fluid. Seal damage may result. Brake Hoses Inspection should be performed whenever the brake system is serviced or at intervals specified.
least 15 miles (24 km) of driving. At normal operating temperature the fluid cannot be held comfortably be- tween the fingertips. T o check the automatic transmission fluid level properly , the following procedur e must be used: 1. Operate the engine at idle speed and normal operating temperature.
CAUTION! Be aware that if the fluid temperature is below 50°F (10°C) it may not register on the dipstick. Do not add fluid until the temperature is elevated enough to produce an accurate reading.
CAUTION! Using a transmission fluid other than the manufac- turers recommended fluid may cause deterioration in transmission shift quality and/or torque converter shudder . Using a transmission fluid other than the manufacturers recommended fluid will result in more frequent fluid and filter changes.
NOTE: The presence of water in the gear lubricant will result in corrosion and possible failure of differential components. Operation of the vehicle in water , as may be encountered in some off-highway types of service, will requir e draining and refilling the axle to avoid damage.
• Insects, tree sap and tar . • Salt in the air near seacoast localities. • Atmospheric fallout/industrial pollutants. W ashing • W ash your vehicle regularly . Always wash your ve- hicle in the shade using a mild car wash soap, and rinse the panels completely with clear water .
• If your vehicle is damaged due to an accident or similar cause which destroys the paint and pr otective coating have your vehicle r epaired as soon as possible. The cost of such repairs is considered the responsibil- ity of the owner . • If you carry special cargo such as chemicals, fertilizers, de-icer salt, etc.
• For grease stains, apply Mopar t Multi-purpose cleaner to a clean, damp cloth and remove stain. Use a fresh, damp towel to remove soap residue. • Do not use any solvents or protectants on Y es Essen- tials products. Interior Care Use Mopar t Fabric Cleaner to clean fabric upholstery and carpeting.
T o minimize the possibility of scratching the lenses and reducing light output, avoid wiping with a dry cloth. T o remove road dirt, wash with a mild soap solution fol- lowed by rinsing. Do not use abrasive cleaning components, solvents, steel wool or other aggressive material to clean the lenses.
Replace the belts if they appear frayed or worn or if the buckles do not work properly . FUSE BLOCK CAUTION! When replacing a blown fuse, it is important to use only a fuse having the correct amperage rating. The use of a fuse with a rating other than indicated may result in a dangerous electrical system overload.
Fuses (Interior) The fuse block contains blade-type mini-fuses, relays, and circuit breakers for high-current circuits. It is located in the left kick panel.
Cavity Mini Fuse/Color Description F1 15 Amp Blue Instrument Clus- ter Battery Feed F 2 10 Amp Red Spare F3 10 Amp Red Ignition Run/ Start for Next Generation Con- troller (NGC), Integrated Power Modu.
Cavity Mini Fuse/Color Description F10 10 Amp Red Spar e F1 1 10 Amp Red Heated Mirrors F12 20 Amp Y ellow Cluster Battery Feed F13 10 Amp Red Ignition Run HV AC Module/ Heated Rear Glass (EBL) Re- la.
Fuses (Power Distribution Center) Y our vehicle is equipped with an electrical power distri- bution center located in the left side of the engine compartment.
Cavity Cartridge Fuse / Relay Mini Fuse Description 7 40 Amp Green Blower Motor Relay Feed 8 40 Amp Green JB Feed Acc Delay 9 Spare 10 30 Amp Pink ASD 1 1 40 Amp Green Power Liftgate ( If Equipped) 12.
Cavity Cartridge Fuse / Relay Mini Fuse Description 23 20 Amp Y ellow T railer T ow 24 15 Amp Blue A/C Clutch 25 15 Amp Blue Stop Lamp Switch 26 Spare 27 20 Amp Y ellow Run/Start Relay Feed 28 Spare 2.
Fuses (Integrated Power Module) An integrated Power Module is located in the left side of the engine compartment. This center contains cartridge fuses, mini fuses and relays.
Cavity Cartridge Fuse / Relay Mini Fuse Description 10 10 Amp Red Rt Park Lamps 1 1 Relay Radiator Fan Hi Rly 12 20 Amp Y ellow Front Control Mod- ule (FCM) Batt #4 13 20 Amp Y ellow Front Control Mod.
Cavity Cartridge Fuse / Relay Mini Fuse Description 26 Relay Adjustable Pedal Rly 27 30 Amp Green Ignition Off Draw (IOD) #1 28 30 Amp Green Ignition Off Draw (IOD) #2 29 Spare 30 Spare VEHICLE STORAG.
REPLACEMENT LIGHT BULBS LIGHT BULBS — Interior Bulb No. Dome Light .................... N o t S e r viceable Liftgate Lamp ........................... 5 6 7 Overhead Console Lights ........... N o t S e r viceable Reading Light ................... N o t S e r viceable V isor V anity Lights .
2. Remove one nut that attaches the headlight to the inner fender panel. Access to the nut is possible by opening the fender panel access door which is located in the wheel liner . 3. Grasp the headlight and pull firmly to disengage the headlight from the fender panel.
Rear Side Marker , T ail Lights, T urn Signals And Backup Lights — Replacement 1. Remove the two push-pins from the tail light housing. 432 MAINT AINING YOUR VEHICLE I n f o r m a t i o n P r o v i .
2. Rotate the light to the outboard side of the vehicle and remove. 3. Unlock and remove electrical connector . MAINT AINING YOUR VEHICLE 433 7 I n f o r m a t i o n P r o v i d e d b y :.
4. Remove the three screws holding the bulb strip to the back of the tail lamp. 5. Remove the bulb strip from the tail light lens. 434 MAINT AINING YOUR VEHICLE I n f o r m a t i o n P r o v i d e d b.
6. Remove bulbs from bulb strip by pulling the bulb straight out. MAINT AINING YOUR VEHICLE 435 7 I n f o r m a t i o n P r o v i d e d b y :.
License Lights 1. Remove the two screws securing the lens to the liftgate. 2. Rotate the socket 1/4 turn counterclockwise. 3. Pull bulb from socket. 436 MAINT AINING YOUR VEHICLE I n f o r m a t i o n.
Center High-Mounted Stoplight 1. Remove two screws securing stoplight housing assem- bly to the liftgate. 2. T urn socket 1/4 counterclockwise and free from hous- ing.
Fog Lights T o replace the left foglamp bulb: 1. Remove the three wheel liner screws. 2. Remove the remove the far left air dam screw at the bottom of the fascia. 3. Peel back the liner and access the foglamp. 4. Rotate the socket and connector 1/4 turn counter- clockwise and pull straight reward to disengage fr om the lamp.
FLUIDS AND CAP ACITIES U.S. Metric Fuel 3.7L/4.7L, 87 Octane 27 Gal. 102L 5.7L, 89 Octane 27 Gal 102L Engine Oil (with filter) 3.7L, SAE 5W -20, API Certified 5 Qt. 4.7L 4.7L, SAE 5W -20, API Certified 6 Qt. 5.7L 5.7L, SAE 5W -20, API Certified 7 Qt. 6.
FLUIDS, LUBRICANTS AND GENUINE P ARTS Engine Component Fluids, Lubricants and Genuine Parts Engine Coolant Mopar t Antifreeze/Coolant 5 Y ear/100,000 Mile Formula HOA T (Hybrid Or- ganic Additive T echnology) 3.7/4.7L/5.7L Engine Oil Use API Certified SAE 5W -20 Engine Oil, meeting the requirements of DaimlerChrysler Material Standard MS-6395.
Chassis Component Fluids, Lubricants and Genuine Parts. Automatic T ransmission Mopar t A TF+4, Automatic T ransmission Fluid. T ransfer Case Mopar t A TF+4, Automatic T ransmission Fluid. Front Axle SAE 75W -90 Multipurpose T ype, GL-5 Gear Lubricant or equivalent.
I n f o r m a t i o n P r o v i d e d b y :.
MAINTENANCE SCHEDULES CONTENTS m Emission Control System Maintenance ........ 4 4 4 m Maintenance Schedule ................... 4 4 4 ▫ Required Maintenance Intervals .
EMISSION CONTROL SYSTEM MAINTENANCE The “Scheduled” maintenance services, listed in bold type on the following pages must be done at the times or mileages specified to assur e the continued proper func- tioning of the emission control system.
if it has been 6 months since your last oil change even if the oil change indicator message is NOT illumi- nated. • Change your engine oil more often if you drive your vehicle off-r oad for an extended period of time. • Under no circumstances should oil change intervals exceed 6,000 miles (10,000 km) or 6 months, whichever comes first.
Once a Month • Check tire pressur e and look for unusual wear or damage. • Inspect the battery and clean and tighten the terminals as requir ed. • Check the fluid levels of coolant reservoir , brake master cylinder , power steering and transmission and add as needed.
Perform Maintenance Every (Where time and mileage are listed, follow the interval that occurs first.) Maintenance Items Miles Kilometers or Months Change the engine oil and engine oil filter . 6,000 10 000 6 Rotate T ires. 6,000 10 000 6 If using your vehicle for any of the following: Dusty or off-r oad conditions.
Perform Maintenance Every (Where time and mileage are listed, follow the interval that occurs first.) Maintenance Items Miles Kilometers or Months Replace the engine air cleaner filter . 30,000 50 000 30 Inspect the transfer case fluid. 30,000 50 000 30 Replace the top row of spark plugs on 4.
Perform Maintenance Every (Where time and mileage are listed, follow the interval that occurs first.) Maintenance Items Miles Kilometers or Months Change the manual transmission fluid if using your ve.
Perform Maintenance Every (Where time and mileage are listed, follow the interval that occurs first.) Maintenance Items Miles Kilometers or Months Drain and refill automatic transmission fluid and change main sump filter and spin-on cooler return filter (if equipped)(4.
IF YOU NEED CONSUMER ASSIST ANCE CONTENTS m Suggestions For Obtaining Service For Y our V ehicle .............................. 4 5 2 ▫ Prepare For The Appointment ............ 4 5 2 ▫ Prepare A List ........................ 4 5 2 ▫ Be Reasonable W ith Requests .
SUGGESTIONS FOR OBT AINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment If you’re having warranty work done, be sur e to have the right papers with you. T ake your warranty folder . All work to be performed may not be covered by the warranty , discuss additional charges with the service manager .
technicians, special tools, and the latest information to assure your vehicle is fixed corr ectly and in a timely manner . This is why you should always talk to your dealer’s service manager first.
Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) T o assist customers who have hearing difficulties, the manufacturer has installed special TDD (T elecommuni- cation Devices for the Deaf) equipment at its Customer Center .
W ARNING! Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
REPORTING SAFETY DEFECTS In the 50 United States and W ashington D.C.: If you believe that your vehicle has a defect, which could cause a crash or cause injury or death, you should immediately inform the National Highway T raffic Safety Administra- tion (NHTSA) in addition to notifying the manufacturer .
PUBLICA TION ORDER FORMS T o order the following manuals, you may use either the website or the phone numbers listed below . V isa, Mas- tercar d, American Express, and Discover orders are ac- cepted. If you prefer mailing your payment, please call for an order form.
Call T oll Free at: • 1–800–890–4038 (U.S.) • 1–800–387–1 143 (Canada) Or V isit us on the W orld Wide W eb at: • www .techauthority .
on specified government test surfaces of asphalt and concrete. A tire marked C may have poor traction perfor- mance. W ARNING! The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics.
I n f o r m a t i o n P r o v i d e d b y :.
INDEX 10 I n f o r m a t i o n P r o v i d e d b y :.
ABS (Anti-Lock Brake System) ............ 195,291 Adding Fuel ........................... 3 3 6 Adjustable Pedals ....................... 1 4 8 Air Cleaner , Engine (Engine Air Cleaner Filter) . . . 395 Air Conditioner Maintenance ............ 252,399 Air Conditioning .
Special Additives ...................... 4 1 3 T orque Converter ...................... 2 8 0 Axle Fluid ............................. 4 4 1 Axle Lubrication (Axle Fluid) ............... 4 1 4 Ball Joints ............................. 4 0 0 Battery ..
Oil (Engine) .......................... 3 9 3 Power Steering ........................ 3 9 9 Radiator (Coolant Pressur e) ............... 4 0 6 Car W ashes ............................ 4 1 6 Carbon Monoxide W arning ............... 75,336 Cargo Management System .
Adding Coolant (Antifreeze) .............. 4 0 5 Coolant Capacity ...................... 4 3 9 Coolant Level ...................... 403,407 Disposal of Used Coolant ................ 4 0 7 Drain, Flush, and Refill .................. 4 0 4 Inspection ..
Driving Through Flowing, Rising, or Shallow Standing W ater .............................. 2 8 8 DVD Player (V ideo Entertainment System) ...... 2 4 4 E-85 Fuel ............................. 3 3 9 Electric Remote Mirrors .................... 8 5 Electrical Power Outlets .
O i l ........................... 391,439,440 Oil Filler Cap ................. 384,385,386,393 Oil Selection ....................... 393,439 Oil Synthetic ......................... 3 9 4 Starting ............................. 2 7 3 T emperature Gauge .
Engine Oil ........................... 3 9 1 Power Steering ........................ 3 9 9 T ransfer Case ......................... 4 1 4 Fluids, Lubricants and Genuine Parts .......... 4 4 0 Fog Lights .......................... 141,438 Folding Rear Seat .
Gross V ehicle W eight Rating ................ 3 4 6 GVWR ............................ 343,346 Hands-Free Phone (UConnect™) ........ 87,236,237 Hard Drive (HDD) .................... 206,236 Hazard Driving Through Flowing, Rising, or Shallow Standing W ater .
Information Center , V ehicle ................. 1 5 9 Inside Rearview Mirror .................... 8 3 Instrument Cluster ....................... 1 9 3 Instrument Panel and Contr ols .............. 1 9 1 Instrument Panel Lens Cleaning ............. 4 1 9 Integrated Power Module (Fuses) .
Center Mounted Stop ................... 4 3 7 Courtesy/Reading ..................... 1 5 8 Cruise .............................. 2 0 3 Daytime Running ...................... 1 4 1 Dome .............................. 1 5 9 Electronic Stability Program (ESP) Indicator .
Lower Anchors and T ether for CHildren (LA TCH) .............................. 6 8 Lubrication, Body ....................... 4 0 1 Lug Nuts ............................. 3 7 3 Luggage Carrier ......................... 1 8 3 Lumbar Support ............
Oil Change Indicator , Reset ................. 1 9 7 Oil, Engine ......................... 391,440 Capacity ............................ 4 3 9 Change Interval ....................... 3 9 2 Dipstick ............................. 3 9 1 Disposal ........
Power Brakes .............................. 4 1 0 Distribution Center (Fuses) ....... 384,385,386,424 Door Locks ......................... 20,29 Lift Gate ............................. 3 6 Mirrors .............................. 8 5 Outlet (Auxiliary Electrical Outlet) .
Recreational T owing ...................... 3 6 0 Shifting into T ransfer Case Neutral (N) ....... 3 6 1 Shifting out of T ransfer Case Neutral (N) ..... 3 6 3 Reformulated Gasoline .................... 3 3 3 Refrigerant ............................ 4 0 0 Release, Hood .
Pretensioners .......................... 5 0 Reminder ............................ 1 9 4 Seats ................................. 1 1 4 Adjustment .......................... 1 1 4 Cleaning ............................ 4 1 7 Fold and T umble Rear ......
Spark Plugs ............................ 3 9 5 Speed Control (Cruise Control) .............. 1 4 9 Speedometer ........................... 1 9 5 Starting ............................... 2 7 3 Automatic T ransmission ................. 2 7 3 Emergency (Jump Starting) .
T i r e s ............................ 77,313,458 Aging (Life of T ires) .................... 3 1 9 Air Pressur e .......................... 3 1 3 Alignment ........................... 3 2 1 Chains .............................. 3 2 2 Changing .......
Cooling System T ips .................... 3 5 9 Hitches ............................. 3 5 1 Minimum Requirements ................. 3 5 3 T railer and T ongue W eight ................ 3 5 2 W iring .............................. 3 5 6 T railer T owing Guide .
V ehicle Identification Number (VIN) ............ 7 V ehicle Information Center ................. 1 5 9 V ehicle Loading ...................... 310,343 V ehicle Modifications/Alterations .............. 8 V ehicle Storage ......................... 4 2 9 V ideo Entertainment System (Rear Seat V ideo System) .
INTRODUCTION INTRODUCTION ROLLOVERWARNING HOW TO USETHIS MANUAL WARNINGSAND CAUTIONS VEHICLE IDENTIFICA TION NUMBER VEHICLE MODIFICA TIONS/ALTERA TIONS THINGS TO KNOW BEFORE ST ARTING YOUR VEHICLE A W.
デバイスDodge Durango (2008)の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Dodge Durango (2008)をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはDodge Durango (2008)の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Dodge Durango (2008)の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Dodge Durango (2008)で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Dodge Durango (2008)を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はDodge Durango (2008)の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Dodge Durango (2008)に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちDodge Durango (2008)デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
