DometicメーカーNDA1402の使用説明書/サービス説明書
ページ先へ移動 of 24
INST ALLA TION AND OPERATING INSTRUCTIONS REFRIGERA TOR FOR LP-GAS AND ELECTRIC OPERA TION NDA1402 USA Corporate Office CANADA Service Office 2320 Industrial Parkway Elkhart, IN 46515 Dometic Distribution Inc. Dometic Corporation 866 Langs Drive 2320 Industrial Pkwy .
3 NDA 1402 Rear view equipment used for text reference GENERAL INSTRUCTION This appliance is designed for storage of foods and storage of frozen foods and making ice. This appliance is certified under the latest edition of ANSI Z21.19•CSA 1.4 Refrigerators using gas fuel.
4 Refrigerator control panel FIG. 2 12 3 4 LEGEND 2-W A Y Model Panel Controls: 1. Main Power ON/OFF key 2. AUTO/ST ORE key/ Combined energy mode selection and store key PM AUTO AC GAS 3. LED Display Panel FREEZER FRIDGE The LED panel displays preferably temperatures in the refrigera- tor and current modes of operation.
5 INST ALLA TION VENTILA TION The installation shall be made in such a manner as to separate the combustion system from the living space of the mobile home or recreational vehicle. Openings for air supply or for venting of combustion products shall have a minimum dimension of not less than 1/4 inch.
6 INST ALLING REFRIGERA TOR IN ENCLOSURE Securing the Refrigerator After the refrigerator is put in place, (ensuring a com- bustion seal at the front frame), the refrigerator is to be secured in the enclosure with six screws (not included).
7 Step 2: T wo screws inst alled in the top frame. Open the doors and fasten the refrigerator with two screws through the holes underneath the top decoration panel. See FIG . 7. TESTING LP GAS SAFETY SHUT OFF The gas safety shut off must be tested after the re- frigerator is connected to LP gas supply.
8 CERTIFIED INST ALLA TION Certified installations require one roof vent and one lower side vent. For “Certified V ent System Kit s” see p age 19 . For further information contact your dealer or distributor . METHODS OF INST ALLA TION The method of installation is shown in FIG .
9 OPERA TING INSTRUCTIONS IMPORTANCE OF LEVELING A REFRIGERATOR In an absorption refrigerator system, ammonia is lique- fied in the finned condenser coil at the top rear of the refrigerator.
10 ST ART UP INSTRUCTIONS 1. Press the main power ON/OFF key . If the real time clock has to be set the LED panel will show flashing horizon- tal bars ” -- -- “. Set real time clock 1. T o enter TIME MODE keep SET key pressed until figures flash on the LED p anel.
11 St atus message St atus message Message displayed Steady Alternating between display temperatures and message Defrosting is just now performed ”dE Fr” X Thermostat range setting indication ” x “ x is a figure 1-5 X Gas operation problem. (1) ”ch LP” X DC voltage too low to st art defrosting.
12 Manual defrost If desired this refrigerator can be set to defrost manual at any time. Usually a defrost cycle takes about 1 hour but is depending on the amount of frost and could therefore vary from time to time. 1. Before entering manual defrost mode, switch of f the refrigerator with the ON/OFF key .
13 HOW T O USE THE REFRIGERA T O R FOOD STORAGE COMP ARTMENT The food storage compartment is completely closed and unventilated, which is necessary to maintain the required low temperature for food storage. Consequently , foods having a strong odor or those that absorb odors easily should be covered.
14 ELECTRIC EQUIPMENT HEA TERS The heat necessary for the operation of an absorption cooling unit is supplied by an electric heater mounted in a pocket of the boiler system. This model is equipped with a series connected twin heater . T o replace the heater proceed as follows: 1.
15 ICE MAKER GENERAL INSTRUCTIONS AND OPERA TION 1. The refrigerator must be connected to 120 volts AC before the ice maker can operate. The water valve supplying the refrigerator must be turned on, and the ice level bail arm in the fully down position.
16 6. Connect compressed air onto the inlet fitting of the water solenoid valve. See FIG . 14. Apply AC power to the solenoid valve by forcing the ice maker mold assembly through several harvest cycles. Remove the plastic cover from the mold assembly .
17 D. Inspect the flue baf fle. It should be reasonably clean and free of soot. Heavy soot formation indicates im- proper functioning of the burner . The flue and burner both require cleaning in the following manner: 1. Unplug the refrigerator power cord from the 120 volt AC outlet.
18 3. REPLACING A HALOGEN LAMP TROUBLESHOOTING The Refrigerator Does Not Cool Properly A. Burner jet clogged. Clean. (See section Maintenance & Service, Item 2. Periodic Maintenance, Paragraph D. Item 1-13.) B. Check level of refrigerator . C. V enting problem.
19 CERTIFIED VENT SYSTEM KITS REFRIGERATOR KIT MODEL NO. COMPONENTS PART NO. NDA 1402 5A Roof Base 3103633.XXX* Roof Cover 3103634.XXX* Lower Side V ent 3109349.XXX* Power Vent Asm. 3108705.744** * Fill in “XXX” with color code numbers. For color codes, contact your supplier.
20 Number Instruction Note 00 — — 01 LED panel check All LED segments ON 02 Battery voltage check ”12” → in range between 8,5 - 18 V DC. “Lo” or “h l ” → out of range 03 Air temper.
21 Put a screwdriver into the slot of the shelf lock. Turn the screwdriver counterclockwise. Remove the shelf locks from the wire shelf. Slide the wire shelf to the lef t. The right-hand side of the shelf will come loose. Lower the right-hand side of the wire shelf and let the left-hand side slide out of the holes in the wall.
22 Fuse T ype of component 3A A, B, C, E, G , H, P , R 7.5A S , T 3A W , (Optional ice maker heat-kit) 7.5A X 5A Z FUSES Refer to wiring diagram. Fuses from left to right protect the following components.
23.
24 MO-FO 0513.
Patents pending U.S. 10/619,675 U.S. 10/620,177 U.S. 10/758,174 U.S. 10/758,175 U.S. 10/760,564 U.S. 10/760,565 This product is manufactured under license of U.
デバイスDometic NDA1402の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Dometic NDA1402をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはDometic NDA1402の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Dometic NDA1402の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Dometic NDA1402で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Dometic NDA1402を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はDometic NDA1402の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Dometic NDA1402に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちDometic NDA1402デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。