Dukaneメーカー8055の使用説明書/サービス説明書
ページ先へ移動 of 70
Liquid Crystal Projector Model 8055 USER'S MANU AL.
.
Thank you for purchasing this projector. • The information in this manual is subject to change without notice. • The manufacturer assumes no responsibility for any errors that may appear in this manual. • The reproduction, transmission or use of this document or contents is not permitted without express written authority.
Projector Features … … … … … … … … … … … … … … 3 Preparation … … … … … … … … … … … … … … … … … … … … 3 Part Names … … … … .
3 ● Ultra High Brightness Crisp, ultra-bright presentations is achieved by using a UHB (ultra high brightness) lamp and a highly efficient optical system. ● Whisper Mode Equipped Special mode is available for reducing projector noise to achieve quieter operation.
4 Strap Rivet Strap hole Part Names The Projector Zoom ring 15 Focus ring 15 Air filter cover (An air filter is inside.) 35 Elevator button 8 Elevator feet 8 Indicates the corresponding reference page Lens cap 14 Lens (The picture is projected from here.
5 AC inlet 11 CONTROL port 10 VIDEO port 10 AUDIO OUT port 10 AUDIO IN port (from a computer) 10 S-VIDEO port 10 COMPONENT VIDEO - Y 10 COMPONENT VIDEO - C B /P B 10 COMPONENT VIDEO - C R /P R 10 AUDI.
6 The Remote Control (STANDBY/ON) button prepares for turning the power on/off. VIDEO button toggles between the signal ports of VIDEO, S-VIDEO and COMPONENT VIDEO. MENU button opens/closes the menu. RGB button selects the input signal of RGB port. BLANK button blanks the screen temporarily.
7 Setting Up Arrangement WARNING • Install the projector in a suitable environment according to instructions of the “User’s Manual – Safety Guide” and this manual. • The power outlet should be close to the projector and easily accessible. Refer to the illustrations and tables below to determine the screen size and projection distance.
8 Adjusting The Projector's Elevator CAUTION • If you press the elevator buttons without holding the projector, the projector might crash down, overturn, smash your fingers and possibly result in malfunction.
9 Connecting Y our Devices WARNING • Incorrect connecting could result in fire or electrical shock. Whenever attempting to connect other devices to the projector, please thoroughly read the "User's Manual - Safety Guide", this manual and the manual of each device to be connected.
10 Please refer to the following for connecting your devices. See the rear of the projector. You can see the ports. A C I N L-AUDIO-R VIDEO S-VIDEO IN AUDIO OUT AUDIO IN Y COMPONENT VIDEO C B / P B C .
11 1 A C I N Connect the connector of the power cord to the AC inlet of the projector. 1 2 Firmly plug the power cord’s plug into the outlet. WARNING • Please use extra caution when connecting the power cord as incorrect or faulty connections may result in FIRE and/or ELECTRICAL SHOCK.
12 CAUTION Always handle the batteries with care and use them only as directed. Improper use may result in battery cracking or leakage, which could result in fire, injury and/or pollution of the surrounding environment. • Keep the battery away from children and pets.
13 Operating The Remote Control ATTENTION • Do not drop or otherwise expose the remote control to physical impact. • Do not get the remote control wet or place it on wet objects.
14 ST ANDBY/ON INPUT POWER LAMP TEMP MENU Power ON/OFF Tu r ning On The Power WARNING • When the power is ON, a strong light is emitted. Do not look into the lens or vents of the projector. • Turn the power on/off in right order. Please power on the projector before the connected devices.
15 VIDEO ASPECT GO VO LUME MAGNIFY HOME P AGE UP AU TO BLANK RGB SEARCH ON VIDEO ASPECT VO LUME MAGNIFY HOME P AGE UP AU TO BLANK RGB SEARCH ON Selecting An Input Signal 1 2 Use the zoom ring to adjust the screen size. 3 Use the focus ring to focus the picture.
16 Tu r ning Off The Power • Turn the power on/off in right order. Please power on the projector before the connected devices. Power off the projector after the connected devices.
17 Operating Adjusting The V olume T emporarily Muting The Sound 1 Press the VOLUME button. As illustrated on the right, a dialog will appear on the screen to aid you in adjusting the volume. 2 Use the / buttons to adjust the volume. Press the VOLUME button again to close the dialog and complete this operation.
18 Adjusting The Position 1 Press the POSITION button. As illustrated on the right, a dialog will appear on the screen to aid you in adjusting the position. 2 Use the ,,, buttons to adjust the position. When you want to initialize the position, press the RESET button during adjustment.
19 Using The Automatic Adjustment Feature Correcting Keystone Distortions PA GE DOWN END HOME P AGE UP OFF ON VIDEO ASPECT MUTE KEYSTONE FREEZE MENU POSITION ENTER ESC RESET VOLUME AU TO BLANK RGB SEA.
20 Using The Magnify Feature Freezing The Scr een 1 Press the MAGNIFY (ON) button. The projector enters MAGNIFY mode. 2 Press the POSITION button, then use the ,,, buttons to select the area to zoom. Press the POSITION button again to finalize the zoom area.
21 Signal Searching Selecting The Aspect Ratio 1 Press the SEARCH button. Cycle through input signals, displaying the images of retrieved signals. If no signal is found, returns to the signal that was selected before the search was begun. • May not function properly with some input signals.
22 This projector has the following menus: MAIN, PICTURE-1, PICTURE-2, INPUT, AUTO, SCREEN, OPTION. Each of these menus is operated using the same methods. The basic operations of these menus are as follows. 1 Press the MENU button. The menu display appears on the screen.
23 MAIN Menu With the MAIN menu, the items shown in the table below can be performed. Perform each operation in accordance with the instructions in the table below.
24 PICTURE - 1 Menu With the PICTURE - 1 menu, the items shown in the Table below can be performed. Perform each operation in accordance with the instructions in the table below.
25 Item Description MY MEMORY Load/Save a Setting: Selecting one from the following and then pressing the or the ENTER button performs each function. LOAD1 ⇔ LOAD2 ⇔ LOAD3 ⇔ LOAD4 ⇒ SAVE1 ⇔ SAVE2 ⇔ SAVE3 ⇔ SAVE4 • This projector has 4 memories called M1, M2, M3 and M4 for settings.
26 PICTURE - 2 Menu With the PICTURE - 2 menu, the items shown in the table below can be performed. Perform each operation in accordance with the instructions in the table below.
INPUT Menu With the INPUT menu, the items shown in the table below can be performed. Perform each operation in accordance with the instructions in the table below.
28 Item Description VIDEO NR Select a Noise Reduction Mode: HIGH ⇔ MIDDLE ⇔ LOW • This function performs only at a VIDEO input or a S-VIDEO input. At a VIDEO input of NTSC 3.58, this function performs only when the TURN OFF is selected under the 3D-YCS.
29 MENU MAIN PICTURE-1 PICTURE-2 INPUT AUT O SCREEN OPTION ADJUST POWER OFF SEARCH RESET 0 min TURN ON : SELECT AUTO Menu With the AUTO menu, the items shown in the table below can be performed. Perform each operation in accordance with the instructions in the table below.
30 SCREEN Menu With the SCREEN menu, the items shown in the table below can be performed. Perform each operation in accordance with the instructions in the table below.
31 OPTION Menu With the OPTION menu, the items shown in the table below can be performed. Perform each operation in accordance with the instructions in the table below.
32 You can use the remote control as a simplified mouse or keyboard. Operating The PC Screen CAUTION Mistaken use of the mouse/keyboard control could damage your equipment. • Only connect to a PC. • Before connecting, read the manuals of the device you will connect.
33 Lamp The projector uses a high-pressure mercury glass lamp. The lamp can break with a loud bang, or burn out, if jolted or scratched, handled while hot, or worn over time. Note that each lamp has a different lifetime, and some may burst or burn out soon after you start using them.
34 1 Turn off the projector, and unplug the power cord. Allow the lamp bulb to cool for at least 45 minutes. 6 Insert the new lamp, and tighten the 2 screws firmly to lock it in place. Slide the lamp cover into place until it locks into position. Slowly turn the projector so that the top is facing up.
35 Air Filter Caring For The Air Filter The air filter should be cleaned about every 100 hours. If the indicators or a message prompts you to clean the air filter (see the section “Related Messages” and “Regarding The Indicator Lamps”), clean the air filter as soon as possible.
36 Replacing The Air Filter Filter cover Air filter Release buttons Release buttons Turn off the projector, and unplug the power cord. 2 Contact your local dealer to prepare a new air filter. Tell the dealer your air filter type number. 4 Hold the release buttons of the air filter, while pulling down it.
37 Other Care WARNING • Please carefully read the “User’s Manual - Safety Guide”. • Before replacing the air filter, make sure the power switch is off and the power cable is not plugged in. ATTENTION • Do not use cleaners or chemicals other than those listed below, including benzene and paint thinner.
38 T roubleshooting Related Messages When the unit's power is ON, messages such as those shown below may be displayed. When any such message is displayed on the screen, please respond as described below.
39 Wipe the dust-detecting window by using a soft cloth. T roubleshooting (continued) Related Messages (continued) Message Description CLEAN THE AIR FILTER POWER OFF FIRST, THEN CLEAN THE AIR FILTER. AFTER CLEANING THE AIR FILTER, RESET THE FILTER TIMER.
40 ATTENTION • When the interior portion has become overheated, for safety purposes, the power source is automatically turned off, and the indicator lamps may also be turned off. In such a case, press the “ ○ ” (power OFF) side of the main power switch, and wait at least 45 minutes.
41 POWER indicator LAMP indicator TEMP indicator Description Lighting or blinking in red Turned off Blinking in red The cooling fan is not operating. Turn the power OFF and wait at least 20 minutes. After the unit has sufficiently cooled down, please make confirmation of the following item, and then resent the power to ON.
42 WARNING • Please carefully read the “User’s Manual - Safety Guide”. Never use the projector if abnormal operations such as smoke, strange odor, excessive sound, damaged casing or elements or cables, penetration of liquids or foreign matter, etc.
43 Phenomenon Cases not involving a machine defect, and Items to be confirmed Reference pages Pictures appear dark. The brightness setting and/or contrast setting has not been properly adjusted. Perform picture adjustments by changing the BRIGHT and/or CONTRAST settings, etc.
44 • This specifications are subject to change without notice. NOTE Item Specification Product name Liquid crystal projector Liquid crystal panel Panel size 1.4 cm (0.55 type) Drive system TFT active matrix Pixels 480,000 pixels (800 horizontal x 600 vertical) Lens Zoom lens F=1.
Projector User's Manual - Safety Guide 1 About The Symbols Various symbols are used in this manual, the user’s manual and on the product itself to ensure correct usage, to prevent danger to the user and others, and to prevent property damage. The meanings of these symbols are described below.
2 Safety Pr ecautions W ARNING Never use the projector if a problem should occur. Abnormal operations such as smoke, strange odor, no image, no sound, excessive sound, damaged casing or elements or cables, penetration of liquids or foreign matter, etc.
W ARNING Be cautious of High temperatures of the projector. High temperatures are generated when the lamp is lit. It could result in fire or burn. Use special caution in households where children are present. Do not touch about the lens, air fans and ventilation openings during use or immediately after use, to prevent a burn.
W ARNING Be careful in handling the light source lamp. The projector uses a high-pressure mercury glass lamp made of glass. The lamp can break with a loud bang, or burn out. When the bulb bursts, it is possible for shards of glass to fly into the lamp housing, and for gas containing mercury to escape from the projector’s vent holes.
5 Safety Pr ecautions (continued) CAUTION Be careful in moving the projector. Neglect could result in an injury or damage. • Do not move the projector during use. Before moving, disconnect the power cord and all external connections, and close the slide lens door or attach the lens cap.
6 Safety Pr ecautions (continued) NOTE Do not give the remote control any physical impact. A physical impact could cause damage or malfunction of the remote control. • Take care not to drop the remote control. • Do not place the projector or heavy objects on the remote control.
7 Safety Pr ecautions (continued) NOTE Avoid strong rays. Any strong ray (such as direct rays of the sun or room lighting) onto the remote control sensors could invalidate the remote control. Avoid radio interference. Any interfering radiation could cause disordered image or noises.
Lamp 8 The projector uses a high-pressure mercury glass lamp. The lamp can break with a loud bang, or burn out, if jolted or scratched, handled while hot, or worn over time. Note that each lamp has a different lifetime, and some may burst or burn out soon after you start using them.
9 Regulatory Notices FCC Statement Warning WARNING: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
.
1 In this section, the technical information about this projector is described. • The information in this manual is subject to change without notice.
.
3 Example Of Computer Signal Resolution H × × V fH (kHz) fV (Hz) Rating Signal mode Display mode 720 × 400 37.9 85.0 VESA TEXT Zoom in 640 × 480 31.5 59.9 VESA VGA (60Hz) Zoom in 640 × 480 35.0 66.7 Mac13"mode Zoom in 640 × 480 37.9 72.8 VESA VGA (72Hz) Zoom in 640 × 480 37.
4 Initial Set Signals The following signals are used for the initial settings. The signal timing of some computer models may be different. In such case, refer to adjust the V.
5 RS-232C Communication Connection T o The Mouse Control 19200bps, 8N1 1. Protocol Consist of header (7 bytes) + command data (6 bytes). 2. Header BE + EF + 03 + 06 + 00 + CRC_low + CRC_high CRC_low :.
6 RS-232C Communication (continued) Requesting projector status (Get command) (1) Send the request code Header + Command data (‘02H’+‘00H’+ type (2 bytes)+‘00H’+‘00H’) from the computer to the projector. (2) The projector returns the response code ‘1DH’+ data (2 bytes) to the computer.
7 Command Data Chart Names Operation type Header Command data CRC Action Type Setting code Keystone Get BE EF 03 06 00 B9 D3 02 00 07 20 00 00 Increment BE EF 03 06 00 DF D3 04 00 07 20 00 00 Decremen.
8 Command Data Chart (continued) RS-232C Communication (continued) Names Operation type Header Command data CRC Action Type Setting code Language Set English BE EF 03 06 00 F7 D3 01 00 05 30 00 00 FRA.
9 Command Data Chart (continued) RS-232C Communication (continued) Names Operation type Header Command data CRC Action Type Setting code Custom User B Set 50 BE EF 03 06 00 EF F6 01 00 B3 30 05 00 60 .
10 Command Data Chart (continued) RS-232C Communication (continued) Names Operation type Header Command data CRC Action Type Setting code V Position Get BE EF 03 06 00 0D 83 02 00 00 21 00 00 Incremen.
11 Command Data Chart (continued) RS-232C Communication (continued) Names Operation type Header Command data CRC Action Type Setting code Video NR Set LOW BE EF 03 06 00 26 72 01 00 06 22 01 00 MIDDLE.
12 Command Data Chart (continued) RS-232C Communication (continued) Names Operation type Header Command data CRC Action Type Setting code Volume Get BE EF 03 06 00 31 D3 02 00 01 20 00 00 Increment BE.
DUKANE CORPORATION FIVE-YEAR LIMITED WARRANTY This Dukane projector is warranted to the original purchaser for a period of five (5) years from the original purchase date – in normal operating conditions – against defects in material and workmanship .
Dukane Corporation Audio Visual Products Division 2900 Dukane Drive St. Charles, IL 60174-3395 E-mail: avsales@dukcorp.com Phone: (630) 762-4040 Orders: (800) 676-2485 Information: (800) 676-2486 Fax:.
デバイスDukane 8055の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Dukane 8055をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはDukane 8055の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Dukane 8055の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Dukane 8055で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Dukane 8055を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はDukane 8055の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Dukane 8055に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちDukane 8055デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。