DukaneメーカーImagePro 8915 8915 8915の使用説明書/サービス説明書
ページ先へ移動 of 84
User's Man ual LCD Pr ojector Model 8915.
.
Projector User's Manual - Safety Guide 1 About The Symbols Various symbols are used in this manual, the user’s manual and on the product itself to ensure correct usage, to prevent danger to the user and others, and to prevent property damage. The meanings of these symbols are described below.
2 Safety Pr ecautions W ARNING Never use the projector if a problem should occur. Abnormal operations such as smoke, strange odor, no image, no sound, excessive sound, damaged casing or elements or cables, penetration of liquids or foreign matter, etc.
W ARNING Be cautious of High temperatures of the projector. High temperatures are generated when the lamp is lit. It could result in fire or burn. Use special caution in households where children are present. Do not touch about the lens, air fans and ventilation openings during use or immediately after use, to prevent a burn.
W ARNING Be careful in handling the light source lamp. The projector uses a high-pressure mercury glass lamp made of glass. The lamp can break with a loud bang, or burn out. When the bulb bursts, it is possible for shards of glass to fly into the lamp housing, and for gas containing mercury to escape from the projector’s vent holes.
5 Safety Pr ecautions (continued) CAUTION Be careful in moving the projector. Neglect could result in an injury or damage. • Do not move the projector during use. Before moving, disconnect the power cord and all external connections, and close the slide lens door or attach the lens cap.
6 Safety Pr ecautions (continued) NOTE Do not give the remote control any physical impact. A physical impact could cause damage or malfunction of the remote control. • Take care not to drop the remote control. • Do not place the projector or heavy objects on the remote control.
7 Safety Pr ecautions (continued) NOTE Avoid strong rays. Any strong ray (such as direct rays of the sun or room lighting) onto the remote control sensors could invalidate the remote control. Avoid radio interference. Any interfering radiation could cause disordered image or noises.
Lamp 8 The projector uses a high-pressure mercury glass lamp. The lamp can break with a loud bang, or burn out, if jolted or scratched, handled while hot, or worn over time. Note that each lamp has a different lifetime, and some may burst or burn out soon after you start using them.
9 Regulatory Notices FCC Statement Warning WARNING: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
.
1 Projector ImagePro 8915 User Manual – Oper a ting Guide Thank you for purchasing this projector . WARNING ►Before using, read the "User's Manual - Safety Guide" and these manuals to ensure correct usage through understanding. After reading, store them in a safe place for future reference.
2 About this manual . . . . . . . . . . 1 Contents . . . . . . . . . . . . . . . . . 2 Projector features . . . . . . . . . . 3 Prepar ations . . . . . . . . . . . . . . 3 About contents of package . . . . . . . 3 Fastening the lens cap . . . . . . . .
3 Projector features / Prepar ations Projector features This projector is used to project various computer signals as well as NTSC/P AL/ SECAM video signals onto a screen. It requires just a little space for installation and gets a large image from short distance.
4 Y VIDEO RGB IN1 RGB IN2 DVI- D RGB OUT CONTROL AUDIO-IN REMOTE CONTRO L US B DC OU T S-VIDE O LA N COMPONENT VIDE O C B /P B C R /P R R-AUDIO IN-L AUDIO-OU T Par t names Lens ( 16 ) Filter cover ( 46 ) (Air filter and intake vent are inside.
5 ST ANDBY/ON VIDEO UP DOWN BLANK ASPECT PUSH LASER INDICAT OR LASER RGB ENTER ON OFF ESC POSITION MAGNIFY MUTE KEYSTONE FREEZE ONE TOUCH AUTO P A GE MENU RESET VOLUME ST ANDBY/ON INPU T KEYSTONE RESE.
6 Setting up Setting up WARNING ►Place the projector in a stable position horizontally . A fall or a turnover could cause an injury and/or damage to the projector .
7 (a) Screen size [inch (m)] (b) Projection distance [m (inch)] (c) Screen height [cm (inch)] min. max. down up 30 (0.8) 0.9 (35) 1.1 (42) 5 (2) 41 (16) 40 (1.0) 1.2 (47) 1.4 (57) 6 (2) 55 (22) 50 (1.3) 1.5 (59) 1.8 (71) 8 (3) 69 (27) 60 (1.5) 1.8 (71) 2.
8 Adjusting the pr ojector's ele vator WARNING ►Do not adjust the projector ’s elevator during use or immediately after use. Handling while the projector is in a high temperature could cause a burn and/or malfunction to the projector .
9 Setting up About the filter co v er f or bottom-up use WARNING ►Do not replace the filter cover during use or immediately after use. While the projector connects with a power supply , or the projector is in a high temperature state, handling could cause an electric shock, a fire, a burn and/or malfunction to the projector .
10 Setting up Connecting y our de vices CA UTION ►T urn of f all devices prior to connecting them to the projector . Attempting to connect a live device to the projector may generate extremely loud noise s or other a bnormalitie s that may r esult in mal function an d/or damage to the device and/or projector.
1 1 Y VIDEO RGB IN1 RGB IN2 DVI- D RGB OUT CONTROL AUDIO-IN REMOTE CONTRO L US B DC OUT S-VIDEO LA N COMPONENT VIDE O C B /P B C R /P R R-AUDIO IN-L AUDIO-OUT Y VIDEO RGB IN1 RGB IN2 DVI- D RGB OUT CO.
12 Y VIDEO RGB IN1 RGB IN2 DVI-D RGB OUT CONTROL AUDIO-IN REMOTE CONTRO L US B DC OU T S-VIDE O LAN COMPONENT VIDE O C B /P B C R /P R R-AUDIO IN-L AUDIO-OU T Y VIDEO RGB IN1 RGB IN2 DVI-D RGB OUT CON.
13 Setting up Connecting po wer supply WARNING ►Please use extra caution when connecting the power cord as incorrect or faulty connections may result in fire and/or electrical shock. • Only use the power cord that came with the projector . If it is damaged, contact your dealer to newly get correct one.
14 Putting ba tteries WARNING ►Always handle the batteries with care and use them only as directed. Improper use may result in battery explosion, cracking or leakage, which could result in fire, injury and/or pollution of the surrounding environment.
15 R emote control Using the r emote contr ol CA UTION ►Be careful in handling the remote control. • Do not drop or otherwise expose the remote control to physical impact. • Do not get the remote control wet or place it on wet objects. Doing so may result in malfunction.
16 STANDBY/ON VIDEO UP DOWN BLANK ASPECT PUSH LASER INDICATOR LASER RGB ENTER ON OFF ESC POSITION MAGNIFY MUTE KEYSTONE FREEZE ONE TOUCH AUTO PA GE MENU RESET VOLUME ST ANDBY/ON INPU T KE Y ST ON E RESE T MENU POWER TEMP LAMP P ow er on/of f Power on/of f WARNING ► When the power is on, a strong light is emitted.
17 Operating Operating Adjusting the v olume 1. Press the VOLUME button on the remote control. A dialog will appear on the screen to aid you in adjusting the volume. 2. Use the cursor buttons ▲/▼ to adjust the volume. T o close the dialog and complete the operation, press the VOLUME button again.
18 Operating Adjusting the zoom and f ocus 1. Use the zoom knob to adjust the screen size. 2. Use the focus ring to focus the picture. Adjusting scr een with ONE-T OUCH 1. Press the ONE T OUCH button on the remote control. This activates the following functions at one time.
19 Operating Using the automa tic adjustment fea tur e 1. Press the AUTO button on the remote control. At a RGB signal The vertical position, the horizontal position, the clock phase and horizontal size will be automatically adjusted. Make sure that the application window is set to its maximum size prior to attempting to use this feature.
20 Using the ma gnify f eature 1. Press the ON button of MAGNIFY on the remote control. The “MAGNIFY” indication will appear on the screen (although the indication will disappear in several seconds with no operation), and the projector will enter the MAGNIFY mode.
21 F r eezing the scr een 1. Press the FREEZE button on the remote control. The “FREEZE” indication will appear on the screen, and the projector will enter the FREEZE mode. T o exit the FREEZE mode and restore the screen to normal, press the FREEZE button again.
22 Oper a ting the computer scr een CA UTION ►Mistaken use of the mouse/keyboard control could damage your equipment. • While using this function, please connect only with a computer . • Before connecting, read the manuals of the computer you will connect.
23 Operating STANDBY/ON VIDEO UP DOWN BLANK ASPECT PUSH LASER INDICATOR LASER RGB ENTER ON OFF ESC POSITION MAGNIFY MUTE KEYSTONE FREEZE ONE TOUCH AUTO PA GE MENU RESET VOLUME Multifunctional settings Using the menu function This projector has the following menus: PICTURE, IMAGE, VIDEO Qlty .
24 Multifunctional settings EASY Menu Item Description ASPECT Using the buttons ◄/► switches the mode for aspect ratio. See the item ASPECT of section IMAGE menu ( 29 ). MODE Using the buttons ◄/► switches the mode of picture type. The modes of picture type are combinations of a mode of GAMMA and a mode of COLOR TEMP .
25 Multifunctional settings Item Description MIRROR Using the buttons ◄/► switches the mode for mirror status. See the item MIRROR of section SETUP menu ( 34 ). RESET Performing this item resets all of the items of EASY MENU except FIL TER TIME and LANGUAGE.
26 Multifunctional settings PICTURE Menu Item Description BRIGHT Using the buttons ▲/▼ adjusts the brightness. : Light Dark CONTRAST Using the buttons ▲/▼ adjusts the contrast. : Strong Weak GAMMA Using the buttons ▲/▼ switches the GAMMA mode.
27 Multifunctional settings Item Description COLOR TEMP Using the buttons ▲/▼ switches the mode of color temperature. HIGH MIDDLE LOW CUSTOM T o adjust CUSTOM Selecting the CUSTOM and then pressing the button ► or the ENTER button displays a dialog to aid you in adjusting the OFFSET and/or GAIN of CUSTOM mode.
28 Multifunctional settings Item Description MY MEMOR Y Selecting a mode of MY MEMOR Y using the buttons ▲/▼ and then pressing the button ► or the ENTER button perfo rms each function. LOAD1 LOAD2 LOAD3 LOAD4 SA VE4 SA VE3 SA VE2 SA VE1 This projector has 4 numbered memories for adjustment data.
29 Multifunctional settings IMAGE Menu Item Description ASPECT Using the buttons ▲/▼ switches the mode for aspect ratio. At a RGB/DVI signal 4:3 16:9 NORMAL At a video signal / no signal 4:3 16:9 SMALL • The NORMAL mode keeps the original aspect ratio of the signal.
30 Multifunctional settings Item Description H SIZE Using the buttons ▲/▼ adjusts the horizontal size. Large Small • This item can be selected only at a RGB signal (except DVI-D). • When this adjustment is excessive, the picture may not be displayed correctly .
31 Multifunctional settings VIDEO Qlty . Menu With the VIDEO Qlty . menu, items shown in the table below can be performed. Select an item using the cursor buttons ▲/▼ on the projector or remote control, and press the cursor button ► on the projector or remote control, or the ENTER button on the remote control to progress.
32 Multifunctional settings INPUT Menu Item Description COLOR SP ACE Using the buttons ▲/▼ switches the mode for color space. AUTO RGB SMPTE240 REC709 REC601 • This item can be selected only at a RGB signal or a component video signal (except signals of 525i(480i)/625i(576i) from the component video port).
33 Multifunctional settings INPUT Menu (continued) Item Description INFORMA TION Selecting this item displays a dialog titled “INPUT INFORMA TION”.
34 Multifunctional settings SETUP Menu Item Description WHISPER Using the buttons ▲/▼ turns off/on the whisper mode. NORMAL WHISPER • When the WHISPER is selected, acoustic noise and screen brightness are reduced. MIRROR Using the buttons ▲/▼ switches the mode for mirror status.
35 Multifunctional settings SCREEN Menu Item Description LANGUAGE Using the buttons ▲/▼ switches the OSD (On Screen Display) language. SUOMI POLSKI TÜRKÇE ENGLISH FRANÇAIS DEUTS.
36 Multifunctional settings Item Description ST ART UP Using the buttons ▲/▼ switches the mode for the start up screen. The start up screen is the screen displayed when no signal or an unsuitable signal is detected. MyScreen ORIGINAL TURN OFF MyScreen is the screen you can register a desired screen.
37 Multifunctional settings Item Description MESSAGE Using the buttons ▲/▼ turns on/off the message function. TURN ON TURN OFF When the TURN ON is selected, the following message function works. “AUTO IN PROGRESS” while automatically adjusting ”NO INPUT IS DETECTED” ”SYNC IS OUT OF RANGE” "Searching….
38 Multifunctional settings OPTION Menu Item Description ONE TOUCH Using the buttons ▲/▼ turns on/off the automatic keystone correction function. TURN ON TURN OFF Y ou can automatically correct vertical keystone distortion corresponding to the angle (forward/backward tilt) at which the unit is set up.
39 Multifunctional settings Item Description LAMP TIME The lamp time is the time counted after the last resetting. It is shown in the OPTION menu as the use time of the lamp. Pressing the RESET button on the remote control or the button ► of the projector for about 3 seconds displays a dialog.
40 Multifunctional settings NETWORK Menu Item Description DHCP Using the buttons ▲/▼ turns on/off the DHCP function. TURN ON TURN OFF If your network doesn’t support the DHCP f unction, select the TURN OFF . IP ADDRESS Enter the IP address of the projector using the ◄/►/▲/▼ buttons.
41 Multifunctional settings NETWORK Menu (continued) This projector provides the NETWORK function. When you star t to use this function, please consult your dealer for further information. T o start, connect the LAN port to a gateway device via a CA T -5 cable, then set up the projector according to the Network environment in which you use it.
42 Multifunctional settings NETWORK Menu (continued) Information 1) Allows you to confirm the current network settings of the projector . 2) Click on "return to top page" to return to Screen 2. Screen 3 Password Setting 1) Enter the current password.
43 4. If you modified the IP configuration or the DHCP setting, click on "Reboot" in Screen 2 to have the settings take effect. 5. Close the Web browser to end the configuration session.
44 Maintenance Maintenance Lamp WARNING HIGH VOL T AGE HIGH TEMPERA TURE HIGH PRESSURE ►The projector uses a high-pressure mercury glass lamp. The lamp can break with a loud bang, or burn out, if jolted or scratched, handled while hot, or worn over time.
45 Lamp (continued) When the indicators or a message prompts you to replace the lamp, replace the lamp as soon as possible. 1. T urn the projector off, and unplug the power cord. Allow the lamp to cool for at least 45 minutes. 2. T o prepare a new lamp, contact your dealer and tell the lamp type number = 456-8915 .
46 Maintenance When the indicators or a message prompts you to clean the air filter , clean the air filter as soon as possible. If the air filter becomes clogged by dust or the like, internal temperatures rise and the power may be automatically turned off for malfunction prevention.
47 Maintenance WARNING ►Before caring, make sure the power switch is off and the power cable is not plugged in, and then allow the projector to cool sufficiently . The care in a high temperature state of the projector could cause a burn and/or malfunction to the projector .
48 T r oubleshooting T roubleshooting R elated messages When the unit's power is on, messages such as those shown below may be displayed. When any such message is displayed on the screen, please respond as described below .
49 T r oubleshooting Related messages (continued) Message Description CHECK THE AIR FLOW The internal portion temperature is rising. Please turn the power OFF , and allow the unit to cool down at least 20 minutes. After having confirmed the following items, please turn the power ON again.
50 T r oubleshooting R e gar ding the indicator lamps Lighting and flashing of the POWER indicator , the LAMP indicator , and the TEMP indicator have the meanings as described in the table below . Please respond in accordance with the instructions within the table.
51 T r oubleshooting Regarding the indicator lamps (continued) POWER indicator LAMP indicator TEMP indicator Description Blinking In Red or Lighting In Red T urned off Blinking In Red The cooling fan is not operating. Please turn the power off, and allow the unit to cool down at least 20 minutes.
52 T r oubleshooting Phenomena tha t may easil y be mistak en for mac hine defects WARNING ►Never use the projector if abnormal operations such as smoke, strange odor , excessive sound, damaged casing or elements or cables, penetration of liquids or foreign matter , etc.
53 Phenomena that may easily be mistaken for machine defects (continued) Phenomenon Cases not involving a machine defect Reference page No pictures are displayed. The lens cap is attached. Remove the lens cap. 4, 16 The signal cables are not correctly connected.
54 War ranty And After-Ser vice W arranty and after-service If a problem occurs with the equipment, first refer to the “T roubleshooting” and run through the suggested checks. If this does not resolve the problem, please contact your dealer or the service company .
55 Specifications Specifications (continued) 336mm 95mm 265mm 109mm.
.
1 Projector Image P ro 891 5 User's Manual – Oper a ting Guide T echnical Example of computer signal Example of computer signal Resolution (H x V) H. frequency (kHz) V . frequency (Hz) Rating Signal mode 720 x 400 37.9 85.0 VESA TEXT 640 x 480 31.
2 Example of computer signal Initial set signals Initial set signals The following signals are used for the initial settings. The signal timing of some computer models may be different. In such case, adjust the items V POSITION and H POSITION in the IMAGE menu.
3 Y VIDEO RGB IN1 RGB IN2 DVI-D RGB OUT CONTROL AUDIO-IN REMOTE CONTROL USB DC OUT S-VIDEO LAN COMPONENT VIDEO C B /P B C R /P R R-AUDIO IN-L AUDIO-OUT Connection to the por ts Connection to the ports Connection to the ports A RGB IN 1, B RGB IN 2, C RGB OUT D-sub 15pin mini shrink jack • Video signal: RGB separate, Analog, 0.
4 Connection to the por ts D DVI -D DVI-D jack (digital to digital) Pin Signal Pin Signal 1 T .M.D.S. Data 2 - 13 - 2 T .M.D.S. Data 2 + 14 +5V Power 3 T .M.D.S. Data 2/4 Shield 15 Ground (+5V , Analog H/V .sync) 4 - 16 Hot-Plug Sense 5 - 17 T .M.D.S.
5 Connection to the por ts L AUDIO IN ( Ø3.5 stereo mini jack), J K AUDIO INL/R (RCA jack) • 200mV rms(max.) 50kΩ termination M AUDIO OUT ( Ø3.5 stereo mini jack) • 200mV rms(max.
6 RS-232C Communication RS-232C Communication RS-232C Communication 6 7 8 9 1 2 3 4 5 6 7 8 9 12 34 5 CONTROL port RS-232C cable (Cross) RS-232C port of the projector of the computer - (1) (1) CD RD (2) (2) RD TD (3) (3) TD - (4) (4) DTR GND (5) (5) GND - (6) (6) DSR RTS (7) (7) R TS CTS (8) (8) DTS - (9) (9) RI Connecting the cable 1.
7 RS-232C Communication (continued) Requesting projector status (Get command) (1) Send the request code Header + Command data (‘02H’+‘00H’+ type (2 bytes)+ ‘00H’ +‘00H’) from the computer to the projector . (2) The projector returns the response code ‘1DH’+ data (2 bytes) to the computer .
8 Names Operation T ype Header Command Data CRC Action T ype Setting Code Power Set Turn off BE EF 03 06 00 2A D3 01 00 00 60 00 00 T urn on BE EF 03 06 00 BA D2 01 00 00 60 01 00 Get BE EF 03 06 00 1.
9 Names Operation T ype Header Command Data CRC Action T ype Setting Code User Gamma Pattern Set Off BE EF 03 06 00 FB F A 01 00 80 30 00 00 9 step gray scale BE EF 03 06 00 6B FB 01 00 80 30 01 00 15.
10 Names Operation T ype Header Command Data CRC Action T ype Setting Code COLOR TEMP GAIN G Get BE EF 03 06 00 70 F4 02 00 B2 30 00 00 Increment BE EF 03 06 00 16 F4 04 00 B2 30 00 00 Decrement BE EF.
11 Names Operation T ype Header Command Data CRC Action T ype Setting Code PROGRESSIVE Set TURN OFF BE EF 03 06 00 4A 72 01 00 07 22 00 00 TV BE EF 03 06 00 DA 73 01 00 07 22 01 00 FILM BE EF 03 06 00.
12 Names Operation T ype Header Command Data CRC Action T ype Setting Code COLOR SP ACE Set AUTO BE EF 03 06 00 0E 72 01 00 04 22 00 00 RGB BE EF 03 06 00 9E 73 01 00 04 22 01 00 SMPTE240 BE EF 03 06 .
13 Names Operation T ype Header Command Data CRC Action T ype Setting Code MUTE Set TURN OFF BE EF 03 06 00 46 D3 01 00 02 20 00 00 TURN ON BE EF 03 06 00 D6 D2 01 00 02 20 01 00 Get BE EF 03 06 00 75.
14 Names Operation T ype Header Command Data CRC Action T ype Setting Code OSD BRIGHT Get BE EF 03 06 00 A8 D5 02 00 18 30 00 00 Increment BE EF 03 06 00 CE D5 04 00 18 30 00 00 Decrement BE EF 03 06 .
DUKANE CORPORATION FIVE-YEAR LIMITED WARRANTY This Dukane projector is warranted to the original purchaser for a period of five (5) years from the original purchase date – in normal operating conditions – against defects in material and workmanship .
Dukane Corporation Audio Visual Products Division 2900 Dukane Drive St. Charles, IL 60174-3395 E-mail: avsales@dukcorp.com Phone: (630) 762-4040 Orders: (800) 676-2485 Fax: (630) 584-5156 Parts & .
デバイスDukane ImagePro 8915 8915 8915の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Dukane ImagePro 8915 8915 8915をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはDukane ImagePro 8915 8915 8915の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Dukane ImagePro 8915 8915 8915の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Dukane ImagePro 8915 8915 8915で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Dukane ImagePro 8915 8915 8915を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はDukane ImagePro 8915 8915 8915の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Dukane ImagePro 8915 8915 8915に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちDukane ImagePro 8915 8915 8915デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
