DymoメーカーM1011の使用説明書/サービス説明書
ページ先へ移動 of 16
U ser Guide www .dymo.com.
2 A T ape cassette do or H Character selection window B T ape rollers I Cutting handle C T ape advance knob J Embossing adjustment screw D Start line K Cable tie slot punch E T ape pawl L Hole punch F.
3 About Y our New Labelmaker With your new DYMO M101 1 labelmaker , you can create a wide variety of plas tic and metal l abels. The labelmaker uses DYMO 12 mm (1/2") label tape.
4 Loading the Label T ape The DYMO M101 1 is set to emboss non-adhesive aluminium or plastic tape. T o load the tape roll 1. Hold the labelmaker in your left hand. 2. Open ta pe door (A). 3. Insert roll of tape allowing th e end to extend abou t 5 cm (2") through the tape slot.
5 Cutting the T ape T o cut the tape 1. Squeeze the emb ossing handle half-way , several times until the tape extends from th e front of the cutting assembly (M) by at least 1 cm (1"). Before cutting the tape, make sure the end of the tape extends beyond the edge of the cutting assembly so you can easily pull the label out.
6 Embossing th e Label Avoid turnin g the embossing wheel at the same time you are squeezing the embossing handle. This can damage the character blades. T o emboss a label 1. T urn the character selection wheel (G) until the desired letter is centered in the window (H).
7 Embossing on Stainless Ste el T ape Y ou may need to adjust the labe lmaker to emboss properly when using stainle ss steel tape. T o adjust for stainle ss steel tape 1. T urn the adjustment scre w (J) clockwise 1/2 to 3/4 turn. 2. Emboss the te xt as described in “Embossing the Label” on page 6.
8 Retracting the T ape Y ou may want to retract the tape, for exa mple, if the tape advanced too far or to center the tex t on the label. T o retract the tape 1.
9 Removing the T ape T o remove the tape 1. Retract the t ape as described in “Retracting t he T ape” on page 8. 2. Open the tape cassette door (A) and remove the tape. Use caution when removing stainless steel tape t hat may have sharp edges. 3. Reload th e tape as described in “Loading the Lab el T ape” on page 4.
10 Centering the T ext on the Label The leader/trailer lengt h guide (N) has positioning marks for a short (S) or long label (L). Use the marks on the guide to center the text on your label. T o center the tex t on a long label 1. After cutting th e previous label, emboss the text on a new label.
11 Applying Self-Adhesive Labels Self-adhesive plasti c and aluminum labels stick permanent ly to any smooth, clean, and dry surface. T o apply se lf-adhesive labels 1. Peel off the protect ive backing taking care not to touch the adhesive. 2. Press the label in place.
12 Punching Holes in Non-Adhesive Labels Y ou can choose to punch one or two holes in non-a dhesive labels so that the labels can be attached using screws, nails, rivets, and metal or plastic wires or ties. Y ou can al so punch a cable tie slot in one or both ends of the label.
13 Changing the Wheel Y ou can replace the character wheel with a Reverse Image Wheel. T o change the wheel 1. Remove the label tape. 2. Unscrew the screw in the center of the embossing wheel (G) and remove the wheel. 3. Position the new wheel. 4. Insert the screw in the center and tighten.
14 Hints for T rouble Free Operation Keep the follo wing in mind when using th e labelmaker: • Letters appear where you want spaces - Y ou are probably squeezing the embossi ng handle too hard. • Letters overlap - The tape is slipp ing. This can happen when dirt or grease gets on the rollers.
Contacting Customer Support The following table provides a list of telephone n umbers to reach DYMO Sales and Suppor t departments. Y ou can also reach DYM O at www.
W arranty Registration This DYMO M1 011 h as been manufactured und er strict quality control an d performance tested before leaving the factory. Within one year after purchase, DYMO will repair or rep.
デバイスDymo M1011の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Dymo M1011をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはDymo M1011の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Dymo M1011の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Dymo M1011で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Dymo M1011を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はDymo M1011の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Dymo M1011に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちDymo M1011デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。