Eagle Electronicsメーカー320の使用説明書/サービス説明書
ページ先へ移動 of 128
Pub. 988-0143-681 www.eaglesonar.com IntelliMap 320 Mapping GPS Receiver Installation and Operation Instructions .
Copyright © 2002 Eagle Electronics All rights reserved. Eagle ® is a registered trademark of Eagle Electronics Marine-Tex is a trademark of Illinois Tool Works Inc. Points of Interest Data in this unit are by infoUSA, copyright 2001-2002, All Rights Reserved.
i Table of Contents Section 1: Read Me First! ......................................................... 1 Capabilities and Specifications: IntelliMap 320 ...................... 2 How Eagle GP S Works ...............................................
ii Create Icon On Map ................................................................ 54 Create Icon At Cu rrent Posi tion ............................................ 54 Delete an Icon ................................................................
iii Map Datum Se lection ................................................................. 77 Map Detail Category Select ion................................................... 77 Map Orient ation .......................................................
iv WARNING! A CAREFUL NAVIGATOR NEVER RELIES ON ONLY ONE METHOD TO OBTAIN POSITION INFORMATION. CAUTION When showing navigation data to a po sition (waypoint), a GPS unit will show the shortest, most direct path to the waypoint. It provides navigation data to the waypoint regardless of obstructions.
1 Section 1: Read Me First! How this manual can get you out on the road, fast! Welcome to the exciting world of di gital GPS! We know you're anxious to begin navigating, but we have a favor to ask.
2 Section 3 contains short, easy-to-sc an GPS lessons that follow one an- other in chronological order. They're all you'll need to know to find your way on the water or in the wilderness quickly.
3 Input power: ................... 10 to 15 volts DC. Case size: ......................... 5.4" H x 6.9" W x 3.4" D (13.8 x 17.6 x 8.6 cm); sealed and waterproof; suitable for saltwater use. MMC slots: ...................... One with wate rproof door (SD card compati- ble).
4 NOTE: The above memory capacities refer only to the IntelliMap 320's on- board memory. The amount of GPS da ta you can record and save for recall later is only limited by the number of MMC cards you have.
5 The background map is suitable for many navigation chores, but for maximum accuracy and much more detail, you need our optional map- making software, MapCreate 6. Some unit features — such as searching for businesses and addre sses — won't work without a custom MapCreate map.
6 Introduction to GPS and WAAS Well, now you know the basics of how the unit does its work. You might be ready to jump ahead to Section 2, Installation & Accessories, on page 11, so you can mount your IntelliM ap 320 and plug in the power. Or you might want to see how our text formatting makes the manual tuto- rials easy to skim.
7 determine a position. This is called a 2D fix. It takes four satellites to determine both position and elevation (your height above sea level — also called altitude). This is called a 3D fix. Remember, the unit must have a clear view of the satellites in order to receive their signals.
8 receiver is only a tool. Always have another method of navigation avail- able, such as a map or chart and a compass. Also remember that this unit will al ways show navigation information in the shor.
9 3. You are asked to wait while it converts the trail into a route. 4. The wait message disappears and the IntelliMap 320 begins showing navigation information along the trail. Now, begin moving and follow your IntelliMap 320. Translated into complete English, step 1 above would mean: "Start on the Map Page.
10 Notes.
11 Section 2: Installation & Accessories Preparations You can install the GPS system in some other order if you prefer, but we recommend this installation sequence: Caution: You should read over this entire installation section before drill- ing any holes in your vehicle or vessel! 1.
12 You need to select an antenna insta llation location that has a clear, un- obstructed view of the sky. After the module is installed, route the cable to the unit, plug it in the center socket on the back and your system is ready to use.
13 For example, if you have to extend the power cable to the battery or power buss, attach one end of the fuse holder directly to the battery or power buss. This will protect both the unit and the power cable in the event of a short. It uses a 3-amp fuse.
14 Bracket Installation Mount the IntelliMap 320 in any conven ient location, provided there is clearance behind the unit when it's t ilted for the best viewing angle. You should also make sure there is en ough room behind the IntelliMap 320 to attach the power and GPS antenna/receiver module cables.
15 Front view (left) and side view (right) showing dimensions of the IntelliMap 320 when mounted on gimbal bracket. After drilling the hole, pass the antenna connector up through the hole from under the dash. Pass the power cable's bare-wire end down though the hole from the top.
16 In-dash mounting template for the IntelliMap 320, showing dimensions. NOTE: The figure above is not printed to scale. A scaled template (FM-5 In-Dash Adapter Kit instructions) is available for free download from our web site, www.
17 Install batteries in power pack battery adapter. MMC or SDC Memory Card Installation Your IntelliMap 320 uses a MultiMedia Card to store information, such as custom maps, waypoints, trails and other GPS data. The unit can also use Secure Digital Cards (SD card or SDC) to store data.
18 Memory card compartment with a 16 MB MMC card installed. To remove an MMC 1. Open the card compartment d oor by unscrewing the thumb screw. The screw should only be finger tigh t. If it was over-tightened, use a thumbnail, a coin or a screwdriver to open the door.
19 MapCreate™ 6 CD-ROM, left; MMC card reader for USB ports, right. Now that you have your IntelliMap 320 installed, move on to Section 3, Basic GPS Operations . There, we'll present a series of step-by-step tu- torials to teach you the basics of GPS navigation.
20 Notes.
21 Section 3: Basic GPS Operations This section addresses the IntelliMap 320's most basic GPS operations. The tutorials presented in Sec. 3 fo llow a chronological order. Sec. 4, Advanced GPS Operations , will discuss other more advanced functions and utilities.
22 3. MENU – Press this key to show the menus and submenus, which allow you to select a command or ad just a feature. This also accesses search functions for streets, inters ections, addresses and highway exits. 4. ARROW KEYS – These keys are used to navigate through the menus, make menu selections, move the map cursor and enter data.
23 You can access the Main Menu from any of the three Page screens by pressing MENU | MENU . To clear the menu screen and return to the page display, press EXIT . Main Menu. The Main Menu commands and their functions are: Screen command: changes the contrast or brightness of the display screen.
24 Browse MMC Files command: this allows you to view the installed MMC card and the files it contains. Pages The IntelliMap 320 has three Page di splays that represent the three major operating modes. They are th e Satellite Status Page, the Naviga- tion Page and the Map Page.
25 Satellite Status Page. Left view indicates unit has not locked on to any satellites and does not have a fix on its position. Center view shows sate l- lites being scanned. Right view shows satellite lock-on with a 3D position acquired (latitude, longitude and altitude), and WAAS reception.
26 The navigation screen looks lik e the one below when you're not navi- gating to a waypoint or following a route or trail. Your position is shown by an arrow in the center of the screen. Your trail history, or path you've just taken, is depicted by the line extending from the arrow.
27 to the destination. No matter what direction you are steering, the Bearing window shows the compass di rection straight to the destina- tion from your location at the moment. Distance shows how far it is to the waypoint you're navigating toward.
28 Navigation Page, backtracking a trail while creating a new trail. The Navigation Page has its own me nu, which is used for some ad- vanced functions and for setting various options. (Options and setup are discussed in Sec. 5). To access the Navigation Page Menu, from the Navigation Page, press MENU .
29 Far left, Map Page opening screen. Center, zoomed to 100 miles and right, zoomed to 10 miles. Over Zoomed means you have reached the detail limits in an area covered only by the basic background map. Zooming in any closer will reveal no more map details because a high- detail custom map has not been loaded on the MMC for this area.
30 The medium-detail U.S. maps contain: all incorporated cities; shaded metropolitan areas; county boundarie s; shaded public lands (such as national forests and parks); some major city streets; Interstate, U.
31 Tip: In some urban areas, businesses are so close to one another that their POI icons crowd each other on the screen. In the preceding figure, you can see a jumbled pile of POIs along Highway 34.
32 Pages Menu with Two Maps option selected, left. Map Page with two map windows, at right. The left map is active. Resize Window is another extremel y handy feature for pages that have two major windows. You can change th e horizontal size of the windows to suit your viewing preference.
33 Basic GPS Quick Reference Start outdoors, with a clear view of the open sky. As you practice, try navigating to a location at least a few blocks away. While you're learning, navigation in too small an area w ill constantly trigger arrival alarms.
34 Find Your Current Position Finding your current position is as simple as turning the IntelliMap 320 on. Under clear sky conditions, the unit automatically searches for satellites and calculates its position in approximately one minute or less. NOTE: "Clear sky" means open sky, uno bstructed by terrain, dense foliage or structures.
35 The selected airport to the northwest is 4.2 miles away. Selecting Any Map Item With the Cursor 1. Use the zoom keys and the arrow keys to move around the map and find the item you wish to select. 2. Use the arrow keys and center th e cursor cross-hair on the desired object.
36 3. The IntelliMap 320 says it is calc ulating, then a list of restaurants appears, with the closest at the top of the list, and the farthest at the bottom of the list. The nearest is highlighted. Find Waypoint Menu, left; Category Selection menu, center; and list of the nearest restaurants, right.
37 Map screen showing Finding Waypoint, the result of a restaurant search. 7. To clear the search and return to the last page displayed, press EXIT | EXIT | EXIT | EXIT . (Before you completely exited out of the Search menus, you could have gone looking for another place.
38 Sequence for setting a waypoint. Step 1: while traveling, quickly press WPT twice to call up Find Waypoint screen (seen in Step 2) and set a point. Step 3: a message says the waypoint has been saved. Step 4: vehi- cle continues on its way; number waypoint symbol is visible on map.
39 2. Press WPT | WPT . The waypoint is saved and automatically given a name with a sequential number, such as "waypoint 001." The waypoint symbol and number appear on the map. Create Waypoint by Entering a Position 1. Press WPT | → to S UBCATEGORY column| ↓ to N EW | ENT .
40 Navigation Page, navigating toward waypoint 004 and leaving a trail. Set Man Overboard (MOB) Waypoint One of boating's most terrifying even ts is having a friend or family member fall overboard. This situation can be deadly on any body of wa- ter — fresh or salt.
41 Navigating to Man Overboard: Navigation Page, left, and Map Page, right. The victim is astern of the vessel; the GPS shows which direc- tion to steer to for the rescue. The man overboard position is also st ored in the waypoint list for future reference.
42 Navigate to cursor. In this example, the cursor has selected the town of Oologah, Oklahoma. 3. Press MENU | ENT and the unit will begin navigating to the cursor lo- cation. The Map Page will display a dotted line from your current position to the cursor position.
43 Navigate to a Point of Interest For POIs that are in view on the map, you can easily use the Navigate to Cursor command above; just use the cursor to select the POI. The other method involves searchin g for POIs with the Find Waypoint command, launched with the WPT key.
44 Sequence for saving a trail and beginning a new one. At left, My Trails command. Center, the Trails Menu. The arrow to the right of Trail 14 indicates the trail is "active," and the check to the left indicates the trail is visible on the map display.
45 Tip: Another quick way to stop record ing one trail and begin a new one is to use the New Trail command: Press MENU | MENU | ↓ to M Y T RAILS | ENT | ENT . Caution: You also have the option of co mpletely turning off trail record- ing, under the trail Options command.
46 The other two methods provide a full ra nge of navigation data and work with both the Map Page and Naviga tion Page. The only difference be- tween them is "navigating a trail" follows a trail forward (from start to end) while "backtracking" follows a trail in reverse (from end to start.
47 Navigate a trail menu sequence: Fig. 1, My Trails command. Fig. 2, Trails Menu. Fig. 3, Edit Trail Menu. Fig. 4, Edit Route Menu with Navigate command highlighted for Trail 6. A trail is always converted to a "route" when you navigate the trail.
48 Navigate trail, navigation page (compass rose) views: at left, driver is northbound heading straight toward trail point 6; bearing arrow shows the trail point is due north (straight ahead). At right, driver has reached trail point 6 and must turn west to follow the trail.
49 Instructions for copying Custom Ma p Files to an MMC are contained in the instruction manual for your MMC card reader and MapCreate 6 software. For instructions on in serting an MMC into the IntelliMap 320, see Section 2, Installation/Accessories .
50 To transfer data from the MMC to the IntelliMap 320 : press → to L OAD | ENT . 3. Saving to MMC : To accept the default name "Data" for the GPS Data File, press ↓ to S AVE D ATA | ENT . If you wish to rename the file (as shown in the following figures), press ENT to activate the selection box.
51 These figures show the menu sequence for loading a GPS Data File from an MMC into the unit's memory. Cancel Navigation You can turn off any of the naviga tion commands after you reach your destination or at any other time by using the Cancel Navigation com- mand.
52 Notes.
53 Section 4: Advanced GPS Operations Find Distance From Current Position To Another Location 1. While on the Map Page press: MENU | ↓ to F IND D ISTANCE | ENT . 2. Center your cursor over the positi on you want to find the distance to. A rubber band line appears, connectin g your current position to the cursor's location.
54 Icons Icons are graphic symbols used to ma rk some location, personal point of interest or event. They can be plac ed on the map screen, saved and re- called later for navigation purposes. These are sometimes referred to as event marker icons. This unit has 42 different symbols you can pick from when creating an icon.
55 1. Press MENU | ↓ to D ELETE M Y I CONS | ENT . 2. Press ↓ to D ELETE A LL I CONS , D ELETE B Y S YMBOL , or D ELETE F ROM M AP and press ENT . Delete icons menu. The Delete All Icons command will ask if you are sure. Press ← to Y ES | ENT . All icons will be deleted from the map.
56 A route provides the automatic capability to navigate through several waypoints without having to reprogram the unit after arriving at each waypoint.
57 Edit Route menu, left. Edit Route Waypoints menu, right, with Add From Map command selected. 3. Use the Zoom keys and arrow keys to move the map and cursor until the cursor is centered on the spot where you want your route to begin.
58 Route creation sequence, from left: Fig. 1. Set route waypoint (1) at 11th St. & 145th Ave. Fig. 2. Zoom in; move cursor north to set point (2) at 145th & Admiral. Fig. 3. With point (2) set, move cursor east to mark interstate on-ramp with waypoint (3).
59 Delete a Route 1. From the N AVIGATION P AGE , press MENU | ENT or from the M AP P AGE press MENU | MENU | ↓ to R OUTE P LANNING | ENT . 2. Press ↓ to route name | ENT . 3. Press ↓ to N AVIGATE | ENT | → to D ELETE | ENT | ← to Y ES | ENT .
60 route by clicking on a map location with the cursor. Add Waypoint calls up the Waypoint List so you can in sert a waypoint from the list. Re- move Waypoint will delete the waypoi nt from the route. View Waypoint will show you where the select ed waypoint is on the map.
61 Navigating along a route: Fig. 1 shows the Navigation Page at the start of a route, heading straight for the first waypoint (Wpt 1). In Fig. 2, the traveler has arrived at Wpt 1; the arrival alarm has been triggered and the bearing arrow on the compass rose has turned to point toward Wpt 2, off to the east.
62 Tip: You can quickly call up the Edit Trail menu by selecting a trail on the map with the cursor. Simply mo ve the cursor over a trail and a pop-up box appears. Press WPT and the Edit Trail menu opens. At left, trail selected with map cursor. The pop-up box shows distance and bearing from current position to the selected point on the trail.
63 Alarm Clock To get to the alarm clock menu: press MENU | MENU | ↓ to T IMERS | ENT | ↓ to A LARM C LOCK | ENT . Sun/Moon Rise & Set Calculator To get to the Sun/Moon menu: press MENU | MENU | ↓ to S UN /M OON C ALCULATIONS | ENT . Trip Calculator To get to the Calculator menu: press MENU | MENU | ↓ to T RIP C ALCU- LATOR | ENT .
64 Waypoint Symbol To edit waypoint symbol: 1. Press WPT | ENT | ENT | ENT | ↓ to waypoint name | ENT | ↓ to E DIT W AYPOINT | ENT | ↓ to C HOOSE S YMBOL | ENT . 2. Use arrow keys to select desired symbol and press ENT . To return to the previous page, press EXIT | EXIT | EXIT | EXIT .
65 lected from your waypoint list, a ma p feature or from the Points of In- terest list. 1. Press WPT | → to S UBCATEGORY column| ↓ to N EW | ENT . 2. Press ↓ to P ROJECTED P OSITION | ENT | → to C REATE | ENT . 3. Press → to C HOOSE R EFERENCE | ENT .
66 Notes.
67 Section 5: System & GPS Setup Options Alarms This unit has several GPS alarms. The factory default setting has all the alarms turned on. You can turn the alarms off and on and change their distance settings. You can set an arrival alarm to fla sh a warning message and sound a tone when you cross a preset distance from a waypoint.
68 IMPORTANT ALARM NOTES: Anchor Alarm - The anchor alarm may be triggered even when you're sitting still. This typically happens when using small (less than .
69 GPS Auto Search on the Satellite Status Menu. You can force the unit to immediately kick into auto search mode. Here's how: 1. Press PAGES until you are on the Satellite Status screen. 2. Press MENU | ENT | ← to Y ES | ENT . Check MMC Files and Storage Space To check MMC Files: Press MENU | MENU | ↓ to B ROWSE MMC F ILES | ENT.
70 Menus for changing coordinate system used to display positions. To get to Coordinate System Selection: 1. Press MENU | MENU | ↓ to GPS S ETUP | ENT . 2. Press ↓ to C OORDINATE S YSTEM | ENT . This IntelliMap 320 can show a posi tion in degrees (36.
71 To setup Loran TD: NOTE: If the Loran TD conversion is ch osen, you must enter the local Lo- ran chain identification for the master and slaves. Do this by se- lecting "Setup Loran TD" at the bottom of the "Coordinate System" menu and select the ID.
72 1. Press MENU | MENU | ↓ to GPS S ETUP | ENT . 2. Press ↓ to C OORDINATE S YSTEM | ENT . 3. Press ↓ to S ETUP M AP F IX | ENT . The screen below appears, and M AP S CALE is highlighted. Press ENT and enter the map's scale. This is gene rally at the bottom of the paper map.
73 lighted and flashing, press ENT to open a list of options. Scroll ↑ and ↓ to select a different display option, then press ENT . After all options are set, press EXIT to return to the page display. Customize Map Page While on the Map Page, press PAGES | ↓ or ↑ to select Option Name | ENT .
74 Make the desired settings, then turn the simulator on by highlighting the GPS S IMULATOR O N box and pressing ENT key. Press EXIT | EXIT | EXIT to erase this menu. A message and tone appear periodically, warning you that the simulator is on. To turn the simulator off, repeat the above steps or turn the IntelliMap 320 off.
75 1. Press MENU | MENU | ↓ to GPS S ETUP | ENT | ENT . 2. A message appears, telling you to move the cursor near the desired location and press ENT . When the message automatically clears, follow the message instructions. 3. In a moment, your present position marker arrow appears on the map in the location you selected with the cursor.
76 Show Map Data From the Map Page, press MENU | ↓ to M AP D ATA | ENT . Press ENT to check S HOW M AP D ATA (turn on) and uncheck it (turn off). After the option is set, press EXIT | EXIT to return to the page display. Pop-up Map Info From the Map Page, press MENU | ↓ to M AP D ATA | ENT .
77 To set Lat/Long Grid: From the Map Page, press MENU | ↓ to M AP D ATA | ENT . Press ↓ to L AT /L ON G RID L INES . With the option highlighted, press ENT to check it (turn on) and unche ck it (turn off). After the op- tion is set, press EXIT | EXIT to return to the page display.
78 To get to Map Categories: 1. From the Map Page, press MENU | ↓ to M AP C ATEGORIES D RAWN | ENT . 2. Press ↑ or ↓ to select a category or press → then press ↑ or ↓ to select a subcategory. Press ENT to turn it off (no check) or on (checked).
79 Another option is course-up mode , which keeps the map at the same orientation as the initial bearing to the waypoint. When either the track-up or course-up mode is on, an "N" shows on the map screen to help you see which direction is north.
80 2. From the Map Page, press MENU | ↓ to M AP D ATA | ENT | ↓ to M AP C HOICE | ENT . Use ↑ or ↓ to select the Map Name , then press ENT | EXIT | EXIT . These figures show menu sequence (from left to right) for selecting a Navionics chart for the South Chesapeake Bay area.
81 Navionics chart showing Port Services icon selected by cursor. 3. To scroll through the Service Categories window: press ENT then use ↑ or ↓ to see the types of services available. As you highlight a different category, the list in the lower window changes.
82 When you zoom in to a sufficiently sm all zoom range, the icon itself be- comes an animated arrow showing tidal current velocity and direction for the selected tidal station at the present time. At larger zoom ranges, you can select the boxed " C " icon and it becomes an animated arrow with a pop-up name box.
83 The Tidal Current Information screen displays daily tidal current data for this station on this date at th e present time. The graph at the top of the screen is an approximate view of the flood and ebb pattern for the day, from midnight (MN), to noon (NN) to midnight (MN).
84 Navionics chart showing Tide Station icon selected by cursor. In the example above, the tide is at 2.8 feet and falling, as shown by the down arrow at the top of the icon. Tide Information screen. The Tide Information screen displays daily tidal data for this station on this date at the present time.
85 You can look up tidal data for othe r dates by changing the month, day and year selection boxes. To select another date: 1. Use → and ← to highlight month, day or year, then press ENT . 2. Use ↑ and ↓ to select the desired month, day or year, then press ENT .
86 rate plot trail if you are moving around in a relatively small area. If you want to experiment with Position Pinning, the same instructions are used to turn the feature on (checked) and off (unchecked.) 1. Press MENU | MENU | ↓ to GPS S ETUP | ENT | ↓ to P OSITION P INNING | ENT .
87 Screen Command, left, and Screen Menu with Contrast bar selected, right. To adjust the display's brightness: Press ↓ to B RIGHTNESS . Press → or ← to move the bar. The left end of the scale is minimum contrast; the right end is maximum contrast.
88 Set Local Time Using the correct local time setting is handy when estimating local ar- rival time while navigating. Also, th e time and date are saved when a waypoint is created. To access the Set Local Time menu, you must first acquire your posi- tion.
89 3. You can return to this command and press ENT again to turn the fea- ture on. Software Version Information From time to time, Eagle updates the operating system software in some of its products. These software upgrades are usually offered to customers as free downloads from our web site, www.
90 To set Alarm Sounds: Press ↓ to A LARM S OUNDS . With the option high- lighted, press ENT to check it (turn on) and uncheck it (turn off.) After the option is set, press EXIT | EXIT to return to the page display. To set Alarm Volume: Press ↓ to V OLUME .
91 Main Menu, left, Trails Menu, center, Trail Options, right. Delete All Trails To remove all of the trails from memory: from the Trails Menu, press → to D ELETE A LL | ENT | ← to Y ES | ENT . Flash Trails on Screen Option From the Trails Menu, press → to O PTIONS | ENT | ↓ to F LASH T RAILS .
92 With one of the Update Criteria selected, use the cursor arrows to highlight either the U PDATE R ATE or U PDATE D ISTANCE data entry boxes and press ENT . Press ↑ or ↓ to change the first character, then press → to the next character and repeat until the entry is correct.
93 Units of Measure This menu sets the speed and distance (statute or nautical miles, me- ters), depth (feet, fathoms, or meters), temperature (degrees Fahrenheit or Celsius) and heading (true or magnetic) units. To change the units: Press MENU | MENU | ↓ to S YSTEM S ETUP | ENT | ENT .
94 Notes.
95 Section 6: Searching NOTE: The background map loaded in your unit lets you to search for U.S. Interstate Highway exits and exit services, as well as some land features, including cities and lakes.
96 Find Address Menu. 4. To enter a street name , press ↓ to S TREET | ENT . There are two op- tions: A. You can spell out the name in the top selection box. Press ↑ or ↓ to change the first letter, then press → to move the cursor to the next letter and repeat until the name is correct, then press ENT | ENT .
97 Find City field, left, Search in particular city only option, center; Find City by name, right. 6. When the necessary search fields are filled in, press ↓ to F IND A D- DRESS | ENT . Your IntelliMap 320 asks you to wait while it searches for the address.
98 Information list. With the address lo cation selected by the cursor on the map, press WPT . The POI's Waypoint Information window ap- pears, with the Go To Waypoint command highlighted. If you want to go ahead and navigate to the POI address, just press ENT | EXIT .
99 Find Interstate Highway Exits 1. From the Map Page, press MENU | ↓ to H IGHWAY E XITS | ENT , which calls up the Find Exit menu. Find Highway Exits command, left, and Find Exit menu, right. 2. First, select a highway name by pressing ENT , which calls up the Find By Name menu.
100 Find Exit menu, with an exit selected in the Exit List. 4. In the Exit Information screen you have two choices. A. Press ENT to navigate or "go to" the exit. B. Press → | ENT to find the exit on the map. "Go To Exit" option, left, "Find On Map" option, right.
101 Find Map Places or Points of Interest (POI) 1. Press WPT , press ↓ or ↑ to select a map place or POI category, then press ENT . (To narrow your search, press → then press ↓ or ↑ to s elec t a subcategory before pressing ENT .) You will be given two options: Search By Name or By Nearest.
102 Find by Name option, left, Find by Name menu, right. 4. When the POI's Waypoint Information screen is displayed, you can choose to "Go To" the POI waypoint by pressing ENT or find it on the map by pressing → | ENT . "Go To" POI option, left, "Find on Map" POI option, right.
103 Find Streets command, left, Find Streets menu, right. 2. You must first fill in a street name in the First Street dialog box. Press ENT to display the Find By Name menu. There are two options: A. You can spell out the street in the top selection box.
104 you to wait while the IntelliMap 320 finds the street. When the Streets Found list appears, press ↑ or ↓ to select the street you are searching for and press ENT. At left, the Find Streets menu with the Find First Street command highlighted. At right, Streets Found list.
105 1. From the Map Page, press MENU | ↓ to F IND S TREETS | ENT and the Find Streets Menu appears. 2. You must fill in a street name in the First Street dialog box. Press ENT to display the Find By Name menu. There are two options: A. You can spell out the street in the top selection box.
106 appears, press ↑ or ↓ to select the intersection you are searching for and press ENT . (In the example on the previous page, we selected the intersection of SW 80th Street an d SW 71st Avenue in Miami, Fla.) 7. The Map Page appears, with the cursor pointing to the found inter- section.
107 3. If you're looking for nearest , the IntelliMap 320 says it is calcu- lating, then a list of waypoints appe ars. The closest is highlighted at the top of the list and the farthest at the bottom of the list. Calculating message, left, and list of the nearest waypoints, right.
108 select a waypoint from the list, then press ENT . The waypoint informa- tion screen appears. Find By Name menu, left. Waypoint Information screen, center. At right, the found waypoint is highlighted by the cursor on the Map Page. A. To navigate to the waypoint, press ENT .
109 Section 7: Supplemental Material Datums Used by This Unit WGS 1984 Default Adindan Mean for Ethiopia, Sudan Adindan Burkina Faso Adindan Cameroon Adindan Ethiopia Adindan Mali Adindan Senegal Adin.
110 DOS 1968 New Georgia Islands (Gizo Island) Easter Island 1967 Easter Island European 1950 Mean for Austria, Belgium, Denmark, Finland, France, West Germany, Gibraltar, Greece, Italy, Luxembourg, N.
111 North American 1927 Mean for CONUS (Continental United States) North American 1927 Mean for CONUS (East of Mississippi River) including Louisiana, Missouri, Minnesota North American 1927 Mean for .
112 Bolivia, Brazil, Chile, Colombia, Ecuador, Guyana, Paraguay, Peru, Trinidad & Tobago, and Venezuela South American 1969 Argentina South American 1969 Bolivia South American 1969 Brazil South A.
113 FCC Compliance This device complies with Part 15 of the U.S. Federal Communications Commission (FCC) Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
114 Notes.
115 Notes.
116 Notes.
117 EAGLE DATABASES LICENSE AGREEMENT THIS IS A LEGAL AGREEMENT BE TWEEN THE END-USER WHO FIRST PURCHASES THIS PRODUCT AS A CONSUMER ITEM FOR PERSONAL, FAMILY, OR HOUSEHOLD USE ("YO U") AND EAGLE ELECTRONICS, A DIVISION OF LEI, THE MANUFACTURER OF THIS PRODUCT ("WE", "OUR", OR "US").
118 DATABASES LIMITED WARRANTY "We", "our", or "us" refers to Eagle Electronics, a division of LEI, the manufacturer of this product. "You" or "your" refers to the first person who purchases the product as a consumer item for personal, family, or household use.
119 EAGLE ELECTRONICS FULL ONE-YEAR WARRANTY "We," "our," or "us" refers to EAGLE ELEC TRONICS, a division of LEI, the manufacturer of this product. "You" or "your" refers to th e first person who purcha ses this product as a consumer item for personal , family, or household use.
120 How to Obtain Service… …in the USA: We back your investment in quality pr oducts with quick, expert service and genuine Eagle replacement parts. If you're in the United States and you have technical, return or re pair questions, please contact the Factory Customer Service Department.
Accessory Ordering Information for all countries To order Eagle accessories such as power cables or transducers, please contact: 1) Your local marine dealer or consumer electronics store. Most quality dealers that handle marine electr onic equipment or other consumer electronics should be able to assist you with these items.
Visit our web site: www.eaglesonar.com Eagle Pub. 988-0143-681 © Copyright 2002 All Rights Reserved Printed in USA 101802 Eagle Electronics .
デバイスEagle Electronics 320の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Eagle Electronics 320をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはEagle Electronics 320の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Eagle Electronics 320の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Eagle Electronics 320で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Eagle Electronics 320を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はEagle Electronics 320の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Eagle Electronics 320に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちEagle Electronics 320デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
