Eagle ElectronicsメーカーID 128の使用説明書/サービス説明書
ページ先へ移動 of 32
1 ® Fish ID 128 Fish ID 128 Fish ID 128 Fish ID 128 Fish ID 128 INST INST INST INST INST ALLA ALLA ALLA ALLA ALLA TION AND OPERA TION AND OPERA TION AND OPERA TION AND OPERA TION AND OPERA TION TION .
2 Eagle Electronics PO Box 669 Catoosa, OK 74015 TABLE OF CONTENTS TABLE OF CONTENTS TABLE OF CONTENTS TABLE OF CONTENTS TABLE OF CONTENTS INTRODUCTION .............................................................................................. 3 SPECIFICATIONS .
3 SPECIFICATIONS Dimensions ...................... 5.9" W x 5.35" H x 3.4" D Input Voltage .................... 10 - 15 vDC Current Drain ................... 150 ma (lights off) ........................... 250 ma (lights on) Transmitter Frequency .
4 INSTALLATION - Bracket You can install the unit on the top of a dash or from an overhead with the supplied bracket. It can also be installed in the dash with an optional IDA- 3 or IDA-4 mounting kit. If you use the supplied bracket, you may be interested in the optional GBSA-1 swivel bracket kit.
5 PERMANENT MOUNT TRANSDUCER INSTALLATION The HS-WSPC supplied with your sonar is a transom mount transducer. It can be installed on any outboard or stern-drive (inboardoutboard) powered boat. The “kick-up” mounting bracket helps prevent damage if the transducer strikes an object while the boat is moving.
6 4. If possible, route the transducer cable away from other wiring on the boat. Electrical noise from engine wiring, bilge pumps, and areators can be displayed on the sonar’s screen. Use caution when routing the trans- ducer cable around these wires.
7 RATCHETS NUT MET AL W ASHER R UBBER W ASHERS MET AL W ASHER BOL T remov e the transducer and ratchets from the brac ket. Place the r atch- ets into the holes in the brack et with the letter “B” aligned with the dot stamped in the brack et. Reassemble the transducer and br ac k et and place them against the transom.
8 4. Hold the transducer and brac ket assemb ly against the transom. The transducer should be roughly parallel to the ground. The bottom of the transducer brac k et should be in line with the bottom of the hull. Don't let the brack et e xtend below the hull! Mark the center of the slots f or the mounting holes.
9 6. Route the transducer cab le to the sonar unit. Make cer tain to lea v e some slack in the cab le at the transducer as sho wn at the bottom of the previous page .
10 POWER CONNECTIONS -PERMANENT MOUNT UNITS ONLY IMPORTANT! INSTALL THE TRANSDUCER BEFORE WIRING THE POWER CABLE! The Fish ID 128 works from a 12 volt DC system only. For the best results, run the power cable directly to the boat’s battery. Keep the power cable away from other boat wiring, especially the engine’s wires.
11 FISH ID 128 PORTABLE ASSEMBLY INSTALLING THE BATTERIES INSTALLING THE BATTERIES INSTALLING THE BATTERIES INSTALLING THE BATTERIES INSTALLING THE BATTERIES Release the latch on the front of the battery case. Open the compartment and install eight "D" cell batteries into the adapter.
12 WASHER WASHER NUT BOLT TIE NYLON CORD HERE SCREW PORTABLE TRANSDUCER ASSEMBLY PORTABLE TRANSDUCER ASSEMBLY PORTABLE TRANSDUCER ASSEMBLY PORTABLE TRANSDUCER ASSEMBLY PORTABLE TRANSDUCER ASSEMBLY Assemble the transducer and bracket as shown below. Attach the transducer to the bracket with the supplied hardware.
13 Clean the chosen area of the hull before attaching the suction cup. Locate the transducer on the hull as shown below. Don't allow the bracket to go below the hull, as water pressure against it can cause the suction cup to come off at speed. Moisten the cup, then press it onto the hull as firmly as possible.
14 KEYBOARD BASICS The unit sounds a tone when you press any key. This tells you the unit has accepted a command. PWR/CLEAR Use this key to turn the unit on and off. It also clears menu selections and the menus from the screen. Note! To turn the unit off, press and HOLD the PWR/CLEAR down.
15 NOTE: Turning the unit off erases all user settings and it returns to the system defaults. For example, if you turn the lights on, then turn the unit off, the next time you turn the unit on, the lights will be off, since the default setting for the lights is off.
16 RANGE You can’t adjust the range when the auto- matic mode is on. It is adjustable when the unit is in the manual mode, however. To do so, first put the unit in the manual mode. Now press a menu key until the “RANGE SEL” menu appears as shown at right.
17 SENSITIVITY The sensitivity menu lets you control the unit’s ability to pick up echoes. A low sensitivity level excludes much of the bottom information, fish signals, and other detail. High sensitivity settings lets you see features, but it can also clutter the screen with noise and other unwanted signals.
18 floats, air bubbles, etc. Individual tree limbs extending outwards from a group of limbs are the hardest objects for the Fish ID feature to distinguish from fish. You may see Fish ID symbols on the screen when, in fact, there are no fish. Practice with the unit when the Fish ID feature is on and off to become more familiar with Fish ID.
19 CHART SPEED The rate echoes scroll across the screen is called the chart speed. It’s adjustable by pressing a menu key until the chart speed menu appears. Chart speed is set to maxi- mum when the unit is first turned on. To decrease it, press the down arrow key.
20 ALARMS FISH ALARM The Fish Alarm sounds a tone when a fish symbol appears on the screen. To use the fish alarm, press a menu key until the “FISH ALARM” menu appears on the screen. Now press the up arrow key to turn the alarm on. Repeat the above steps to turn the alarm off.
21 LIGHTS The display is backlighted for night use. To turn the backlights on or off, press a menu key repeatedly until the back light menu appears. Now press the up arrow to turn the lights on or the down arrow to turn them off. The menu will clear automatically after a few seconds.
22 automatically after a few seconds or press the PWR/CLEAR key to clear the screen. ASP (Advanced Signal Processing) ASP is a program embedded in the computer that is specifically designed to eliminate noise. It continually monitors the signals from the receiver, determines which echoes are noise and rejects them.
23 A A A A A BOAT'S DIRECTION OF TRAVEL BOAT'S DIRECTION OF TRAVEL BOAT'S DIRECTION OF TRAVEL BOAT'S DIRECTION OF TRAVEL BOAT'S DIRECTION OF TRAVEL A A A A A C C C C C B B B B B B B B B B C C C C C FISH ARCHES FISH ARCHES FISH ARCHES FISH ARCHES FISH ARCHES Fish arches are created when the cone of sound passes over a fish.
24 One of the best ways to get fish arches is to expand or “zoom” a segment of the water. For example, from 45 to 60 feet. The smaller the segment, the better the screen resolution will be. The easiest way to do this is with the Zoom feature. This feature expands the echoes, making it easier to see detail.
25 SURFACE LAYER ABSORBS HEAT FROM THE SUN EPILIMNION THERMOCLINE MOST PRODUCTIVE ZONE FOR FISHING HYPOLIMNION Unit won’t turn on: 1. Check the power cable’s connection at the unit. Also check the wiring. 2. Make certain the power cable is wired properly.
26 Unit freezes, locks up, or operates erratically: 1. Electrical noise from the boat’s motor, trolling motor, or an accessory may be interfering with the sonar unit. Rerouting the power and transducer cables away from other electrical wiring on the boat may help.
27 rejection feature. This can cause the unit to eliminate weaker signals such as fish or even structure from the display. Try using resistor spark plugs or routing the sonar unit’s power and transducer cables away from other electrical wiring on the boat.
28 unit’s power cable and transducer cable away from the wiring that is causing the interference. VHF radio antenna cables radiate noise when transmitting, so be certain to keep the sonar’s wires away from it. You may need to route the sonar unit’s power cable directly to the battery to isolate it from other wiring on the boat.
29 EAGLE ELECTRONICS FULL ONE-YEAR WARRANTY “We", “our”, or “us” refers to EAGLE ELECTRONICS, a division of LEI, the manufacturer of this product. “You” or “your” refers to the first person who purchases this product as a consumer item for personal, family, or household use.
30.
31 Ho w to Obtain Ser vice (Canadian Customers Only) We back your investment in quality products with quick, expert service and genuine Eagle replacement parts. If you need service or repairs, contact the Eagle Factory Customer Service Department at the toll-free number listed below.
32 Eagle Electronics may find it necessary to change or end our shipping policies, regulations, and special offers at any time. We reserve the right to do so without notice. Accessory Ordering Information To order accessories such as power cables or transducers, please contact: 1) Your local marine dealer.
デバイスEagle Electronics ID 128の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Eagle Electronics ID 128をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはEagle Electronics ID 128の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Eagle Electronics ID 128の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Eagle Electronics ID 128で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Eagle Electronics ID 128を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はEagle Electronics ID 128の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Eagle Electronics ID 128に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちEagle Electronics ID 128デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
