EAWメーカーKF730の使用説明書/サービス説明書
ページ先へ移動 of 28
KF730 & SB730 LOUDSPEAKER OWNER’S MANUAL Including KF730P & SB730P EAW Part: RD0169.
Page 2 of 28 RD0169 ( A) KF730 & SB730 OWNER’S MANUAL.
Page 3 of 28 RD0169 ( A) KF730 & SB730 OWNER’S MANUAL TABLE OF CONTENTS 1. READ THIS FIRST ................................................................................................................ 4 1.1 EC Statement Of Conformity ........
Page 4 of 28 RD0169 ( A) KF730 & SB730 OWNER’S MANUAL 1. READ THIS FIRST 1.1 EC STATEMENT OF CONFORMIT Y This document confirm s that the range of p rod ucts of Eastern Acoustic Works be aring t.
RD0169 (A) KF730 & SB730 OW NER’S MANUAL Page 5 of 28 2. INTRODUCTION The KF730 Line Array represents E AW’s latest technology for arrayable loudspe akers. The KF730 is a small format line a rray system for venues with listener distances u p to about 200 ft / 65 m.
Page 6 of 28 RD0169 ( A) KF730 & SB730 OWNER’S MANUAL 4. KF730 ARRAY DESIGN 4.1 KF730 WIZARD Use the KF730 Wizard for designin g KF730 arrays. It can be found in the Download s/Software section of the EAW we bsite (www.
RD0169 (A) KF730 & SB730 OW NER’S MANUAL Page 7 of 28 The horizontal pattern also features “soft sho u lders” that provide consistent frequency response to well beyond the nominal -6 dB points. These soft should ers can provide up to 150° of “usable ” horizontal coverage, albeit at somewhat reduced lev el.
Page 8 of 28 RD0169 ( A) KF730 & SB730 OWNER’S MANUAL When flown as part of a KF730 array, the SB730 s should be th e uppermost enclosure s in the array. In this application, the SB730s are su spended flat-fronte d, with the KF730s suspended below in the curvature determined by the KF730 Wizard.
RD0169 (A) KF730 & SB730 OW NER’S MANUAL Page 9 of 28 5. ARRAY OPERATION 5.1 OVERVIEW The operation of a KF730 Series system involves: 1. Understanding the principles on which it operate s. 2. How to electronically configure it for a specific task.
Page 10 of 28 RD0169 ( A) KF730 & SB730 OWNER’S M ANU AL 5.4.1 Factory Signal Processing Settings The signal proce ssing adjustments determin ed by EAW for the KF730 Series Array should be fully implemented “as is.
RD0169 (A) KF730 & SB730 OW NER’S MANUAL Page 11 of 28 The following tables list th e rms voltage limits for the KF730 and SB730. Because of th eir higher impedance design, multiple KF730s an d SB730s ca n be powered from single a mplifier chan nels.
Page 12 of 28 RD0169 ( A) KF730 & SB730 OWNER’S M ANU AL 5.7.3 Selecting an Appropriate Amplifier Size Rule Of Thumb If a KF730 Line Array is used for professionally opera ted co nce rt applications, a rule of thumb can be applied.
RD0169 (A) KF730 & SB730 OW NER’S MANUAL Page 13 of 28 5.8.2 SB730 Connections There are three Neutrik NL4MP and one NL 8MP connectors on the rear of each SB730. The connectors mate, respectively, with Neut rik NL4FC and NL8FC in-li ne cable connectors.
Page 14 of 28 RD0169 ( A) KF730 & SB730 OWNER’S M ANU AL 5.8.4 KF730P Input Connection s There are two 4-terminal bar rier strip connectors on the rear of each KF730P. The connectors are wi red in parallel so that the second connector can be used to loop LF and MF/HF signals to additional KF73 0s.
RD0169 (A) KF730 & SB730 OW NER’S MANUAL Page 15 of 28 6. RIGGING KF730 Series arrays are intended to be suspende d or ground-stacked. Thi s chapter details how to physically configure KF 730 Series arrays. The following are the recommended method s for most situations.
Page 16 of 28 RD0169 ( A) KF730 & SB730 OWNER’S M ANU AL For a given quantity of SB730: Max quantity KF730 = 18 - (1.5 x quantity SB730) Example, given five SB730: 18 - (1.5 x 5) = 10.5 which rounds down to a maximum quantity 10 KF730s For a given quantity of KF730: Maximum quantity SB730 = (18 - quantity KF730) / 1.
RD0169 (A) KF730 & SB730 OW NER’S MANUAL Page 17 of 28 6.4.3 Quick Release Pins Each KF730 is supplied with six 1.5 inch Q uick Release Pins. Four are used for attaching enclosures together or to the Fly-Ba r. Two are used as locking pins for the rear Hin ges.
Page 18 of 28 RD0169 ( A) KF730 & SB730 OWNER’S M ANU AL KF730 FLY-BAR HINGE TUBE HOLES DANGER: Each Hinge Tube on the Fly-Bar has two Quick Relea se Pin holes. When suspending KF730 or SB730s from the Fly-Bar, always use t he upper hole for attaching the encl osure Hinges.
RD0169 (A) KF730 & SB730 OW NER’S MANUAL Page 19 of 28 6.5 PALLETS 6.5.1 KF730 Face Pallet The KF730 Face Pallet is a wheeled pallet that holds two KF7 30s face down. Routing on the underside of the pallet al lows stacking loaded pallets two hig h.
Page 20 of 28 RD0169 ( A) KF730 & SB730 OWNER’S M ANU AL 6.7 SUSPENSION PROCEDURE S The basic procedure for suspending KF730s and SB 730s or a combination of both is si milar. What varies is how different pallet s affect ha ndling of the enclosures wh en being suspended.
RD0169 (A) KF730 & SB730 OW NER’S MANUAL Page 21 of 28 6.7.4 Attaching SB730s to SB730s Already Suspended NOTE: SB730s should always be flown tight-pa cked to each other. 1. Move an SB730 Pallet so its SB730 is positi oned under the bottom SB730 of the array.
Page 22 of 28 RD0169 ( A) KF730 & SB730 OWNER’S M ANU AL 5. Attach each Hing e to the Hinge Tube b y in serting a Quick Release Pin (removed in Step 2) through both. 6. Insert a Quick Release Pin (removed in ste p 2) into each of the enclosure’s rear Hinge Tubes as a locking pin.
RD0169 (A) KF730 & SB730 OW NER’S MANUAL Page 23 of 28 6.8.2 Stacking Additional Enclosures (SB730 as th e base) CAUTION: When attaching Hinges to Hi nge Tubes in st ep 5 fo r an SB730, position the SB730 so it lies flat on the SB730 below it.
Page 24 of 28 RD0169 ( A) KF730 & SB730 OWNER’S M ANU AL 6.8.5 Stacking Additional Enclosures (Fly-Bar as the base) CAUTION: When attaching Hinges to Hi nge Tubes in st ep 5 fo r an SB730, position the SB730 so it lies flat on the SB730 below it.
RD0169 (A) KF730 & SB730 OW NER’S MANUAL Page 25 of 28 7. CONTACTING EAW We have tried to answer any questions you ma y have about the KF730 and SB730 in this manual and in the KF730 Wizard Help file. Should you need further a ssistance, please d o not hesitate to contact us.
Page 26 of 28 RD0169 ( A) KF730 & SB730 OWNER’S M ANU AL 8. SERVICE AND MAINTENANCE 8.1 GENERAL SERVICE For any faults that cannot be fi eld-repaired a s noted below, contact the EAW Serv ice Department listed in Chapter 7 to determin e the appropriate action.
RD0169 (A) KF730 & SB730 OW NER’S MANUAL Page 27 of 28 8.4.2 Periodic Inspection Perform complete and thoroug h inspections on a routine, periodi c basis. The interval bet ween inspections and scope of the in spections will depend on the frequency of system usage and the conditions of use.
Page 28 of 28 RD0169 ( A) KF730 & SB730 OWNER’S M ANU AL © 2004 EASTERN ACOUSTIC WORKS ONE MAIN STREET WHITINSVILLE, MA 01588 2004 Mar RD0169.
デバイスEAW KF730の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
EAW KF730をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはEAW KF730の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。EAW KF730の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。EAW KF730で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
EAW KF730を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はEAW KF730の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、EAW KF730に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちEAW KF730デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。