EchoメーカーSRM - 2610の使用説明書/サービス説明書
ページ先へ移動 of 40
Grass T rimmer/Brush Cutter Operator's Manual MODELS, SRM - 2601 SRM - 2610 Serial Number 001001 & Up W ARNING DANGER W ARNING The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm.
2 I NTRODUCTION Welcome to the ECHO family. This ECHO product was designed and manufactured to provide long life and on-the-job- dependability. Read and understand this manual and the SAFETY MANUAL you found in the same package. You will find both easy to use and full of helpful operating tips and SAFETY messages.
G RASS T RIMMER /B RUSH C UTTER O PERA TOR ' S M ANUAL 3 This symbol accompanied by the words WARNING and DANGER calls attention to an act or condition that can lead to serious personal injury to operator and bystanders. The circle with the slash symbol means whatever is shown within the circle is prohibited.
4 INTERNA TIONAL SYMBOLS Shaft Decal W ARNING DANGER • This unit can be dangerous and cause serious injury if improperly used. To reduce injury risk to operator, helpers and bystanders, read and understand the Operator's and Safety manuals. • Blindness can occur from objects that are thrown or ricocheted even with shield in place.
G RASS T RIMMER /B RUSH C UTTER O PERA TOR ' S M ANUAL 5 EQUIPMENT W ARNING DANGER • Use only ECHO approved attachments. Serious injury may result from the use of a non approved attachment combination. Read and comply with all safety instructions listed in this manual and safety manual.
6 FUEL W ARNING DANGER Fuel is VERY flammable. Use extreme care when mixing, storing or handling, otherwise serious personal injury may result. • Use an approved fuel container. • DO NOT smoke near fuel. • DO NOT allow flames or sparks near fuel.
G RASS T RIMMER /B RUSH C UTTER O PERA TOR ' S M ANUAL 7 Physical Condition -- Your judgment and physical dexterity may not be good: • if you are tired or sick, • if you are taking medication, • if you have taken alcohol or drugs. Operate unit only if you are physically and mentally well.
8 SAFE OPERA TION Determine Operation Area • Provide all operators of this equipment with the Operator's Manual and instructions for safe operation. • Review the area to be trimmed. Look for hazards that could contribute to unsafe conditions.
G RASS T RIMMER /B RUSH C UTTER O PERA TOR ' S M ANUAL 9 EXTENDED OPERA TION / EXTREME CONDITIONS Vibration and Cold It is believed that a condition called Raynaud’s Phenomenon, which affects the fingers of certain individuals may be brought about by exposure to vibration and cold.
10 Contents List Items MODELS 2610 1E 2601 1E √ √ √ √ √ √ √ √ √ √ √ √ √ √ √ √ √ √ √ √ √ √ √ √ √ √ √ √ √ √ √ √ √ √ √ √ √ √ .
G RASS T RIMMER /B RUSH C UTTER O PERA TOR ' S M ANUAL 11 EMISSION CONTROL -- The emission control system for this engine is EM (Engine Modification). Emission Control Label located on Engine (EXAMPLE ONLY, information on label varies by FAMILY).
12 1. OPERATOR'S MANUAL - Included in plastic bag (co-pack). Read before operation and keep in a safe place for future reference, i.e., operation, maintenance, storage and specifications.
G RASS T RIMMER /B RUSH C UTTER O PERA TOR ' S M ANUAL 13 S PECIFICA TIONS MOD EL SR M- 2601 1E SR M- 2610 1E Len gt h 1800 mm ( 70. 9 i n . ) 1800 mm ( 70. 9 i n . ) Wi d t h 315 m m ( 1 2. 4 i n . ) 600 mm ( 23 . 6 i n . ) Hei ght 285 mm ( 1 1.
14 A SSEMBL Y DRIVE SHAFT / POWER HEAD Tools Required: 4 mm Hex Wrench Parts Required: Power head, Drive shaft Assembly 1 . Loosen, the bolt (A) at engine drive shaft clamp. 2 . Carefully fit drive shaft assembly to engine making sure that inner drive shaft engages into clutch mount.
G RASS T RIMMER /B RUSH C UTTER O PERA TOR ' S M ANUAL 15 B A PLASTIC SHIELD INST ALLA TION (for Nylon Line Operation) Tools Required: Screwdriver. Parts Required: Plastic Shield, Shield Plate, three (3) 5mm x 15mm screws. NOTE The plastic shield is for use with the Nylon Line Head only.
16 NOTE For SRM-2610 handle assembly refer to "U-Handle Installation page 18 instructions 1, 10, 12 - 16. ACCESSOR Y INST ALLA TION Blade Conversion Kit P/N 99944200415, U-Handle / Blade Conversion Kit P/N 99944200521, Muffler Bracket Kit P/N 10099057730.
G RASS T RIMMER /B RUSH C UTTER O PERA TOR ' S M ANUAL 17 INST ALL MET AL SHIELD Tools Required: 8mm x 10mm Open End Wrench, Screwdriver. Parts Required: Metal Shield, Bracket, 3 - 5 mm x 15 mm s.
18 U - HANDLE INST ALLA TION Tools Required : 8mm x 10mm Open End Wrench, Screwdriver, 3mm and 4mm Hex Wrench, Pliers Parts Required: U-Handle/Blade Conversion Kit P/N 99944200521. NOTE For model SRM-2610 use Steps 1, 10, 12 - 16. 1 . Close choke and remove air filter cover.
G RASS T RIMMER /B RUSH C UTTER O PERA TOR ' S M ANUAL 19 1 2 . Route throttle linkage and ignition lead assembly around front of U-Handle bracket and clip to drive shaft as shown. 1 3 . Place throttle linkage (E) through adjustment fixture (F) and install wire end into large carburetor throttle swivel hole (D).
20 P RE - O PERA TION OPERA TION WITH BLADES Preparing the Trimmer/Brush Cutter for Blade Use W ARNING DANGER Blade use DEMANDS specific Brush Cutter configuration.
G RASS T RIMMER /B RUSH C UTTER O PERA TOR ' S M ANUAL 21 Choosing the Correct Blade W ARNING DANGER The type of Blade used MUST be matched to the type and size of material cut. An improper or dull blade can cause serious personal injury. Blades MUST be sharp.
22 FUEL Fuel Requirements Gasoline - Use 89 Octane [ ] (mid grade or higher) gasoline or gasohol known to be good quality. Gasohol may contain up to 10% Ethyl (grain) alcohol or 15% MTBE (methyl tertiary-butyl ether). Gasohol containing methyl (wood) alcohol is NOT approved.
G RASS T RIMMER /B RUSH C UTTER O PERA TOR ' S M ANUAL 23 After Refueling; • Wipe any spilled fuel from the unit. • Move at least 3 M (10 ft.) from refueling location before starting. After Use; • DO NOT store a unit with fuel in its tank. Leaks can occur.
24 DETERMINE OPERA TION AREA W ARNING DANGER Inspect starting area for hazards such as rocks, glass, debris etc. which could be contacted by the cutting attachment when starting. Keep helpers and bystanders at least 15 M (50 ft.) from starting area, otherwise serious personal injury may result.
G RASS T RIMMER /B RUSH C UTTER O PERA TOR ' S M ANUAL 25 2. Close Choke - Cold Start. Move choke lever (B) to Cold Start Position. 3. Primer - Pump Bulb. Pump primer bulb (C) 10 times until fuel is visible in the “Clear” fuel return line (D).
26 2. Primer - Pump Bulb. Pump primer bulb (C) until fuel is visible in the "Clear" fuel return line (D). 3. Start - Pull Rope. Lay the trimmer on a flat clear area and pull the recoil starter handle (E) until the engine fires. STOPPING ENGINE 1.
R ECORT ADORA DE HIERBA /C ORT ADORA DE MALEZA M ANUAL DEL OPERADOR 2 7 INTERV ALOS DE MANTENIMIENTO / e t n e n o p m o C a m e t s i S e d o t n e i m i d e c o r P o t n e i m i n e t n a M s a i r.
28 W ARNING DANGER Fuel is VERY flammable. Use extreme care when mixing, storing or handling. 1 . Use a clean rag to remove loose dirt from around fuel cap and empty fuel tank. 2 . Use the “fuel line hook” to pull the fuel line and filter from the tank.
G RASS T RIMMER /B RUSH C UTTER O PERA TOR ' S M ANUAL 29 SP ARK PLUG Level 2. Tools Required: T-Wrench (combination socket wrench & screw driver supplied with unit) Feeler gauge, preferably a wire gauge. Soft Metal Brush. Parts Required: Spark Plug, NGK BPM-7Y P/N 99944500071 1 .
30 1 . Remove air filter cover (A). 2 . Remove spark plug lead. 3 . Remove two (2) muffler cover screws and muffler cover (B). 4 . Remove screw and arm rest (C). 5 . Remove two (2) front cylinder cover screws and cylinder cover (D). IMPORTANT DO NOT use a metal scraper to remove dirt from the cylinder fins.
G RASS T RIMMER /B RUSH C UTTER O PERA TOR ' S M ANUAL 31 1 . Remove engine cover (A). See “Cleaning Cooling System” pages 29 & 30 for step by step instructions. 2 . Place piston at Top Dead Center (TDC) to prevent carbon/dirt from entering cylinder.
32 A LUBRICA TION Level 1. Tools Required: 8 mm Open End Wrench, Screwdriver, Clean Rag. Parts Required: Lithium Base Grease. Gear Housing 1 . Clean all loose debris from gear box. 2 . Remove plug (A) and check level of grease. 3 . Add grease if necessary, DO NOT over fill.
G RASS T RIMMER /B RUSH C UTTER O PERA TOR ' S M ANUAL 33 3 . Hold the spool, opening toward you. Place index finger between the two strands and wind line, tightly and evenly, in direction of arrow marked "CC". 4 . Stop when approximately 15-20 cm (6 - 8 in.
34 SHARPENING MET AL BLADES Three styles of metal blades are approved for use on the ECHO Brush Cutter. The 8-tooth blade can be sharpened during normal maintenance.
G RASS T RIMMER /B RUSH C UTTER O PERA TOR ' S M ANUAL 35 T ROUBLESHOOTING Pr ob l em E ng i n e -- s ta rt s ha rd En gin e - - does n ot st ar t Ca us e Re me dy En gi n e Cr a n k s Fu el at c.
36 S TORAGE Long T erm Storage (over 30 days) W ARNING DANGER During operation the muffler or catalytic muffler and surrounding cover become hot. Always keep exhaust area clear of flammable debris during transportation or when storing, otherwise serious property damage or personal injury may result.
G RASS T RIMMER /B RUSH C UTTER O PERA TOR ' S M ANUAL 37 NOTES.
38 NOTES.
G RASS T RIMMER /B RUSH C UTTER O PERA TOR ' S M ANUAL 39 NOTES.
ECHO, INCORPORA TED 400 O AKWOOD R OAD L AKE Z URICH , IL 60047 DEALER? Call 1-800-432-ECHO 1-800-432-3246 ECHO Incorporated 400 Oakwood Road Lake Zurich, IL 60047 Technical Publications Orders S ER V.
デバイスEcho SRM - 2610の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Echo SRM - 2610をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはEcho SRM - 2610の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Echo SRM - 2610の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Echo SRM - 2610で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Echo SRM - 2610を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はEcho SRM - 2610の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Echo SRM - 2610に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちEcho SRM - 2610デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
