Eclipse - Fujitsu TenメーカーAVN5510の使用説明書/サービス説明書
ページ先へ移動 of 16
Contents Contents Components Installation Diagram Before installation Installation Connections 2 For your safety in using the AVN5510 3 5 Names and functions of terminals 6 Installing the GPS antenna .
- 2 - Components Components Check that all of the following components are present Check that all of the following components are present GPS antenna components GPS antenna x 1 10 Waterproof cushion x.
- 3 - Warnings and caution signs, illustrated below, are posted throughout this manual as well as on the AVN5510. They show safe and correct ways to handle the main unit to prevent personal injury to you and others and avoid damage to property.
- 4 - • • This main unit must be operated only as on-board main unit, or it may cause electrical shock or injury. • • Do not play distorted sounds for long periods of time; the speakers may overheat and cause a fire.
- 5 - Installation Diag Installation Diag r r am am GPS antenna (When installing inside the vehicle) 10 GPS antenna (When installing outside the vehicle) 10 • • If installing the GPS antenna inside the vehicle, the location and the slope of the vehicle's windshield will determine the accuracy of the GPS antenna to receive the GPS signal.
- 6 - • • Never cut the insulation on the power wire or use it to power any other equipment. If the rated current capacity of the power wire is exceeded, fire and electric shocks may result. • • The wires should be secured with tape or a similar securing method to prevent any obstructions while driving.
- 7 - Wire colors and connection points f or connection wires , and 4 3 2 Never connect the power supply to the speaker wires (No.7 and No.8), otherwise it will cause damage to the main unit. Caution B+ (Yellow) Connect where power is constantly available, regardless of the ignition key's position.
- 8 - English Español Français Italiano Nederlands Svenska English VTR output terminals Connect to the monitor with video input. Genuine steering remote control terminal Connect to the vehicle steering remote control. ※ Compatible vehicle models for installation : Vehicles with voltage detection-type steering remote control.
- 9 - Vehicle component adapter wires Vehicle harness From main unit - Example of using vehicle adapter wires - - V ehicle connections - Power supplies for combined equipment Español Français Italia.
- 10 - Notes on installation • • Check the vehicle speed pulse signal, parking brake signal, and reverse signal carefully before making the connections. If the wires are incorrectly connected, accidents or problems with correct operation may result.
Route the parking brake signal wire to the main unit. - 11 - Foot-operated parking brake Hand-operated parking brake - A connecting the point for parking brake signal (example) - Attach a splicing connector at this location.
- 12 - System connection e System connection e xample xample • • Install and connect all of the peripheral units before connecting them to the main unit. • • Do not remove any of the protective caps (RCA, etc.) unless in use. • • Be sure to wrap the connection wires with tape (PVC tape) to insulate them.
- 13 - Tip Installing the GPS antenna Installing the GPS antenna Notes on installation • • Do not install the antenna in places (such as front pillars and roof panel) that are shielded from the sky.
- 14 - - Installation inside the vehicle (example) - Choose an installation location on the dashboard which is flat and has a clear view of the sky. 1 Install the ground plate to the dashboard. 2 Install the GPS antenna to the ground plate. 3 Ground plate 12 Secure the GPS antenna.
- 15 - - Installation outside the vehicle (example) - Choose an installation location where the GPS antenna can be attached securely. 1 Remove the backing paper from the body protective sheet and attach the sheet to the vehicle. 2 Install the GPS antenna on top of the body protective sheet.
Remove the pocket and any other accessories from the center cluster to make room for the main unit. 1 Remove the mounting brackets for the pocket. 2 Attach the brackets to the main unit. 3 Install the main unit in the vehicle. 4 Be careful not to forcefully push on the main unit's display or buttons during installation.
デバイスEclipse - Fujitsu Ten AVN5510の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Eclipse - Fujitsu Ten AVN5510をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはEclipse - Fujitsu Ten AVN5510の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Eclipse - Fujitsu Ten AVN5510の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Eclipse - Fujitsu Ten AVN5510で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Eclipse - Fujitsu Ten AVN5510を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はEclipse - Fujitsu Ten AVN5510の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Eclipse - Fujitsu Ten AVN5510に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちEclipse - Fujitsu Ten AVN5510デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
