EdimaxメーカーEW-7303APNの使用説明書/サービス説明書
ページ先へ移動 of 68
.
WLAN Broadband Router User Manual 1 1. T erminology ............................................................................................................................................... 3 2. Introduction .....................................
WLAN Broadband Router User Manual 2 6.17.6. Management - Save / Reload Settings ............................................................................................. ...................... 54 6.17.7. Management - Pa ssword Se tup .............
WLAN Broadband Router User Manual 3 1. Terminology 3DES Triple Data Encryption Standard AES Advanced E ncryption Standa rd ANSI American National Standards Institute AP Access Point CCK Complementary .
WLAN Broadband Router User Manual 4 WDS Wireless Distribution System WEP Wire d Equivalent Privacy WLAN Wireless Local Area Network WPA Wi-Fi Protected Access 2.
WLAN Broadband Router User Manual 5 3. Product Features Generic Router Compatible with IEEE 802.11n Specifications prov ides wireless speed up to 150Mbps data rate. Compatible with IEEE 802.11g high rate standard to prov ide wireless Ethernet spee ds of 54Mbps data rate.
WLAN Broadband Router User Manual 6 LED Indicator State Description on The WLAN Broadband Router is p owered on. 1. PWR LED off The WLAN Broadband Router is powered off. Flashing Data is transmitting or re ceiving on the antenna. 2. WLAN LED off No data is transmitting or receiving on the antenna.
WLAN Broadband Router User Manual 7 3.3. 4. Appearance and Interface Introduction 4.1. Hardware Installation: 4.1.1. products Appearance Notes:The product shot is for reference only please refer to physical product.
WLAN Broadband Router User Manual 8 Wall Mount Pole Mount Lan port with POE WAN port with POE Reset Button.
WLAN Broadband Router User Manual 9 4.1.2. Hard ware installation steps Step1: push buttons in the sides to remove upper housi ng. Step2: Pass through Ethernet cable from the hole, insert the cabl e to LAN port.
WLAN Broadband Router User Manual 10 Step3: Install the upper housing Make sure the housing is well in stalled. Step4: Install POE Injector DC:Insert adapter POE:this hole is linked to Outdoor AP with.
WLAN Broadband Router User Manual 11 Step5: Complete diagram.
WLAN Broadband Router User Manual 12 4.1.3. Software Installation There are no software drivers, patches or utilities installati on needed, but only the configur ation setting.
WLAN Broadband Router User Manual 13 4.1.4. 4.1.5. 5. Software configuration There are web based management and c onfiguration functions allowing you to have the jobs done easily. The WLAN Broadband Router is delivered with the fo llowing facto ry default parameters on the Ethernet LAN interfaces .
WLAN Broadband Router User Manual 14 4. Select Protocol in the Network Com ponent Type dialog box and click Add button. 5. Select TCP/I P in Microsoft of Select Network Protocol dialog box then click OK button to install the TCP/ IP protocol, it may need the Microsoft Windows CD to complete the installation.
WLAN Broadband Router User Manual 15 6. Status This page shows the curre nt status and some basic settings of the device, includes sy stem, wirele ss, Ethernet LAN and WAN configuration informatio n. Item Description System Uptime It shows the duration since WLAN AP Router is powered on.
WLAN Broadband Router User Manual 16 SSID It shows the SSID of this WLAN AP Router. The SSID is the unique name of WLAN AP Router and shared among its service area, so all device sat tempts to join the same wireless network can identify it. Channel Number It shows the wirel ess channel connected currently.
WLAN Broadband Router User Manual 17 6.1.1. Operation Mode This page followed by Setup Wizard page to define the ope ration mode. 6.1.2. Time Zone Setting This page is used to enable and configu re NTP client.
WLAN Broadband Router User Manual 18 6.1.3. LAN Interface Setup This page is used to configure local are a network IP address and subnet mask. 6.1.4. WAN Interface Setup This page is used to configure WAN a ccess type.
WLAN Broadband Router User Manual 19 6.1.5. Wireless Basi c Settings This page is used to configure ba sic wireless paramet ers like Band, Mode, Network Type SSID, Chan nel Number, Enable Mac Clone(Single Ethernet Client).
WLAN Broadband Router User Manual 20 This page is used to configure wireless security. 6.2. Operation Mode This page is used to configure whi c h mode wireless bro adband router acts.
WLAN Broadband Router User Manual 21 Item Description Gateway Traditional gateway configuration. It always connects internet via ADSL/Cable Modem. LAN interface, WAN interface, Wireless interface, NAT and Firewall modules are applied to this mode Bridge Each interface (LAN, WAN and Wirele ss) regards as bridge.
WLAN Broadband Router User Manual 22 Item Description Disable Wireless LAN Interface Click on to di sable the wireless LA N data transmission. Band Click to select 2.4GHz(B ) / 2.4GHz(G) / 2.4GHz(N) / 2.4GHz(B+G)/ 2.4GHz(G +N) / 2.4GHz(B+G+N) Mode Click to select the WLAN AP / Client / WDS / AP+WDS wireless mode.
WLAN Broadband Router User Manual 23 pull-down menu. Broadcast SSID Click to enable or di sabl e the SSID broadcast function. WMM Click Enabled/Disabled to init WMM feature. Data Rate Select the transmis sion data rate from pull-down menu.Data rate can be auto-select, 1M to 54Mb ps or MCS.
WLAN Broadband Router User Manual 24 Item Description Fragment Threshold Set the data packet fragmentation threshold, value can be written between 256 and 2346 bytes. RTS Threshold Set the RTS Threshold, value can be written between 0 and 2347 bytes. Beacon Interval Set the Beacon Interval, value can be written between 20 and 1024 ms.
WLAN Broadband Router User Manual 25 Item Description Select SSID Select the SSI D from multiple APs. Encryption Select the encryption supported over wirel ess access. The encryption method can be None, WEP, WPA, WPA2 or WPA-Mixed. Use 802.1x Authentication While Encryption is selected to be WEP.
WLAN Broadband Router User Manual 26 HEX 10 hexadecimal code s 26 hexadecimal code s 6.6. Wireless - A ccess Control If you enable wireless access control, only those clients whos e wireless MAC ad dresses are in the access control list will be able to connect to your Access Point.
WLAN Broadband Router User Manual 27 Delete Selected Click to delete the se lected clients that will be access right removed from this WLAN Broadband Router. Delete All Click to delete all the registered clients from the access allowed list. Reset Click the Reset button to abort change and recover the previous configuration setting.
WLAN Broadband Router User Manual 28 Set Security Click button to configure wireles s security like WEP(64bits), WEP(128bits), WPA(TKIP), WPA2(AES) or None Show Statistics It shows the TX , RX packets, rate statistics. Delete Selected Click to delete the se lected clients that will be access right removed from this WLAN Broadband Router.
WLAN Broadband Router User Manual 29 Item Description MAC Address It shows the MAC Address within WDS. Tx Packets It shows the statistic count of sent packets on the wireless LAN interface. Tx Errors It shows the statistic c ount of error sent packets on the Wireless LAN interface.
WLAN Broadband Router User Manual 30 Item Description SSID It shows the SSID of AP. BSSID It shows BSSID of AP. Channel It show the current channel of AP occupied. Type It show which type AP acts. Encrypt It shows the encryption status. Signal It shows the power level of current AP.
WLAN Broadband Router User Manual 31 Item Description Disable WPS Click on to disable the Wi-Fi Protected Setup function. WPS Status Show WPS status is Configured or UnConfigured . Self-PIN Number Fill in the PIN Num ber of AP to register the wireless distribution system access capability.
WLAN Broadband Router User Manual 32 Item Description IP Address Fill in the IP address of LAN interfaces of this WLAN Access Point. Subnet Mask Fill in the subnet mask of LAN interfaces of this WLAN Access Point. Default Gateway Fill in the default gateway for LAN interfaces out going data packets.
WLAN Broadband Router User Manual 33 802.1d Spanning Tree Select enable or disable the IEEE 802.1d Spanning Tree function from pull-down menu. Clone MAC Address Fill in the MAC addres s that is the MAC address to be cloned Apply Changes Click the Apply Changes button to complete the new configuration setting.
WLAN Broadband Router User Manual 34 Reset Click the Reset button to abort change and recover the previous configuration setting. 6.12. WAN Interface Setup This page is used to configure the para meters for wide ar ea network that connects to the WAN port of your WLAN Broadband Router.
WLAN Broadband Router User Manual 35 IP Address If you select t he Static IP support on WAN interface, fill in the IP address for it. Subnet Mask If you select t he Static IP support on WAN interface, fill in the subnet mask for it.
WLAN Broadband Router User Manual 36 Item Description DHCP Client Click to select DHCP support on WAN interface for IP address assigned automatically from a DHCP server. Host Name Fill in the host name of Host Name. The default value is empty. MTU Size Fill in the mtu size of MTU Size.
WLAN Broadband Router User Manual 37 DNS 1 Fill in the IP address of Domain Name Server 1. DNS 2 Fill in the IP address of Domain Name Server 2. DNS 3 Fill in the IP address of Domain Name Server 3. Clone MAC Address Fill in the MAC address that is the MAC address to be cloned.
WLAN Broadband Router User Manual 38 Item Description PPPoE Click to select PPPoE support on WAN interface. There are user name, password, connection type and idle time settings need to be done. User Name If you select the PPPoE support on WAN interface, fill in the user name and password to login the PPPoE server.
WLAN Broadband Router User Manual 39 interface, fill in the user name and password to login the PPPoE server. Service Name Fill in the service name of Service Name. The default value is empty. Connection Type Select the connection type from pull-down menu.
WLAN Broadband Router User Manual 40 response. Enable Web Server Access on WAN Click the checkbox to enable web configuration from WAN side. Enable IPsec pass through on VPN connection Click the checkbox to enable IPSec packet pass through. Enable PPTP pass through on VPN connection Click the checkbox to enable PPTP packet pass through.
WLAN Broadband Router User Manual 41 Item Description PPTP Allow user to make a tunnel with remote site directly to secure the data transmission among the connection. User can use embedded PPTP client supported by this router to make a VPN connection.
WLAN Broadband Router User Manual 42 from a PPTP server. IP Address If you select the PPTP support on WAN interface, fill in the IP address for it. Subnet Mask If you select the PPTP support on WAN interface, fill in the subnet mask for it.
WLAN Broadband Router User Manual 43 connection pass through. Enable PPTP pass through on VPN connection Click the checkbox to enable PPTP packet pass through. Enable L2TP pass through on VPN connection Click the checkbox to enable L2TP packet pass through.
WLAN Broadband Router User Manual 44 Apply Changes Click the Apply Changes button to complete the new configuration setting. Reset Click the Reset button to abort change and recover the previous configuration setting. Delete Selected Click to delete t he selected port range that will be removed from the port-filtering list.
WLAN Broadband Router User Manual 45 Reset Click the Reset button to abort change and recover the previous configuration setting. Delete Selected Click to delete t he selected port range that will be removed from the IP-filtering list. Delete All Click to delete all t he registered entries from the IP-filtering list.
WLAN Broadband Router User Manual 46 removed from the MAC-filtering list. Delete All Click to delete all t he registered entries from the MAC-filtering list. Reset Click the Reset button to abort change and recover the previous configuration setting. 6.
WLAN Broadband Router User Manual 47 Reset Click the Reset button to abort change and recover the previous configuration setting. Delete Selected Click to delete the selected IP address and port number that will be removed from the port-forwarding list.
WLAN Broadband Router User Manual 48 URL Filtering list. Reset Click the Reset button to abort change and recover the previous configuration setting. 6.16.5. Firewall - DMZ A Demilitarized Zone is used to provide In ternet services without sa crificing unauthorized acce ss to its local private network.
WLAN Broadband Router User Manual 49 Item Description Wireless LAN Sent Packets It shows the statistic count of sent packets on the wireless LAN interface. Received Packets It shows the statistic count of received packets on the wireless LAN interface.
WLAN Broadband Router User Manual 50 Item Description Enable DDNS Click the checkbo x to enable DDNS service. Service Provider Click the dr op down menu to pickup the right provider. Domain Name To configure the Domain Name. User Name/Email Configure User Name, Email.
WLAN Broadband Router User Manual 51 Item Description Current Time It show s th e current time. Time Zone Select Click the time zone in your country. Enable NTP client update Click the checkbox to enable NTP client update. NTP Server Click select default or input NTP server IP address.
WLAN Broadband Router User Manual 52 Item Description Enable DoS Prevention Click the checkbox to enable DoS prevention. Whole System Flood / Per-Source IP Flood… Enable and setup prevention in details. Select ALL Click the checkbox to enable all prevention items.
WLAN Broadband Router User Manual 53 Apply Changes Click the Apply Changes button to save above settings. 6.17.4. Management - Log This page is used to configure the rem o te log server and show n the current log . Item Description Enable Log Click the checkbox to enable log.
WLAN Broadband Router User Manual 54 6.17.5. Management - Upgrade Firmwa re This page allows you upgrade the Access Poi nt firmware to new version. Please note, do not power off the device during the upload because it may crash the syste m. Item Description Select File Click the Browse button to select the new version of web firmware image file.
WLAN Broadband Router User Manual 55 Reset Settings to Default Click the Reset button to reset the configuration parameter to factory defaults. 6.17.7. Management - Password Setup This page is used to set the account to access the web se rver of Access Point.
WLAN Broadband Router User Manual 56 To find your PC’s IP and MAC address, Open the Command program in the Microsoft Wind ows. Type in ipconfig /all then press the Enter button. Your PC’s IP address is the one entitled IP Address a nd your PC’s MAC address is the one entitled Physical Address.
WLAN Broadband Router User Manual 57 7.5. What is BSSID? A six-byte address that distinguishes a particula r a partic ular access point from others. Also know as just SSID. Serves as a network ID or name. 7.6. What is ESSID? The Extended Service Set ID (ESSID) is the name of the network you want to ac cess.
WLAN Broadband Router User Manual 58 If you find that your corrupted packets or asymmetric packe t recept ion (all send packets, for example). You may want to try lowering your fragmentation threshold. This will ca use packe ts to be broken into smaller fragments.
WLAN Broadband Router User Manual 59 7.17. What is 802.1x Authentication? 802.1x is a framework for authent icated MAC-level access cont rol, defines Extensible Au thentication Protocol (EAP) over LANs (WAPOL).
WLAN Broadband Router User Manual 60 7.26. What is NTP Client? NTP client is designed for fetching the current timesta mp fr om internet via Network Time protocol. User can specify time zone, NTP server IP address. 7.27. What is VPN? VPN is the abbreviation of Virtual Priv ate Network.
WLAN Broadband Router User Manual 61 8. Configuration examples 8.1. Example one - PPPoE on the WAN Sales division of Company ABC likes to establish a WL AN network to support mobile communi cation on sales’ Notebook PCs. MIS engineer collects inf ormation and plan s the WLAN Broadband Router implementation b y the following configuration.
WLAN Broadband Router User Manual 62 8.1.2. Configure the LAN interface: Open LAN Interface Setup page, enter the IP Addres s “192.168.1.254”, Subnet Mask “255.255.255.0”, Default Gateway “0.0.0.0”, enable DHCP Server , DHCP cli ent range “192.
WLAN Broadband Router User Manual 63 8.1.3. Configure the WLAN interface: Open WLAN Interface Setup page, enter the SSID “AP”, Channel Number “11”.
WLAN Broadband Router User Manual 64 8.2. Example two - fixed IP on the WAN Company ABC likes to establish a WLA N network to support mobile communication on all employees’ Noteboo k PCs. MIS engineer collects information and pl ans the WLAN Broadband Router implementation by the following configuration.
WLAN Broadband Router User Manual 65 Channel Number 11 8.2.1. Configure the WAN interface: Open WAN Interface Setup page, select Fixed IP then enter IP Addres s “ 192.168.2.254 ”, subnet mask “ 255.255.255.0 ”, Default gateway “ 192.168.2.10 ”.
WLAN Broadband Router User Manual 66 8.2.3. Configure the WLAN interface: Open WLAN Interface Setup page, enter the SSID “AP”, Channel Number “11”.
WLAN Broadband Router User Manual 67.
デバイスEdimax EW-7303APNの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Edimax EW-7303APNをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはEdimax EW-7303APNの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Edimax EW-7303APNの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Edimax EW-7303APNで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Edimax EW-7303APNを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はEdimax EW-7303APNの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Edimax EW-7303APNに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちEdimax EW-7303APNデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
