Electroluxメーカー137019200の使用説明書/サービス説明書
ページ先へ移動 of 20
137064300 A (080 1) In stallation In struction s Electr olux Front-Load Was her In strucciones de In stalacion Lav adora de car ga frontal Electr olux In struction s d’in stallation Lav euse à char.
2 Finding Information Please r ead and save this guide Thank you for choosing Electrolux , the new pr emium brand in home appliances. These Installation Instructions are part of our commitment to customer satisfaction and pr oduct quality throughout the life of your new appliance.
3 Safety Important Safety Instructions Recognize safety symbols, words and labels Safety items throughout this manual ar e labeled withaWARNINGorCAUTIONbasedontherisk type as described below: T ools and materials needed for installation: WHA T TO DO IF YOU SMELL GAS: Donottrytolightanyappliance.
4 Electrical system r equirements W ater supply requir ements Gr ounding requir ements Drain system r equirements CIRCUIT - Individual, properly polarized and grounded 15 amp.
5 MINIMUMINST ALLA TIONCLEARANCES-Inches(cm) SIDES REAR TOP FRONT Alcove 0” (0 cm) 0” (0 cm)* 0” (0 cm) n/a Under - Counter 0” (0 cm) 0” (0 cm)* 0” (0 cm) n/a Closet 0” (0 cm) 0” (0 cm)* 0” (0 cm) 1” (2.54 cm) Installation Requir ements Clearance r equirements 0” (0cm) 0” (0cm) 1” (2.
6 Installation Requir ements 38.00” (96.52cm) 53.00” (134.62cm) 50.6” (128.53cm)* to clear open door 31.50” (80.01cm)* to front of closed door water supply connection on rear of unit ¹ drain hose on rear of unit ² power cord on rear of unit ³ freestand washer on floor floor line floor line washer mounted on optional pedestal 27.
7 Unpacking W asher Removing foam packaging T emporarily remove door tape. 1. Open washer door and remove everything fr om 2. the drum. Close door and reapply door tape. 3. Using a rug, blanket or piece of cardboar d to 4. protect the floor , carefully lay the washer on it’ s back.
8 Unpacking W asher Removing shipping har dware Installing hole plugs NOTE Ru bber ex pans ion mat eri al on spacers may need time to relax befor e they can be easily pulled through shipping hole. IMPOR T ANT Save all shipping bolts and spacers for future use.
9 Installation Instructions raise lower Leveling your washer Excessive noise and vibration can be prevented by properly leveling the washer . For free standing installation and with the 1. washer within 4 feet (1 m) of its final location, place a level on top of the washer .
10 Run some water from the hot and cold faucets 1. to flush the water lines and remove particles tha t mi ght c log the w ater valv e sc ree ns an d to determine which faucet is hot and which is cold supply . Lookintheendofeachwatersupplyinlethose 2.
11 Snap one end of the drain hose hanger 1. (shipped in washer drum) onto the drain hose. Continue wrapping it around the hanger and snap it in place. Place the hook end of the drain hose in the drain 2. opening. Secure the drain hose with the cable tie (provided in the enclosur e package) to the stand - pipe, inlet hose, laundry tub, etc.
12 If your washer has this console: If your washer has this console: Empty washer’ s drum and close door . 1. After you plug in the washer the first time: wake up the washer by pressing any button, r otate cycle 2. knob to hand wash cycle, press the start button and then the cancel button.
13 W ARNING ELECTRICALSHOCKHAZARD Failure to disconnect power sour ce before servicing could result in personal injury or even death. B)RemovingDoorfromHinge 1 Reopen door to 90 degree angle. 2 Remove 4 long, course-thread, counter -sunk hinge screws fr om door .
14 Reversing Door W ARNING ELECTRICALSHOCKHAZARD Failure to disconnect power sour ce before servicing could result in personal injury or even death. C) Removing Hinge from Fr ont Panel 1 With the hinge in open position, remove 2 short, course-thread, panhead scr ews on hinge plate.
15 Reversing Door E)ReattachingDoorLocktoFrontPanel 1 Rotate the door lock and move it to the opposite opening. 2 Connect the harness to the door lock by inserting it in the terminal and firmly pushing it in place. 4 Secure the lock with 2 short, course-thr ead, panhead screws.
16 Reversing Door H)RemovingLatchIndicator 1 Insert flat blade screwdriver into open slot of latch indicator . 2 Gentlypryupwardtor eleasetab. 3 Pull the indicator out and set it aside. 3 Pull the hole plug out and set it aside.
17 insert tab insert tab insert tab insert tab press down and snap press down and snap K)ReattachingStrikerPlate 1 Rotate the striker plate and move it to the opposite side of door above the indicator . 2 Reattach with 2 long, course-thread, counter -sunk screws.
18 M)ReattachingDoorAssembly 1 Open the hinge to a 90 degree angle. 2 Install the door onto the hinge locating pins. N) Reversing T rim Ring 1 T rim ring orientation is marked on the back. 2 Remove the trim ring cover plate. T o remove the cover plate from the right, pivot point is up.
19 If replacements parts ar e needed for your washer , contact the source wher e you purchased your washer ,call1-877-4ELECTROLUX(1-877-435- 3287), or visit our website, www .electroluxappliances.com, for the Electrolux AuthorizedPartsDistributornearestyou.
20 Notes.
デバイスElectrolux 137019200の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Electrolux 137019200をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはElectrolux 137019200の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Electrolux 137019200の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Electrolux 137019200で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Electrolux 137019200を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はElectrolux 137019200の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Electrolux 137019200に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちElectrolux 137019200デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。