ElectroluxメーカーBuilt-In Side-by-side Refrigeratorsの使用説明書/サービス説明書
ページ先へ移動 of 22
Installation Instructions Built-In Side-By-Side Refrigerators If you have questions, call 1-877-4ELECTROLUX 877-435-3287 or visit our website at: BEFORE YOU BEGIN Read these instructions completely and carefully . • IMPOR T ANT — Observe all governing codes and ordinances.
Installation Instructions 16 HARDW ARE SUPPLIED • Anti-T ip brackets Anti-T ip Brackets MA TERIALS REQUIRED • 36 ″ long, 2 ″ x 4 ″ wood block for Anti-T ip bracket installation • #12 or #14 wood screws for Anti-T ip bracket • Screws to secure refrigerator to cabinets • 1/4 ″ O.
THE INST ALLA TION SP ACE Water and Electrical Locations The opening must be prepared with the electrical and water supply located as shown. The cutout depth must be 24 ″ The refrigerator will project forward, slightly beyond adjacent cabinets, depending on your installation.
1/2" 1" 3/4" Custom Panel (Nominal Size) 1/4" 1/2" 3/4" 2" 1-1/4" 1-1/2" 1-3/4" 3" 2-1/4" 2-1/2" 2-3/4" 1/4" 1/2" 3/4&qu.
1/2" 1/4" 1/2" 3/4" 1" 1-1/4" 1-1/2" 23-7/8" From Rear of Refrigerator 3/4" Custom Panel (Nominal Size) Case T rim Refrigerator Fresh Food Door Backer Pane.
CUSTOMIZA TION BASICS: Stainless Steel Wrapped Models Stainless Steel Wrapped Refrigerators Stainless Steel wrapped refrigerators have wrapped doors and grille panels, and beveled edges.
1/4 ″ FRAMED P ANEL DIMENSIONS If you choose to install framed panels, they must be cut to the dimensions shown. The panels will slide into the frame on the door and grille. IMPORT ANT NOTE: Maximum weight for Fresh Food panel is 70 pounds and 30 pounds total for Freezer panels.
3/4 ″ FRAMED CUSTOM P ANEL OPTION For a more custom appearance, 3/4 ″ framed custom panels may be installed on trimmed models. The overlay panel is secured to a 1/4 ″ finished backer panel. The assembled custom panel then slides into the trim with the same procedure described on page 33.
3/8" 3-1/8" 5/16" 1" Thick Max. or 3/4" Plus 1/4" Backer B 2-1/2" 3-1/8" Min. 1/4" Max. A 5/16" Required for Optimal Handle Clearance 3/4 ″ FRAMED CUSTOM WOOD P ANELS Secured to a 1/4 ″ finished backer panel.
2-1/2" 3-1/8" Min. 1/4" Max. Required for Optimal Handle Clearance 3/8" 3-1/8" 1" Thick Max. or 3/4" Plus 1/4" Backer 5/16" A 5/16" B 3/8" 1" Thick Max. or 3/4" Plus 1/4" Backer 5/16" 5/16" 3-1/8" A B 1" Thick Max.
1/4" Max. Required for Optimal Handle Clearance 3-1/8" 2-1/2" 3-1/8" Min. B A 3/4 ″ FULL-WIDTH OVERLA Y CUSTOM P ANELS This panel design provides a nearly trimless appearance. Assemble the spacer panel onto the finished backer panel.
3-1/8" Min. 1/4" Max. Required for Optimal Handle Clearance 3-1/8" 3-1/8" 5/16" 5/16" A B A B A B 2-1/2" 3/4 ″ FULL-WIDTH OVERLA Y CUSTOM P ANELS This panel design provides a nearly trimless appearance. Assemble the spacer panel onto the backer panel.
GROUNDING THE REFRIGERA TOR IMPORT ANT — Please read carefully FOR PERSONAL SAFETY , THIS APPLIANCE MUST BE PROPERL Y GROUNDED. The power supply cord of this appliance is equipped with a three-prong.
1 REMOVE P ACKAGING CAUTION: Refrigerator is T op-Heavy —be careful when moving. When using an appliance dolly , handle from Freezer side only . • Carefully cut banding at the top and bottom; remove outer carton. • Slide out rear corner posts (2).
2 INST ALL W A TER LINE • A cold water supply is required for automatic icemaker operation. The water pressure must be between 40 and 120 psi. • Route 1/4 ″ O.D. copper tubing between cold water line and the water connection location. • T ubing should be long enough to extend to the front of the refrigerator .
3 INST ALL SIDE P ANELS SKIP THIS STEP WHEN NOT USING SIDE P ANELS If you are using 1/4" side panels, they should be inserted into the case trim. Fasten the panels to the refrigerator with the 3M Dual Lock adhesive strips before setting refrigerator in place.
7 LEVEL REFRIGERA TOR All models have 4-point leveling. The front and back are supported by leveling legs. Both are accessible from the front of the refrigerator . • T o level the back of the refrigerator , turn the 1/2 ″ hex nut located above the front wheels.
10 INST ALL GRILLE P ANEL • Raise the grille panel to the stop position. • Remove 4 screws on bottom trim; retain all screws. • Remove bottom trim. • NOTE: Stainless steel and acrylic panels are covered with a protective film. Remove the film before installing the panel.
11A Install 1/4 ″ Decorative Panels: • Remove Handles Open door to 90°. Remove 5 Phillips head screws from the Fresh Food and Freezer door handles; retain all screws. Lift off door handles. • Install Door Panels NOTE: Stainless steel and acr ylic panels are covered with a protective film.
11B 1. Remove handles from cartoning and any other protective packaging. 2. Place handle over pre-installed shoulder bolts (A) that are fastened into door in four locations. 3. While supporting handle and looking at upper end cap, fasten top-most allen set screw (B) with supplied allen wrench, then fasten bottom allen set screw (C).
13 TURN ON THE POWER • Set the Master Power switch to the I (ON) position. • Check to make sure power to refrigerator is on by opening refrigerator door to see if interior lights are on. • The temperature controls are preset at 37° for the Fresh Food section and 0° for the Freezer section.
16 DOOR ALIGNMENT • Stand back from the refrigerator to inspect the door alignment. • Shipping or the addition of heavy door panels may have caused the doors to move slightly out of alignment. • If necessary , the Fresh Food door may be adjusted up or down to align with the Freezer door .
デバイスElectrolux Built-In Side-by-side Refrigeratorsの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Electrolux Built-In Side-by-side Refrigeratorsをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはElectrolux Built-In Side-by-side Refrigeratorsの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Electrolux Built-In Side-by-side Refrigeratorsの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Electrolux Built-In Side-by-side Refrigeratorsで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Electrolux Built-In Side-by-side Refrigeratorsを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はElectrolux Built-In Side-by-side Refrigeratorsの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Electrolux Built-In Side-by-side Refrigeratorsに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちElectrolux Built-In Side-by-side Refrigeratorsデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。