ElinchromメーカーDigital 3000 ASの使用説明書/サービス説明書
ページ先へ移動 of 16
Instructions for use Instructions for use Instructions for use Instructions for use Instructions for use POWER POWER POWER POWER POWER UNIVERSALITY UNIVERSALITY UNIVERSALITY UNIVERSALITY UNIVERSALITY TOTAL ASYMMETRY ASYMMETRY ASYMMETRY ASYMMETRY ASYMMETRY elinca sa switzerland www.
2 page Table of contents Table of contents Table of contents Table of contents Table of contents Safety notice 3 3 3 3 3 Control panel 4 4 4 4 4 Before you start 5 5 5 5 5 Technical data 6 6 6 6 6 Mai.
3 FLASH SYSTEMS STORE ELECTRICAL ENERGY IN CAPACITORS BY APPLYING HIGH VOLTAGE. FOR YOUR SAFETY, NEVER OPEN YOUR FLASHES. ONLY AN AUTHORISED SERVICE ENGINEER SHOULD OPEN OR ATTEMPT TO REPAIR THE UNITS.
4 1 . Mains inlet power socket 2. Mains fuse (16 AT, slow blow) 3. Charge speed selectors - slow charge - normal charge - fast charge 4. Mains switch 5. Photocell and IR-Receiver 6. Photocell on/off 7. Sync.-socket with security lock 8. Open flash with charge indicator 9.
5 1) Mains connection The unit is manufactured to run on 200-240 V, 50/60 Hz. Before connecting them for the first time, make sure that your mains supply and the rating set on the equipment (electrical specification plate) are compatible.
6 Display Ws f-stop Power 9 3000 (180.3) 1/1 8 1500 (128.3) 1/2 7 750 (90.3) 1/4 6 375 (64.3) 1/8 5 188 (45.3) 1/16 5** 95 (32.3) 1/32 with 2 lampheads 5*** 62 (22.7) 1/48 with 3 lampheads on mains 230 V- 50 Hz 1.8 - 10 s 0.8 - 4.5 s 0.7 - 3.5 s on mains 115 V- 60 Hz 2 - 11s 0.
7 Standard type 5 x 20 mm, 16 AT (tempered). Before exchanging a blown fuse, switch off the unit and remove mains cable. Depress and turn the fuse holder anti-clockwise 1/8th and remove it. If the new fuse blows immediately upon reconnection return the pack to an ELINCHROM service centre for a check-up.
8 N.B. For even less load on the power supply line use and jointly. The modelling lamps automatically extinguish when the generator is charging but illuminate when the charge cycle ends. When the indicator of the touch (12) is illuminated and will sound whenever a command has been accepted by the generator (useful when using the IR handset).
9 10. POWER INDICATOR «BLINKS» 8. TOT AL POWER 9. INDIVIDUAL POWER OUTPUT This display indicates the total power released through the lampheads. The variation is a single steps or if the touch is held it will run continuously. The first number indicates charges by full f-stop, the second number by 1/10 f-stop.
10 11. SWITCHABLE PHOTOCELL (SLAVE) 12. SYNCHRONISATION SOCKET 12. ACCESSORY SOCKET The Amphenol secure locking system with standard 5 m cable is retained. Longer cables may be used. N.B. Do not link ELINCHROM units by cable to other manufacturers sync outlets.
11 The modelling lamp will only function when the lamphead is switched on (note : there is an overheating control switch ON/OFF in the lamphead). - Simple ON/OFF with ON setting indicated.
12 14. LAMPHEADS ON/OFF 15. FUSES FOR LAMPHEADS 13. LAMPHEADS Important : When plugging in a lamphead connector, first push in the front part, then firmly press in the whole plug, the rear part being secured by the locking spring. Different modelling lamps require corresponding fuses.
13 16. PROTECTIVE PIREX DOME For use with standard halogen lamp GX 6.35 socket. Transparent, matt or yellow (400 ° K colour correction), can be fitted to all lampheads, except R heads (rectangular heads) for which clear or matt security filters are available.
14 18. LAMPHEAD COMPATIBILITY * 2000 Ws with MICRO series ** 3000 Ws with MICRO series MAXIMUM Compatible with : Digital 1500/3000 AS and MICRO AS ADAPTABLE 4000 Ws Digital S S4000 T4 T A4 A4 A Box Li.
15 Accessories overview Accessories overview Accessories overview Accessories overview Accessories overview Reflectors Reflectors Reflectors Reflectors Reflectors code code code code code Wide angle .
16 Visit our W eb site : www.elinchrom.com Elinca s.a E. Digital 3000 AS (73316) Printed in Switzerland.
デバイスElinchrom Digital 3000 ASの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Elinchrom Digital 3000 ASをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはElinchrom Digital 3000 ASの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Elinchrom Digital 3000 ASの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Elinchrom Digital 3000 ASで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Elinchrom Digital 3000 ASを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はElinchrom Digital 3000 ASの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Elinchrom Digital 3000 ASに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちElinchrom Digital 3000 ASデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。