Empire ProductsメーカーDV-25T-1の使用説明書/サービス説明書
ページ先へ移動 of 20
Page 1 INST ALLA TION INSTRUCTIONS AND OWNER'S MANUAL W ARNING: If not installed, operated and maintained in accordance with the man ufac tur er's ins truct ions , th is pr oduct cou ld expose you to substances in fuel or fr om fuel combustion which can cause death or serious illness.
131 17-9-0907 Page 2 SECTION P AGE Important Safety Information ......................................................................................................................3 V ent Kit Information .............................................
131 17-9-0907 Page 3 • Due to high temperatur es the appliance should be located out of traffic and away from furnitur e and draperies. • Children and adults should be alerted to the hazards of high surface temperatures and should stay away to avoid burns or clothing ignition.
131 17-9-0907 Page 4 Some people cannot smell well. Some people cannot smell the odor of the chemical put into the gas. Y ou must find out if you can smell the odorant in propane. Smoking can decrease your ability to smell. Being around an odor for a time can affect your sensitivity or ability to detect that odor .
131 17-9-0907 Page 5 REQUIREMENTS FOR MASSACHUSETTS For all side wall horizontally vented gas fueled equipment installed in every dwelling, building or structure used in whole or in part for residenti.
131 17-9-0907 Page 6 Introduction Al w a ys c on s u lt y ou r l o ca l B ui l di n g D e pa r t me n t r e ga r d in g regulations, codes or ordinances which apply to the installation of a direct vent wall furnace. Instructions to Installer 1. Installer must leave instruction manual with owner after installation.
131 17-9-0907 Page 7 Locating Gas Supply The gas line can enter the unit either through the floor or outside wall. The gas line opening should be made at this time. Location of the opening will be determined by the position of floor joists and the valve and union used for servicing.
131 17-9-0907 Page 8 1. In selecting a location for installation, it is necessary to provide adequate accessibility clearances for servicing and proper installation.
131 17-9-0907 Page 9 Installing W all Mounting Bracket Locate and cut wall opening. If there is insulation above the wall open- ing (air inlet tube) a barrier should be installed above the wall opening (air inlet tube) to prevent insulation from coming in contact with the air inlet tube.
131 17-9-0907 Page 10 Installing V ent Assembly Attention: Do not attempt to cut vent tubes. When you order appropriate vent kit for measured wall depth, the vent tubes will fit together . 1. Place provided caulking beneath the collar of the outside mounting plate.
131 17-9-0907 Page 1 1 Millivolt wall thermostats are specially designed for use on self-generating systems. They should never be used on line or low voltage A.C. circuits. Figure 9 Interior W all - The thermostat can also be installed on an inside wall away from the furnace but in the same room.
131 17-9-0907 Page 12 FOR YOUR SAFETY READ BEFORE LIGHTING W ARNING: If you do not follow these instructions exactly , a fir e or explosion may result causing property damage, personal injury or loss of life. A. This appliance has a pilot which must be lighted by hand.
131 17-9-0907 Page 13 The correct flame will be almost horizontal, blue and will extend past the thermopile 1/4" (6mm). The flame will surround the thermopile just below the tip. On propane (LP-gas) slight yellow might occur where the pilot flame and burner flame meet.
131 17-9-0907 Page 14 1. Lit match goes out as it enters lighter port. a. Certain wind conditions will blow out match. Ignite match, and as it flares, thrust match through opening. b. Open nearby door or window and relight pilot. 2. Pilot flames but goes out when knob is r eleased.
131 17-9-0907 Page 15 PLEASE NOTE: When ordering parts, it is very important that part number and description of part coincide. USE ONL Y MANUF ACTURER'S REPLACEMENT P AR TS. USE OF ANY OTHER P AR TS COULD CAUSE INJUR Y OR DEA TH. Parts can be ordered only through your service person or dealer .
131 17-9-0907 Page 16 P AR TS VIEW.
131 17-9-0907 Page 17 OPTIONAL BLOWER DRB-1 Installing Optional DRB-1 Blower 1. Remove casing from front and heat shield 2. When facing appliance, insert blower assembly into the left section of the casing (adjacent to the combustion chamber). 3. Route cord set through ope ning in casing in bottom.
131 17-9-0907 Page 18 Cleaning The blower wheel will collect lint and could require cleaning once a year . If the air output decreases or the noise level increases, it indicates a dirty wheel. Complete removal of the wheel and scrubbing it with a brush under flowing water is recommended.
131 17-9-0907 Page 19 SER VICE NOTES.
131 17-9-0907 Page 20 Empire Comfort Systems, Inc. 918 Freeburg A ve. Belleville, IL 62220 PH: 618-233-7420 or 800-851-3153 F AX: 618-233-7097 or 800-443-8648 info@empirecomfort.
デバイスEmpire Products DV-25T-1の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Empire Products DV-25T-1をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはEmpire Products DV-25T-1の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Empire Products DV-25T-1の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Empire Products DV-25T-1で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Empire Products DV-25T-1を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はEmpire Products DV-25T-1の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Empire Products DV-25T-1に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちEmpire Products DV-25T-1デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
