Empire ProductsメーカーGWT-25-2の使用説明書/サービス説明書
ページ先へ移動 of 20
12425-7-0406 Page 1 INST ALLA TION INSTRUCTIONS AND OWNER'S MANUAL GRA VITY VENTED SINGLE W ALL FURNACE MODEL GWT -25-2(SG, RB) GWT -35-2(SG, RB) EFFECTIVE DA TE APRIL 2006 W ARNING: If the information in this manual is not followed exactly , a fire or explosion may result causing pr operty damage, personal injury or loss of life.
Page 2 12425-7-0406 T ABLE OF CONTENTS SECTION P AGE Important Safety Information ................................................................................................. 3 Safety Information for Users of LP Gas ..............................
12425-7-0406 Page 3 • DO NOT put anything around the furnace that will obstruct the flow of combustion and ventilation air . • DO keep the appliance area clear and free fr om combustible material, gasoline and other flammable vapors and liquids.
Page 4 12425-7-0406 Some people cannot smell well. Some people cannot smell the odor of the chemical put into the gas. Y ou must find out if you can smell the odorant in propane. Smoking can decrease your ability to smell. Being around an odor for a time can affect your sensitivity or ability to detect that odor .
12425-7-0406 Page 5 Model GWT -25 GWT -35 Input BTU/HR (KW/H) 25,000 (7.3) 35,000 (10.3) Height 66 1/8" (1679mm) 66 1/8" (1679mm) W idth 16" (406mm) 16" (406mm) Depth 6" (152m.
Page 6 12425-7-0406 Note: No vent equipment supplied with furnace. 4" Oval (all parts purchase locally) 1. T ype B-1 oval pipe 2. Single story type B-1 gas vents require a baseplate and one pair of ceiling plate spacers.
12425-7-0406 Page 7 Check all local codes for requirements, especially for the size and type of gas supply line required. Recommended Gas Pipe Diameter Pipe Length Schedule 40 Pipe T ubing, T ype L (feet) Inside Diameter Outside Diameter Nat. L.P . Nat.
Page 8 12425-7-0406 1. In selecting a location for installation, it is necessary to provide adequate accessibility clearances for servicing and proper installation. 2. Clearances to combustible surfaces are 4" (102mm) from sides, 12" (305mm) to top, 1 1/2" (38mm) from floor .
12425-7-0406 Page 9 62 1/4” (1581 mm) 14 ½” (368 mm) Figure 2 66 1/8” (1679mm) W ALL OPENING Figure 3 FINISHING INSTRUCTIONS Plastering (Figure 4) In new construction use only plain (not perforated) gypsum lath around furnace and vent pipe so that plaster "Keys" will not project into wall space.
Page 10 12425-7-0406 Figure 6 IMPOR T ANT — A void securing too tightly and disturbing the inner casing. Do not try to force furnace into a wall opening which is smaller than specified dimension. OUTER CASING (Figure 6) 1. Align 1 3/4" slot on casing bracket with bottom screw hole on inner casing.
12425-7-0406 Page 1 1 THERMOST A T LOCA TION (SG MODELS) CAUTION — Do not run wire behind flanges of Header Plate or in any location where it might be damaged. Millivolt wall thermostats are specially designed for use on self- generating systems. They should never be used on line or low voltage A.
Page 12 12425-7-0406 FOR YOUR SAFETY READ BEFORE LIGHTING W ARNING: If you do not follow these instructions exactly , a fire or explosion may result causing property damage, personal injury or loss of life. A. This appliance has a pilot which must be lighted by hand.
12425-7-0406 Page 13 VENT SAFETY SHUT OFF SYSTEM This appliance must be properly connected to a venting system. This appliance is equipped with a vent safety shutoff system.
Page 14 12425-7-0406 GENERAL All furnaces have been fire-tested to check for proper operation. This includes main burner flame, pilot flame, and gas control operation. If the furnace fails to function on initial installation, it is advisable to re-check the following: 1.
12425-7-0406 Page 15 USE ONL Y MANUF ACTURER'S REPLACEMENT P ARTS. USE OF ANY OTHER P ARTS COULD CAUSE INJUR Y OR DEA TH. A TTENTION: When ordering parts, it is very important that part number and description of part coincide. Index Part No. Number Description Index Part No.
Page 16 12425-7-0406 P AR TS VIEW 8 27 9 12 11 14 13 10 15 16 20 18 19 21 26 17 22 24 25 7 3 1 2 5 4 6 23.
12425-7-0406 Page 17 Index Part No. Number Description 1 GW -130 Remote Bulb Control Kit 2 R-1224 Remote Bulb Control 3 R-2499 W ire Assembly 4 R-1162 Control Knob 5 R-1720 Plastic Clip (3 Required) 6 R-1223 Instructions 7 R-1578 No. 6-32 x 1/4" (6mm) Screw (2 Required) Caution: Remote bulb wire routing is important.
Page 18 12425-7-0406 Installing Blower Using Three-Pr ong Plug 1. Install furnace according to Installation Instructions and Owner's Manual. 2. Refer to Drawing for measurements to locate (2) mounting holes on wall surface above furnace. On Solid W all 3.
12425-7-0406 Page 19 Fan Control The automatic fan control is located on the bottom of the blower assembly . The fan control is a nonadjustable, automatic type. The fan control will require between 3 and 7 minutes of main burner operation before the fan control "closes" and activates the blower .
Page 20 12425-7-0406 SER VICE NOTES Empire Comfort Systems, Inc. Nine Eighteen Freeburg A ve. Belleville, Illinois 62220-2623 PH: 1-618-233-7420 PH: 1-800-851-3153 F AX: 1-618-233-7097 F AX: 1-800-443-8648 E-MAIL: info@empirecomfort.com WEB SITE: www .
デバイスEmpire Products GWT-25-2の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Empire Products GWT-25-2をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはEmpire Products GWT-25-2の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Empire Products GWT-25-2の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Empire Products GWT-25-2で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Empire Products GWT-25-2を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はEmpire Products GWT-25-2の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Empire Products GWT-25-2に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちEmpire Products GWT-25-2デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
