Encore electronicメーカーENNUS1の使用説明書/サービス説明書
ページ先へ移動 of 30
ENNUS1 USB-OVER-NETWORK SERVER User Manual 0.
Table of Contents CHAPTER1 INTRODUCTION .......................................................................................................... 2 CHAPTER2 PRODUCT OVER VIEW ...........................................................................
Chapter1 Introduction Thank you for purchasing Encore ENNU S1 USB-OVER -NETWORK SERVER (in the f o l l o w i n g r e f e r r e d t o a s “ E N N U S 1 S e r v e r ” ) .
Chapter2 Product Overview 2.1 Package Contents V erify that nothing is missing from the package by using the checking list below . Please contact your retailer if an y item is missing or damaged.
Chapter3 Basic Installation 3.1 Connecting the Hardware 1. Make sure that y our USB devices ar e switched off and that the ENNUS1 Server’ s power adapter is disconnected. 2. Connect the USB devices to the USB ports. 3. Connect the ENNUS1 Server to the network with a twisted-pair category 5 cable, 10base T or 100base TX.
3.2.4 Server Names and Server Name Rules The default server name of the Serv er is “ENNUS1” . If you hav e multiple Servers in your local area network, to av oid using the same server names you hav e to change the server names by using t h e Control Center .
5. Click the “CONFIG” button and enter the ENNUS1 Serv er’s administrator (default: admin) and password (default: admin). 6. After you login successfully , the “general setting” web page appears.
7. Click the button corresponding to your ch oice of IP setting method (static or dynamic using DHCP). When assigni ng a static IP address you also have to define Subnet Mask and Default Gatew ay . If you choose Automatically get IP by DHCP , you can use desired DNS by c licking the Manual DNS button and manually assigning a DNS.
Chapter4 Using the ENNUS1 Server 4.1 Introduction The goal of this product is to provide connectivity to USB devices from a single serv er . A new technology , “NetUSB” , has been develo ped to achiev e this goal. “NetUSB” is a “USB over IP” technology that tr ansparen tly redirects all USB packets to a T CP/IP network channel.
Y ou must change the IP address (or using DHCP) of the ENNUS1 serv er so that the ENNUS1 server and y our PC are in the same subnet. T o do this, please double-click on the ENNUS1 server , and the following window will appear . Change the IP setting to make ENNUS1 serv er and your PC within the same subnet.
C. When the installation progr am asks yo u to plug-in the USB device, run the “Control Center” . D. In the Control Center , click t he ENNUS1 server that has the desired USB device attached. E. Click the desired USB device as in the following figure.
4.5 Using the ENNUS1 Server A. In the Control Center , click the ENNUS1 server that has the desired USB device attached. B. Click the desired USB device. C. Click the “Connect” button. Then the message “Manually Connect by your_computer_name ” will appear .
4.6 Auto-Connect Printer The method described in section 4.5 is called “manual connect” , which means users must manually connect and disconnect the US B device before and after using that device, otherwise nobody else can connect that device.
The following window will appear . D. Choose the desired printer . The desired pr inter must be the Windows printer (this is a logical printer) that matches the prin ter attached on the ENNUS1 server (this is a physical printer). Then click the “ Apply” button.
F. T r y to issue a print job to the desired printer . The Cont rol Center will automatically do a connect operation. The print job will be issued to that printer . G. Even if you ha ve properly setup an auto -connected printer , the Control Center must be running (in the bac kground) while a print job is i ssued.
C. Click the “Network Scanner” button. Then yo u can see that the Control Center will automatically do a “connect” operatio n. The following window will appear . D. Choose one of TWAIN or WIA item. Click “OK” . The following window will appear .
E. F o llow the usual steps to do scanning. F. After the scanning, close the “ Auto-Connect Sca nner” window . At this moment, Control Center will automa tically do a disconnect. 4.8 USB Storage When you connect a USB stor age, as in the fo llowing picture, a new disk will appear on your PC.
Y ou can see the stor age ic on in the system tray . Use the new disk as a regular disk. When y ou are ready to disconnect the disk, click the stor age icon in the system tray an d choose “Safely remov e USB Mass Stor age Device” to remove the USB stor age, as the following figure.
At this moment, the user on the TEST1 computer will see the following window , indicating that another computer – TEST2 is requesting to use the HP printer .
Chapter5 The Control Center This chapter describes how to use the Control Center . 5.1 Installing Control Center 1. Insert the included CD into the personal computer. The Autorun screen as in the following should appear. 2. Click Install Application button.
5.2 Using the Control Center Y ou can use the following tools to help y ou use the ENNUS1 server: Configure Server : go to the server’ s web pages to configure the highlighted ENNUS1 server . Auto-Connect Printer : set auto-connect printer .
Chapter6 The ENNUS1 Server’s Web Pages 6.1 Introduction The ENNUS1 server runs the http server on T CP port: 80. Us ers may use the web pages to see the ENNUS1 Server’ s system status and configure the ENNUS1 Server . 6.2 Using the ENNUS1 Server’s Web Pages 6.
6.2.2 Setting up ENNUS1 Server Configuration T o set up the ENNUS1 Server configur ation, click on the “C ONFIG” icon and then the system will request user to enter administrator (default: admin ) and password (default: admin ) to login.
Maintenance If you want to restore factory default v alues of the ENNUS1 Server or upgr ade new firmware, you can use the Maintenance tool. 5 Restart: click “Y es” button to restart (reboot) the ENNUS1 Serv er . 5 Factory Default: click this button, the ENNUS1 Server will restore factory default values.
24.
Chapter7 Troubleshooting This chapter provides useful information to help yo u resolve diffic ulties that you ma y experience with your ENNUS1 Server . F aul t symptoms, possible causes, and remedial actions are provided within a quick reference table.
Chapter8 Restore Factory Defaults Y ou ma y restore the ENNUS1 Server’ s defa ult parameters by one of the following methods. 8.1 Using the ENNUS1 Server’s Web Pages 1. Go to the ENNUS1 Server ’ s web page and click CONFIG 2. Enter administra tor (default: admin ) and password (default: admin ).
8.3 Default Parameters List Server Information z Server Name: ENNUS1 TCP/IP z Automatically get IP by DHCP: Enabled - Manual DNS: None (Disabled) . z Static IP: Disabled - IP Address: 192.
Chapter9 Upgrade Firmware This chapter describes how to upgrade firm w are. Please follow one of the following methods: Method A: Using the ENNUS1 Server’s Web Pages Please refer to section 6.2.2 for details. Method B: Using the Init Button and the TFTP Client 1.
Chapter10 The Init Button The Init button is used for maintenance: Simultaneously press Init button and turn on (by plugging in the power adaptor) th e ENNUS1 Server until the USB LED blinks.
デバイスEncore electronic ENNUS1の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Encore electronic ENNUS1をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはEncore electronic ENNUS1の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Encore electronic ENNUS1の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Encore electronic ENNUS1で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Encore electronic ENNUS1を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はEncore electronic ENNUS1の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Encore electronic ENNUS1に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちEncore electronic ENNUS1デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。