EnGenius TechnologiesメーカーIEEE 802.11b Outdoor Wireless Client Bridgeの使用説明書/サービス説明書
ページ先へ移動 of 27
IEEE 802.11b Outdoor Wireless Client Bridge User Manual November 03, 2004 Version 1.00 Before operating the unit, please read this manual thoroughly, and retain it for future reference. Version 1.02 i ■ Contents CHAPTER 1. INTRODUCTION .............
Version 1.02 ii 5.1 S YSTEM I NFORMATION ............................................................................ 38 5.2 S TATISTIC I NFORMATION ........................................................................ 39 5.3 S ITE S URVEY ........
Version 1.02 2 1.4 System Requirements Installation of the Outdoor Wireless Client Bridge requires the following: 1. A Windows-based PC/AT compatible computer or Ethernet data device with an available RJ-45 Ethernet port to run the configuration program or wi th TCP/IP connection to the Ethernet network.
Version 1.02 4 2.2 Locate the Wireless client bridge and Inline Power Injector Ports Interface on the Wireless client bridge Unit 9 Ethernet Port 1 for connecting the RJ-45 CAT-5 Ethernet cable. 9 RS-232 Console Port 2 for connecting the 1.8m RS-232 null modem console cable.
Version 1.02 6 Figure 2.2.1 You can also mount the Wireless client bridge to the mast as shown in Figure 2.2.2 . Figure 2.2.2 Version 1.02 7 2.3 Preparing Installation Before installing Wireless client bridge for the outdoor application in a hard- to-reach location, we recommend to conf igure and test all the devices first.
Version 1.02 8 NOTE: This connection is required for setting up initial configuration information. After configurati on is completed, the RS-232 null modem console cable shall be removed, and run a cross-over Ethernet cable from Data Input Port to PC, or a straight Ethernet cable to LAN connection, e.
Version 1.02 10 2.4.3 Login into the Web Interface The Wireless client bridge supports a ccess to the configuration system through the use of an HTTP Interface. Web Configuration Before configuring Wireless client bridge, user needs to know the IP Address assigned to the unit.
Version 1.02 12 Step 3 Enter “ root ” in the User Name and the Passw ord fields, and click OK to enter the web configuration user interface screen as shown below. Web Configuration Structure The web configuration user interface is grouped into a tree structure, and contains the following settings or information.
Version 1.02 14 IP Use MAC Addr. You can choice Enable or Disable. If you choice Enable , it will set IP = 10.X.X.X that used to last 3 MAC Address ID. For example : MAC Addr = 00:47:55:43:43:49 => IP = 10.67.67.73(43hex=67decimal) If you choice Disable you need setting Bridge IP Address Information .
Version 1.02 16 2.4.7 Upgrade the Firmware Setup your TFTP Serv er The Trivial File Transfer Protocol (TFTP ) Server allows you to transfer files across a network.
Version 1.02 18 shown below. Step 2 Press < Esc > keystroke to reboot the Wireless client bridge. Press < x > key during the boot process, and it will display prompt character NetARM> as the figure shown in the next page. Step 3 Press “ h ” keystroke, it will display related commands as the figure shown below.
Version 1.02 20 2.4.8 Back-up the Wireless clie nt bridge’s Configuration Files After configuring Wireless client bri dge, user can back-up the configuration files. User can upload the latest back-up files and recover the Wireless client bridge configuration to the se ttings specified in the back-up files.
Version 1.02 22 Chapter 3. Network T opologies This chapter describes several main types of installations implemented by using the Outdoor Wireless System commonly . This is by no means intended to be an exhaustive list of all possible configurations, but rather shows examples of some of the more common implementations.
Version 1.02 24 3.2 Wireless Client Router-to-Central Wireless Bridge Step 1 Set the COU to perform a bridge ( bridge IP address: 192.168.2.1 ). Step 2 Set Wireless parameters on COU: Channel (1) and SSID (w ireless) . Step 3 Set the ROU to perform a Router ( Wireless Interface IP: 192.
Version 1.02 26 3.4 Wireless Client Router-to-Central Wireless Router Step 1 Set the COU to perform a Wireless Router ( Wireless Interface IP: 192.168.1.1, Ethernet Interface IP : 192.168.2.1, default route: 192.168.2.254 ). Step 2 Set Wireless parameters on COU: Channel (1) and SSID (w ireless) .
Version 1.02 28 Chapter 4. Network Parameters 4.1 IP Configuration Wireless Client Bridge Step 1 Enter the IP Address manually into the Bridge IP Address field. Step 2 Use Bridge IP Address setting to assign or change the bridge’s IP address. Step 3 Click FINISH at the bottom of this page to complete the modification of IP address.
Version 1.02 30 4.2.2 Configure Trap Host Pool The Trap Host Pool has five entries. 1. To modify a entry, click the sele ct button beside the entry index number and click Modify . The configuration page appears as following figure. 2. Specify the Version, IP Address and Community field.
Version 1.02 32 4.3 Configure Wireless related parameters Step 1 Select “ /General Config/Wireless” and the Wireless LAN information page appears as the figure shown below. Step 2 In the Wireless LAN information page, set the following parameters suitable for your radio network.
Version 1.02 34 numbers 0 through 9 and the letters A through F. The 40-bit WEP keys can contain any combination of 10 of these characters; the 128-bit WEP keys can contain any combination of 26 of these characters. The letters are not case-sensitive.
Version 1.02 36 4.4.2 Administration Step 1 Click Utility , Administration. The following figure shows the Utility – Administration page. 9 Supervisor Account. Change the supervisor’s user name & password in the Supervisor Account field, and Click FINISH to take effect on the previous configuration changes.
Version 1.02 38 5.1 System Information By selecting “ Running Status / Sy stem Info ”, enter the System Information page as the figure shown below. In this page, user can find the system information and most of the running parameters. Version 1.02 39 5.
Version 1.02 40 5.3 Site Survey By selecting “ Running Status / Site Survey ”, enter the Site Survey page as the figure shown below In this page, user can click REFRESH find the AP near Wireless client bridge. This statistic table includes the following information.
Version 1.02 42 Chapter 6. S pecifications 6.1 Hardware Specifications General Radio Data Rate 11, 5.5, 2 and 1 Mbps, Auto Fall-Back Client Interface 10/100Base-T Ethernet Range (Open environment) 300m @ 11 .0 Mbps 400m @ 0 5.5Mbps 500m @ 0 2 .0 Mbps 800m @ 0 1 .
Version 1.02 44 6.2 Software Specifications Protocol TCP/IP DHCP Client 802.1d T ransp arent Bridging Security 64-/128-bit WEP encryption MAC address based access control Management Web-based Manager Console (RS-232) configuration SNMP v1 SNMP MIB-II Private MIB Firmw are upgrade TFTP (T rivial FTP) Xmodem, 1K Xmodem Zmodem Version 1.
Version 1.02 46 7.1.2.2 Table of SNMP Trap Community Host Pool Parameter Description Default Value Index 1 Version1 Index 2 Version2 Index 3 --- Index 4 --- Index 5 Version Select or disable the SNMP Version Version 1: MIB1 Version 2: MIB2 --- Index 1 192.
Version 1.02 48 7.2 Utility 7.2.1 Software Upgrade Parameter Description Default Value TFTP Server IP Address Specify the IP address of the TFTP server to upgrade the firmware of the RB 192.168.2.100 Program Image SUSW.Bin Upgrade Filename Web Image SUFS.
Version 1.02 50 Professional Installation Per the recommendation of the FCC, the installation of high gain directional antenna to the system, which are intended to operated solely as a point-to- point system and whose total power exceeds +30dBm EIRP, require professional installation.
デバイスEnGenius Technologies IEEE 802.11b Outdoor Wireless Client Bridgeの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
EnGenius Technologies IEEE 802.11b Outdoor Wireless Client Bridgeをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはEnGenius Technologies IEEE 802.11b Outdoor Wireless Client Bridgeの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。EnGenius Technologies IEEE 802.11b Outdoor Wireless Client Bridgeの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。EnGenius Technologies IEEE 802.11b Outdoor Wireless Client Bridgeで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
EnGenius Technologies IEEE 802.11b Outdoor Wireless Client Bridgeを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はEnGenius Technologies IEEE 802.11b Outdoor Wireless Client Bridgeの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、EnGenius Technologies IEEE 802.11b Outdoor Wireless Client Bridgeに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちEnGenius Technologies IEEE 802.11b Outdoor Wireless Client Bridgeデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
