Allen & HeathメーカーXone 22の使用説明書/サービス説明書
ページ先へ移動 of 24
1 USER GUIDE Publication AP7402.
2 Limited One Y ear W arranty This product is warranted to be free from defects in materials or workmanship for period of one year from the date of purchase by the original owner. To ensure a high level of performance and reliability for which this equipment has been designed and manufactured, read this User Guide before operating.
3 P A CKED ITEMS Check that you have received the f ollowing: Safety Sheet Important ! R e a d t h i s s h e e t before starting. Retain for future reference.
4 CONTENTS Congratulations on purchasing the A llen & Heath Xone:22 performance DJ mixer. To ensure that you get the maximum benefit from the unit please spare a few minutes familiarizing yourself with the controls and setup procedures outlined in this user gu ide.
5 CONNECTION DIA GRAM.
6 INTR ODUCTION T O THE XONE:22 The Xone:22 has been designed to m eet the requirements of those users who want a high quality, affordable, co mpact DJ mixer. Its feature set has been kept to the essential elements needed to produce professional quality mixes, without compromising the design by adding superfluous gimmicks.
7 INPUT CHANNEL CONTR O LS Input level control Adjust so that the aver- age music level lights the 0 LED on the meter, with the beats lighting the +3 t o + 6 L E D .
8 MASTER CONTROLS FX loop on switch Press this switch to activate the external effect loo p. Leave switched off if an ex ternal effects unit is not con nected Master output Level Sets the signal level.
9 MASTER CONTROLS continued Headphone level Sets the level of the hea d- phone outpu t. Warning! Very high level can cause hearing damage! Cue/Master Switch In the up positio n (Cue) the headphones will moni tor the channel signal before the fad- ers, and the meters will display the pre fade channel signal level.
10 REAR P ANEL CONNECTIONS Phono inputs For connection to turntable s only; this input has RIAA equalization for moving magnet cartridges. Note: these inputs can be converted to Li ne with internal jumper links Effects SND output Connect this output to the input of an ex- ternal effects unit.
11 FR ONT P ANEL CONNECTIONS Microphone EQ 2 band EQ for adjust ing the tonal balance of the DJ mic Microphone input Professional XLR balanced mic input. Use a low impedance dynamic hyperca rdioid Mic for best results. Microphone Level Adjusts the signal lev el of the mic input.
12 FIL TER REFERENCE The VCF Filters A voltage controlled filter is an audio filter where the cut-off frequen cy is altered by a DC control voltage rather than a variable resist or. This produces a much wider operating range and more control over the filter resp onse to create unlimited combinations of tonal effect.
13 It is most important that the system level sett ings are correctly set. It is well known that many DJs push the leve l to ma ximum with meters peaking hard in the belief that they are getting the best from the system.
14 The connection to earth (ground) in an audio system is important for two reasons: SAFETY - To protect the operator from high voltage electric shock, and AUDIO PERFORMANCE - To minimise the effect of earth (ground) loops which result in audible hum and buzz, and to shield the audio signals from interference.
15 SER VICING AND JUMPER SETTINGS To change the Phono input to line Remove the front panel as outl ined before. You need to locate and remove the two bla ck jumper links on the inp ut PCBs in the location shown. It is a good idea to leave the jumper links attached to one pin so that they can be refitted at a future date.
16 REPLA CEMENT P AR TS USER-REPLA CEABLE P AR TS AB8172 POT NUT BK (16 places - under knobs) AJ7464 PUSH BUTTON SQUARE RED 5MM AJ5325 FILTER / FX BTN (3 places) AJ5320 XONE FADER KNOB (3 places - fad.
17 No sound from mixer Check that the unit is powered on, and that an audio signal is connected to a channel input. Check that the PHONO/LINE switch is in the correct po sition for the type of music source connected, (P HONO for turntables, LINE for CD players.
18 SPECIFICA TIONS Connections Inputs Connection Impedance Nominal Level Maximum Level Phono RCA 47K/330pF 7mV-100mV Line RCA 20K ohm -10 to +18dBu FX RTN RCA 10K ohm 0 to +18dBu Mic XLR <2K ohm -4.
19 + FADER CUE/ MASTER LF MF HF FX LOOP ON PHON ES -2d Bu -2dBu CUE/MI X METE R CH2/RI GHT MA STE R METE R PHO NO L R LINE L + DC FADER CUE MIX CH 1 /L EFT MA STER X: FX SEN D FX MIX X: FX S EN D X:FX.
20.
21 PR ODUCT REGISTRA TION Registering your product Please go to www.allen-heath.com/register.asp and regist er your product’s serial number and your details. By registering with us and becoming an official Regi stered User, you will ensure that any warranty claim you might make is actioned quickly an d with the minimum delay.
22.
23.
24.
デバイスAllen & Heath Xone 22の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Allen & Heath Xone 22をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはAllen & Heath Xone 22の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Allen & Heath Xone 22の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Allen & Heath Xone 22で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Allen & Heath Xone 22を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はAllen & Heath Xone 22の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Allen & Heath Xone 22に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちAllen & Heath Xone 22デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
