Epsonメーカー1500の使用説明書/サービス説明書
ページ先へ移動 of 18
EPSON ® 1000/1500 Setup Guide.
Contents Setup 1 Unpacking ............................. 1 2 Installing the imaging cartridge ................. 1 3 Loading paper ........................... 4 4 Attaching the power cord ..................... 5 5 Test printing ........................
This booklet is to help you set up your printer and begin printing quickly. It also gives you instructions for routine maintenance. If you need detailed information on printer use or if you have problems printing, see your Reference Guide. Epson is a registered trademark of Seiko Epson Corporation.
Setup 1 Unpacking 1. Remove the accessories and printer from the shipping carton. 2. Set the printer on a flat, stable surface. 3. Take the packaging off the printer and the other items and store it for future use. Note: The printer weighs about 10 kg (22 lbs) and should be lifted with care.
2. While holding the imaging cartridge horizontally, gently shake it a few times to distribute the toner evenly. 3. Set the imaging cartridge on a clean, flat surface. Firmly grip the tab on the left side of the imaging cartridge. Pull the clear seal all the way out with firm, even pressure as shown.
4. Insert the imaging cartridge into the printer by placing the pins on each side of the cartridge into the grooves inside the printer. Slide it gently into the opening until it stops. 5. Gently press down on the printer cover until it clicks shut. CAUTION: Never transport the printer with the imaging cartridge installed.
3 Loading paper 1. 2. 3. 4. 5. Fan a stack of letter-size paper and even up the edges. Open the paper cover located on the top front of the printer. Adjust the paper guides inside the paper bin to match the size of the paper. Load a stack of paper (up to 150 sheets) into the paper bin.
4 Attaching the power cord 1. Make sure the power switch at the top right of the printer is turned off. 2. Insert the power cord into the back of the printer. Then plug the other end into a properly grounded outlet. 5 Test printing 1. 2. 3. 4. 5. Make sure the imaging cartridge is installed.
6 Connecting the printer to the computer You can connect up to three computers (two for the ActionLaser 1000) to your printer at the same time. If you are connecting more than one computer, see “Sharing Your Printer” in the Reference Guide.
Note: If you connect your printer to a serial or optional interface, you my need to change some of the printer’s settings. See the SelecType INTERFACE option in Chapter 4 of the Reference Guide.
8 Setting up your software Choosing the printer emulation Your printer has several resident printer emulations: HP LaserJet III (3/P/Si), Epson LQ, Epson FX, and Epson GL/2 for the ActionLaser 1500; HP LaserJet IIP (LJ-2P), Epson LQ, and Epson FX for the ActionLaser 1000.
If none of the above printers is listed, select any printer model that uses the HP Printer Command Language (PCL). For the GL/2 emulation on the ActionLaser 1500, you can print graphic data using the HP GL/2 commands or some HP GL commands. See Appendix B in the Reference Guide.
10 setup.
Maintenance Replacing the Imaging cartridge The imaging cartridge prints up to 6,000 pages depending upon the complexity of your print jobs. If your printed images become faint, enter the SelecType Level 2 TONER option to find out approximately how much toner remains in the imaging cartridge.
2. Gently open the printer cover and remove the imaging cartridge by pulling it toward you. 3. Dispose of the imaging cartridge with nonburnable items. e CAUTION: Do not turn the imaging cartridge upside down. Do not expose the imaging cartridge to light any longer than necessary.
5. Set the imaging cartridge on a clean, flat surface. Firmly grip the tab on the left side of the imaging cartridge. Pull the clear seal all the way out with firm, even pressure as shown. 6. Insert the imaging cartridge into the printer by placing the pins on each side of the cartridge into the grooves inside the printer.
7. Next you reset the TONER setting. Three messages flash in rotation on the display: NEW CARTRIDGE? YES, PRESS RESET NO, PRESS CONTINUE. 8. Press RESET to change the TONER setting to full. 9. Gently press down on the printer cover until it clicks shut.
Feed or paper jam When the printer stops printing and the FE E D JAY or PAPER JAM message appears, follow these steps: 1. Open the paper cover. Carefully remove all the paper in the paper bin along with any sheets that have fed part way into the printer.
デバイスEpson 1500の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Epson 1500をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはEpson 1500の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Epson 1500の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Epson 1500で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Epson 1500を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はEpson 1500の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Epson 1500に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちEpson 1500デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。