Epsonメーカー36-075の使用説明書/サービス説明書
ページ先へ移動 of 21
INSTRUCTION MANUAL 10" Compound Power Miter Saw (Model 36-075) P ART NO. 899908-0010 Copyright © 2000 Delta Machinery ESP AÑOL: PÁGINA 21 T o learn more about DEL T A MACHINER Y visit our website at: www .deltamachinery .com. For Parts, Service, W arranty or other Assistance, please call 1-888-848-5175 ( In Canada call 1-800-463-3582).
2 SAFETY RULES W oodworking can be dangerous if safe and proper operating pr ocedures ar e not followed. As with all machinery , there ar e certain hazards involved with the operation of the pr oduct. Using the machine with respect and caution will considerably lessen the possi- bility of personal injury .
3 3 ADDITIONAL SAFETY RULES FOR MITER SA WS 1. USE ONL Y CROSS-CUTTING SAW BLADES. WHEN USING CARBIDE TIPPED BLADES, MAKE SURE THEY HA VE A NEGA TIVE HOOK ANGLE.
4 UNP ACKING 1. Remove the miter saw and all loose items from the carton. IMPORT ANT : DO NOT LIFT THE MITER SAW BY THE SWITCH HANDLE AS THIS MA Y CAUSE MISALIGNMENT . AL WA YS LIFT THE MACHINE BY THE BASE OR CARR YING HANDLE . Fig. 2 illustrates the machine and all loose items after they have been removed fr om the carton.
5 Fig. 6 Fig. 7 Fig. 8 F ASTENING MACHINE TO SUPPORTING SURF ACE Fig. 9 MOVING CUTTINGHEAD TO THE UP POSITION 1. Push down on switch handle (A) Fig. 6, and pull out cuttinghead lock knob (B). 2. The cuttinghead (C) can then be moved to the up position, as shown in Fig.
6 CONNECTING SA W TO POWER SOURCE POWER CONNECTIONS A separate electrical circuit should be used for your tools. This cir cuit should not be less than #12 wire and should be protected with a 20 Amp time lag fuse.
7 7 7 Use proper extension cor ds. Make sure your extension cord is in good condition and is a 3-wir e extension cord which has a 3-prong gr ounding type plug and a 3-pole receptacle which will accept the tool’ s plug. When using an extension cord, be sur e to use one heavy enough to carry the current of the saw .
8 OPERA TING CONTROLS AND ADJUSTMENTS Fig. 14 Fig. 13 ST AR TING AND STOPPING MACHINE T o start the machine, depress switch trigger (A) Fig. 13. T o stop the machine, release the switch trigger . This miter saw is equipped with an automatic electric blade brake.
9 Fig. 15 Fig. 16 ROT A TING T ABLE FOR MITER CUTTING Y our miter saw will cut any angle from a straight 90 degree cut to 47 degr ees right and left. Simply loosen lock handle (A) Fig. 15, one or two tur ns, depress index lever (B) and move the control arm to the desir ed angle.
10 Fig. 19 Fig. 20 REAR SUPPOR T/CARR YING HANDLE A rear support bar (A) Fig. 19, is pr ovided to prevent the miter saw fr om tipping to the rear when the cut- tinghead is returned to the up position after a cut has been made. For maximum support the bar (A) should be pulled out as far as possible.
11 Fig. 21 Fig. 22 Fig. 23 Fig. 24 ADJUSTING BLADE P ARALLEL TO T ABLE SLOT 1. DISCONNECT THE SAW FROM THE POWER SOURCE. 2. Lower the cutting arm. The saw blade (A) Fig. 21, should be parallel to the left edge (B) of the table opening. 3. If an adjustment is necessary , loosen thr ee screws (C) Fig.
ADJUSTING 90 AND 45 DEGREE BEVEL STOPS 1. DISCONNECT THE SAW FROM THE POWER SOURCE. 2. Loosen bevel lock handle and move the cutting arm all the way to the right, then tighten the bevel lock handle. 3. Using a square (A) Fig. 25, place one end of the square on the table and the other end against the blade.
13 Fig. 29 LOCKING CUTTINGHEAD IN THE DOWN POSITION When transporting the saw , the cuttinghead should always be locked in the down position. This can be accomplished by lowering the cutting arm (A) Fig. 29, and pushing in plunger (B) until other end of plunger (B) engages with hole in cutting arm.
14 Fig. 31 Fig. 32 Fig. 33 Fig. 34 AUXILIAR Y WOOD FENCE WARNING: When performing multiple or repetitive cut-off operations that r esult in small cut-off pieces, one inch or less, it is possible for the saw blade to catch the cut-off pieces and pr oject them out of the machine or into the blade guard and housing, possibly causing damage or injury .
15 Fig. 35 Fig. 36 CUTTING ALUMINUM Aluminum extrusions such as used for making aluminum screens and storm windows can easily be cut with your compound miter saw .
16 Fig. 39 Fig. 40 Fig. 41 Fig. 42 CUTTING CROWN MOULDING One of the many features of your saw is the ease of cutting crown moulding.The following is an example of cutting both inside and outside corners on 52/38 degree wall angle crown moulding.
17 Fig. 45 Fig. 46 MAINTENANCE CHANGING THE BLADE WARNING: USE ONL Y CROSS-CUTTING SAW BLADES. WHEN USING CARBIDE TIPPED BLADES, DO NOT USE BLADES WITH DEEP GULLETS AS THEY CAN DEFLECT AND CONT ACT THE GUARD. USE ONL Y 10 ″ ″ DIAMETER SAW BLADES WHICH ARE RA TED FOR 6000 RPM OR HIGHER AND HA VE 5/8 ″ ″ DIAMETER ARBOR HOLES.
18 Fig. 47 Fig. 48 Fig. 49 BRUSH INSPECTION AND REPLACEMENT CAUTION: BEFORE INSPECTING THE BRUSHES, DISCONNECT THE MACHINE FROM THE POWER SOURCE. Brush life varies. It depends on the load on the motor . Check the brushes after the first 50 hours of use for a new machine or after a new set of brushes has been installed.
19 NOTES.
20 Delta will repair or r eplace, at its expense and at its option, any Delta machine, machine part, or machine accessory which in normal use has proven to be defective in workmanship or material, pr .
The following are trademarks of POR TER-CABLE • DEL T A Corporation (Las siguientes son marcas r egistradas de PORTER-CABLE S.A.): BAMMER ® , INNOV A TION THA T WORKS ® , JETSTREAM ® , LASERLOC .
デバイスEpson 36-075の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Epson 36-075をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはEpson 36-075の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Epson 36-075の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Epson 36-075で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Epson 36-075を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はEpson 36-075の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Epson 36-075に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちEpson 36-075デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
