Epsonメーカー4001968の使用説明書/サービス説明書
ページ先へ移動 of 97
“) EPSON TERM NAL PRINTER Myk. 800 SERVICE MANUAL EPSON ) 4001968 Rev. A.
NOTICE Al l right s reserved . Reprodu c tio n o f an y par t o f thi s manua l i n an y for m whatsoev e r witho u t SEIKO EPSON’ s expr e s s writte n permission i s forbidden. The content s of this manua l are subject s to cha n ge without notice.
PRECAUTIONS Precautionary notations throughout the text are categorized relative to 1) personal injury and 2) damage to equipment. DANGER Signals a precaution which, if ignored, could result in serious or fatal personal injury. Great caution should be exercised in performing procedures preceded by DANGER Headings.
PREFACE This manual describes functions, theory of electrical and mechanical operations, maintenance, and repair of stylus 800. The instructions and procedures included herein are intended for the experience repair technician, and attention should be given to the precautions on the preceding page.
Revision Issue Date Revision Page Rev. A December 18, 1992 First issue Added information: Rev. B May 7, 1993 Chapter 2 (Page 2-23) Chapter 3 (Page 3-5/6) Chapter 6 (Page 6-1/2) Rev. C June 11, 1993 Corrected the figure: Chapter 2 (Page 2-8) Added information: Rev.
TABLE OF CONTENTS CHAPTER 1. GENERAL DESCRIPTION CHAPTER 2. OPERATING PRINCIPLES CHAPTER 3. DISASSEMBLY AND ASSEMBLY CHAPTER 4. ADJUSTMENTS CHAPTER 5. TROUBLESHOOTING CHAPTER 6.
Chapter 1 General Description Table of Contents 1.1 FEATURES 1-1 1.2 SPECIFICATIONS 1-2 1.2.1 1.2.2 1.2.3 1.2.4 1.2.5 1.2.6 1.2.7 1.2.8 1.2.9 Printing Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-2 Paper Handling Specification .
List of Tables Table 1-1. Print Speed and Printable Columns . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 Table 1-2. Character Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3 Table l-3. Adjust Lever Settings .
STYLUS 800 Service Manual General Description 1.1 FEATURES The Stylus 800 is a serial inkjet printer that uses a newly developed inkjet technology to accomplish a superb quality output with high-speed printing. The major features of this printer are: Ll High print quality from a new inkjet technology.
General Description STYLUS 800 Service Manual 1.2 SPECIFICATIONS This section provides detailed statistics for this printer. 1.2.1 Printing Specification Print system: On-demand ink jet system Nozzle configuration: 48 nozzles (12 nozzles x 4 staggered columns) I I .
STYLUS 800 Service Manual Geneml Descri@ion Character sets: Legal and 14 international character sets. Character tables: See Table 1-2. Table 1-2. Character Tables Character Table US Version European Version Pacific Version ITALIC o 0 0 PC437 (U.
General Description STYLUS 800 Sewice Manual 1.2.2 Paper Handling Specification Feeding system: Friction feed from built-in sheet feeder or manual insertion slot. Notes: The following operation are not al/owed. 1. Reverse feeding within 3 mm (O. 12 inches) from the top edge of the paper or 16 mm (0.
STYLUS 800 Service Manual Geneml Description Printable area: Cut Sheet (with built-in sheet feeder) B (Left marain)> — r c 4 (Right marain]~ Printable area . r ! A (Top margin) ID I (Bottom margin) 1 Figure 1-3. Printable Area - Cut S~eet (Built-in Sheet Feeder) Cut Sheet / Envelope (with the manual insertion slot) B c (Left marain) ~.
General Description SNLUS 800 Service Manual Adjust lever settings: The adjust lever, attached to the carnage unit, must be set to proper position for the paper thickness, as shown in Table 1-3. Table 1-3. Adjust Lever Settings Lever Position Paper Type Paper Thickness LEFT Cut Sheets ~;%26--00~iO!$ RIGHT Envelopes 0.
STYLUS 800 Service Manual Genera/ Descriptim 1.2.5 Environmental Conditions Table 1-4. Environmental Conditions Description Operating Storage Temperature 10-35 ‘c (50 - 95 ‘I=)(*1) -20- 60 “C (-4 - 140 ‘F) (*2) Humidity 20- 80% RH (*1,*3) 5- 85~0 RH (*2,*3) Resistance to shock 1 G, within 1 msec.
General Description STYLUS 800 Service Manual 1.2.7 Reliability MTBF: 4000 power on hours (POH) at a duty cycle of 10% MCBF: 3 million lines (excluding the printhead) Printhead life: 1 billion dots per nozzle Total print volume: 75000 pages (with A4 or Letter size paper) 1.
SNLUS 800 Service Manual GenemlDescription 1.3 INTERFACE SPECIFICATION The Stylus 800 is equipped with an 8 bit parallel interface, standard. Data format: 8 bit parallel Synchronization: STROBE pulse .
General Description SNLUS 800 Service Manual Table 1-6. Signal and Connector Pin Assignments (Continued) Pin No. Signal Name I/o Description 16 GND Signal ground. 17 CHASSIS-GND - Chassis ground. (Both chassis ground and signal ground are connected in the ptinter.
STYLUS 800 Service Manual General DescriWion 1.4 PRINTER OPERATIONS This section describes the basic operations of the printer. 1.4.1 Control Panel The control panel of this printer contains five non-lock type push buttons and nine LED indicators for easy operation of the various printer functions.
General Description STYLUS 800 Service Manual 1.4.2 Panel Operation at Power On The following functions can be activated at power on by holding down the specified button on the control panel. Self-test mode: Start the self-test printing mode by turning the printer on while holding down the FONT button.
SWLUS 800 Service Manual General Description 1.4.4 Initial ink Charge When the printer is to be set up for primary use, whole ink supply path of the printer must be filled with a new ink, by performing the initial ink charge operation. [Step 1] [Step 2] [Step 3] [Step 4] Turn the printer on and press the PAUSE button to pause the printer.
General Description STYLUS 800 Service Manual 1.5 MAIN COMPONENTS The main components of this printer are: O Printer mechanism (M-481O) Q Main control board (C106 MAIN BOARD) ~ Power supply unit (C106PSB/PSEBOARD) Cl Control panel Cl Housing 1.5.1 Main Control Board (C106 MAIN BOARD) The C106 MAIN BOARD is the main conboller of the Stylus 800.
STYLUS 800 Service Manual General Description 1.5.2 Power Supply Unit (C106 PSBIPSE BOARD) The power supply unit converts input AC voltage and generates different DC voltages required by the printer mechanism and other electrical circuities. The C106 PSB BOARD is for 120VAC input, and the C106 PSE BOARD is for 220 to 240VAC input.
,. . . . . f.:,’ ..
Chapter 2 Operating Principles Table of Contents 2.1 OVERVIEW 2-1 2.2 OPERATING PRINCIPLES OF THE PRINTER MECHANISM 2-1 2.2.1 Printer Mechanism . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. .2-2 2.2.2 Carriage Drive Mechanism .
List of Figures Figure 2-1. Figure 2-2. Figure 2-3. Figure 2-4. Figure 2-5. Figure 2-6. Figure 2-7. Figure 2-8. Figure 2-9. Figure 2-10 Figure 2-11 ~D•Œ Figure 2-12 Figure 2-13 Figure 2-14 Figure 2-15 Figure 2-16. Figure 2-17. Figure 2-18. Figure 2-19.
STYLUS 800 Service Manual Operating Principles 2.1 OVERVIEW This section describes the operating principles of the printer mechanism and the electrical circuits of the Stylus 800.
Operating Principles STYLUS 800 Service Manual 2.2.1 Printer Mechanism The printer mechanism of this printer uses a drop-on-demand ink jet system similar to the system used on all other Epson ink jet printers. However, the printhead in this system is completely redesigned to make it compact and highly reliable.
STYLUS 800 Service Manual Operating Principles Principles of the Printing Operation The operation of the printhead to inject ink from each nozzle is: (1) Normal state No electrical charge is applied to the MLP (Multi-Layer Piezoelectric) element attached to the back of the cavity, and pressure inside the cavity is kept at constant level.
Operating Principles STYLUS 800 Service Manual 2.2.2 Carriage Drive Mechanism The timing belt attached to the base of the carriage unit is driven by the carriage motor, causing the carriage unit to move along the carriage guide shaft left to right, or vice versa.
) STYLUS 800 Service Manual Operating Principles 2.2.3 Paper Feed Mechanism This printer’s paper feed mechanism can feed paper either from the built-in ASF (auto sheet feeder) or the manual feed slot.
Operating Principles STYLUS 800 Sewice Manua) 2.2.4 Ink System This printer’s ink system is composed of the following mechanisms: ■ Ink cartridge ■ Pump mechanism E Cap mechanism H Printhead cleaning mechanism ■ Waste ink drain tank The figure below shows a diagram of the ink system.
STYLUS 800 Service Manual Operating Principles 2.2.5 Pump Mechanism The paper feed motor drives the pump mechanism when the transmission gear is moved to the position where the paper feed motor engages the pump mechanism gear trains, when the carriage unit is at the ink system home position.
Operating Principles STYLUS 800 Service Manual Table 2-4. Pump Mechanism Operation PF Motor Rotational Direction Operation 1 Pumping CW (forward rotation) Pseudo-pumping (False absorbing) Gear backrus.
STYLUS 800 Service Manual Operating Principles 2.2.6 Cap Mechanism The cap mechanism prevents the printhead nozzles from drying or bubbles from forming inside the nozzle while the printer is not in use.
Operating Principles STYLUS 800 Service Manual 2.3 OPERATING PRINCIPLES OF THE ELECTRICAL CIRCUITRIES The Stylus 800 contains the following circuit board units: ■ C106 MAIN BOARD (Main control circu.
STYLUS 800 Service Manual Operating Principles The figure below shows a block diagram of the power supply circuit (C106 PSB/PSE). This power supply circuit employs the RCC (ringing choke converter) switching control system.
Operating Principles STYLUS 800 Service Manual 2.3.2 Operating Principles of the Main Control Circuit The main control circuit of this printer is the C106 MAIN BOARD. This circuit is controlled by the 8-bit CPU TMP96C141F (ICI), running at 19.6608 MHz.
STYLUS 800 Service Manual Operating Principles 2.3.2.1 Reset Circuits The C106 MAIN BOARD contains two reset circuits: the +5 V monitor reset circuit and the +35 V monitor reset circuit.
Operating Principles STYLUS 800 Service Manual 2.3.2.3 Ink End Detection The IE (Ink End) sensor attached to the carriage detects, not only the ink end, but also when ink is low and whether an ink cartridge is installed. The detected status is classified to five modes according to the output voltage level of the IE sensor.
STYLUS 800 Service Manual Operating Principles 2.3.2.4 Carriage Motor Drive Circuit Carriage motor drive IC SLA7024 (IC13) drives the carriage motor for the printer mechanism by a I constant current, unipolar drive system.
Operating Principles STYLUS 800 Service Manual 2.3.2.5 Paper Feed Motor Drive Circuit The paper feed motor for this printer drives the following mechanisms: c ~.,, ; ‘ 9 Paper feed mechanism . . ■ Paper pickup mechanism ■ Pump mechanism Driver IC SMA6501 (QM1) drives the paper feed motor by a constant voltage, unipolar drive system.
STYLUS 800 Service Manual Operating Principles 2.3.2.6 Printhead Drive Circuit The printhead drive circuit for this printer is composed of the following two parts: ❑ Common drive circuit (trapezoida.
Operating Principles SNLUS 800 Service Manual 2.4 INK SYSTEM MANAGEMENT This section explains how the ink system is controlled to protect the printhead and the ink supply system and to ensure highquality output.
STYLUS 800 Service Manual Opmeting Principles 2.4.1 Ink Operations There are various ink operations that can be performed selectively by the printer. 2.4.1.1 Power on Operation Power on consists of the following operations, and only one of these operations is performed, depending on the position of the carnage when the printer is turned on.
Operating Principles STYLUS 800 Service Manual 2.4.1.3 Standby Operation The standby operation prevents an increase in the viscosity of the ink held inside the printhead nozzles. This operation is performed automatically if no data is received for more than three seconds from the last print data.
STYLUS 800 Service Manual Operating Principles 2.4.1.6 Cleaner Blade Operation The cleaner blade operation eliminates any dust or ink attached to the nozzle plate surface.
Operating Principles STYLUS 800 Service Manual 2.4.1.8 Disengage ON Operation This operation sets the switch lever to the position where it transmits the PF motor drive to the pump mechanism. 1) Moves the carriage to the position D where the lever is set to the specified position.
STYLUS 800 Semice Manual Operating Principles 2.4.2.4 Protect Counter There are four protect counters to manage the amount of ink draining to the waste ink drain tank. The value of these counters is stored in EEPROM on the main board upon power off. t ■ Prot@ counter A This counter is used to manage the total amount of drained ink.
Chapter 3 Disassembly and Assembly Table of Contents 3.1 OVERVIEW 3-1 3.1.1 Precautions for Disassembling the Printer . . . . . . . . . . . . . . . . . . . . .. ...3-1 3.2 DISASSEMBLY AND ASSEMBLY 3-2 3.2.1 CASE, UPPER Removal . . . . . . . . . . . . .
STYLUS 800 Service Manual Disassembly and Assembly 3.1 OVERVIEW This section describes procedures for disassembling the main components of this printer. Unless otherwise specified, the disassembled unit or components can be reassembled simply by reversing the disassembly procedure.
Disassembly and Assembly STYLUS 800 Service Manual 3.2 DISASSEMBLY AND ASSEMBLY Follow the instruction in Section 3.1.1 to disassemble the prt”nter. I This section consists of the subheads shown in the diagram below. Refer to the exploded view of the printer in the Appendix, if necessary.
STYLUS 800 Service Manual Disassembly and Assembfy 3.2.1 CASE, UPPER Removal [Step 1] [Step 2] [Step 3] [Step 4] [Step 5] [Step 6] Remove the COVER, PRINTER by releasing the tabs holding it to the CASE, UPPER. Remove the SUPPORT, PAPER by releasing the tabs holding it to the CASE, LOWER.
Disassembly and Assembly STYLUS 800 Service Manual 3.2.2 Power Supply Unit (C106 PSB/PSE BOARD) Removal [Step 1] [Step 2] [Step 3] [Step 4] Remove the CASE, UPPER. (Refer to Section 3.2.1.) .( ,:,, Disconnect the cables from comectors CN1 and CN2 of the C106 PSB/PSE BOARD.
I I STYLUS 800 Service Manual Disassembly and Assembly 3.2.3 Main Controller (CI06 MAIN BOARD) Removal [Step 1] Remove the CASE, UPPER. (Refer to Section 3.2.1.) [Step 2] Disconnect the cables from the connectors CN2/CN3/CN4/CN5 /CN6/CN7 of the C106 MAIN BOARD.
Disassembly and Assembly STYLUS 800 Service Manual 3.2.4 PRINTER MECHANISM (M-481O) Removal [Step 1] Remove the CASE, UPPER. (Refer to Section 3.2.1.) [Step 2] Remove the power supply unit. (Refer to Section 3.2.2.) [Step 3] Remove the main controller.
SNLUS 800 Servke Manual Disassembly and Assembly 3.2.5 PRINTER MECHANISM Disassembly The procedures described in this section explain removal of components within the printer mechanism. 3.2.5.1 PRINTHEAD UNIT Removal [Step 1] Remove the printer mechanism.
Disassembly and Assembly STYLUS 800 Service Manual Ink Cartridge @ o 0“ I Q / Printhead Unit a -. =’5” ~ 22% %.. Figure 3-7. PRINTHEAD UNIT Removal (Continued) .
SNLUS 800 Sewice Manual Disassembly and Assembly 3.2.5.2 PUMP UNIT Removal [Step 1] [Step 2] [Step 3] [Step 4] [Step 5] [Step 6] Remove the PRINTER MECHANISM. (Refer to section 3.2.4.) Move the carriage to the middle of the printer. The carriage is located between first and second paper guide roller, as illustrated in figure below.
Disassembly and Assembly STYLUS 800 Sewice Manual Pump Unit f ,*- 4 . Figure 3-9. PUMP Unit Removal (Continued) 3-1o Rev. A.
STYLUS 800 Service Manual Disassembly and Assemb/y 3.2.5.3 CLEANER, HEAD Replacement [Step 1] Remove the PUMP UNIT. (Refer tosection3.2.5.2.) [Step 2] Remove the CLEANER, HEAD from the pump unit.
Dkassembly and Assembly STYLUS 800 Servke Manual 3.2.5.4 CARRIAGE UNIT Removal [Step 1] [Step 2] [Step 3] [Step 4] [Step 5] [Step 6] Remove the printer mechanism. (Refer to section 3.2.4.) @ Remove the tension spring that holds the CR motor in place. Then, take the timing belt out of the CR motor drive pulley and the driven pulley.
STYLUS 800 Sewice Manual Disassembly and Assembiy 3.2.5.5 CR MOTOR Removal [Step 1] Remove the printer mechanism. (Refer to section 3.2.4.) [Step 2] Remove the tension spring and take thetimingbeltout of the CRmotordrive pulley.
Disassembly and Assembly STYLUS 800 Service Manual 3.2.5.6 PF MOTOR Removal [Step 1] Remove theprinter mechanism. (Refer tosection3.2.4.) [Step 2] Remove3 screws (CBB screw (M3x 10) x3), and remove theholdingplate. Since the holding plate retains the pressure springs under it, be sure not to loose them when removing the holding plate.
STYLUS 800 Service Manual Disassembly and Assembly 3.2.5.7 [Step 1] [Step 2] [Step 3] [Step 4] PAPER FEED ROLLER ASSEMBLY Removal Remove the printer mechanism. (Refer to section 3.2.4.) Remove the carriage unit. (Refer to section 3.2.5.4.) Remove 2 screws (CBB screw (M3 x 10) x 2), and remove the frame assembly.
Chapter 4 Adjustments Table of Contents 4.1 OVERVIEW 4-1 4.1.1 Precautions for Adjustment . . . . . . . . . . . . . . . . . . . . . . . 4.2 BI-DIRECTIONAL PRINTING ALIGNMENT ADJUSTMENT . . . . . . . . . . . . . 4-1 4-1 4.3 DEFAULT SEITING PARAMETER REGISTRATION 4-2 4.
STYLUS 800 Service Manual Adjustment 4.1 OVERVIEW This section describes procedures of the adjustment required when the printer is disassembled and assembled after repair. 4.1.1 Precautions for Adjustment You should refer to the precautions below when adjusting the printer.
Adjustment STYLUS 800 Sewice Manual 4.3 DEFAULT SETTING PARAMETER REGISTRATION The set up value that specifies the destination of the product distribution, is stored in the EEPROM on the main board (C106 MAIN). Therefore, this set up value must be written in EEPROM when the main board or the EEPROM chip is replaced.
STYLUS 800 Service Manual Adjustment Shaft holder Carriage guide shaft T I Ii I . . . . . . . . ~ 6’ ““-7L I Ii :: 1: .. ;....: I A 4 LEH PG Gauge RIGHT Adjust position Adjust position Shaft holder 7 arriaga . . . . . . . . . . . . . . . . . .
Chapter 5 Troubleshooting 1 Table of Contents 5.1 OVERVIEW 5-1 5.2 UNIT LEVEL TROUBLESHOOTING 5-3 5.2.1 Printer does not operate at power on . . . . . . . . . . . . . . . . . . . . . . .......5-4 5.2.2 Error is detected . . . . . . . . . . . . . . . .
STYLUS 800 Service Manual Troubleshooting 5.1 OVERVIEW The printer may exhibit different symptoms for the same problem, which makes troubleshooting more difficult. This section, however, provides simple and effective ways to facilitate troubleshooting.
Troubleshooting STYLUS 800 Service Manual Table 5-3. Error Codes Error PAPER INK END PAUSE LED LED LED Buzzer Recovery Load the paper and press the Paper out ON OFF OFF V* ~ ~ tim~ buttons as follows: 1. PAUSE 2. LOAD/EJECT Paper jam BLINKS OFF OFF V* x 3 times Same as above.
STYLUS 800 Service Manual Troubleshooting 5.2 UNIT LEVEL TROUBLESHOOTING When a problem occurs, you can distinguish the defective unit by referring the symptoms of the defect. The table below lists the svrrmtom of certain defects, and you can easily identify what the problem.
Troubleshooting STYLUS 800 Service Manual 5.2.1 Printer does not operate at power on F Use the comxt YES Replace the fuse and discmwt cN70n the C106 MAIN board.. NO NO Check the output voltage of Ihe C1C6 YES PWPSEal CN2. w Replace the YES printer mechanism.
STYLUS 800 Sewke Manual TmuMeshootjng 5.2.2 Error is detected z START Identify the type of enor indicated. (SaeTable 5-3.) Turn the printer NO NO NO Waste ink drain tank over-fbw r Replace the waste ink absorbing material, and raset the protect counter.
Troubleshooting STYLUS 800 Service Manual 5.2.3 Failure occurs during printing F NO NO YEs J NO ES Adjust the Bkdirectionel NO Reptecethe printer mechanism. ES Es NO I R@cetheC106 MAIN bcaNI. I NO F Es #-: ““f “ . . {,:.;’” * END + END . 5-s Rev.
STYLUS 800 Service Manual Troubleshooting 5.2.4 Printer does not feed the paper correctly NO Set the paper YES Ccmcfly. I NO G Replace the C1G6 MAIN board. Verify that nothing abnormal within the paper path. Also confirm that there is nci any foreign objects that may interfare the paper movement, Replace the YES printer mechanism.
Troubleshooting STYLUS 800 Servjce Manual 5.2.5 Control panel operation is abnormal m YES & Is the prcblem YES corrected ? NO d Replace the ccntrol panel.
STYLUS 800 Sewice Manual Troubleshooting 5.3 UNIT REPAIR - CI06 PSB/PSE BOARD This section describes the problems related to the power supply board (C106 PSB/PSE).
Troubleshooting STYLUS 800 Service Manual 5.4 UNIT REPAIR - CI06 MAIN BOARD This section describes the problems related to the main controller board (C106 MAIN).
STYLUS 800 Service Manual Troubleshooting Table 5-6. Repair of the C106 MAIN (Continued) Rev. A 5-11.
Troubleshooting SNLUS 800 Service Manual 5.5 UNIT REPAIR - PRINTER MECHANISM (M-4810) Troubles related to the printer mechanism should be repaired according to the troubleshooting procedures in Table 5-7.
SNLUS 800 Service Manual Troubleshooting Table 5-7. Repair of Printer Mechanism (Continued) Symptom Condition Cause Checkpoint Solution The head cable is Check the head cable for Replace the disconnected. disconnection. cable., The carriage Printing is not moves, but no The printhead is Replace the printhead to Replace the performed.
Chapter 6 Maintenance Table of Contents 6.1 PREVENTIVE MAINTENANCE 6-1 6.2 SERVICE MAINTENANCE 6-1 6.2.1 Printhead Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. .6-1 6.2.2 Waste Ink Drain Tank Replacement.
SNLUS 800 Service Manual Maintenance 6.1 PREVENTIVE MAINTENANCE Altough this printer is designed that no specific maintenance is required in regular basis, it is good idea to clean the printer throughly whenever you get a chance to do so.
Maintenance STYLUS 800 Service Manual 6.3 LUBRICATION The printer must be lubricated properly when the printer is disassembled for component replacement, or if the mechanical noise exceeds a certain level.
SNLUS 800 Service Manual Maintenance Figure 6-1. Lubrication Points Rev. A 6-3 I.
Appendix Table of Contents A.1 CONNECTOR SUMMARY A-1 A.2 CIRCUIT DIAGRAMS A-5 A.3 CIRCUIT BOARD COMPONENT LAYOUT A-9 A.4 EXPLODED DIAGRAM A-12 List of Figures Figure A-1. Interconnection of Major Components . . . . . . . . . . . . . . . . . . . . . . A-1 Figure A-2.
SNLUS 800 Sewice Manual Appendix A.1 CONNECTOR SUMMARY Figure below shows the intercomection between the major components of the Stylus 800. +11 c-) AC Input _ z CI06 PSB/PSE Parallel IIF ICN2 I Iw-1 OJ z I I CN8 ] I CN6 ] ICN5 ~ . . . . . . . . . . .
Appendix SNLUS 800 Service Manual Table A-1. Connector Summary Board Location Pin Description Cl 06 MAIN CN1 36 pins Centronics parallel l/F CN2 12 HEAD-1 (to printhead unit) CN3 12 HEAD-2 (to printhe.
STYLUS 800 Service Manual Amandix Pin 1 2 3 4 5 6 7 8 9 10 11 12 Table A-4. Connector Pin Assignment - CN3 1/0 o 0 0 0 0 I I Name GND HCLK GND LAT GND SI GND VE HPV HP +5V TH Description Ground Synchr.
Appendix STYLUS 800 Service Manual Table A-9. Connector Pin Assignment - CN8 Pin 1/0 Name Description 1 +!FN +5V DC 2 0 LEDO LEDO driie signal (“L”=LED on) 3 I Swl SW1 input signal (“L”=Button.
(’;’:, . . (J . STYLUS 81M Service Manual Append& : ‘ + Y o .x c .- m In z : Rev.D A-7’ I.
Appendix STYLUS 800 Service Manual m -J =~ . I I I u + w . z 0 r ‘al 0 II-l I t I I * h & w .s N 0 3 m A-a’ Rev.D.
STYLUS S00 Sarvice Manual Appandix o s----l r-l n - ‘ 77 t . . ● “+3 ● ll I . [ u -J , - j~s L w BJ?lu-q- ● %7(EM U 2010435 0! Al ‘-’k-’, 73 —-” 8 Id Orl u ‘IC10 a ~wF & L I ‘Y ) 0 0 0 0 Ki!!l ID D m m m o 0 0 HI C. <. ,.
Appendix STYLUS 800 Service Manual ~.. *,, n— —u.. , PO. CO”7, ””C0 P*OICC1 10” ACAI”8? R18X CAUT 10N . ...,.rr...oru.u. – . 0~ Vtn=. REPLACE ONLY .11. 8.. C1YPC l.--J ASSY . C 106 d’+=- ‘ 2013030 0 0 PSB-B~ t 1 T CMK-P2X ~ A ‘~ ( .
. . STYLUS 800 Service Manual Appendix @ LED8 (ORG) @ LEDO (RED ) Swln @ LED1 (RED) J8 A @ LED2 (GRN) @=LE#3@( GRN ) SW2 • 000 Whlw J 3 Xt o 0 ,CN 1 18 u Figure A-4.
デバイスEpson 4001968の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Epson 4001968をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはEpson 4001968の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Epson 4001968の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Epson 4001968で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Epson 4001968を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はEpson 4001968の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Epson 4001968に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちEpson 4001968デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。