EpsonメーカーEZ-Loadの使用説明書/サービス説明書
ページ先へ移動 of 21
EZ-Load Thermal Printer Owner's Manual First Edition: August 2002 Last Revision: Sept 21, 2005 Document # 101049.
EZ-Load Thermal Printer Owner’s Manual Legal Notices Disclaimer Information in this docum ent is subject to change wit hout notice. Consult your Nan optix Inc.
EZ-Load Thermal Printer Owner’s Manual Nanoptix Inc. is not responsibl e for any radio or television interference caused by unauthorized modification of this equipmen t or the subs titution or attach ment of connec ting cables and equipment other than tho se specified by Nanoptix Inc.
EZ-Load Thermal Printer Owner’s Manual Table of Contents 1. About the Printer ........................................................................ 1 1.1 Description of Printer .....................................................................
EZ-Load Thermal Printer Owner’s Manual Figures FIGURE 1: NANOPTIX EZ-LOAD PRINTER ................................................................................................. 1 FIGURE 2: RESETTING PRINTER .......................................
EZ-Load Thermal Printer Owner’s Manual Tables TABLE 1: SPECIFICATION ........................................................................................................................... 2 TABLE 2: TROUBLESHOOTING WITH THE STA TUS LED ........
EZ-Load Thermal Printer Owner’s Manual 1. About the Printer 1.1 Description of Printer The Nanoptix EZ-Load printer is extremely fast, quiet, and very reliable. With thermal printing technology, there is no ribbon cassette to change, and paper loading is extremely simple.
EZ-Load Thermal Printer Owner’s Manual 1.2 General specifications Print Method Direct Thermal Resolution 8 dot/mm (203 dpi) Print Width 80mm Paper Width 80mm or 82.
EZ-Load Thermal Printer Owner’s Manual 1.3 Printer Controls To reset Printer Simply plug and unplug the printer to reset in t he event of a fault condition. Once the printer is re-plugged, it will go through a startup routine and reset itself. Figure 2: Resetting Printer 101049 Sept.
EZ-Load Thermal Printer Owner’s Manual Paper Feed Button Use the Paper Feed Button to advance the paper. Paper Feed Figure 3: Paper Feed Button 101049 Sept.
EZ-Load Thermal Printer Owner’s Manual 1.4 Changing Paper Caution: Do not operate the printer if it runs out of paper. The printer will not operate without paper, but it may continue to accept data from the host computer. Because the printer cannot print any transactions, the data may be lost.
EZ-Load Thermal Printer Owner’s Manual 4. Pull up on the top of the paper roll and align the left edge of the paper with the line on the front label. Figur e 5: Aligning Paper Edge 5. Close the door onto the paper. Figure 6: Closing Door 101049 Sept.
EZ-Load Thermal Printer Owner’s Manual 6. Advance the paper by pressing on the paper feed button and tear off the excess paper. Note: In the event of a paper jam, remove the roll, tear a new clean edge, and replace it in the paper bucket, as described above.
EZ-Load Thermal Printer Owner’s Manual 1.5 Testing the Printer Run this test to check the printer. Th e test prints and cuts a resident test ticket. Verify this ticket to judge the printing quality.
EZ-Load Thermal Printer Owner’s Manual 1.6 Troubleshooting the Printer The printer is simple and generally trouble-free, but from time to time minor problems may occur. Follow these procedures to determine the cause and resolution of any problems the printer may be having.
EZ-Load Thermal Printer Owner’s Manual Printer Does Not Work Problem Possible Causes What to Do Check that printer cables are properly connected on both ends. Printer not plugged in. Check that the host or power supply is switched on. Check Printer LED.
EZ-Load Thermal Printer Owner’s Manual 2. Media and Supplies Guide 2.1 Thermal Paper Specifications The printer requires qualified thermal paper with the following dimensions: Width Diameter Outside Core Diameter 80 mm ± .2 mm (3.15 in. ± .008 in.
EZ-Load Thermal Printer Owner’s Manual 2.3 Ordering Miscellaneous Supplies Power Supply and Power Cord Contact your sales representative to order the power supply and power cords listed in the table. The numbers are for reference only. Suppliers may use other numbers.
EZ-Load Thermal Printer Owner’s Manual Communication Cables Pin-Out The tables below detail the connection pin-out for the RS-232 interface (Female Receptacle DB-9).
EZ-Load Thermal Printer Owner’s Manual 3. Communicating with the Printer Over the years, Nanoptix has developed emulations for compatibility with the most popular printers in the market. At the time of printing this manual, the fo llowing emulations are available: i.
EZ-Load Thermal Printer Owner’s Manual APPENDIX A: Mechanical Drawings Figure 8: Mechanical Dimensions (in mm) 101049 Sept. 21, 2005 15.
デバイスEpson EZ-Loadの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Epson EZ-Loadをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはEpson EZ-Loadの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Epson EZ-Loadの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Epson EZ-Loadで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Epson EZ-Loadを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はEpson EZ-Loadの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Epson EZ-Loadに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちEpson EZ-Loadデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
