EpsonメーカーPowerLite Home Cinema 2030の使用説明書/サービス説明書
ページ先へ移動 of 179
PowerLite ® Home Cinema 2000/2030 User's Guide.
.
Contents PowerLite Home Cinema 2000/2030 User's Guide .................................................................................... 9 Introduction to Your Projector ..........................................................................
Connecting to External Speakers .................................................................................................. 32 Connecting to External USB Devices ..................................................................................
Changing the Projection Mode Using the Menus ........................................................................... 61 Image Aspect Ratio ............................................................................................................
Cleaning the 3D Glasses ............................................................................................................... 93 Cleaning the Projector Case ....................................................................................
Remote Control Specifications ......................................................................................................... 121 Projector Dimension Specifications ............................................................................
.
PowerLite Home Cinema 2000/2030 User's Guide Welcome to the PowerLite Home Cinema 2000/2030 User's Guide . 9.
Introduction to Your Projector Refer to these sections to learn more about your projector and this manual. Projector Features Notations Used in the Documentation Where to Go for Additional Information.
Easy-to-use setup and operation features • Real-time, automatic vertical keystone correction and horizontal keystone correction slider for flexible projector placement • Epson's Instant Off and Direct Power On features for quick setup and shut down • 1.
5 Projector documentation CD Parent topic: Projector Features Additional Components Depending on how you plan to use the projector, you may need to obtain the following additional components: • To receive a component video signal, you need a D-sub, 15-pin, component-to-VGA video cable.
Optional Equipment and Replacement Parts You can purchase screens, other optional accessories, and replacement parts from an Epson authorized reseller. To find the nearest reseller, call 800-GO-EPSON (800-463-7766). Or you can purchase online at epsonstore.
In addition, Epson offers free Extra Care Home Service. In the unlikely event of an equipment failure, you won’t have to wait for your unit to be repaired. Instead, Epson will ship you a replacement unit anywhere in the United States, Canada, or Puerto Rico.
Projector Parts - Base Projector Parts - Control Panel Projector Parts - Remote Control Parent topic: Introduction to Your Projector Projector Parts - Front/Top 1 Control panel 2 Horizontal keystone s.
12 A/V Mute slide (lens cover) 13 Exhaust vent 14 A/V Mute slide lever 15 Lamp cover Parent topic: Projector Part Locations Related references Projector Light Status Related tasks Installing a Securit.
5 Audio Out port 6 Service port 7 USB Type A port 8 Audio ports 9 RS-232C port 10 Remote receiver 11 AC input port Parent topic: Projector Part Locations Projector Parts - Base 1 Front adjustable foot.
4 Mounting bracket holes Parent topic: Projector Part Locations Projector Parts - Control Panel 1 Power button/light 2 Source button (cycles through the list of sources) 3 Menu button (accesses projec.
Projector Parts - Remote Control 1 Power button 2 Source buttons 3 HDMI Link button (displays the settings menu for HDMI Link), Link Menu button (displays the main menu of the connected device); and c.
4 Menu button (accesses projector menu system) 5 Arrow buttons (move through on-screen options) 6 User button (customizable for different functions) 7 Color Mode button (selects display modes) 8 2D/3D.
Setting Up the Projector Follow the instructions in these sections to set up your projector for use. Projector Placement Projector Connections Installing Batteries in the Remote Control Opening the Lens Cover Projector Placement You can place the projector on almost any flat surface to project an image.
Rear Front Ceiling Rear Ceiling 22.
Wherever you set up the projector, make sure to position it squarely in front of the center of the screen, not at an angle, if possible. If you project from the ceiling or from the rear, be sure to select the correct Projection option in the projector's menu system.
16:9 Aspect Ratio Image or Screen Screen or image size Projection distance Wide to Tele 1 50 inches (126 cm) 53 to 64 inches (135 to 162 cm) 2 80 inches (203 cm) 85 to 103 inches (217 to 261 cm) 3 100.
Screen or image size Projection distance Wide to Tele 1 50 inches (126 cm) 57 to 69 inches (146 to 176 cm) 2 80 inches (203 cm) 93 to 111 inches (235 to 283 cm) 3 100 inches (254 cm) 116 to 139 inches.
Connecting to External Speakers Connecting to External USB Devices Parent topic: Setting Up the Projector Related references Projector Setup Settings - Extended Menu Connecting to Video Sources Follow the instructions in these sections to connect video devices to the projector.
commands, set your game console's output format to a progressive signal of 480p or 720p. See your game console documentation for instructions. You can also select the Fast setting using the Fast/Fine button on the remote control to reduce lag time.
Parent topic: Connecting to Video Sources Related tasks Connecting to External Speakers Connecting to a Component-to-VGA Video Source If your video source has component video ports, you can connect it to the projector using an optional component-to-VGA video cable.
Related tasks Connecting to a Video Source for Sound Connecting to a Composite Video Source If your video source has a composite video port, you can connect it to the projector using an optional RCA-style video or A/V cable. 1. Connect the cable with the yellow connector to your video source's yellow video output port.
2. Connect the other end of the cable to the projector's Audio port or ports. Note: To add additional sound, connect your video source and speakers to an audio video receiver, then connect the receiver to the projector using one of the receiver's compatible video outputs (an HDMI connection provides the best image quality, if available).
3. Connect the other end to a PC port on the projector. 4. Tighten the screws on the VGA connector. Parent topic: Connecting to Computer Sources Related tasks Connecting to a Computer for Sound Connecting to a Computer for HDMI Video and Audio If your computer has an HDMI port, you can connect it to the projector using an optional HDMI cable.
Parent topic: Connecting to Computer Sources Related tasks Connecting to External Speakers Connecting to a Computer for Sound If your computer presentation includes sound and you did not connect it using the projector's HDMI port, you can still play sound through the projector's speaker system.
4. Connect the stereo mini-jack end of the cable to your projector's Audio Out port. Parent topic: Projector Connections Connecting to External USB Devices Follow the instructions in these sections to connect external USB devices to the projector.
• Formatted in FAT or FAT32 • Self-powered by their own AC power supplies (bus-powered hard drives are not recommended) • Avoid using hard drives with multiple partitions You can project slide shows from image files on a connected USB device or memory card reader.
2. Press the Slideshow button on the remote control. 3. Press the button again to cycle through other USB sources, if available. Parent topic: Connecting to External USB Devices Disconnecting a USB De.
2. Insert the batteries with the + and – ends facing as shown. 3. Close the battery cover and press it down until it clicks into place. Warning: Dispose of used batteries according to local regulations.
Opening the Lens Cover 1. To open the projector's lens cover, slide the A/V Mute slide lever until it clicks into the open position. 2. To cover the lens or temporarily turn off the projected picture and sound, slide the A/V Mute slide cover closed.
Wireless Network Projection You can send images to your projector through a wireless network. To do this, you must install the Epson 802.11b/g/n wireless LAN module, and then set up your projector and computer for wireless projection. Note: The wireless LAN module is not included with your projector.
The light on the wireless LAN module turns on when the module is installed and operating. The light flashes when the module is communicating over the network.
3. Select the Network menu and press Enter . 4. Select Network Configuration and press Enter . 5. Select the Basic menu and press Enter . 6. Select the Projector Name setting and enter a name up to 16 alphanumeric characters long to identify the projector over the network.
7. Select the Wireless LAN menu and press Enter . 8. Select the settings on the Wireless LAN menu as necessary for your network. Note: Some items may be unavailable if Quick or Advanced connection mode is selected. 9. When you finish selecting settings, select Complete and follow the on-screen instructions to save your settings and exit the menus.
Setting Options Description Connection Mode Quick Selects the type of wireless connection: Advanced Quick : lets you quickly connect to one computer, smartphone, or tablet Advanced : lets you connect .
Selecting Wireless Network Settings in Windows Before connecting to the projector, select the correct wireless network on your computer. 1. To access your wireless utility software, double-click the network icon on the Windows taskbar.
4. Select the Security menu and press Enter . 5. Select the security settings as necessary to match your network settings. 6. When you finish selecting settings, select Complete and follow the on-screen instructions to save your settings and exit the menus.
Using Basic Projector Features Follow the instructions in these sections to use your projector's basic features. Turning On the Projector Turning Off the Projector Viewing 3D Images Selecting the.
1. Open the projector's lens cover. 2. Connect the power cord to the projector's power inlet. 3. Plug the power cord into an electrical outlet. Note: With Direct Power On turned on, the projector turns on as soon as you plug it in. The projector's power light turns blue.
The projector beeps and the Status light flashes blue as the projector warms up. Once the projector is warmed up, the Status light stops flashing and turns blue. Warning: Never look into the projector lens when the lamp is on. This can damage your eyes and is especially dangerous for children.
2. Press the power button again. (To leave it on, press any other button.) The projector beeps twice, the lamp turns off, and the Status light turns off. Note: With Epson's Instant Off technology, there is no cool-down period so you can pack up the projector for transport right away (if necessary).
Parent topic: Using Basic Projector Features Viewing 3D Images You can view 3D images using your projector. Viewing 3D images requires a 3D-compatible video device and a pair of Epson RF 3D glasses (not included with your projector). You can purchase Epson RF 3D glasses from an Epson authorized reseller.
6. Put on the 3D glasses. If you do not see a 3D image, pair the glasses with the projector. Note: If you change the video source or you are not within range of your projector, the glasses enter standby mode and the indicator light flashes green.
5. Move the glasses within 10 feet (3 m) of the projector, then hold down the Pairing button on the glasses for at least three seconds. The status light on the glasses flashes green and red. If pairing is successful, the light turns green for 10 seconds and then turns off.
The glasses are fully charged when the status light on the glasses stays green. Parent topic: Viewing 3D Images 3D Viewing Range When you view 3D images, make sure you are positioned within the viewing range shown here.
3. Select the Extended menu and press Enter . 4. Select the Language setting and press Enter . 5. Select the language you want to use and press Enter .
The foot extends from the projector. 3. Release the lever to lock the foot. 4. If the image is tilted, rotate the rear feet to adjust their height. If the projected image is unevenly rectangular, you need to adjust the image shape.
1. Turn on the projector and display an image. Note: You can display a pattern to aid in adjusting the projected image using the Settings menu. 2. Adjust the slider until the image is evenly rectangular. After correction, your image is slightly smaller.
2. Press one of these keystone buttons on the control panel to display the Keystone adjustment screen. 3. Press a keystone button on the projector's control panel to adjust the image shape.
Resizing the Image With the Zoom Ring 1. Turn on the projector and display an image. Note: You can display a pattern to aid in adjusting the projected image using the Pattern button on the remote control. 2. To enlarge or reduce the image size, rotate the projector's zoom ring.
2. To sharpen the image focus, rotate the projector’s focus ring. Parent topic: Using Basic Projector Features Remote Control Operation The remote control lets you control the projector from almost anywhere in the room. You can point it at the screen, or the front or back of the projector.
1 19.7 feet (6 m) 2 ± 15° 1 19.7 feet (6 m) 2 ± 30° Note: Avoid using the remote control in conditions with bright fluorescent lights or in direct sunlight, or the projector may not respond to commands. If you will not use the remote control for a long time, remove the batteries.
2. For video image sources, insert a DVD or other video media and press its play button, if necessary. 3. Do one of the following: • Press the Source button on the projector until you see the image from the source you want. • Press the button for the source you want on the remote control.
• Front/Ceiling flips the image over top-to-bottom to project upside-down from a ceiling or wall mount. • Rear flips the image horizontally to project from behind a translucent screen. • Rear/Ceiling flips the image over top-to-bottom and horizontally to project from the ceiling and behind a translucent screen.
Image Aspect Ratio The projector can display images in different width-to-height ratios called aspect ratios. Normally the input signal from your video source determines the image's aspect ratio. However, for certain images you can change the aspect ratio to fit your screen by pressing a button on the remote control.
Note: Black bands and cropped images may project in certain aspect ratios, depending on the aspect ratio and resolution of your input signal. Aspect ratio setting Description Auto Automatically sets the aspect ratio according to the input signal. Normal Displays images using the full projection area and maintains the aspect ratio of the image.
2. If you are projecting from a DVD player or other video source, insert a disc or other video media and press the play button, if necessary. 3. Press the Color Mode button on the remote control to change the Color Mode. A list of available Color Modes appears.
Turning On Auto Iris In certain color modes, you can turn on the Auto Iris setting to automatically optimize the image based on the brightness of the content you project. 1. Turn on the projector and switch to the image source you want to use. 2. Press the Menu button.
1. Turn on the projector and start a presentation that includes audio. 2. To lower or raise the volume, press the Volume buttons on the remote control or these buttons on the control panel. A volume gauge appears on the screen. 3. To set the volume to a specific level for an input source, use the projector menus.
Note: For best results, place your files on media that is formatted in FAT16/32. File contents File type Details (extension) Image .jpg Make sure the file is not: • CMYK format • Progressive forma.
2. Do the following as necessary to locate your files: • If you need to display files inside a subfolder on your device, press the arrow buttons to highlight the folder and press the Enter button. • To move back up a folder level on your device, highlight Back to Top and press Enter .
Related tasks Connecting a USB Device or Camera to the Projector Disconnecting a USB Device or Camera From the Projector Slideshow Display Options You can select these display options when using the projector's Slideshow feature.
Setting Options Description Effect Wipe Transitions between images with a wipe effect Dissolve Transitions between images with a dissolve effect Random Transitions between images using a random variet.
Adjusting Projector Features Follow the instructions in these sections to use your projector's feature adjustments. Shutting Off the Picture and Sound Temporarily Projector Security Features Shut.
Locking the Projector's Buttons You can lock the buttons on the projector's control panel to prevent anyone from using the projector. You can lock all the buttons or all the buttons except the power button. 1. Press the Menu button. 2. Select the Settings menu and press Enter .
Unlocking the Projector's Buttons If the projector's buttons have been locked, hold the Enter button on the projector's control panel for seven seconds to unlock them.
Adjusting the Menu Settings Follow the instructions in these sections to access the projector menu system and change projector settings. Using the Projector's Menus Image Quality Settings - Image.
You see the menu screen displaying the Image menu settings. 2. Press the up or down arrow buttons to move through the menus listed on the left. The settings for each menu are displayed on the right. Note: The available settings depend on the current input source.
7. When you finish changing settings on a menu, press Esc . 8. Press Menu or Esc to exit the menus. Parent topic: Adjusting the Menu Settings Image Quality Settings - Image Menu Settings on the Image menu let you adjust the quality of your image for the input source you are currently using.
Setting Options Description Tint Varying levels available Adjusts the balance of green to magenta tones in the image Sharpness Varying levels available Adjusts the sharpness or softness of image details Color Temp.
Input Signal Settings - Signal Menu Normally the projector detects and optimizes the input signal settings automatically. If you need to customize the settings, you can use the Signal menu. The available settings depend on the currently selected input source.
Setting Options Description 3D Setup 3D Display Selects various 3D options 3D Format 3D Display : enables 3D mode 3D Depth 3D Format : selects the 3D format Diagonal Screen Size 3D Depth : sets the de.
Setting Options Description Position Up, down, left, right Adjusts the image location on the screen Auto Setup On Automatically optimizes computer image quality (when Off On) Noise Reduction Off Reduc.
Setting Options Description HDMI Video Range Auto Sets the video range to match the setting of the device Normal connected to the HDMI input port Expanded Auto : detects the video range automatically .
Setting Options Description Keystone H/V-Keystone Adjusts image shape to rectangular (horizontally and Auto V-Keystone vertically) H-Keystone Adjuster H/V Keystone : lets you manually correct horizont.
Setting Options Description HDMI Link Device Connections Adjusts the HDMI Link options; allows the projector remote to HDMI Link control HDMI-connected devices Audio Out Device that support the CEC st.
Setting Options Description Projection Front Selects the way the projector faces the screen so the image is Front/Ceiling oriented correctly Rear Rear/Ceiling User Button 3D Format Assigns a menu opti.
Setting Options Description Operation Direct Power On Selects various operation options Sleep Mode Direct Power On : lets you turn Illumination on the projector without pressing High Altitude Mode the.
Setting Options Description Display Messages Selects various display options Display Background Messages : controls whether messages are displayed on the Startup Screen screen Display Background : sel.
Setting Options Description Net. Info - Wireless LAN Connection mode Displays wireless network status and details Wireless LAN system Antenna level Projector Name SSID DHCP IP Address Subnet Mask Gate.
Projector Information Display - Info Menu You can display information about the projector and input sources by viewing the Info menu. However, you cannot change any settings in the menu. The information displayed depends on the currently selected input source.
Information item Description Deep Color Displays Deep Color information Video Signal Displays the video signal format of the current input source Status Displays information about projector problems t.
Event ID code Cause and solution 0484 Communication with computer was disconnected. Restart the EasyMP Network Projection program. 0483 The EasyMP Network Projection program quit unexpectedly. Check the network communication status, then turn the projector off and then on again.
You cannot reset the following settings using the Reset All option: • PC Signal • Language • Lamp Hours • All settings in the Network menu Parent topic: Adjusting the Menu Settings 91.
Maintaining and Transporting the Projector Follow the instructions in these sections to maintain your projector and transport it from place to place. Projector Maintenance Transporting the Projector Projector Maintenance Your projector needs little maintenance to keep working at its best.
• To remove stubborn smudges, moisten a soft, lint-free cloth with lens cleaner and gently wipe the lens. Do not spray any liquid directly on the lens. Warning: Do not use a lens cleaner that contains flammable gas. The high heat generated by the projector lamp may cause a fire.
• To remove stubborn dirt, use a soft cloth moistened with water and mild soap. Do not spray liquid directly on the projector. Caution: Do not use wax, alcohol, benzene, paint thinner, or other chemicals to clean the projector case. These can damage the case.
2. Gently remove the dust using a small vacuum designed for computers or a very soft brush (such as a paintbrush). Note: You can remove the air filter so you can clean both sides of it. Do not rinse the air filter in water, or use any detergent or solvent to clean it.
2. Carefully open the air filter cover. 3. Pull the air filter out of the projector. Note: Air filters contain ABS resin and polyurethane foam. Dispose of used air filters according to local regulations.
4. Place the new air filter in the projector as shown and push gently until it clicks into place. 5. Close the air filter cover. Parent topic: Air Filter and Vent Maintenance Projector Lamp Maintenance The projector keeps track of the number of hours the lamp is used and displays this information in the projector's menu system.
Replacing the Lamp Before you replace the lamp, let the projector cool down for at least one hour so the lamp will not be hot. Warning: Let the lamp fully cool before replacing it to avoid injury. You can replace the lamp while the projector is mounted to the ceiling, if necessary.
4. Slide the lamp cover out and lift it off. 5. Loosen the screws securing the lamp to the projector. The screws do not come all the way out. 99.
6. Grasp the raised section of the lamp and gently pull the lamp out of the projector. Note: The lamp(s) in this product contain mercury. Please consult your state and local regulations regarding disposal or recycling. Do not put in the trash. 7. Gently insert the new lamp into the projector.
8. Push in the lamp firmly and tighten the screws to secure it. 9. Replace the lamp cover and tighten the screw to secure it. Note: Be sure the lamp cover is securely installed or the lamp will not come on. Reset the lamp timer to zero to keep track of the new lamp’s usage.
Parent topic: Projector Lamp Maintenance Related tasks Resetting the Lamp Timer Resetting the Lamp Timer You must reset the lamp timer after replacing the projector's lamp to clear the lamp replacement message and to keep track of lamp usage correctly.
Replacing the Remote Control Batteries The remote control uses two AA manganese or alkaline batteries. Replace the batteries as soon as they run out. Caution: Use only the type of batteries specified in this manual. Do not install batteries of different types, or mix new and old batteries.
4. Close the battery cover and press it down until it clicks into place. Warning: Dispose of used batteries according to local regulations. Do not expose batteries to heat or flame. Keep batteries out of the reach of children; they are choking hazards and are very dangerous if swallowed.
Solving Problems Check the solutions in these sections if you have any problems using the projector. Projection Problem Tips Projector Light Status Solving Image or Sound Problems Solving Projector or.
1 Power light 2 Status light 3 Lamp light 4 Temp (temperature) light Power light Status light Lamp light Temp light Status and solution Blue Blue Off Off Normal operation. Blue Flashing blue Off Off Warming up. Wait for an image to appear. Blue Off Off Off Standby or sleep mode.
Power light Status light Lamp light Temp light Status and solution Blue Varies Off Flashing Projector is too hot. orange • Make sure that the vents and air filter are not clogged with dust or obstructed by nearby objects. • Clean or replace the air filter.
Power light Status light Lamp light Temp light Status and solution Flashing blue Varies Flashing Off Replace the lamp soon to avoid orange damage. Do not continue using the projector. Off Flashing blue Off Flashing A fan or sensor has a problem. Turn orange the projector off, unplug it, and contact Epson for help.
Solutions When the Image is Not Rectangular Solutions When the Image Contains Noise or Static Solutions When the Image is Fuzzy or Blurry Solutions When the Image Brightness or Colors are Incorrect So.
Solutions When "No Signal" Message Appears If the "No Signal" message appears, try the following solutions: • Press the Source button on the projector repeatedly to cycle through the available sources. Wait a few seconds for an image to appear.
2. Select the Display or Color LCD option, if necessary. 3. Click the Arrange or Arrangement tab. 4. Select the Mirror Displays checkbox. Parent topic: Solutions When "No Signal" Message App.
• If you adjusted the projector height using the projector feet, press the keystone buttons on the projector to adjust the image shape. • Turn on automatic keystone adjustments using the projector's menus. • Adjust the position of the projector's horizontal keystone slider.
Solutions When the Image is Fuzzy or Blurry If the projected image is fuzzy or blurry, try the following solutions: • Adjust the image focus. • Clean the projector lens. Note: To avoid condensation on the lens after bringing the projector in from a cold environment, let the projector warm up to room temperature before using it.
• Make sure all the cables are securely connected to the projector and your video device. If you connected long cables, try connecting shorter cables. • If you are using the ECO Power Consumption setting, try selecting Normal in the projector's menus.
• Avoid using the projector near wireless networks, microwave ovens, 2.4 GHz cordless phones, or other devices that use the 2.4 GHz frequency band. These devices can interfere with the signal between the projector and the 3D glasses. • If the other solutions do not not solve the problem, change the Inverse 3D Glasses setting on the Signal menu.
Related concepts Projector Connections Related tasks Controlling the Volume with the Volume Buttons Solving Projector or Remote Control Operation Problems Check the solutions in these sections if you have problems operating the projector or remote control.
Solutions to Problems with the Remote Control If the projector does not respond to remote control commands, try the following solutions: • Check that the remote control batteries are installed correctly and have power. If necessary, replace the batteries.
Speak to a Support Representative To use the Epson PrivateLine Support service, call (800) 637-7661. This service is available for the duration of your warranty period. You may also speak with a projector support specialist by dialing (562) 276-4394 (U.
Technical Specifications These sections list the technical specifications of your projector. General Projector Specifications Projector Lamp Specifications Remote Control Specifications Projector Dime.
PowerLite Home Cinema 2030 : Normal Power Consumption mode: White light output: 2000 lumens (ISO 21118 standard) Color light output: 2000 lumens ECO Power Consumption mode: White light output: 1400 lu.
Keystone correction angle Vertical: ± 30° (manual or Auto Keystone) Horizontal: ± 30° (manual) USB Type Mini-B port USB 1.1 and 2.0 compliant for service and firmware updating compatibility USB Type A port compatibility One USB 1.
Width 11.69 inches (297 mm) Depth 9.72 inches (247 mm) Weight 6.2 lb (2.8 kg) Parent topic: Technical Specifications Projector Electrical Specifications Rated frequency 50/60 Hz Power supply 100 to 240 VAC ±10% 2.
Operating altitude Up to 4921 feet (1500 m) Up to 9843 feet (3000 m) with High Altitude Mode enabled Parent topic: Technical Specifications Projector Safety and Approvals Specifications United States FCC Part 15 Class B (DoC) UL60950-1 2nd edition (cTUVus Mark) Canada ICES-003 Class B CSA C22.
Display format Refresh rate (in Hz) Resolution (in pixels) SXGA 60 1280 × 960 60 1280 × 1024 WXGA++ 60 1600 × 900 Composite video TV (NTSC) 60 720 × 480 TV (PAL) 50/60 720 × 576 TV (SECAM) 50 720 × 576 TV (NTSC4.
Display format Refresh rate (in Hz) Resolution (in pixels) SDTV (480i/480p) 60 720 × 480 SDTV (576i/576p) 50 720 × 576 HDTV (720p) 50/60 1280 × 720 HDTV (1080i) 50/60 1920 × 1080 HDTV (1080p) 24/3.
Notices Check these sections for important notices about your projector. Recycling Important Safety Information Important Safety Instructions FCC Compliance Statement Trademarks Open Source Software License Copyright Notice Recycling Epson offers a recycling program for end of life products.
Important Safety Instructions Follow these safety instructions when setting up and using the projector: • Do not look into the lens when the projector is on. The bright light can damage your eyes. Avoid standing in front of the projector so the bright light does not shine into your eyes.
• Never allow objects of any kind to enter any openings in the projector. Do not leave objects, especially flammable objects, near the projector. Never spill liquid of any kind into the projector.
• Do not store the projector outside of the required temperature range of 14 to 140 ºF (–10 to 60 ºC) or in direct sunlight for long periods of time. Doing so may cause damage to the case. • Do not place anything that can become warped or damaged by heat near the exhaust vents.
3D Safety Instructions Follow these 3D safety instructions when setting up and using the projector: • If you or any viewer experiences the following symptoms or other major discomfort from viewing 3.
• People who are sleep deprived • People who are physically tired • People under the influence of drugs or alcohol • Anyone who has ever experienced epileptic seizures or sensory disturbances triggered by flashing light effects • SOME LIGHT PATTERNS MAY INDUCE SEIZURES IN PERSONS WITH NO PRIOR HISTORY OF EPILEPSY.
medical equipment related to direct medical care, please make your own judgment on this product's suitability after a full evaluation. Parent topic: Important Safety Instructions FCC Compliance S.
Accolade ® and PrivateLine ® are registered trademarks; Duet TM and SizeWise TM are trademarks; and Epson Store SM and Extra Care SM are service marks of Epson America, Inc. Mac and Mac OS are trademarks of Apple Inc., registered in the U.S. and other countries.
linux-2.6.27 patches udhcp 0.9.8 uvc rev.219 wireless_tools 29 EPSON original drivers Stonestreet One Drivers The GNU General Public License Version 2 is as follows. You also can see the GNU General Public License Version 2 at http://www.gnu.org/licenses/.
Also, for each author's protection and ours, we want to make certain that everyone understands that there is no warranty for this free software. If the software is modified by someone else and pa.
c) If the modified program normally reads commands interactively when run, you must cause it, when started running for such interactive use in the most ordinary way, to print or display an announcemen.
so on) of the operating system on which the executable runs, unless that component itself accompanies the executable. If distribution of executable or object code is made by offering access to copy fr.
This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this License. 8. If the distribution and/or use of the Program is restricted in certain countries .
END OF TERMS AND CONDITIONS How to Apply These Terms to Your New Programs If you develop a new program, and you want it to be of the greatest possible use to the public, the best way to achieve this is to make it free software which everyone can redistribute and change under these terms.
This General Public License does not permit incorporating your program into proprietary programs. If your program is a subroutine library, you may consider it more useful to permit linking proprietary applications with the library. If this is what you want to do, use the GNU Lesser General Public License instead of this License.
This license, the Lesser General Public License, applies to some specially designated software packages--typically libraries--of the Free Software Foundation and other authors who decide to use it.
We call this license the "Lesser" General Public License because it does Less to protect the user's freedom than the ordinary General Public License. It also provides other free software developers Less of an advantage over competing non-free programs.
Activities other than copying, distribution and modification are not covered by this License; they are outside its scope. The act of running a program using the Library is not restricted, and output f.
In addition, mere aggregation of another work not based on the Library with the Library (or with a work based on the Library) on a volume of a storage or distribution medium does not bring the other work under the scope of this License.
Otherwise, if the work is a derivative of the Library, you may distribute the object code for the work under the terms of Section 6. Any executables containing that work also fall under Section 6, whether or not they are linked directly with the Library itself.
It may happen that this requirement contradicts the license restrictions of other proprietary libraries that do not normally accompany the operating system. Such a contradiction means you cannot use both them and the Library together in an executable that you distribute.
It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest validity of any such claims; this section has the sole purpose of protecting the integrity of the free software distribution system which is implemented by public license practices.
THE LIBRARY AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE LIBRARY (INCLUDING BUT .
BSD License (Berkeley Software Distribution License) This projector product includes the open source software program "University of California, Berkeley License (Berkeley Software Distribution License)" which applies the terms and conditions provided by owner of the copyright to the "BSD License".
The "libjpeg" are WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. List of libjpeg programs libjpeg-6b License terms of conditions of each program which are provided by owner of the copyright to the "libjpeg" are as follows.
(3) Permission for use of this software is granted only if the user accepts full responsibility for any undesirable consequences; the authors accept NO LIABILITY for damages of any kind. These conditions apply to any software derived from or based on the IJG code, not just to the unmodified library.
The "libpng" are WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. List of libpng programs libpng-1.2.49 License terms of conditions of each program which are provided by owner of the copyright to the "libpng" are as follows.
libpng versions 0.89, June 1996, through 0.96, May 1997, are Copyright (c) 1996, 1997 Andreas Dilger Distributed according to the same disclaimer and license as libpng-0.88, with the following individuals added to the list of Contributing Authors: John Bowler Kevin Bracey Sam Bushell Magnus Holmgren Greg Roelofs Tom Tanner libpng versions 0.
A "png_get_copyright" function is available, for convenient use in "about" boxes and the like: printf("%s",png_get_copyright(NULL)); Also, the PNG logo (in PNG format, of course) is supplied in the files "pngbar.png" and "pngbar.
jloup@gzip.org Mark Adler madler@alumni.caltech.edu If you use the zlib library in a product, we would appreciate *not* receiving lengthy legal documents to sign. The sources are provided for free but without warranty of any kind. The library has been entirely written by Jean-loup Gailly and Mark Adler; it does not include third-party code.
"Object" form shall mean any form resulting from mechanical transformation or translation of a Source form, including but not limited to compiled object code, generated documentation, and conversions to other media types.
4. Redistribution. You may reproduce and distribute copies of the Work or Derivative Works thereof in any medium, with or without modifications, and in Source or Object form, provided that You meet th.
8. Limitation of Liability. In no event and under no legal theory, whether in tort (including negligence), contract, or otherwise, unless required by applicable law (such as deliberate and grossly neg.
The "aes-src-29-04-09" are WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. List of es-src-29-04-09 programs aes-src-29-04-09 License terms of conditions of each program which are provided by owner of the copyright to the "aes- src-29-04-09" are as follows.
(1) Red Hat Incorporated Copyright (c) 1994-2007 Red Hat, Inc. All rights reserved. This copyrighted material is made available to anyone wishing to use, modify, copy, or redistribute it subject to the terms and conditions of the BSD License.
Permission to use, copy, modify, and distribute this software for any purpose without fee is hereby granted, provided that this entire notice is included in all copies of any software which is or includes a copy or modification of this software and in all copies of the supporting documentation for such software.
29K Support Products Mail Stop 573 5900 E. Ben White Blvd. Austin, TX 78741 800-292-9263 (5) C.W. Sandmann Copyright (C) 1993 C.W. Sandmann This file may be freely distributed as long as the author's name remains. (6) Eric Backus (C) Copyright 1992 Eric Backus This software may be used freely so long as this copyright notice is left intact.
(11) Christopher G. Demetriou Copyright (c) 2001 Christopher G. Demetriou All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1.
San Jose CA 95134 USA (13) Royal Institute of Technology Copyright (c) 1999 Kungliga Tekniska Hökolan (Royal Institute of Technology, Stockholm, Sweden). All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1.
THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
Redistribution and use in source and binary forms is permitted provided that the above copyright notice and following paragraph are duplicated in all such forms. This file is distributed WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.
DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUB.
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
Copyright (c) 2001 Daniel Eischen <deischen@FreeBSD.org>. All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1.
OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
* * * Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. * * Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
of the Software, and to permit persons to whom the Software is furnished to do so, subject to the following conditions: The above copyright notice and this permission notice shall be included in all copies or substantial portions of the Software.
(2) When this software is redistributed in a form in which it can be used in the development of other software, library form, etc., the above copyright display, these terms of utilization, and the following stipulation of no guarantee shall be inserted in documentation accompanying redistribution (user's manual, etc.
1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
stipulation of no guarantee shall be inserted in documentation accompanying redistribution (user's manual, etc.). (3) When this software is redistributed in a form in which it cannot be used in the development of other software, embedded in devices, etc.
Seiko Epson Corporation shall not be liable for any damages or problems arising from the use of any options or any consumable products other than those designated as Original Epson Products or Epson Approved Products by Seiko Epson Corporation. This information is subject to change without notice.
デバイスEpson PowerLite Home Cinema 2030の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Epson PowerLite Home Cinema 2030をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはEpson PowerLite Home Cinema 2030の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Epson PowerLite Home Cinema 2030の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Epson PowerLite Home Cinema 2030で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Epson PowerLite Home Cinema 2030を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はEpson PowerLite Home Cinema 2030の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Epson PowerLite Home Cinema 2030に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちEpson PowerLite Home Cinema 2030デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
