EpsonメーカーPP-7000IIの使用説明書/サービス説明書
ページ先へ移動 of 40
Rev.: B0 Aura Series (PP - 7000II / PP - 7000 IIUSB) Thermal Printer IMPORTANT!!!! Please read carefully before using this printer Before opening the Top Hood, make sure there is no paper ja m or cutter jam trouble. (Read page 3 - 4 , 3 - 5 and Warranty Limit in the user’s Manual.
P/N: 19370900040 Federal Communications Commission Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.
i Table Of Contents GETTING STARTED . . . . . . . . . . . . . . . . . . . . . 1 -- 1 CONGRATULATION . . . . . . . . . . . . . . . . . . . . . . 1 -- 1 PRODUCT BRI EFING . . . . . . . . . . . . . . . . . . . . . 1 -- 1 UNPACKING . . . . . . . . . . . .
ii GENERAL CLEANING . . . . . . . . . . . . . . . . . . . . 3 -- 1 PRINT HEAD CLEANING . . . . . . . . . . . . . . . . . 3 -- 1 TROUBLE SHOOTING . . . . . . . . . . . . . . . . . . . . 3 -- 2 General problems . . . . . . . . . . . . . . . . . . . . . 3 -- 2 Printing problems .
1 - 1 I. GETTING STARTED A. CONGRATULATION You have made a very wise decision by purchasing the eas y loading; low noise; high resolution; light weight; high reliability thermal printer Aura (PP - 7000II & PP - 7000IIUSB) series of Posiflex products.
1 - 2 The Aura PP - 7000II & PP - 7000IIUSB supports a guillotine type auto cutter for paper partial cut and a manual cut mechanism. The Aura series also supports user’s compan y’s LOGO downloading for superior performance. It even supports some enhancement capability for reminder function to persons around.
1 - 3 Length of the interface cable depends on whether the order includes the po wer adaptor. When power adaptor is included, the interface cable is 6 ft long for stand alone application. When the power adaptor is not included in the order, the interface cable is a shorter one for integrated application in Posiflex POS system.
1 - 4 E. MAIN PARTS ON THE EXTERIOR Front View Bottom View Bottom Cov er Power LED Error LED Paper Out LED FEED Switch Top Hood Top Cover Hood Release Power Switch Cutter Cover Power Switch Screws Win.
1 - 5 F. INDICATORS • Power LED: green • Error LED: red • Paper Out LED: red G. OPERATING ENVIRONMENT • Place t he printer on a sturdy, level surface. • Choose a place that is well ventilated and free of excessive dust, smoke or fume. • Do not put the printer under direct sunlight or near a heater.
1 - 6 • Since the paper roll is highly thermal sensitive, please keep them in a dark place that is 20º and 65% RH when not installed in the printer. • Use a grounded AC power outlet. • Use only the power cord and power adaptor furnished wit h the printer.
1 - 7 • Use of volatile organic solvents such as alcohol, ester and ketone on thermal paper can cause discoloration. • Some adhesiv e tapes on thermal paper may cause discoloration or faded printing. • Use only products made from polyethylene, polypropylene or polyester for storage of thermal paper.
.
2 - 1 II. QUICK START - UP A. LOADING PAPER 1. Desk top application 1. Slide the hood lock toward the front of the printer to release the hood. 2. Raise the released hood wide ope n manually. 3. Drop the thermal paper roll inside the printer in the orientation as shown in the picture.
2 - 2 2. When t o replace paper Whenever the printer gives paper out signal or a red line appears on the thermal paper, it is the proper timing for replacing the paper.
2 - 3 please adjust in setup window the switch positions both 1, and 2 to ON leaving the rest unchanged as fac tory default setting . 3. USB connection The USB cable used to connect the USB interface .
2 - 4 Follow the wizard and browse to the folder that holds the driver and specify this location for the wizard. Keep on following the wizard and it will come to a “Finish”. The process in “Add/New Hardware Wizard” for Win98 is also very similar to what shown here for Win2000/XP.
2 - 5 Follow the wizard and browse to the folder that holds the driver and specify this location for the wizard again. The process for this stage USB serial port converter driver installation is quite similar to the last stage for the USB printer device driver.
2 - 6 port assignment setup will be required to use the USB printer as if a normal serial printer. The procedures described below may also be engaged any time whenever a re - assignment of the COM port number is required.
2 - 7 the Posiflex USB interface thermal printer will operate the same way as if a RS232 serial printer connected on the COM port specified. Please note that it is allowed to apply more than one Posiflex USB printer in one setup because each Posiflex USB printer may carry different internal ID.
2 - 8 5. Power c onnection The power connector is a 3 pin jack between the peripheral connector and the parallel connector for PP - 7000II and is at the rightmost for PP - 7000IIUSB. Either a Posiflex supplied power adaptor or a printer power cable from a Posiflex POS system c an be connected to this connector to supply power for this printer.
2 - 9 The header is printed in text mode and the rest part of this slip is printed in page mode. If FEED button is pressed at this moment, a font table will be printed in text mode again. To exit the test printing, p lease turn the printer off and on again.
2 - 10 release the fixing screw to adjust the position of sensor head. The acceptable paper roll bobbin outer diameter is between 18 and 22mm. This adjus tment allows sensor activation on paper roll overall diameter between 21 and 23.6 mm unless for too light bobbins.
2 - 11 accessory of the printer. If the user uses narrower paper roll and requires more spacer plates, it can be purchased from Posiflex. 4. Paper cutting The paper advance after a p rotective cut is now set to 12 mm.
.
3 - 1 III. MAINTENANCE GUIDES A. MAINTENANCE GUIDE LINES • Always turn off and disconnect power before opening the cover. • The areas around the print head and motor bec ome very hot during and just after printing, do not touch them.
3 - 2 Before p utting back the paper roll for printing, alcohol solvent must be dried completely. D. TROUBLE SHOOTING This section gives solutions to some printer problems you may have.
3 - 3 If there is no paper jam and the print head is not overheated, turn off the printer and wait for half a minute th en turn it back on. If the problem still remains, contact a qualified service person. Nothing can be printed with ERROR LED OFF – Try to run self test according to previous chapter to check if the printer itself works properly.
3 - 4 3. Paper Jam Problems Paper is jammed inside the printer – Turn off the printer and open the print hood by releasing the hood lock. Remove the jammed paper and reinstall the paper roll. Close the hood prope rly and firmly. Then turn on the printer for operation.
3 - 5 5. Advanced Analysis Tool Thi s printer supports Hexadecimal Dump for experienced user to view exactly what data is received by the printer. This can be useful in finding software problems. To start the dump mode: Turn off printer; Open print hood; Hold down FEED button while turning p rinter on; Close the hood.
.
4 - 1 IV. SPECIFICATIONS A. PRINTER ITEM SPECIFICATION Printing method T hermal sensitive line dot method Effective printing width 64 mm Thermal head configuration 512 dots / line Printing speed 180 mm /sec.
4 - 2 C. POWER ADAPTOR ITEM REQUIREMENT INPUT VOLTAGE 100 V AC ~ 250 V AC INPUT FREQUEN CY 50 ~ 60 HZ INPUT CURRENT 1.5 A MAX. @ 115 V AC OUTPUT VOLTAGE + 24 V DC OUTPUT POWER 60 W STATIC LOAD 0 A ~ 2.
5 - 1 V. TECHNICAL INFORMATION A. INTERFACES 1. Periphe ral interface The connector for peripheral control is a 6P6C RJ11 jack with the following pin assignment. The best recommended cash drawers to this connector are Posiflex CR3100, CR3200, CR4000 and CR4100.
5 - 2 B. SETUP WINDOW On bottom cover of the Aura series thermal printer, there is screwed a metal plat e for setup window. In this window, there is a 8 position DIP switch for printer setup. Please use proper tool to change the switch setting when necessary.
5 - 3 Switch position 4 defines the handshaking method in serial interface. When it is set to ON, the printer transmits an “XOFF” for busy and sends an “XON” for not busy. When it is set to OFF, the printer signifies the busy status over hardware signals that can be detected by the host as “DSR” or “CTS”.
5 - 4 Switch Positio n 1 2 3 4 5 6 7 8 Serial interface w/ auto cutter OFF OFF OFF OFF OFF OFF OFF OFF Parallel interface w/ auto cutter ON ON OFF OFF OFF OFF OFF OFF C. INTERNAL SWITCH There is an extra internal 4 position DIP switch in PP - 7000II for more technical settings.
5 - 5 D. SOFTWARE COMMANDS The Aura thermal printer supports all commands applicable to Epson printer TM - T88II. The only di fference is the smoothening command in enlarged text fonts. Please visit our web site http://www.posiflex.com or http://www.posiflex.
5 - 6 This command defines length of beep as m seconds when beep command is received. When m = 0, default applies. ESC ‘p’ m n1 n2: Kitchen bell drive command (m = ‘0’, 0 ≦ n1 ≦ n2 ≦ 255.
5 - 7 E. CHARACTER CODE PAGES Aura PP - 7000II & PP - 7000IIUSB series support all code pages and international character sets applicable to Epson printer TM - T88 .
5 - 8 If any undefined c ode (<00> to <1F>) or an undefined <ESC>, <FS>, or <GS> command sequence beyond these tables is received, the code or the sequence of codes will be discarded. (However, when image print data, character registration data, or command parameters are received, they are handled as ordinary data.
デバイスEpson PP-7000IIの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Epson PP-7000IIをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはEpson PP-7000IIの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Epson PP-7000IIの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Epson PP-7000IIで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Epson PP-7000IIを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はEpson PP-7000IIの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Epson PP-7000IIに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちEpson PP-7000IIデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
