EpsonメーカーPRP-080の使用説明書/サービス説明書
ページ先へ移動 of 19
PRP-080 Series THERMAL RECEIPT PRINTER User's Manual Specifications subjects to change without notice.
-1- Contents 1. General Information 2. Quick Start 3. Printer Interface and Connection 4. Configuration 5. Safety and Maintenance 6. Appendix 1.1) Main Features...................................................................... 2 1.2) PRP-080I (Standard) & PRP-080II (Advanced) Function Comparison 2.
1. General Information Models 1.1) Main Features Note: International font can be combined with others, for example PRP-080I-BI-MS, standard, Big5+International, beige, serial 160 (for PRP-080II)~220 (for PRP-080I) mm/s maximum print speed. Low-noise thermal printing.
1. General Information Models 1.1) Main Features Note: International font can be combined with others, for example PRP-080I-BI-MS, standard, Big5+International, beige, serial 160 (for PRP-080II)~220 (for PRP-080I) mm/s maximum print speed. Low-noise thermal printing.
2. Quick Start 2.1) Unpacking & Parts Identification a. Unpacking: B. Parts Identification: -5- -4- Printer cover Open this cover to load or replace paper . Control panel Features LED indicators to indicate printer status and buttons to operate the printer .
c. While observing the direction of the roll, set the paper roll into the hollow , and pull on the leading edge of the paper toward you as shown: d. Close the cover: When closing the cover , press the center of printer cover firmly to prevent paper miss-loading -7- -6- e.
3. Printer Interface and Connection 3.1) Connecting the Interface Cable 3.2) Connecting to a Cash Drawer a. Before connecting/disconnecting the interface cable, make sure that power to the printer and all the devices connected to the printer is turned off.
(Blue LED) The POWER light is on whenever the printer is on. (Red LED) This indicates printer online/offline status or an error (Button) Press the FEED button to feed roll paper . (Button) Press the ONLINE button to set printer ONLINE/OFFLINE 4. Configuration Printer Control Panel & Status Indication 4.
4.3) Printer Self T est 4.4) Driver Installation This is to test whether the printer is working properly or not and also checks the printing quality , firmware version, and DIP switch settings 1. Hold the ONLINE (*) button first and then turn on the power at the same time, release the button after around 1 second.
5. Safety and Maintenance 5.1) Safety Information 5.2) Periodical Cleaning 5.3) Preventing Paper Jams 1. Do not touch the HEAD of printer with anything. 2. Do not touch the cutter blade. 3. Only use the power supply that is come along with the printer .
6. Appendix 1. Pr oduct Specifications 1.1) Printing Specifications 1.2) Auto Cutter 1.3) Paper Roll Supply Device 1. Printing method: Thermal line printing 2. Dot density: 203 dpi 203 dpi. 3. Printing direction: Unidirectional with friction feed 4. Printing width: 72 mm (2.
1.7) Reliability 1.8) Environmental Conditions 1.9) Installation 1. Life Span: Mechanism: 15,000,000 lines Thermal head: 100 million pulses, 100 Km Auto cutter: 1,500,000 cuts (End of life span is defined to have reached the end of its life when it reaches the beginning of the W ear out Period.
1.nterface connector terminal assignments and signal functions Pin number Signal name Signal Source Description 2 TXD Printer When using XON/XOFF handshake protocol, printer transmits control code XON.
-23- -22- 3. Drawer kick-out drive signal Output signal: Output voltage: Approximately 24 V Output current: 1A or less 2.2) Connectors a. Interface Connectors b.
General Printer Commands Command Lists: -25- -24- Command Code Description Function Description (Hex) HT 09 Horizontal tab LF 0A Print and line feed CR 0D Print and carriage return E S C$n L n H 1 B2 .
PRP-080I & II COMMANDS COMP ARISON Command Name PRP-080I PRP-080II (Standard) (Advanced) HT Horizontal tab * * LF Print and line feed * * FF Print and return to standard * mode in page mode CR Pri.
Note: Commands for International Fonts E S CRn Select an International Character Set Format ASC ESC R n Hex 1B 52 n Decimal 27 82 n Range 0 n 13 Description Selects an international character set n from the following table: N Character set 0 U.S.A. 1 Franch 2 Germany 3 U.
Character code can also be selected by utility pr ogram. 1. T o install the PRP-080 Default Code Page Setting utility , please insert the bundled CD disk into the CD-ROM drive. 2. In the CD-Rom menu, please go to Receipt Printer > PRP-080 > Code Page and double click the setup.
Optional multilingual character model supports printing with one of the following characters: T o enable/disable the multilingual character code use the following commands: (*) a. B - T raditional Chinese (Big 5) b. G - Simplify Chinese (GB) c. K - Korean d.
デバイスEpson PRP-080の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Epson PRP-080をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはEpson PRP-080の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Epson PRP-080の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Epson PRP-080で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Epson PRP-080を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はEpson PRP-080の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Epson PRP-080に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちEpson PRP-080デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。