EpsonメーカーRP-300-Hの使用説明書/サービス説明書
ページ先へ移動 of 31
RP-30 0 - H Receipt Printer User ’ s Manua l All specifications are subject to change without notice.
.
T ABLE OF CONTENTS 1. Parts Identifications 3 2. Setting up the printer 4 2.1 Unpacking 4 2.2 Connecting the cables 5 2.3 Loading the roll paper 9 2.4 Dip switch setting 11 3. Control panel and other functions 18 3.1 Control panel 18 3.2 Error Indicating 18 4.
RP-300-H User ’ s Manual 3 1. Parts Identifications.
RP-300-H User ’ s Manual 4 2. Setting Up the Printer 2-1. Unpacking Y our printer box should include these items. If any items are damaged or missing, please contact your dealer for assistance.
RP-300-H User ’ s Manual 5 2-2. Connecting the Cables Y ou can connect up the cables required for printing to the printer . They all connect to the connector panel on the back of the printer , which is shown below : Before connecting any of the cables, make sure that both the printer and the computer are turned off.
RP-300-H User ’ s Manual 6 2-2-1. Interface Connector - Serial interface PIN SIGNAL I/O DESCRIPTION 2 TxD Output Printer transmit data line RS-232C level 3 RxD Input Printer receive data line RS-232.
RP-300-H User ’ s Manual 7 - Centronics Parallel interface PIN SIGNAL I/O DESCRIPTION 1 STROBE- Input Synchronize signal Data received 2~9 DA T A0~7 Input/Output Data bit T ransmitted 0 ~7 10 ACK- Output Data receiving completed.
RP-300-H User ’ s Manual 8 2-2-2. Cash Drawer Connector The printer can operate two cash drawers with a 6 pin RJ-1 1 modular connector . The driver is capable of supplying a maximum current of 1.
RP-300-H User ’ s Manual 9 2-3. Loading the Roll Paper Notes: Be sure to use paper rolls that meet the specifications. Do not use paper rolls that have the paper glued to the core because the printer cannot detect the paper end correctly . (T urn off power switch) 1.
RP-300-H User ’ s Manual 10 5. Be sure to note the correct direction that the paper comes off the roll. 6. Pull out a small amount of paper , as shown.
RP-300-H User ’ s Manual 1 1 2-4. Dip Switch Setting The printer is set up at the factory to be appropriate for almost all users. On the other hand, offers some more settings for users with special requirements. It has DIP switches that allow you to change communication setting, such as handshaking and parity check, as well as print density .
RP-300-H User ’ s Manual 12 2-4-2. Parallel Interface Specification DIP Switch Set 1 Functions SW FUNCTIONS ON OFF DEF AUL T 2 Hexadecimal HEXDUMP NORMAL OFF 5 Bi-Parallel mode DISABLED ENABLED OFF Print Density (DIP-SW2) Print Density SW -1 SW-2 Low Power ON ON Normal OFF ON Normal ON OFF Dark OFF OFF 2-4-3.
RP-300-H User ’ s Manual 13 2-4-4. USB Interface Specification DIP Switch Set 1 Function SW FUNCTION ON OFF DEF AUL T 2 Hexadecimal HEXDUMP NORMAL OFF Print Density (DIP-SW2) Print Density SW -1 SW.
RP-300-H User ’ s Manual 14 2-4-5. Wi-fi Specification DIP Switch Set 1 Function SW FUNCTION ON OFF DEF AUL T 2 Hexadecimal HEXDUMP NORMAL OFF Print Density (DIP-SW2) Print Density SW -1 SW-2 Low Power ON ON Normal OFF ON Normal ON OFF Dark OFF OFF 2-4-6.
RP-300-H User ’ s Manual 15 DIP Switch Set 2 Functions Cutter SW FUNCTIONS ON OFF Remarks 3 Cutter FULL CUT P ARTIAL CUT Only Epson mode Emulation FUNCTIONS SW-4 SW-5 Epson (TM-88) OFF OFF Paper low detect (*1) SW FUNCTIONS ON OFF 6 Paper Low Detect Do not Detect (*1) The detecting function of [Paper Low] is an option.
RP-300-H User ’ s Manual 16 ♣CAUTION: T urn off the printer while removing the DIP switch cover to prevent an electric short, which can damage the printer . 1. Make sure the printer is turned off. 2. Remove the screw from the DIP switch cover . Then, take off the DIP switch cover as shown in the illustration below .
RP-300-H User ’ s Manual 17 ♣CAUTION: When the paper is jammed with cutter , the top cover might be stuck. In this case, repeat power on and off several times. If the top cover is still stuck, please follow the steps to release the papers from jamming.
RP-300-H User ’ s Manual 18 3. Control panel and other functions. 3-1. Control panel Y ou can control the basic paper feeding operations of the printer with the button on the control panel. The indicator lights help you to monitor the printer ’ s status.
RP-300-H User ’ s Manual 19 4. Self T est The self-test lets you know if your printer is operating properly . It checks the control circuits, printer mechanisms, print quality , ROM version and DIP switch settings. This test is independent of any other equipment or software.
RP-300-H User ’ s Manual 20 5. Hexadecimal Dump This feature allows experienced users to see exactly what data is coming to the printer . This can be useful in finding software problems.
RP-300-H User ’ s Manual 21 6. Specifications Appendix A : Specifications 6-1. General Specifications (1) Printing Method Direct line thermal printing. (2) Print speed 200mm/sec. (3) Dot density 180DPI(Hor/V er) 180 / 180 (0.142mm / 0.142mm dot) (4) Printing Width 180DPI Max 72mm (512dots) (5) Number of print columns.
RP-300-H User ’ s Manual 22.
RP-300-H User ’ s Manual 23 6-2. Auto Cutter Specifications (1) Cutting Frequency Max. 30 cuts per minute (2) Thickness of paper 0.06 ~ 0.09 mm (3) Cutter Life 1.
RP-300-H User ’ s Manual 24 ♠Important! When connecting or disconnecting the power supply from the printer , be sure that the following cautions are observed. (1) Use a power supply (Limited Power Supply) of DC 24V � 10% and more than 2.5A. (2) Be careful about installin gthe printer in an area where there is noise.
RP-300-H User ’ s Manual 25 7. Command List No. Command Function REMARKS 1 HT Horizontal tab 2 LF Print and line feed 3 CR Print and carriage return 4 FF Print and return to standard mode(in page mo.
RP-300-H User ’ s Manual 26 No. Command Function REMARKS 39 ESC p General pulse 40 ESC t Select character code table 41 ESC { T urn upside-down printing mode on/off 42 FS p Print NV bit image 43 FS .
RP-300-H User ’ s Manual 27.
RP-300-H User ’ s Manual 28 ♣ 注 意 事項 : 在 移 除 DIP switch 蓋 子 前 , 須 先 將 printer 電 源 關 掉 , 以 免 發 生 短路 導致 printer 燒 毀 . 1. 先 確 認 printer 電 源 確 實 關 閉 2. 移 除 DIP switch 蓋 子 上 之 螺 絲 , 再 將 蓋子 打開 , 如 圖 示 3.
RP-300-H User ’ s Manual 29 ♣ 注 意 事項 : 當 列 印 紙 切 割 跳 脫 或 卡住 時, 可 能 是 被 上 端 蓋 子 卡 住 . 在 此 種 狀 況 下 , 請 重 複 將 電 源 開 關 數 次 . 如 果 故 障 仍 無 法 排 除 ,請 依循 以 下 步 驟 排 除 故 障 1 .
Rev . 1. 0.
デバイスEpson RP-300-Hの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Epson RP-300-Hをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはEpson RP-300-Hの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Epson RP-300-Hの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Epson RP-300-Hで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Epson RP-300-Hを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はEpson RP-300-Hの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Epson RP-300-Hに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちEpson RP-300-Hデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
