EquatorメーカーWB 818の使用説明書/サービス説明書
ページ先へ移動 of 13
E Q U A TO R Adv a nce d A pp lia nce s SER VIC E M ANU AL SP A RE P ART S C A T ALOG A ND F i rs t Edi tion - Mar ch 20 0 5 18" DIS H WA S HER S M O D E L: WB 818 SB 818 w w w .
CONTENTS SPECIFICATIONS …………………………………… 3 SCHEMATIC DIAGRAM ……………………………… 4 WIREING DIAGRAM …………………………………… 5 TIMER CYCLE C.
SPECIFICA TION MODEL ELECTRICAL Rating 120V 60Hz Motor (HP) 1/5 Motor (Amps) Heater W attage 1000W Wa s h T otal Amps (Load Rated) 9.2A Thermostat Contacts Close at 127 ° F ± 5 ° F 58 ℃ ± 3 ℃ W A TER SUPPL Y Suggested Min.
4 T R 1 0 R 1 1 3 A C L 5 ITR(78) 1 5 6 R Y 2 A C N R Y 1 D / E d c o n t o l l e r 1 6 7 1 7 T R 8 T R 9 T R 7 E V 2 8 1 8 E V 1 9 1 9 T R 6 T R 5 T R 4 T R 3 B U Z D 9 D 1 1 D 1 0 V C C 1 5 1 6 8 IS.
5 ITR(78) green R 1 red green P S M L s o f t e n e r v a l v e p o w e r s w i t c h w a s h i n g p u m p r i n s e a i d w a r n i n g l i g h t w a t e r l e v e l s w i t c h t h e r m i c - h y .
TIMER CYCLE CHAR T COMPONENT OPERA TION AND REP AIR SAFETY PRECA TIONS Always turn off the electric power supply before servicing any electrical component, making ohmmeter checks, or r eplacing any parts. All voltage checks should be made with a voltmeter having a full scale range of 130 volts or higher .
POWER BUTTON Figure 1 Figure 2 3. Remove the screws which locking the co ntrol panel (See figure1). Remove the power button and unscrew the scr ews which locking the circuit board behind the contr ol panel. (See Figure 2 and 3.) 4. T ake down the damaged cir cuit board and install a new circuit board , r everse procedur es to complete repairs.
T o Replace Door Latch Assembly 1. Disconnect dishwasher fr om electrical supply . 2. Remove screws securing the control panel to the inner door . 3. Remove wir e leads from d oor latch and r emove screws securing door latch as sembly to inner door . (See Figure 5.
F i g u r e 7 F i g u r e 8 T o Remove Or Replace Float Switch 1. Disconnect dishwasher from electrical supply . 2. Remove electrical leads to float switch. 3. T ake down the switch fr om float support. 4. Install new float switch and reverse pr ocedures to complete r epairs (See figure 6).
TROUBLESHOOTING The troubleshooting cheek lis t is common for all d ishwasher models. They use different parts to accomplish the same thing and diagnosis w ill remain similar . When a problem arises, and a possible caus e is lis ted, follow the test, remove o r replace pr ocedures as outline in this serv ice manual.
start or run. ● Motor (bad bearings or locked rot or ) . ◇ Replace motor . Motor trips out on in terminal thermal overload protector . ● S tart relay not dropping out. ● Improper voltage. ● Seal faces binding. ● Motor shaft binding. ● Motor windings shorted.
● Overcharge of water . ● T ub seal (torn, worn or loose). ● Dishwasher door not sealing properly . ● Dishwasher is not level. ● Overburden (w rong type of detergent). ● Hose clamps loose. ● Heater el ement mounting nuts loose. ● W ater seal leaking.
● Defective seal on plunger . ● Over filling container . ◇ Replace plunger . ◇ Follow instructions in o wner ’ s manual. Noisy pump assembly . ● Impellers not properly shimmed or rubbing. ● Pump parts not properly installed. ● Debris in bottom of tub sump area.
デバイスEquator WB 818の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Equator WB 818をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはEquator WB 818の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Equator WB 818の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Equator WB 818で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Equator WB 818を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はEquator WB 818の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Equator WB 818に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちEquator WB 818デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。